2 files changed, 165 insertions, 1 deletions

diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt
index 8cf17fe43003..945de361022f 100644
--- a/Documentation/sound/alsa/ALSA-Configuration.txt
+++ b/Documentation/sound/alsa/ALSA-Configuration.txt
@@ -944,6 +944,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
                         * Onkyo SE-90PCI
                         * Onkyo SE-200PCI
                         * ESI Juli@
+                        * ESI Maya44
                         * Hercules Fortissimo IV
                         * EGO-SYS WaveTerminal 192M
 
@@ -952,7 +953,7 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
                   prodigy71xt, prodigy71hifi, prodigyhd2, prodigy192,
                   juli, aureon51, aureon71, universe, ap192, k8x800,
                   phase22, phase28, ms300, av710, se200pci, se90pci,
-                  fortissimo4, sn25p, WT192M
+                  fortissimo4, sn25p, WT192M, maya44
 
     This module supports multiple cards and autoprobe.
 
diff --git a/Documentation/sound/alsa/README.maya44 b/Documentation/sound/alsa/README.maya44
new file mode 100644
index 000000000000..0e41576fa13e
--- /dev/null
+++ b/Documentation/sound/alsa/README.maya44
@@ -0,0 +1,163 @@
+NOTE: The following is the original document of Rainer's patch that the
+current maya44 code based on.  Some contents might be obsoleted, but I
+keep here as reference -- tiwai
+
+----------------------------------------------------------------
+ 
+STATE OF DEVELOPMENT:
+
+This driver is being developed on the initiative of Piotr Makowski (oponek@gmail.com) and financed by Lars Bergmann.
+Development is carried out by Rainer Zimmermann (mail@lightshed.de).
+
+ESI provided a sample Maya44 card for the development work.
+
+However, unfortunately it has turned out difficult to get detailed programming information, so I (Rainer Zimmermann) had to find out some card-specific information by experiment and conjecture. Some information (in particular, several GPIO bits) is still missing.
+
+This is the first testing version of the Maya44 driver released to the alsa-devel mailing list (Feb 5, 2008).
+
+
+The following functions work, as tested by Rainer Zimmermann and Piotr Makowski:
+
+- playback and capture at all sampling rates
+- input/output level
+- crossmixing
+- line/mic switch
+- phantom power switch
+- analogue monitor a.k.a bypass
+
+
+The following functions *should* work, but are not fully tested:
+
+- Channel 3+4 analogue - S/PDIF input switching
+- S/PDIF output
+- all inputs/outputs on the M/IO/DIO extension card
+- internal/external clock selection
+
+
+*In particular, we would appreciate testing of these functions by anyone who has access to an M/IO/DIO extension card.*
+
+
+Things that do not seem to work:
+
+- The level meters ("multi track") in 'alsamixer' do not seem to react to signals in (if this is a bug, it would probably be in the existing ICE1724 code).
+
+- Ardour 2.1 seems to work only via JACK, not using ALSA directly or via OSS. This still needs to be tracked down.
+
+
+DRIVER DETAILS:
+
+the following files were added:
+
+pci/ice1724/maya44.c        - Maya44 specific code
+pci/ice1724/maya44.h
+pci/ice1724/ice1724.patch
+pci/ice1724/ice1724.h.patch - PROPOSED patch to ice1724.h (see SAMPLING RATES)
+i2c/other/wm8776.c  - low-level access routines for Wolfson WM8776 codecs 
+include/wm8776.h
+
+
+Note that the wm8776.c code is meant to be card-independent and does not actually register the codec with the ALSA infrastructure.
+This is done in maya44.c, mainly because some of the WM8776 controls are used in Maya44-specific ways, and should be named appropriately.
+
+
+the following files were created in pci/ice1724, simply #including the corresponding file from the alsa-kernel tree:
+
+wtm.h
+vt1720_mobo.h
+revo.h
+prodigy192.h
+pontis.h
+phase.h
+maya44.h
+juli.h
+aureon.h
+amp.h
+envy24ht.h
+se.h
+prodigy_hifi.h
+
+
+*I hope this is the correct way to do things.*
+
+
+SAMPLING RATES:
+
+The Maya44 card (or more exactly, the Wolfson WM8776 codecs) allow a maximum sampling rate of 192 kHz for playback and 92 kHz for capture.
+
+As the ICE1724 chip only allows one global sampling rate, this is handled as follows:
+
+* setting the sampling rate on any open PCM device on the maya44 card will always set the *global* sampling rate for all playback and capture channels.
+
+* In the current state of the driver, setting rates of up to 192 kHz is permitted even for capture devices.
+
+*AVOID CAPTURING AT RATES ABOVE 96kHz*, even though it may appear to work. The codec cannot actually capture at such rates, meaning poor quality.
+
+
+I propose some additional code for limiting the sampling rate when setting on a capture pcm device. However because of the global sampling rate, this logic would be somewhat problematic.
+
+The proposed code (currently deactivated) is in ice1712.h.patch, ice1724.c and maya44.c (in pci/ice1712).
+
+
+SOUND DEVICES:
+
+PCM devices correspond to inputs/outputs as follows (assuming Maya44 is card #0):
+
+hw:0,0 input - stereo, analog input 1+2
+hw:0,0 output - stereo, analog output 1+2
+hw:0,1 input - stereo, analog input 3+4 OR S/PDIF input
+hw:0,1 output - stereo, analog output 3+4 (and SPDIF out)
+
+
+NAMING OF MIXER CONTROLS:
+
+(for more information about the signal flow, please refer to the block diagram on p.24 of the ESI Maya44 manual, or in the ESI windows software).
+
+
+PCM: (digital) output level for channel 1+2
+PCM 1: same for channel 3+4
+
+Mic Phantom+48V: switch for +48V phantom power for electrostatic microphones on input 1/2.
+    Make sure this is not turned on while any other source is connected to input 1/2.
+    It might damage the source and/or the maya44 card.
+
+Mic/Line input: if switch is is on, input jack 1/2 is microphone input (mono), otherwise line input (stereo).
+
+Bypass: analogue bypass from ADC input to output for channel 1+2. Same as "Monitor" in the windows driver.
+Bypass 1: same for channel 3+4.
+
+Crossmix: cross-mixer from channels 1+2 to channels 3+4
+Crossmix 1: cross-mixer from channels 3+4 to channels 1+2
+
+IEC958 Output: switch for S/PDIF output.
+    This is not supported by the ESI windows driver.
+    S/PDIF should output the same signal as channel 3+4. [untested!]
+
+
+Digitial output selectors:
+
+    These switches allow a direct digital routing from the ADCs to the DACs.
+    Each switch determines where the digital input data to one of the DACs comes from.
+    They are not supported by the ESI windows driver.
+    For normal operation, they should all be set to "PCM out".
+
+H/W: Output source channel 1
+H/W 1: Output source channel 2
+H/W 2: Output source channel 3
+H/W 3: Output source channel 4
+
+H/W 4 ... H/W 9: unknown function, left in to enable testing.
+    Possibly some of these control S/PDIF output(s).
+    If these turn out to be unused, they will go away in later driver versions.
+
+Selectable values for each of the digital output selectors are:
+   "PCM out" -> DAC output of the corresponding channel (default setting)
+   "Input 1"...
+   "Input 4" -> direct routing from ADC output of the selected input channel
+
+
+--------
+
+Feb 14, 2008
+Rainer Zimmermann
+mail@lightshed.de
+