3 files changed, 41 insertions, 1 deletions

diff --git a/Documentation/powerpc/dts-bindings/fsl/board.txt b/Documentation/powerpc/dts-bindings/fsl/board.txt
index e8b5bc24d0ac..39e941515a36 100644
--- a/Documentation/powerpc/dts-bindings/fsl/board.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/board.txt
@@ -20,12 +20,16 @@ Required properities:
 - compatible : should be "fsl,fpga-pixis".
 - reg : should contain the address and the length of the FPPGA register
   set.
+- interrupt-parent: should specify phandle for the interrupt controller.
+- interrupts : should specify event (wakeup) IRQ.
 
 Example (MPC8610HPCD):
 
         board-control@e8000000 {
                 compatible = "fsl,fpga-pixis";
                 reg = <0xe8000000 32>;
+                interrupt-parent = <&mpic>;
+                interrupts = <8 8>;
         };
 
 * Freescale BCSR GPIO banks
diff --git a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
index 8447fd7090d0..5c6602dbfdc2 100644
--- a/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/mpc5200.txt
@@ -103,7 +103,22 @@ fsl,mpc5200-gpt nodes
 ---------------------
 On the mpc5200 and 5200b, GPT0 has a watchdog timer function.  If the board
 design supports the internal wdt, then the device node for GPT0 should
-include the empty property 'fsl,has-wdt'.
+include the empty property 'fsl,has-wdt'.  Note that this does not activate
+the watchdog.  The timer will function as a GPT if the timer api is used, and
+it will function as watchdog if the watchdog device is used.  The watchdog
+mode has priority over the gpt mode, i.e. if the watchdog is activated, any
+gpt api call to this timer will fail with -EBUSY.
+
+If you add the property
+        fsl,wdt-on-boot = <n>;
+GPT0 will be marked as in-use watchdog, i.e. blocking every gpt access to it.
+If n>0, the watchdog is started with a timeout of n seconds.  If n=0, the
+configuration of the watchdog is not touched.  This is useful in two cases:
+- just mark GPT0 as watchdog, blocking gpt accesses, and configure it later;
+- do not touch a configuration assigned by the boot loader which supervises
+  the boot process itself.
+
+The watchdog will respect the CONFIG_WATCHDOG_NOWAYOUT option.
 
 An mpc5200-gpt can be used as a single line GPIO controller.  To do so,
 add the following properties to the gpt node:
@@ -178,3 +193,13 @@ External interrupts:
         external irq3:  interrupts = <1 3 n>;
 'n' is sense (0: level high, 1: edge rising, 2: edge falling 3: level low)
 
+fsl,mpc5200-mscan nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properites, you can
+also specify which clock source shall be used for the controller:
+
+- fsl,mscan-clock-source- a string describing the clock source. Valid values
+                          are:  "ip" for ip bus clock
+                                "ref" for reference clock (XTAL)
+                          "ref" is default in case this property is not
+                          present.
diff --git a/Documentation/powerpc/dts-bindings/xilinx.txt b/Documentation/powerpc/dts-bindings/xilinx.txt
index 80339fe4300b..ea68046bb9cb 100644
--- a/Documentation/powerpc/dts-bindings/xilinx.txt
+++ b/Documentation/powerpc/dts-bindings/xilinx.txt
@@ -292,4 +292,15 @@
        - reg-offset : A value of 3 is required
        - reg-shift : A value of 2 is required
 
+      vii) Xilinx USB Host controller
+
+      The Xilinx USB host controller is EHCI compatible but with a different
+      base address for the EHCI registers, and it is always a big-endian
+      USB Host controller. The hardware can be configured as high speed only,
+      or high speed/full speed hybrid.
+
+      Required properties:
+      - xlnx,support-usb-fs: A value 0 means the core is built as high speed
+                             only. A value 1 means the core also supports
+                             full speed devices.