5 files changed, 108 insertions, 6 deletions

diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp
new file mode 100644
index 000000000000..870cda9416e9
--- /dev/null
+++ b/Documentation/hwmon/coretemp
@@ -0,0 +1,36 @@
+Kernel driver coretemp
+======================
+
+Supported chips:
+  * All Intel Core family
+    Prefix: 'coretemp'
+    CPUID: family 0x6, models 0xe, 0xf
+    Datasheet: Intel 64 and IA-32 Architectures Software Developer's Manual
+               Volume 3A: System Programming Guide
+
+Author: Rudolf Marek
+
+Description
+-----------
+
+This driver permits reading temperature sensor embedded inside Intel Core CPU.
+Temperature is measured in degrees Celsius and measurement resolution is
+1 degree C. Valid temperatures are from 0 to TjMax degrees C, because
+the actual value of temperature register is in fact a delta from TjMax.
+
+Temperature known as TjMax is the maximum junction temperature of processor.
+Intel defines this temperature as 85C or 100C. At this temperature, protection
+mechanism will perform actions to forcibly cool down the processor. Alarm
+may be raised, if the temperature grows enough (more than TjMax) to trigger
+the Out-Of-Spec bit. Following table summarizes the exported sysfs files:
+
+temp1_input      - Core temperature (in millidegrees Celsius).
+temp1_crit       - Maximum junction temperature  (in millidegrees Celsius).
+temp1_crit_alarm - Set when Out-of-spec bit is set, never clears.
+                   Correct CPU operation is no longer guaranteed.
+temp1_label      - Contains string "Core X", where X is processor
+                   number.
+
+The TjMax temperature is set to 85 degrees C if undocumented model specific
+register (UMSR) 0xee has bit 30 set. If not the TjMax is 100 degrees C as
+(sometimes) documented in processor datasheet.
diff --git a/Documentation/hwmon/max6650 b/Documentation/hwmon/max6650
new file mode 100644
index 000000000000..8be7beb9e3e8
--- /dev/null
+++ b/Documentation/hwmon/max6650
@@ -0,0 +1,53 @@
+Kernel driver max6650
+=====================
+
+Supported chips:
+  * Maxim 6650 / 6651
+    Prefix: 'max6650'
+    Addresses scanned: I2C 0x1b, 0x1f, 0x48, 0x4b
+    Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6650-MAX6651.pdf
+
+Authors:
+    Hans J. Koch <hjk@linutronix.de>
+    John Morris <john.morris@spirentcom.com>
+    Claus Gindhart <claus.gindhart@kontron.com>
+
+Description
+-----------
+
+This driver implements support for the Maxim 6650/6651
+
+The 2 devices are very similar, but the Maxim 6550 has a reduced feature
+set, e.g. only one fan-input, instead of 4 for the 6651.
+
+The driver is not able to distinguish between the 2 devices.
+
+The driver provides the following sensor accesses in sysfs:
+
+fan1_input      ro      fan tachometer speed in RPM
+fan2_input      ro      "
+fan3_input      ro      "
+fan4_input      ro      "
+fan1_target     rw      desired fan speed in RPM (closed loop mode only)
+pwm1_enable     rw      regulator mode, 0=full on, 1=open loop, 2=closed loop
+pwm1            rw      relative speed (0-255), 255=max. speed.
+                        Used in open loop mode only.
+fan1_div        rw      sets the speed range the inputs can handle. Legal
+                        values are 1, 2, 4, and 8. Use lower values for
+                        faster fans.
+
+Module parameters
+-----------------
+
+If your board has a BIOS that initializes the MAX6650/6651 correctly, you can
+simply load your module without parameters. It won't touch the configuration
+registers then. If your board BIOS doesn't initialize the chip, or you want
+different settings, you can set the following parameters:
+
+voltage_12V: 5=5V fan, 12=12V fan, 0=don't change
+prescaler: Possible values are 1,2,4,8,16, or 0 for don't change
+clock: The clock frequency in Hz of the chip the driver should assume [254000]
+
+Please have a look at the MAX6650/6651 data sheet and make sure that you fully
+understand the meaning of these parameters before you attempt to change them.
+
diff --git a/Documentation/hwmon/smsc47m1 b/Documentation/hwmon/smsc47m1
index 04a11124f667..42c8431b3c9d 100644
--- a/Documentation/hwmon/smsc47m1
+++ b/Documentation/hwmon/smsc47m1
@@ -14,6 +14,10 @@ Supported chips:
         http://www.smsc.com/main/datasheets/47m14x.pdf
         http://www.smsc.com/main/tools/discontinued/47m15x.pdf
         http://www.smsc.com/main/datasheets/47m192.pdf
+  * SMSC LPC47M292
+    Addresses scanned: none, address read from Super I/O config space
+    Prefix: 'smsc47m2'
+    Datasheet: Not public
   * SMSC LPC47M997
     Addresses scanned: none, address read from Super I/O config space
     Prefix: 'smsc47m1'
@@ -32,9 +36,10 @@ Description
 The Standard Microsystems Corporation (SMSC) 47M1xx Super I/O chips
 contain monitoring and PWM control circuitry for two fans.
 
-The 47M15x and 47M192 chips contain a full 'hardware monitoring block'
-in addition to the fan monitoring and control. The hardware monitoring
-block is not supported by the driver.
+The LPC47M15x, LPC47M192 and LPC47M292 chips contain a full 'hardware
+monitoring block' in addition to the fan monitoring and control. The
+hardware monitoring block is not supported by this driver, use the
+smsc47m192 driver for that.
 
 No documentation is available for the 47M997, but it has the same device
 ID as the 47M15x and 47M192 chips and seems to be compatible.
diff --git a/Documentation/hwmon/smsc47m192 b/Documentation/hwmon/smsc47m192
index 45d6453cd435..6d54ecb7b3f8 100644
--- a/Documentation/hwmon/smsc47m192
+++ b/Documentation/hwmon/smsc47m192
@@ -2,12 +2,13 @@ Kernel driver smsc47m192
 ========================
 
 Supported chips:
-  * SMSC LPC47M192 and LPC47M997
+  * SMSC LPC47M192, LPC47M15x, LPC47M292 and LPC47M997
     Prefix: 'smsc47m192'
     Addresses scanned: I2C 0x2c - 0x2d
     Datasheet: The datasheet for LPC47M192 is publicly available from
                http://www.smsc.com/
-               The LPC47M997 is compatible for hardware monitoring.
+               The LPC47M15x, LPC47M292 and LPC47M997 are compatible for
+               hardware monitoring.
 
 Author: Hartmut Rick <linux@rick.claranet.de>
         Special thanks to Jean Delvare for careful checking
@@ -18,7 +19,7 @@ Description
 -----------
 
 This driver implements support for the hardware sensor capabilities
-of the SMSC LPC47M192 and LPC47M997 Super-I/O chips.
+of the SMSC LPC47M192 and compatible Super-I/O chips.
 
 These chips support 3 temperature channels and 8 voltage inputs
 as well as CPU voltage VID input.
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index d73d2e8c7534..a9a18ad0d17a 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -152,6 +152,13 @@ fan[1-*]_div	Fan divisor.
                 Note that this is actually an internal clock divisor, which
                 affects the measurable speed range, not the read value.
 
+fan[1-*]_target
+                Desired fan speed
+                Unit: revolution/min (RPM)
+                RW
+                Only makes sense if the chip supports closed-loop fan speed
+                control based on the measured fan speed.
+
 Also see the Alarms section for status flags associated with fans.