12 files changed, 838 insertions, 210 deletions

diff --git a/Documentation/ABI/testing/sysfs-class-regulator b/Documentation/ABI/testing/sysfs-class-regulator
new file mode 100644
index 000000000000..79a4a75b2d2c
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-class-regulator
@@ -0,0 +1,315 @@
+What:           /sys/class/regulator/.../state
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                state. This holds the regulator output state.
+
+                This will be one of the following strings:
+
+                'enabled'
+                'disabled'
+                'unknown'
+
+                'enabled' means the regulator output is ON and is supplying
+                power to the system.
+
+                'disabled' means the regulator output is OFF and is not
+                supplying power to the system..
+
+                'unknown' means software cannot determine the state.
+
+                NOTE: this field can be used in conjunction with microvolts
+                and microamps to determine regulator output levels.
+
+
+What:           /sys/class/regulator/.../type
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                type. This holds the regulator type.
+
+                This will be one of the following strings:
+
+                'voltage'
+                'current'
+                'unknown'
+
+                'voltage' means the regulator output voltage can be controlled
+                by software.
+
+                'current' means the regulator output current limit can be
+                controlled by software.
+
+                'unknown' means software cannot control either voltage or
+                current limit.
+
+
+What:           /sys/class/regulator/.../microvolts
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                microvolts. This holds the regulator output voltage setting
+                measured in microvolts (i.e. E-6 Volts).
+
+                NOTE: This value should not be used to determine the regulator
+                output voltage level as this value is the same regardless of
+                whether the regulator is enabled or disabled.
+
+
+What:           /sys/class/regulator/.../microamps
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                microamps. This holds the regulator output current limit
+                setting measured in microamps (i.e. E-6 Amps).
+
+                NOTE: This value should not be used to determine the regulator
+                output current level as this value is the same regardless of
+                whether the regulator is enabled or disabled.
+
+
+What:           /sys/class/regulator/.../opmode
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                opmode. This holds the regulator operating mode setting.
+
+                The opmode value can be one of the following strings:
+
+                'fast'
+                'normal'
+                'idle'
+                'standby'
+                'unknown'
+
+                The modes are described in include/linux/regulator/regulator.h
+
+                NOTE: This value should not be used to determine the regulator
+                output operating mode as this value is the same regardless of
+                whether the regulator is enabled or disabled.
+
+
+What:           /sys/class/regulator/.../min_microvolts
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                min_microvolts. This holds the minimum safe working regulator
+                output voltage setting for this domain measured in microvolts.
+
+                NOTE: this will return the string 'constraint not defined' if
+                the power domain has no min microvolts constraint defined by
+                platform code.
+
+
+What:           /sys/class/regulator/.../max_microvolts
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                max_microvolts. This holds the maximum safe working regulator
+                output voltage setting for this domain measured in microvolts.
+
+                NOTE: this will return the string 'constraint not defined' if
+                the power domain has no max microvolts constraint defined by
+                platform code.
+
+
+What:           /sys/class/regulator/.../min_microamps
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                min_microamps. This holds the minimum safe working regulator
+                output current limit setting for this domain measured in
+                microamps.
+
+                NOTE: this will return the string 'constraint not defined' if
+                the power domain has no min microamps constraint defined by
+                platform code.
+
+
+What:           /sys/class/regulator/.../max_microamps
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                max_microamps. This holds the maximum safe working regulator
+                output current limit setting for this domain measured in
+                microamps.
+
+                NOTE: this will return the string 'constraint not defined' if
+                the power domain has no max microamps constraint defined by
+                platform code.
+
+
+What:           /sys/class/regulator/.../num_users
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                num_users. This holds the number of consumer devices that
+                have called regulator_enable() on this regulator.
+
+
+What:           /sys/class/regulator/.../requested_microamps
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                requested_microamps. This holds the total requested load
+                current in microamps for this regulator from all its consumer
+                devices.
+
+
+What:           /sys/class/regulator/.../parent
+Date:           April 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Some regulator directories will contain a link called parent.
+                This points to the parent or supply regulator if one exists.
+
+What:           /sys/class/regulator/.../suspend_mem_microvolts
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_mem_microvolts. This holds the regulator output
+                voltage setting for this domain measured in microvolts when
+                the system is suspended to memory.
+
+                NOTE: this will return the string 'not defined' if
+                the power domain has no suspend to memory voltage defined by
+                platform code.
+
+What:           /sys/class/regulator/.../suspend_disk_microvolts
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_disk_microvolts. This holds the regulator output
+                voltage setting for this domain measured in microvolts when
+                the system is suspended to disk.
+
+                NOTE: this will return the string 'not defined' if
+                the power domain has no suspend to disk voltage defined by
+                platform code.
+
+What:           /sys/class/regulator/.../suspend_standby_microvolts
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_standby_microvolts. This holds the regulator output
+                voltage setting for this domain measured in microvolts when
+                the system is suspended to standby.
+
+                NOTE: this will return the string 'not defined' if
+                the power domain has no suspend to standby voltage defined by
+                platform code.
+
+What:           /sys/class/regulator/.../suspend_mem_mode
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_mem_mode. This holds the regulator operating mode
+                setting for this domain when the system is suspended to
+                memory.
+
+                NOTE: this will return the string 'not defined' if
+                the power domain has no suspend to memory mode defined by
+                platform code.
+
+What:           /sys/class/regulator/.../suspend_disk_mode
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_disk_mode. This holds the regulator operating mode
+                setting for this domain when the system is suspended to disk.
+
+                NOTE: this will return the string 'not defined' if
+                the power domain has no suspend to disk mode defined by
+                platform code.
+
+What:           /sys/class/regulator/.../suspend_standby_mode
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_standby_mode. This holds the regulator operating mode
+                setting for this domain when the system is suspended to
+                standby.
+
+                NOTE: this will return the string 'not defined' if
+                the power domain has no suspend to standby mode defined by
+                platform code.
+
+What:           /sys/class/regulator/.../suspend_mem_state
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_mem_state. This holds the regulator operating state
+                when suspended to memory.
+
+                This will be one of the following strings:
+
+                'enabled'
+                'disabled'
+                'not defined'
+
+What:           /sys/class/regulator/.../suspend_disk_state
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_disk_state. This holds the regulator operating state
+                when suspended to disk.
+
+                This will be one of the following strings:
+
+                'enabled'
+                'disabled'
+                'not defined'
+
+What:           /sys/class/regulator/.../suspend_standby_state
+Date:           May 2008
+KernelVersion:  2.6.26
+Contact:        Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+                Each regulator directory will contain a field called
+                suspend_standby_state. This holds the regulator operating
+                state when suspended to standby.
+
+                This will be one of the following strings:
+
+                'enabled'
+                'disabled'
+                'not defined'
diff --git a/Documentation/hwmon/dme1737 b/Documentation/hwmon/dme1737
index 8f446070e64a..b1fe00999439 100644
--- a/Documentation/hwmon/dme1737
+++ b/Documentation/hwmon/dme1737
@@ -22,6 +22,10 @@ Module Parameters
                         and PWM output control functions. Using this parameter
                         shouldn't be required since the BIOS usually takes care
                         of this.
+* probe_all_addr: bool  Include non-standard LPC addresses 0x162e and 0x164e
+                        when probing for ISA devices. This is required for the
+                        following boards:
+                        - VIA EPIA SN18000
 
 Note that there is no need to use this parameter if the driver loads without
 complaining. The driver will say so if it is necessary.
diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index 9549237530cf..6d41db7f17f8 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -96,11 +96,6 @@ initial testing of the ADM1027 it was 1.00 degC steps. Analog Devices has
 confirmed this "bug". The ADT7463 is reported to work as described in the
 documentation. The current lm85 driver does not show the offset register.
 
-The ADT7463 has a THERM asserted counter. This counter has a 22.76ms
-resolution and a range of 5.8 seconds. The driver implements a 32-bit
-accumulator of the counter value to extend the range to over a year. The
-counter will stay at it's max value until read.
-
 See the vendor datasheets for more information. There is application note
 from National (AN-1260) with some additional information about the LM85.
 The Analog Devices datasheet is very detailed and describes a procedure for
@@ -206,13 +201,15 @@ Configuration choices:
 
 The National LM85's have two vendor specific configuration
 features. Tach. mode and Spinup Control. For more details on these,
-see the LM85 datasheet or Application Note AN-1260.
+see the LM85 datasheet or Application Note AN-1260. These features
+are not currently supported by the lm85 driver.
 
 The Analog Devices ADM1027 has several vendor specific enhancements.
 The number of pulses-per-rev of the fans can be set, Tach monitoring
 can be optimized for PWM operation, and an offset can be applied to
 the temperatures to compensate for systemic errors in the
-measurements.
+measurements. These features are not currently supported by the lm85
+driver.
 
 In addition to the ADM1027 features, the ADT7463 also has Tmin control
 and THERM asserted counts. Automatic Tmin control acts to adjust the
diff --git a/Documentation/power/power_supply_class.txt b/Documentation/power/power_supply_class.txt
index a8686e5a6857..c6cd4956047c 100644
--- a/Documentation/power/power_supply_class.txt
+++ b/Documentation/power/power_supply_class.txt
@@ -101,6 +101,10 @@ of charge when battery became full/empty". It also could mean "value of
 charge when battery considered full/empty at given conditions (temperature,
 age)". I.e. these attributes represents real thresholds, not design values.
 
+CHARGE_COUNTER - the current charge counter (in µAh).  This could easily
+be negative; there is no empty or full value.  It is only useful for
+relative, time-based measurements.
+
 ENERGY_FULL, ENERGY_EMPTY - same as above but for energy.
 
 CAPACITY - capacity in percents.
diff --git a/Documentation/power/regulator/consumer.txt b/Documentation/power/regulator/consumer.txt
new file mode 100644
index 000000000000..82b7a43aadba
--- /dev/null
+++ b/Documentation/power/regulator/consumer.txt
@@ -0,0 +1,182 @@
+Regulator Consumer Driver Interface
+===================================
+
+This text describes the regulator interface for consumer device drivers.
+Please see overview.txt for a description of the terms used in this text.
+
+
+1. Consumer Regulator Access (static & dynamic drivers)
+=======================================================
+
+A consumer driver can get access to it's supply regulator by calling :-
+
+regulator = regulator_get(dev, "Vcc");
+
+The consumer passes in it's struct device pointer and power supply ID. The core
+then finds the correct regulator by consulting a machine specific lookup table.
+If the lookup is successful then this call will return a pointer to the struct
+regulator that supplies this consumer.
+
+To release the regulator the consumer driver should call :-
+
+regulator_put(regulator);
+
+Consumers can be supplied by more than one regulator e.g. codec consumer with
+analog and digital supplies :-
+
+digital = regulator_get(dev, "Vcc");  /* digital core */
+analog = regulator_get(dev, "Avdd");  /* analog */
+
+The regulator access functions regulator_get() and regulator_put() will
+usually be called in your device drivers probe() and remove() respectively.
+
+
+2. Regulator Output Enable & Disable (static & dynamic drivers)
+====================================================================
+
+A consumer can enable it's power supply by calling:-
+
+int regulator_enable(regulator);
+
+NOTE: The supply may already be enabled before regulator_enabled() is called.
+This may happen if the consumer shares the regulator or the regulator has been
+previously enabled by bootloader or kernel board initialization code.
+
+A consumer can determine if a regulator is enabled by calling :-
+
+int regulator_is_enabled(regulator);
+
+This will return > zero when the regulator is enabled.
+
+
+A consumer can disable it's supply when no longer needed by calling :-
+
+int regulator_disable(regulator);
+
+NOTE: This may not disable the supply if it's shared with other consumers. The
+regulator will only be disabled when the enabled reference count is zero.
+
+Finally, a regulator can be forcefully disabled in the case of an emergency :-
+
+int regulator_force_disable(regulator);
+
+NOTE: this will immediately and forcefully shutdown the regulator output. All
+consumers will be powered off.
+
+
+3. Regulator Voltage Control & Status (dynamic drivers)
+======================================================
+
+Some consumer drivers need to be able to dynamically change their supply
+voltage to match system operating points. e.g. CPUfreq drivers can scale
+voltage along with frequency to save power, SD drivers may need to select the
+correct card voltage, etc.
+
+Consumers can control their supply voltage by calling :-
+
+int regulator_set_voltage(regulator, min_uV, max_uV);
+
+Where min_uV and max_uV are the minimum and maximum acceptable voltages in
+microvolts.
+
+NOTE: this can be called when the regulator is enabled or disabled. If called
+when enabled, then the voltage changes instantly, otherwise the voltage
+configuration changes and the voltage is physically set when the regulator is
+next enabled.
+
+The regulators configured voltage output can be found by calling :-
+
+int regulator_get_voltage(regulator);
+
+NOTE: get_voltage() will return the configured output voltage whether the
+regulator is enabled or disabled and should NOT be used to determine regulator
+output state. However this can be used in conjunction with is_enabled() to
+determine the regulator physical output voltage.
+
+
+4. Regulator Current Limit Control & Status (dynamic drivers)
+===========================================================
+
+Some consumer drivers need to be able to dynamically change their supply
+current limit to match system operating points. e.g. LCD backlight driver can
+change the current limit to vary the backlight brightness, USB drivers may want
+to set the limit to 500mA when supplying power.
+
+Consumers can control their supply current limit by calling :-
+
+int regulator_set_current_limit(regulator, min_uV, max_uV);
+
+Where min_uA and max_uA are the minimum and maximum acceptable current limit in
+microamps.
+
+NOTE: this can be called when the regulator is enabled or disabled. If called
+when enabled, then the current limit changes instantly, otherwise the current
+limit configuration changes and the current limit is physically set when the
+regulator is next enabled.
+
+A regulators current limit can be found by calling :-
+
+int regulator_get_current_limit(regulator);
+
+NOTE: get_current_limit() will return the current limit whether the regulator
+is enabled or disabled and should not be used to determine regulator current
+load.
+
+
+5. Regulator Operating Mode Control & Status (dynamic drivers)
+=============================================================
+
+Some consumers can further save system power by changing the operating mode of
+their supply regulator to be more efficient when the consumers operating state
+changes. e.g. consumer driver is idle and subsequently draws less current
+
+Regulator operating mode can be changed indirectly or directly.
+
+Indirect operating mode control.
+--------------------------------
+Consumer drivers can request a change in their supply regulator operating mode
+by calling :-
+
+int regulator_set_optimum_mode(struct regulator *regulator, int load_uA);
+
+This will cause the core to recalculate the total load on the regulator (based
+on all it's consumers) and change operating mode (if necessary and permitted)
+to best match the current operating load.
+
+The load_uA value can be determined from the consumers datasheet. e.g.most
+datasheets have tables showing the max current consumed in certain situations.
+
+Most consumers will use indirect operating mode control since they have no
+knowledge of the regulator or whether the regulator is shared with other
+consumers.
+
+Direct operating mode control.
+------------------------------
+Bespoke or tightly coupled drivers may want to directly control regulator
+operating mode depending on their operating point. This can be achieved by
+calling :-
+
+int regulator_set_mode(struct regulator *regulator, unsigned int mode);
+unsigned int regulator_get_mode(struct regulator *regulator);
+
+Direct mode will only be used by consumers that *know* about the regulator and
+are not sharing the regulator with other consumers.
+
+
+6. Regulator Events
+===================
+Regulators can notify consumers of external events. Events could be received by
+consumers under regulator stress or failure conditions.
+
+Consumers can register interest in regulator events by calling :-
+
+int regulator_register_notifier(struct regulator *regulator,
+                              struct notifier_block *nb);
+
+Consumers can uregister interest by calling :-
+
+int regulator_unregister_notifier(struct regulator *regulator,
+                                struct notifier_block *nb);
+
+Regulators use the kernel notifier framework to send event to thier interested
+consumers.
diff --git a/Documentation/power/regulator/machine.txt b/Documentation/power/regulator/machine.txt
new file mode 100644
index 000000000000..c9a35665cf70
--- /dev/null
+++ b/Documentation/power/regulator/machine.txt
@@ -0,0 +1,101 @@
+Regulator Machine Driver Interface
+===================================
+
+The regulator machine driver interface is intended for board/machine specific
+initialisation code to configure the regulator subsystem. Typical things that
+machine drivers would do are :-
+
+ 1. Regulator -> Device mapping.
+ 2. Regulator supply configuration.
+ 3. Power Domain constraint setting.
+
+
+
+1. Regulator -> device mapping
+==============================
+Consider the following machine :-
+
+  Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+               |
+               +-> [Consumer B @ 3.3V]
+
+The drivers for consumers A & B must be mapped to the correct regulator in
+order to control their power supply. This mapping can be achieved in machine
+initialisation code by calling :-
+
+int regulator_set_device_supply(const char *regulator, struct device *dev,
+                                const char *supply);
+
+and is shown with the following code :-
+
+regulator_set_device_supply("Regulator-1", devB, "Vcc");
+regulator_set_device_supply("Regulator-2", devA, "Vcc");
+
+This maps Regulator-1 to the 'Vcc' supply for Consumer B and maps Regulator-2
+to the 'Vcc' supply for Consumer A.
+
+
+2. Regulator supply configuration.
+==================================
+Consider the following machine (again) :-
+
+  Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+               |
+               +-> [Consumer B @ 3.3V]
+
+Regulator-1 supplies power to Regulator-2. This relationship must be registered
+with the core so that Regulator-1 is also enabled when Consumer A enables it's
+supply (Regulator-2).
+
+This relationship can be register with the core via :-
+
+int regulator_set_supply(const char *regulator, const char *regulator_supply);
+
+In this example we would use the following code :-
+
+regulator_set_supply("Regulator-2", "Regulator-1");
+
+Relationships can be queried by calling :-
+
+const char *regulator_get_supply(const char *regulator);
+
+
+3. Power Domain constraint setting.
+===================================
+Each power domain within a system has physical constraints on voltage and
+current. This must be defined in software so that the power domain is always
+operated within specifications.
+
+Consider the following machine (again) :-
+
+  Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+               |
+               +-> [Consumer B @ 3.3V]
+
+This gives us two regulators and two power domains:
+
+                   Domain 1: Regulator-2, Consumer B.
+                   Domain 2: Consumer A.
+
+Constraints can be registered by calling :-
+
+int regulator_set_platform_constraints(const char *regulator,
+        struct regulation_constraints *constraints);
+
+The example is defined as follows :-
+
+struct regulation_constraints domain_1 = {
+        .min_uV = 3300000,
+        .max_uV = 3300000,
+        .valid_modes_mask = REGULATOR_MODE_NORMAL,
+};
+
+struct regulation_constraints domain_2 = {
+        .min_uV = 1800000,
+        .max_uV = 2000000,
+        .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+        .valid_modes_mask = REGULATOR_MODE_NORMAL,
+};
+
+regulator_set_platform_constraints("Regulator-1", &domain_1);
+regulator_set_platform_constraints("Regulator-2", &domain_2);
diff --git a/Documentation/power/regulator/overview.txt b/Documentation/power/regulator/overview.txt
new file mode 100644
index 000000000000..bdcb332bd7fb
--- /dev/null
+++ b/Documentation/power/regulator/overview.txt
@@ -0,0 +1,171 @@
+Linux voltage and current regulator framework
+=============================================
+
+About
+=====
+
+This framework is designed to provide a standard kernel interface to control
+voltage and current regulators.
+
+The intention is to allow systems to dynamically control regulator power output
+in order to save power and prolong battery life. This applies to both voltage
+regulators (where voltage output is controllable) and current sinks (where
+current limit is controllable).
+
+(C) 2008  Wolfson Microelectronics PLC.
+Author: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+
+
+Nomenclature
+============
+
+Some terms used in this document:-
+
+  o Regulator    - Electronic device that supplies power to other devices.
+                   Most regulators can enable and disable their output whilst
+                   some can control their output voltage and or current.
+
+                   Input Voltage -> Regulator -> Output Voltage
+
+
+  o PMIC         - Power Management IC. An IC that contains numerous regulators
+                   and often contains other susbsystems.
+
+
+  o Consumer     - Electronic device that is supplied power by a regulator.
+                   Consumers can be classified into two types:-
+
+                   Static: consumer does not change it's supply voltage or
+                   current limit. It only needs to enable or disable it's
+                   power supply. It's supply voltage is set by the hardware,
+                   bootloader, firmware or kernel board initialisation code.
+
+                   Dynamic: consumer needs to change it's supply voltage or
+                   current limit to meet operation demands.
+
+
+  o Power Domain - Electronic circuit that is supplied it's input power by the
+                   output power of a regulator, switch or by another power
+                   domain.
+
+                   The supply regulator may be behind a switch(s). i.e.
+
+                   Regulator -+-> Switch-1 -+-> Switch-2 --> [Consumer A]
+                              |             |
+                              |             +-> [Consumer B], [Consumer C]
+                              |
+                              +-> [Consumer D], [Consumer E]
+
+                   That is one regulator and three power domains:
+
+                   Domain 1: Switch-1, Consumers D & E.
+                   Domain 2: Switch-2, Consumers B & C.
+                   Domain 3: Consumer A.
+
+                   and this represents a "supplies" relationship:
+
+                   Domain-1 --> Domain-2 --> Domain-3.
+
+                   A power domain may have regulators that are supplied power
+                   by other regulators. i.e.
+
+                   Regulator-1 -+-> Regulator-2 -+-> [Consumer A]
+                                |
+                                +-> [Consumer B]
+
+                   This gives us two regulators and two power domains:
+
+                   Domain 1: Regulator-2, Consumer B.
+                   Domain 2: Consumer A.
+
+                   and a "supplies" relationship:
+
+                   Domain-1 --> Domain-2
+
+
+  o Constraints  - Constraints are used to define power levels for performance
+                   and hardware protection. Constraints exist at three levels:
+
+                   Regulator Level: This is defined by the regulator hardware
+                   operating parameters and is specified in the regulator
+                   datasheet. i.e.
+
+                     - voltage output is in the range 800mV -> 3500mV.
+                     - regulator current output limit is 20mA @ 5V but is
+                       10mA @ 10V.
+
+                   Power Domain Level: This is defined in software by kernel
+                   level board initialisation code. It is used to constrain a
+                   power domain to a particular power range. i.e.
+
+                     - Domain-1 voltage is 3300mV
+                     - Domain-2 voltage is 1400mV -> 1600mV
+                     - Domain-3 current limit is 0mA -> 20mA.
+
+                   Consumer Level: This is defined by consumer drivers
+                   dynamically setting voltage or current limit levels.
+
+                   e.g. a consumer backlight driver asks for a current increase
+                   from 5mA to 10mA to increase LCD illumination. This passes
+                   to through the levels as follows :-
+
+                   Consumer: need to increase LCD brightness. Lookup and
+                   request next current mA value in brightness table (the
+                   consumer driver could be used on several different
+                   personalities based upon the same reference device).
+
+                   Power Domain: is the new current limit within the domain
+                   operating limits for this domain and system state (e.g.
+                   battery power, USB power)
+
+                   Regulator Domains: is the new current limit within the
+                   regulator operating parameters for input/ouput voltage.
+
+                   If the regulator request passes all the constraint tests
+                   then the new regulator value is applied.
+
+
+Design
+======
+
+The framework is designed and targeted at SoC based devices but may also be
+relevant to non SoC devices and is split into the following four interfaces:-
+
+
+   1. Consumer driver interface.
+
+      This uses a similar API to the kernel clock interface in that consumer
+      drivers can get and put a regulator (like they can with clocks atm) and
+      get/set voltage, current limit, mode, enable and disable. This should
+      allow consumers complete control over their supply voltage and current
+      limit. This also compiles out if not in use so drivers can be reused in
+      systems with no regulator based power control.
+
+        See Documentation/power/regulator/consumer.txt
+
+   2. Regulator driver interface.
+
+      This allows regulator drivers to register their regulators and provide
+      operations to the core. It also has a notifier call chain for propagating
+      regulator events to clients.
+
+        See Documentation/power/regulator/regulator.txt
+
+   3. Machine interface.
+
+      This interface is for machine specific code and allows the creation of
+      voltage/current domains (with constraints) for each regulator. It can
+      provide regulator constraints that will prevent device damage through
+      overvoltage or over current caused by buggy client drivers. It also
+      allows the creation of a regulator tree whereby some regulators are
+      supplied by others (similar to a clock tree).
+
+        See Documentation/power/regulator/machine.txt
+
+   4. Userspace ABI.
+
+      The framework also exports a lot of useful voltage/current/opmode data to
+      userspace via sysfs. This could be used to help monitor device power
+      consumption and status.
+
+        See Documentation/ABI/testing/regulator-sysfs.txt
diff --git a/Documentation/power/regulator/regulator.txt b/Documentation/power/regulator/regulator.txt
new file mode 100644
index 000000000000..a69050143592
--- /dev/null
+++ b/Documentation/power/regulator/regulator.txt
@@ -0,0 +1,30 @@
+Regulator Driver Interface
+==========================
+
+The regulator driver interface is relatively simple and designed to allow
+regulator drivers to register their services with the core framework.
+
+
+Registration
+============
+
+Drivers can register a regulator by calling :-
+
+struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc,
+                                          void *reg_data);
+
+This will register the regulators capabilities and operations the regulator
+core. The core does not touch reg_data (private to regulator driver).
+
+Regulators can be unregistered by calling :-
+
+void regulator_unregister(struct regulator_dev *rdev);
+
+
+Regulator Events
+================
+Regulators can send events (e.g. over temp, under voltage, etc) to consumer
+drivers by calling :-
+
+int regulator_notifier_call_chain(struct regulator_dev *rdev,
+                                  unsigned long event, void *data);
diff --git a/Documentation/powerpc/00-INDEX b/Documentation/powerpc/00-INDEX
index 3be84aa38dfe..29d839ce7327 100644
--- a/Documentation/powerpc/00-INDEX
+++ b/Documentation/powerpc/00-INDEX
@@ -20,8 +20,6 @@ mpc52xx-device-tree-bindings.txt
         - MPC5200 Device Tree Bindings
 ppc_htab.txt
         - info about the Linux/PPC /proc/ppc_htab entry
-SBC8260_memory_mapping.txt
-        - EST SBC8260 board info
 smp.txt
         - use and state info about Linux/PPC on MP machines
 sound.txt
diff --git a/Documentation/powerpc/SBC8260_memory_mapping.txt b/Documentation/powerpc/SBC8260_memory_mapping.txt
deleted file mode 100644
index e6e9ee0506c3..000000000000
--- a/Documentation/powerpc/SBC8260_memory_mapping.txt
+++ /dev/null
@@ -1,197 +0,0 @@
-Please mail me (Jon Diekema, diekema_jon@si.com or diekema@cideas.com)
-if you have questions, comments or corrections.
-
-        * EST SBC8260 Linux memory mapping rules
-
-        http://www.estc.com/ 
-        http://www.estc.com/products/boards/SBC8260-8240_ds.html
-
-        Initial conditions:
-        -------------------
-        
-        Tasks that need to be perform by the boot ROM before control is
-        transferred to zImage (compressed Linux kernel):
-
-        - Define the IMMR to 0xf0000000
-
-        - Initialize the memory controller so that RAM is available at
-          physical address 0x00000000.  On the SBC8260 is this 16M (64M)
-          SDRAM.
-
-        - The boot ROM should only clear the RAM that it is using.
-
-          The reason for doing this is to enhances the chances of a
-          successful post mortem on a Linux panic.  One of the first
-          items to examine is the 16k (LOG_BUF_LEN) circular console
-          buffer called log_buf which is defined in kernel/printk.c.
-
-        - To enhance boot ROM performance, the I-cache can be enabled.
-
-          Date: Mon, 22 May 2000 14:21:10 -0700
-          From: Neil Russell <caret@c-side.com>
-
-          LiMon (LInux MONitor) runs with and starts Linux with MMU
-          off, I-cache enabled, D-cache disabled.  The I-cache doesn't
-          need hints from the MMU to work correctly as the D-cache
-          does.  No D-cache means no special code to handle devices in
-          the presence of cache (no snooping, etc). The use of the
-          I-cache means that the monitor can run acceptably fast
-          directly from ROM, rather than having to copy it to RAM.
-
-        - Build the board information structure (see 
-          include/asm-ppc/est8260.h for its definition)
-
-        - The compressed Linux kernel (zImage) contains a bootstrap loader 
-          that is position independent; you can load it into any RAM, 
-          ROM or FLASH memory address >= 0x00500000 (above 5 MB), or
-          at its link address of 0x00400000 (4 MB).
-
-          Note: If zImage is loaded at its link address of 0x00400000 (4 MB),
-                then zImage will skip the step of moving itself to 
-                its link address.
-
-        - Load R3 with the address of the board information structure
-
-        - Transfer control to zImage
-
-        - The Linux console port is SMC1, and the baud rate is controlled
-          from the bi_baudrate field of the board information structure.
-          On thing to keep in mind when picking the baud rate, is that
-          there is no flow control on the SMC ports.  I would stick
-          with something safe and standard like 19200.
-
-          On the EST SBC8260, the SMC1 port is on the COM1 connector of
-          the board.
-
-        
-        EST SBC8260 defaults:
-        ---------------------
-
-                                Chip
-        Memory                  Sel  Bus   Use
-        ---------------------   ---  ---   ----------------------------------
-        0x00000000-0x03FFFFFF   CS2  60x   (16M or 64M)/64M SDRAM
-        0x04000000-0x04FFFFFF   CS4  local  4M/16M SDRAM (soldered to the board)
-        0x21000000-0x21000000   CS7  60x    1B/64K Flash present detect (from the flash SIMM)
-        0x21000001-0x21000001   CS7  60x    1B/64K Switches (read) and LEDs (write)
-        0x22000000-0x2200FFFF   CS5  60x    8K/64K EEPROM
-        0xFC000000-0xFCFFFFFF   CS6  60x    2M/16M flash (8 bits wide, soldered to the board)
-        0xFE000000-0xFFFFFFFF   CS0  60x    4M/16M flash (SIMM)
-
-        Notes:
-        ------
-
-        - The chip selects can map 32K blocks and up (powers of 2)
-
-        - The SDRAM machine can handled up to 128Mbytes per chip select
-
-        - Linux uses the 60x bus memory (the SDRAM DIMM) for the 
-          communications buffers.
-
-        - BATs can map 128K-256Mbytes each.  There are four data BATs and
-          four instruction BATs.  Generally the data and instruction BATs
-          are mapped the same.
-
-        - The IMMR must be set above the kernel virtual memory addresses,
-          which start at 0xC0000000.  Otherwise, the kernel may crash as
-          soon as you start any threads or processes due to VM collisions 
-          in the kernel or user process space.
-
-
-          Details from Dan Malek <dan_malek@mvista.com> on 10/29/1999:
-
-          The user application virtual space consumes the first 2 Gbytes
-          (0x00000000 to 0x7FFFFFFF).  The kernel virtual text starts at
-          0xC0000000, with data following.  There is a "protection hole"
-          between the end of kernel data and the start of the kernel
-          dynamically allocated space, but this space is still within
-          0xCxxxxxxx.
-
-          Obviously the kernel can't map any physical addresses 1:1 in
-          these ranges.
-
-
-          Details from Dan Malek <dan_malek@mvista.com> on 5/19/2000:
-
-          During the early kernel initialization, the kernel virtual
-          memory allocator is not operational.  Prior to this KVM
-          initialization, we choose to map virtual to physical addresses
-          1:1.  That is, the kernel virtual address exactly matches the
-          physical address on the bus.  These mappings are typically done
-          in arch/ppc/kernel/head.S, or arch/ppc/mm/init.c.  Only
-          absolutely necessary mappings should be done at this time, for
-          example board control registers or a serial uart.  Normal device
-          driver initialization should map resources later when necessary.
-
-          Although platform dependent, and certainly the case for embedded
-          8xx, traditionally memory is mapped at physical address zero,
-          and I/O devices above physical address 0x80000000.  The lowest
-          and highest (above 0xf0000000) I/O addresses are traditionally 
-          used for devices or registers we need to map during kernel 
-          initialization and prior to KVM operation.  For this reason, 
-          and since it followed prior PowerPC platform examples, I chose 
-          to map the embedded 8xx kernel to the 0xc0000000 virtual address.
-          This way, we can enable the MMU to map the kernel for proper 
-          operation, and still map a few windows before the KVM is operational.
-
-          On some systems, you could possibly run the kernel at the 
-          0x80000000 or any other virtual address.  It just depends upon 
-          mapping that must be done prior to KVM operational.  You can never 
-          map devices or kernel spaces that overlap with the user virtual 
-          space.  This is why default IMMR mapping used by most BDM tools 
-          won't work.  They put the IMMR at something like 0x10000000 or 
-          0x02000000 for example.  You simply can't map these addresses early
-          in the kernel, and continue proper system operation.
-
-          The embedded 8xx/82xx kernel is mature enough that all you should 
-          need to do is map the IMMR someplace at or above 0xf0000000 and it 
-          should boot far enough to get serial console messages and KGDB 
-          connected on any platform.  There are lots of other subtle memory 
-          management design features that you simply don't need to worry 
-          about.  If you are changing functions related to MMU initialization,
-          you are likely breaking things that are known to work and are 
-          heading down a path of disaster and frustration.  Your changes 
-          should be to make the flexibility of the processor fit Linux, 
-          not force arbitrary and non-workable memory mappings into Linux.
-
-        - You don't want to change KERNELLOAD or KERNELBASE, otherwise the
-          virtual memory and MMU code will get confused.
-        
-          arch/ppc/Makefile:KERNELLOAD = 0xc0000000
-
-          include/asm-ppc/page.h:#define PAGE_OFFSET    0xc0000000
-          include/asm-ppc/page.h:#define KERNELBASE     PAGE_OFFSET
-
-        - RAM is at physical address 0x00000000, and gets mapped to 
-          virtual address 0xC0000000 for the kernel.
-
-
-        Physical addresses used by the Linux kernel:
-        --------------------------------------------
-
-        0x00000000-0x3FFFFFFF   1GB reserved for RAM
-        0xF0000000-0xF001FFFF   128K IMMR  64K used for dual port memory,
-                                 64K for 8260 registers
-
-        
-        Logical addresses used by the Linux kernel:
-        -------------------------------------------
-
-        0xF0000000-0xFFFFFFFF   256M BAT0 (IMMR: dual port RAM, registers)
-        0xE0000000-0xEFFFFFFF   256M BAT1 (I/O space for custom boards)
-        0xC0000000-0xCFFFFFFF   256M BAT2 (RAM)
-        0xD0000000-0xDFFFFFFF   256M BAT3 (if RAM > 256MByte)
-
-
-        EST SBC8260 Linux mapping:
-        --------------------------
-
-        DBAT0, IBAT0, cache inhibited:
-
-                                Chip
-        Memory                  Sel  Use
-        ---------------------   ---  ---------------------------------
-        0xF0000000-0xF001FFFF   n/a  IMMR: dual port RAM, registers
-
-        DBAT1, IBAT1, cache inhibited:
-
diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
index b35f3482e3e4..2ea76d9d137c 100644
--- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/serial.txt
@@ -7,6 +7,15 @@ Currently defined compatibles:
 - fsl,cpm2-scc-uart
 - fsl,qe-uart
 
+Modem control lines connected to GPIO controllers are listed in the gpios
+property as described in booting-without-of.txt, section IX.1 in the following
+order:
+
+CTS, RTS, DCD, DSR, DTR, and RI.
+
+The gpios property is optional and can be left out when control lines are
+not used.
+
 Example:
 
         serial@11a00 {
@@ -18,4 +27,6 @@ Example:
                 interrupt-parent = <&PIC>;
                 fsl,cpm-brg = <1>;
                 fsl,cpm-command = <00800000>;
+                gpios = <&gpio_c 15 0
+                         &gpio_d 29 0>;
         };
diff --git a/Documentation/rfkill.txt b/Documentation/rfkill.txt
index 0843ed0163a5..28b6ec87c642 100644
--- a/Documentation/rfkill.txt
+++ b/Documentation/rfkill.txt
@@ -390,9 +390,10 @@ rfkill lines are inactive, it must return RFKILL_STATE_SOFT_BLOCKED if its soft
 rfkill input line is active.  Only if none of the rfkill input lines are
 active, will it return RFKILL_STATE_UNBLOCKED.
 
-If it doesn't implement the get_state() hook, it must make sure that its calls
-to rfkill_force_state() are enough to keep the status always up-to-date, and it
-must do a rfkill_force_state() on resume from sleep.
+Since the device has a hardware rfkill line, it IS subject to state changes
+external to rfkill.  Therefore, the driver must make sure that it calls
+rfkill_force_state() to keep the status always up-to-date, and it must do a
+rfkill_force_state() on resume from sleep.
 
 Every time the driver gets a notification from the card that one of its rfkill
 lines changed state (polling might be needed on badly designed cards that don't
@@ -422,13 +423,24 @@ of the hardware is unknown), or read-write (where the hardware can be queried
 about its current state).
 
 The rfkill class will call the get_state hook of a device every time it needs
-to know the *real* current state of the hardware.  This can happen often.
+to know the *real* current state of the hardware.  This can happen often, but
+it does not do any polling, so it is not enough on hardware that is subject
+to state changes outside of the rfkill subsystem.
+
+Therefore, calling rfkill_force_state() when a state change happens is
+mandatory when the device has a hardware rfkill line, or when something else
+like the firmware could cause its state to be changed without going through the
+rfkill class.
 
 Some hardware provides events when its status changes.  In these cases, it is
 best for the driver to not provide a get_state hook, and instead register the
 rfkill class *already* with the correct status, and keep it updated using
 rfkill_force_state() when it gets an event from the hardware.
 
+rfkill_force_state() must be used on the device resume handlers to update the
+rfkill status, should there be any chance of the device status changing during
+the sleep.
+
 There is no provision for a statically-allocated rfkill struct.  You must
 use rfkill_allocate() to allocate one.