1 files changed, 0 insertions, 100 deletions

diff --git a/Documentation/cdrom/isp16 b/Documentation/cdrom/isp16
deleted file mode 100644
index cc86533ac9f3..000000000000
--- a/Documentation/cdrom/isp16
+++ /dev/null
@@ -1,100 +0,0 @@
- -- Documentation/cdrom/isp16
-
-Docs by Eric van der Maarel <H.T.M.v.d.Maarel@marin.nl>
-
-This is the README for version 0.6 of the cdrom interface on an
-ISP16, MAD16 or Mozart sound card.
-
-The detection and configuration of this interface used to be included
-in both the sjcd and optcd cdrom driver. Drives supported by these
-drivers came packed with Media Magic's multi media kit, which also
-included the ISP16 card. The idea (thanks Leo Spiekman)
-to move it from these drivers into a separate module and moreover, not to
-rely on the MAD16 sound driver, are as follows:
--duplication of code in the kernel is a waste of resources and should
- be avoided;
--however, kernels and notably those included with Linux distributions
- (cf Slackware 3.0 included version 0.5 of the isp16 configuration
- code included in the drivers) don't always come with sound support
- included. Especially when they already include a bunch of cdrom drivers.
- Hence, the cdrom interface should be configurable _independently_ of
- sound support.
-
-The ISP16, MAD16 and Mozart sound cards have an OPTi 82C928 or an
-OPTi 82C929 chip.  The interface on these cards should work with
-any cdrom attached to the card, which is 'electrically' compatible
-with Sanyo/Panasonic, Sony or Mitsumi non-ide drives. However, the
-command sets for any proprietary drives may differ
-(and hence may not be supported in the kernel) from these four types.
-For a fact I know the interface works and the way of configuration
-as described in this documentation works in combination with the
-sjcd (in Sanyo/Panasonic compatibility mode) cdrom drivers
-(probably with the optcd (in Sony compatibility mode) as well).
-If you have such an OPTi based sound card and you want to use the
-cdrom interface with a cdrom drive supported by any of the other cdrom
-drivers, it will probably work. Please let me know any experience you
-might have).
-I understand that cards based on the OPTi 82C929 chips may be configured
-(hardware jumpers that is) as an IDE interface. Initialisation of such a
-card in this mode is not supported (yet?).
-
-The suggestion to configure the ISP16 etc. sound card by booting DOS and 
-do a warm reboot to boot Linux somehow doesn't work, at least not
-on my machine (IPC P90), with the OPTi 82C928 based card.
-
-Booting the kernel through the boot manager LILO allows the use
-of some command line options on the 'LILO boot:' prompt. At boot time
-press Alt or Shift while the LILO prompt is written on the screen and enter
-any kernel options. Alternatively these options may be used in
-the appropriate section in /etc/lilo.conf. Adding 'append="<cmd_line_options>"'
-will do the trick as well.
-The syntax of 'cmd_line_options' is
-
-        isp16=[<port>[,<irq>[,<dma>]]][[,]<drive_type>]
-
-If there is no ISP16 or compatibles detected, there's probably no harm done.
-These options indicate the values that your cdrom drive has been (or will be)
-configured to use.
-Valid values for the base i/o address are:
-  port=0x340,0x320,0x330,0x360
-for the interrupt request number 
-  irq=0,3,5,7,9,10,11
-for the direct memory access line
-  dma=0,3,5,6,7
-and for the type of drive
-  drive_type=noisp16,Sanyo,Panasonic,Sony,Mitsumi.
-Note that these options are case sensitive.
-The values 0 for irq and dma indicate that they are not used, and
-the drive will be used in 'polling' mode. The values 5 and 7 for irq
-should be avoided in order to avoid any conflicts with optional
-sound card configuration.
-The syntax of the command line does not allow the specification of
-irq when there's nothing specified for the base address and no
-specification of dma when there is no specification of irq.
-The value 'noisp16' for drive_type, which may be used as the first
-non-integer option value (e.g. 'isp16=noisp16'), makes sure that probing
-for and subsequent configuration of an ISP16-compatible card is skipped
-all together. This can be useful to overcome possible conflicts which
-may arise while the kernel is probing your hardware.
-The default values are
-  port=0x340
-  irq=0
-  dma=0
-  drive_type=Sanyo
-reflecting my own configuration. The defaults can be changed in
-the file linux/drivers/cdrom/ips16.h.
-
-The cdrom interface can be configured at run time by loading the
-initialisation driver as a module. In that case, the interface
-parameters can be set by giving appropriate values on the command
-line. Configuring the driver can then be done by the following
-command (assuming you have iso16.o installed in a proper place):
-
-  insmod isp16.o isp16_cdrom_base=<port> isp16_cdrom_irq=<irq> \
-    isp16_cdrom_dma=<dma> isp16_cdrom_type=<drive_type>
-
-where port, irq, dma and drive_type can have any of the values mentioned
-above.
-
-
-Have fun!