1 files changed, 22 insertions, 7 deletions

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 0fa3c0545994..0122e5f810fb 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -44,6 +44,7 @@ parameter is applicable:
         FB      The frame buffer device is enabled.
         HW      Appropriate hardware is enabled.
         IA-64   IA-64 architecture is enabled.
+        IMA     Integrity measurement architecture is enabled.
         IOSCHED More than one I/O scheduler is enabled.
         IP_PNP  IP DHCP, BOOTP, or RARP is enabled.
         ISAPNP  ISA PnP code is enabled.
@@ -502,10 +503,12 @@ and is between 256 and 4096 characters. It is defined in the file
                         architectural default is too low.
 
         hpet=           [X86-32,HPET] option to control HPET usage
-                        Format: { enable (default) | disable | force }
+                        Format: { enable (default) | disable | force |
+                                verbose }
                         disable: disable HPET and use PIT instead
                         force: allow force enabled of undocumented chips (ICH4,
                         VIA, nVidia)
+                        verbose: show contents of HPET registers during setup
 
         com20020=       [HW,NET] ARCnet - COM20020 chipset
                         Format:
@@ -839,6 +842,9 @@ and is between 256 and 4096 characters. It is defined in the file
 
         hvc_iucv=       [S390] Number of z/VM IUCV hypervisor console (HVC)
                                terminal devices. Valid values: 0..8
+        hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs.
+                               If specified, z/VM IUCV HVC accepts connections
+                               from listed z/VM user IDs only.
 
         i8042.debug     [HW] Toggle i8042 debug mode
         i8042.direct    [HW] Put keyboard port into non-translated mode
@@ -912,6 +918,15 @@ and is between 256 and 4096 characters. It is defined in the file
         ihash_entries=  [KNL]
                         Set number of hash buckets for inode cache.
 
+        ima_audit=      [IMA]
+                        Format: { "0" | "1" }
+                        0 -- integrity auditing messages. (Default)
+                        1 -- enable informational integrity auditing messages.
+
+        ima_hash=       [IMA]
+                        Formt: { "sha1" | "md5" }
+                        default: "sha1"
+
         in2000=         [HW,SCSI]
                         See header of drivers/scsi/in2000.c.
 
@@ -1320,8 +1335,13 @@ and is between 256 and 4096 characters. It is defined in the file
 
         memtest=        [KNL,X86] Enable memtest
                         Format: <integer>
-                        range: 0,4 : pattern number
                         default : 0 <disable>
+                        Specifies the number of memtest passes to be
+                        performed. Each pass selects another test
+                        pattern from a given set of patterns. Memtest
+                        fills the memory with this pattern, validates
+                        memory contents and reserves bad memory
+                        regions that are detected.
 
         meye.*=         [HW] Set MotionEye Camera parameters
                         See Documentation/video4linux/meye.txt.
@@ -1826,11 +1846,6 @@ and is between 256 and 4096 characters. It is defined in the file
                         autoconfiguration.
                         Ranges are in pairs (memory base and size).
 
-        dynamic_printk  Enables pr_debug()/dev_dbg() calls if
-                        CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
-                        These can also be switched on/off via
-                        <debugfs>/dynamic_printk/modules
-
         print-fatal-signals=
                         [KNL] debug: print fatal signals
                         print-fatal-signals=1: print segfault info to