1 files changed, 91 insertions, 24 deletions

diff --git a/Documentation/input/xpad.txt b/Documentation/input/xpad.txt
index b9111a703ce0..5427bdf225ed 100644
--- a/Documentation/input/xpad.txt
+++ b/Documentation/input/xpad.txt
@@ -3,20 +3,37 @@ xpad - Linux USB driver for X-Box gamepads
 This is the very first release of a driver for X-Box gamepads.
 Basically, this was hacked away in just a few hours, so don't expect
 miracles.
+
 In particular, there is currently NO support for the rumble pack.
 You won't find many ff-aware linux applications anyway.
 
 
-0. Status
----------
+0. Notes
+--------
+
+Driver updated for kernel 2.6.17.11. (Based on a patch for 2.6.11.4.)
 
-For now, this driver has only been tested on just one Linux-Box.
-This one is running a 2.4.18 kernel with usb-uhci on an amd athlon 600.
+The number of buttons/axes reported varies based on 3 things:
+- if you are using a known controller
+- if you are using a known dance pad
+- if using an unknown device (one not listed below), what you set in the
+  module configuration for "Map D-PAD to buttons rather than axes for unknown
+  pads" (module option dpad_to_buttons)
 
-The jstest-program from joystick-1.2.15 (jstest-version 2.1.0) reports
-8 axes and 10 buttons.
+If you set dpad_to_buttons to 0 and you are using an unknown device (one
+not listed below), the driver will map the directional pad to axes (X/Y),
+if you said N it will map the d-pad to buttons, which is needed for dance
+style games to function correctly.  The default is Y.
+
+dpad_to_buttons has no effect for known pads.
+
+0.1 Normal Controllers
+----------------------
+With a normal controller, the directional pad is mapped to its own X/Y axes.
+The jstest-program from joystick-1.2.15 (jstest-version 2.1.0) will report 8
+axes and 10 buttons.
 
-Alls 8 axes work, though they all have the same range (-32768..32767)
+All 8 axes work, though they all have the same range (-32768..32767)
 and the zero-setting is not correct for the triggers (I don't know if that
 is some limitation of jstest, since the input device setup should be fine. I
 didn't have a look at jstest itself yet).
@@ -30,16 +47,50 @@ in game functionality were OK. However, I find it rather difficult to
 play first person shooters with a pad. Your mileage may vary.
 
 
+0.2 Xbox Dance Pads
+-------------------
+When using a known dance pad, jstest will report 6 axes and 14 buttons.
+
+For dance style pads (like the redoctane pad) several changes
+have been made.  The old driver would map the d-pad to axes, resulting
+in the driver being unable to report when the user was pressing both
+left+right or up+down, making DDR style games unplayable.
+
+Known dance pads automatically map the d-pad to buttons and will work
+correctly out of the box.
+
+If your dance pad is recognized by the driver but is using axes instead
+of buttons, see section 0.3 - Unknown Controllers
+
+I've tested this with Stepmania, and it works quite well.
+
+
+0.3 Unkown Controllers
+----------------------
+If you have an unkown xbox controller, it should work just fine with
+the default settings.
+
+HOWEVER if you have an unknown dance pad not listed below, it will not
+work UNLESS you set "dpad_to_buttons" to 1 in the module configuration.
+
+PLEASE if you have an unkown controller, email Dom <binary1230@yahoo.com> with
+a dump from /proc/bus/usb and a description of the pad (manufacturer, country,
+whether it is a dance pad or normal controller) so that we can add your pad
+to the list of supported devices, ensuring that it will work out of the
+box in the future.
+
+
 1. USB adapter
 --------------
 
 Before you can actually use the driver, you need to get yourself an
-adapter cable to connect the X-Box controller to your Linux-Box.
+adapter cable to connect the X-Box controller to your Linux-Box. You
+can buy these online fairly cheap, or build your own.
 
-Such a cable is pretty easy to build. The Controller itself is a USB compound
-device (a hub with three ports for two expansion slots and the controller
-device) with the only difference in a nonstandard connector (5 pins vs. 4 on
-standard USB connector).
+Such a cable is pretty easy to build. The Controller itself is a USB
+compound device (a hub with three ports for two expansion slots and
+the controller device) with the only difference in a nonstandard connector
+(5 pins vs. 4 on standard USB connector).
 
 You just need to solder a USB connector onto the cable and keep the
 yellow wire unconnected. The other pins have the same order on both
@@ -51,36 +102,36 @@ original one. You can buy an extension cable and cut that instead. That way,
 you can still use the controller with your X-Box, if you have one ;)
 
 
-2. driver installation
+2. Driver Installation
 ----------------------
 
 Once you have the adapter cable and the controller is connected, you need
 to load your USB subsystem and should cat /proc/bus/usb/devices.
 There should be an entry like the one at the end [4].
 
-Currently (as of version 0.0.4), the following three devices are included:
+Currently (as of version 0.0.6), the following devices are included:
  original Microsoft XBOX controller (US), vendor=0x045e, product=0x0202
+ smaller  Microsoft XBOX controller (US), vendor=0x045e, product=0x0289
  original Microsoft XBOX controller (Japan), vendor=0x045e, product=0x0285
  InterAct PowerPad Pro (Germany), vendor=0x05fd, product=0x107a
+ RedOctane Xbox Dance Pad (US), vendor=0x0c12, product=0x8809
 
-If you have another controller that is not listed above and is not recognized
-by the driver, please drop me a line with the appropriate info (that is, include
-the name, vendor and product ID, as well as the country where you bought it;
-sending the whole dump out of /proc/bus/usb/devices along would be even better).
+The driver should work with xbox pads not listed above as well, however
+you will need to do something extra for dance pads to work.
 
-In theory, the driver should work with other controllers than mine
-(InterAct PowerPad pro, bought in Germany) just fine, but I cannot test this
-for I only have this one controller.
+If you have a controller not listed above, see 0.3 - Unknown Controllers
 
 If you compiled and installed the driver, test the functionality:
 > modprobe xpad
 > modprobe joydev
 > jstest /dev/js0
 
-There should be a single line showing 18 inputs (8 axes, 10 buttons), and
-it's values should change if you move the sticks and push the buttons.
+If you're using a normal controller, there should be a single line showing
+18 inputs (8 axes, 10 buttons), and its values should change if you move
+the sticks and push the buttons.  If you're using a dance pad, it should
+show 20 inputs (6 axes, 14 buttons).
 
-It works? Voila, your done ;)
+It works? Voila, you're done ;)
 
 
 3. Thanks
@@ -111,6 +162,22 @@ I:  If#= 0 Alt= 0 #EPs= 2 Cls=58(unk. ) Sub=42 Prot=00 Driver=(none)
 E:  Ad=81(I) Atr=03(Int.) MxPS=  32 Ivl= 10ms
 E:  Ad=02(O) Atr=03(Int.) MxPS=  32 Ivl= 10ms
 
+5. /proc/bus/usb/devices - dump from Redoctane Xbox Dance Pad (US):
+
+T:  Bus=01 Lev=02 Prnt=09 Port=00 Cnt=01 Dev#= 10 Spd=12  MxCh= 0
+D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
+P:  Vendor=0c12 ProdID=8809 Rev= 0.01
+S:  Product=XBOX DDR
+C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
+I:  If#= 0 Alt= 0 #EPs= 2 Cls=58(unk. ) Sub=42 Prot=00 Driver=xpad
+E:  Ad=82(I) Atr=03(Int.) MxPS=  32 Ivl=4ms
+E:  Ad=02(O) Atr=03(Int.) MxPS=  32 Ivl=4ms
+
 -- 
 Marko Friedemann <mfr@bmx-chemnitz.de>
 2002-07-16
+ - original doc
+
+Dominic Cerquetti <binary1230@yahoo.com>
+2005-03-19
+ - added stuff for dance pads, new d-pad->axes mappings