4 files changed, 114 insertions, 13 deletions

diff --git a/Documentation/hwmon/pcf8591 b/Documentation/hwmon/pcf8591
index 5628fcf4207f..e76a7892f68e 100644
--- a/Documentation/hwmon/pcf8591
+++ b/Documentation/hwmon/pcf8591
@@ -2,11 +2,11 @@ Kernel driver pcf8591
 =====================
 
 Supported chips:
-  * Philips PCF8591
+  * Philips/NXP PCF8591
     Prefix: 'pcf8591'
     Addresses scanned: I2C 0x48 - 0x4f
-    Datasheet: Publicly available at the Philips Semiconductor website
-               http://www.semiconductors.philips.com/pip/PCF8591P.html
+    Datasheet: Publicly available at the NXP website
+               http://www.nxp.com/pip/PCF8591_6.html
 
 Authors:
         Aurelien Jarno <aurelien@aurel32.net>
@@ -16,9 +16,10 @@ Authors:
 
 Description
 -----------
+
 The PCF8591 is an 8-bit A/D and D/A converter (4 analog inputs and one
-analog output) for the I2C bus produced by Philips Semiconductors. It
-is designed to provide a byte I2C interface to up to 4 separate devices.
+analog output) for the I2C bus produced by Philips Semiconductors (now NXP).
+It is designed to provide a byte I2C interface to up to 4 separate devices.
 
 The PCF8591 has 4 analog inputs programmable as single-ended or
 differential inputs :
@@ -58,8 +59,8 @@ Accessing PCF8591 via /sys interface
 -------------------------------------
 
 ! Be careful !
-The PCF8591 is plainly impossible to detect ! Stupid chip.
-So every chip with address in the interval [48..4f] is
+The PCF8591 is plainly impossible to detect! Stupid chip.
+So every chip with address in the interval [0x48..0x4f] is
 detected as PCF8591. If you have other chips in this address
 range, the workaround is to load this module after the one
 for your others chips.
@@ -67,19 +68,20 @@ for your others chips.
 On detection (i.e. insmod, modprobe et al.), directories are being
 created for each detected PCF8591:
 
-/sys/bus/devices/<0>-<1>/
+/sys/bus/i2c/devices/<0>-<1>/
 where <0> is the bus the chip was detected on (e. g. i2c-0)
 and <1> the chip address ([48..4f])
 
 Inside these directories, there are such files:
-in0, in1, in2, in3, out0_enable, out0_output, name
+in0_input, in1_input, in2_input, in3_input, out0_enable, out0_output, name
 
 Name contains chip name.
 
-The in0, in1, in2 and in3 files are RO. Reading gives the value of the
-corresponding channel. Depending on the current analog inputs configuration,
-files in2 and/or in3 do not exist. Values range are from 0 to 255 for single
-ended inputs and -128 to +127 for differential inputs (8-bit ADC).
+The in0_input, in1_input, in2_input and in3_input files are RO. Reading gives
+the value of the corresponding channel. Depending on the current analog inputs
+configuration, files in2_input and in3_input may not exist. Values range
+from 0 to 255 for single ended inputs and -128 to +127 for differential inputs
+(8-bit ADC).
 
 The out0_enable file is RW. Reading gives "1" for analog output enabled and
 "0" for analog output disabled. Writing accepts "0" and "1" accordingly.
diff --git a/Documentation/hwmon/tmp421 b/Documentation/hwmon/tmp421
new file mode 100644
index 000000000000..0cf07f824741
--- /dev/null
+++ b/Documentation/hwmon/tmp421
@@ -0,0 +1,36 @@
+Kernel driver tmp421
+====================
+
+Supported chips:
+  * Texas Instruments TMP421
+    Prefix: 'tmp421'
+    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+  * Texas Instruments TMP422
+    Prefix: 'tmp422'
+    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+  * Texas Instruments TMP423
+    Prefix: 'tmp423'
+    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+
+Authors:
+        Andre Prendel <andre.prendel@gmx.de>
+
+Description
+-----------
+
+This driver implements support for Texas Instruments TMP421, TMP422
+and TMP423 temperature sensor chips. These chips implement one local
+and up to one (TMP421), up to two (TMP422) or up to three (TMP423)
+remote sensors. Temperature is measured in degrees Celsius. The chips
+are wired over I2C/SMBus and specified over a temperature range of -40
+to +125 degrees Celsius. Resolution for both the local and remote
+channels is 0.0625 degree C.
+
+The chips support only temperature measurement. The driver exports
+the temperature values via the following sysfs files:
+
+temp[1-4]_input
+temp[2-4]_fault
diff --git a/Documentation/hwmon/wm831x b/Documentation/hwmon/wm831x
new file mode 100644
index 000000000000..24f47d8f6a42
--- /dev/null
+++ b/Documentation/hwmon/wm831x
@@ -0,0 +1,37 @@
+Kernel driver wm831x-hwmon
+==========================
+
+Supported chips:
+  * Wolfson Microelectronics WM831x PMICs
+    Prefix: 'wm831x'
+    Datasheet:
+        http://www.wolfsonmicro.com/products/WM8310
+        http://www.wolfsonmicro.com/products/WM8311
+        http://www.wolfsonmicro.com/products/WM8312
+
+Authors: Mark Brown <broonie@opensource.wolfsonmicro.com>
+
+Description
+-----------
+
+The WM831x series of PMICs include an AUXADC which can be used to
+monitor a range of system operating parameters, including the voltages
+of the major supplies within the system.  Currently the driver provides
+reporting of all the input values but does not provide any alarms.
+
+Voltage Monitoring
+------------------
+
+Voltages are sampled by a 12 bit ADC.  Voltages in milivolts are 1.465
+times the ADC value.
+
+Temperature Monitoring
+----------------------
+
+Temperatures are sampled by a 12 bit ADC.  Chip and battery temperatures
+are available.  The chip temperature is calculated as:
+
+        Degrees celsius = (512.18 - data) / 1.0983
+
+while the battery temperature calculation will depend on the NTC
+thermistor component.
diff --git a/Documentation/hwmon/wm8350 b/Documentation/hwmon/wm8350
new file mode 100644
index 000000000000..98f923bd2e92
--- /dev/null
+++ b/Documentation/hwmon/wm8350
@@ -0,0 +1,26 @@
+Kernel driver wm8350-hwmon
+==========================
+
+Supported chips:
+  * Wolfson Microelectronics WM835x PMICs
+    Prefix: 'wm8350'
+    Datasheet:
+        http://www.wolfsonmicro.com/products/WM8350
+        http://www.wolfsonmicro.com/products/WM8351
+        http://www.wolfsonmicro.com/products/WM8352
+
+Authors: Mark Brown <broonie@opensource.wolfsonmicro.com>
+
+Description
+-----------
+
+The WM835x series of PMICs include an AUXADC which can be used to
+monitor a range of system operating parameters, including the voltages
+of the major supplies within the system.  Currently the driver provides
+simple access to these major supplies.
+
+Voltage Monitoring
+------------------
+
+Voltages are sampled by a 12 bit ADC.  For the internal supplies the ADC
+is referenced to the system VRTC.