2 files changed, 111 insertions, 15 deletions

diff --git a/Documentation/powerpc/dts-bindings/fsl/i2c.txt b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
index d0ab33e21fe6..b6d2e21474f9 100644
--- a/Documentation/powerpc/dts-bindings/fsl/i2c.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/i2c.txt
@@ -7,8 +7,10 @@ Required properties :
 
 Recommended properties :
 
- - compatible : Should be "fsl-i2c" for parts compatible with
-   Freescale I2C specifications.
+ - compatible : compatibility list with 2 entries, the first should
+   be "fsl,CHIP-i2c" where CHIP is the name of a compatible processor,
+   e.g. mpc8313, mpc8543, mpc8544, mpc5200 or mpc5200b. The second one
+   should be "fsl-i2c".
  - interrupts : <a b> where a is the interrupt number and b is a
    field that represents an encoding of the sense and level
    information for the interrupt.  This should be encoded based on
@@ -16,17 +18,31 @@ Recommended properties :
    controller you have.
  - interrupt-parent : the phandle for the interrupt controller that
    services interrupts for this device.
- - dfsrr : boolean; if defined, indicates that this I2C device has
-   a digital filter sampling rate register
- - fsl5200-clocking : boolean; if defined, indicated that this device
-   uses the FSL 5200 clocking mechanism.
-
-Example :
-        i2c@3000 {
-                interrupt-parent = <40000>;
-                interrupts = <1b 3>;
-                reg = <3000 18>;
-                device_type = "i2c";
-                compatible  = "fsl-i2c";
-                dfsrr;
+ - fsl,preserve-clocking : boolean; if defined, the clock settings
+   from the bootloader are preserved (not touched).
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Examples :
+
+        i2c@3d00 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+                cell-index = <0>;
+                reg = <0x3d00 0x40>;
+                interrupts = <2 15 0>;
+                interrupt-parent = <&mpc5200_pic>;
+                fsl,preserve-clocking;
         };
+
+        i2c@3100 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                cell-index = <1>;
+                compatible = "fsl,mpc8544-i2c", "fsl-i2c";
+                reg = <0x3100 0x100>;
+                interrupts = <43 2>;
+                interrupt-parent = <&mpic>;
+                clock-frequency = <400000>;
+        };
+
diff --git a/Documentation/powerpc/dts-bindings/mtd-physmap.txt b/Documentation/powerpc/dts-bindings/mtd-physmap.txt
new file mode 100644
index 000000000000..667c9bde8699
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/mtd-physmap.txt
@@ -0,0 +1,80 @@
+CFI or JEDEC memory-mapped NOR flash
+
+Flash chips (Memory Technology Devices) are often used for solid state
+file systems on embedded devices.
+
+ - compatible : should contain the specific model of flash chip(s)
+   used, if known, followed by either "cfi-flash" or "jedec-flash"
+ - reg : Address range(s) of the flash chip(s)
+   It's possible to (optionally) define multiple "reg" tuples so that
+   non-identical NOR chips can be described in one flash node.
+ - bank-width : Width (in bytes) of the flash bank.  Equal to the
+   device width times the number of interleaved chips.
+ - device-width : (optional) Width of a single flash chip.  If
+   omitted, assumed to be equal to 'bank-width'.
+ - #address-cells, #size-cells : Must be present if the flash has
+   sub-nodes representing partitions (see below).  In this case
+   both #address-cells and #size-cells must be equal to 1.
+
+For JEDEC compatible devices, the following additional properties
+are defined:
+
+ - vendor-id : Contains the flash chip's vendor id (1 byte).
+ - device-id : Contains the flash chip's device id (1 byte).
+
+In addition to the information on the flash bank itself, the
+device tree may optionally contain additional information
+describing partitions of the flash address space.  This can be
+used on platforms which have strong conventions about which
+portions of the flash are used for what purposes, but which don't
+use an on-flash partition table such as RedBoot.
+
+Each partition is represented as a sub-node of the flash device.
+Each node's name represents the name of the corresponding
+partition of the flash device.
+
+Flash partitions
+ - reg : The partition's offset and size within the flash bank.
+ - label : (optional) The label / name for this flash partition.
+   If omitted, the label is taken from the node name (excluding
+   the unit address).
+ - read-only : (optional) This parameter, if present, is a hint to
+   Linux that this flash partition should only be mounted
+   read-only.  This is usually used for flash partitions
+   containing early-boot firmware images or data which should not
+   be clobbered.
+
+Example:
+
+        flash@ff000000 {
+                compatible = "amd,am29lv128ml", "cfi-flash";
+                reg = <ff000000 01000000>;
+                bank-width = <4>;
+                device-width = <1>;
+                #address-cells = <1>;
+                #size-cells = <1>;
+                fs@0 {
+                        label = "fs";
+                        reg = <0 f80000>;
+                };
+                firmware@f80000 {
+                        label ="firmware";
+                        reg = <f80000 80000>;
+                        read-only;
+                };
+        };
+
+Here an example with multiple "reg" tuples:
+
+        flash@f0000000,0 {
+                #address-cells = <1>;
+                #size-cells = <1>;
+                compatible = "intel,PC48F4400P0VB", "cfi-flash";
+                reg = <0 0x00000000 0x02000000
+                       0 0x02000000 0x02000000>;
+                bank-width = <2>;
+                partition@0 {
+                        label = "test-part1";
+                        reg = <0 0x04000000>;
+                };
+        };