1 files changed, 30 insertions, 2 deletions

diff --git a/Documentation/hwmon/abituguru b/Documentation/hwmon/abituguru
index 69cdb527d58f..b2c0d61b39a2 100644
--- a/Documentation/hwmon/abituguru
+++ b/Documentation/hwmon/abituguru
@@ -2,13 +2,36 @@ Kernel driver abituguru
 =======================
 
 Supported chips:
-  * Abit uGuru (Hardware Monitor part only)
+  * Abit uGuru revision 1-3 (Hardware Monitor part only)
     Prefix: 'abituguru'
     Addresses scanned: ISA 0x0E0
     Datasheet: Not available, this driver is based on reverse engineering.
         A "Datasheet" has been written based on the reverse engineering it
         should be available in the same dir as this file under the name
         abituguru-datasheet.
+    Note:
+        The uGuru is a microcontroller with onboard firmware which programs
+        it to behave as a hwmon IC. There are many different revisions of the
+        firmware and thus effectivly many different revisions of the uGuru.
+        Below is an incomplete list with which revisions are used for which
+        Motherboards:
+        uGuru 1.00    ~ 1.24    (AI7, KV8-MAX3, AN7) (1)
+        uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO)
+        uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8)
+        uGuru 2.2.0.0 ~ 2.2.0.6 (AA8 Fatal1ty)
+        uGuru 2.3.0.0 ~ 2.3.0.9 (AN8)
+        uGuru 3.0.0.0 ~ 3.0.1.2 (AW8, AL8, NI8)
+        uGuru 4.xxxxx?          (AT8 32X) (2)
+        1) For revisions 2 and 3 uGuru's the driver can autodetect the
+           sensortype (Volt or Temp) for bank1 sensors, for revision 1 uGuru's
+           this doesnot always work. For these uGuru's the autodection can
+           be overriden with the bank1_types module param. For all 3 known
+           revison 1 motherboards the correct use of this param is:
+           bank1_types=1,1,0,0,0,0,0,2,0,0,0,0,2,0,0,1
+           You may also need to specify the fan_sensors option for these boards
+           fan_sensors=5
+        2) The current version of the abituguru driver is known to NOT work
+           on these Motherboards
 
 Authors:
         Hans de Goede <j.w.r.degoede@hhs.nl>,
@@ -22,6 +45,11 @@ Module Parameters
 * force: bool           Force detection. Note this parameter only causes the
                         detection to be skipped, if the uGuru can't be read
                         the module initialization (insmod) will still fail.
+* bank1_types: int[]    Bank1 sensortype autodetection override:
+                          -1 autodetect (default)
+                           0 volt sensor
+                           1 temp sensor
+                           2 not connected
 * fan_sensors: int      Tell the driver how many fan speed sensors there are
                         on your motherboard. Default: 0 (autodetect).
 * pwms: int             Tell the driver how many fan speed controls (fan
@@ -29,7 +57,7 @@ Module Parameters
 * verbose: int          How verbose should the driver be? (0-3):
                            0 normal output
                            1 + verbose error reporting
-                           2 + sensors type probing info\n"
+                           2 + sensors type probing info (default)
                            3 + retryable error reporting
                         Default: 2 (the driver is still in the testing phase)