aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--arch/blackfin/configs/BF527-TLL6527M_defconfig180
-rw-r--r--arch/blackfin/mach-bf527/boards/Kconfig5
-rw-r--r--arch/blackfin/mach-bf527/boards/Makefile1
-rw-r--r--arch/blackfin/mach-bf527/boards/tll6527m.c986
4 files changed, 1172 insertions, 0 deletions
diff --git a/arch/blackfin/configs/BF527-TLL6527M_defconfig b/arch/blackfin/configs/BF527-TLL6527M_defconfig
new file mode 100644
index 000000000000..92ded5edc86c
--- /dev/null
+++ b/arch/blackfin/configs/BF527-TLL6527M_defconfig
@@ -0,0 +1,180 @@
1CONFIG_EXPERIMENTAL=y
2CONFIG_LOCALVERSION="DEV_0-1_pre2010"
3CONFIG_SYSVIPC=y
4CONFIG_IKCONFIG=y
5CONFIG_IKCONFIG_PROC=y
6CONFIG_LOG_BUF_SHIFT=14
7CONFIG_BLK_DEV_INITRD=y
8# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
9CONFIG_EMBEDDED=y
10# CONFIG_SYSCTL_SYSCALL is not set
11# CONFIG_ELF_CORE is not set
12# CONFIG_FUTEX is not set
13# CONFIG_SIGNALFD is not set
14# CONFIG_TIMERFD is not set
15# CONFIG_EVENTFD is not set
16# CONFIG_AIO is not set
17CONFIG_SLAB=y
18CONFIG_MMAP_ALLOW_UNINITIALIZED=y
19CONFIG_MODULES=y
20CONFIG_MODULE_UNLOAD=y
21# CONFIG_LBDAF is not set
22# CONFIG_BLK_DEV_BSG is not set
23# CONFIG_IOSCHED_DEADLINE is not set
24CONFIG_PREEMPT_VOLUNTARY=y
25CONFIG_BF527=y
26CONFIG_BF_REV_0_2=y
27CONFIG_BFIN527_TLL6527M=y
28CONFIG_BF527_UART1_PORTG=y
29CONFIG_IRQ_USB_INT0=11
30CONFIG_IRQ_USB_INT1=11
31CONFIG_IRQ_USB_INT2=11
32CONFIG_IRQ_USB_DMA=11
33CONFIG_BOOT_LOAD=0x400000
34# CONFIG_CYCLES_CLOCKSOURCE is not set
35# CONFIG_SCHEDULE_L1 is not set
36# CONFIG_MEMSET_L1 is not set
37# CONFIG_MEMCPY_L1 is not set
38# CONFIG_SYS_BFIN_SPINLOCK_L1 is not set
39CONFIG_NOMMU_INITIAL_TRIM_EXCESS=0
40CONFIG_BFIN_GPTIMERS=y
41CONFIG_DMA_UNCACHED_2M=y
42CONFIG_C_CDPRIO=y
43CONFIG_BANK_0=0xFFC2
44CONFIG_BANK_1=0xFFC2
45CONFIG_BANK_2=0xFFC2
46CONFIG_BANK_3=0xFFC2
47CONFIG_BINFMT_FLAT=y
48CONFIG_BINFMT_ZFLAT=y
49CONFIG_NET=y
50CONFIG_PACKET=y
51CONFIG_UNIX=y
52CONFIG_INET=y
53CONFIG_IP_PNP=y
54# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
55# CONFIG_INET_XFRM_MODE_TUNNEL is not set
56# CONFIG_INET_XFRM_MODE_BEET is not set
57# CONFIG_INET_LRO is not set
58# CONFIG_INET_DIAG is not set
59# CONFIG_IPV6 is not set
60CONFIG_IRDA=m
61CONFIG_IRLAN=m
62CONFIG_IRCOMM=m
63CONFIG_IRTTY_SIR=m
64CONFIG_BFIN_SIR=m
65CONFIG_BFIN_SIR0=y
66# CONFIG_WIRELESS is not set
67CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
68# CONFIG_FW_LOADER is not set
69CONFIG_MTD=y
70CONFIG_MTD_CHAR=y
71CONFIG_MTD_BLOCK=y
72CONFIG_MTD_CFI=y
73CONFIG_MTD_CFI_INTELEXT=y
74CONFIG_MTD_RAM=y
75CONFIG_MTD_ROM=y
76CONFIG_MTD_COMPLEX_MAPPINGS=y
77CONFIG_MTD_GPIO_ADDR=y
78CONFIG_BLK_DEV_RAM=y
79CONFIG_SCSI=y
80# CONFIG_SCSI_PROC_FS is not set
81CONFIG_BLK_DEV_SD=y
82CONFIG_BLK_DEV_SR=m
83# CONFIG_SCSI_LOWLEVEL is not set
84CONFIG_NETDEVICES=y
85CONFIG_NET_ETHERNET=y
86CONFIG_BFIN_MAC=y
87# CONFIG_NETDEV_1000 is not set
88# CONFIG_NETDEV_10000 is not set
89# CONFIG_WLAN is not set
90# CONFIG_INPUT_MOUSEDEV is not set
91CONFIG_INPUT_EVDEV=y
92# CONFIG_INPUT_KEYBOARD is not set
93# CONFIG_INPUT_MOUSE is not set
94CONFIG_INPUT_TOUCHSCREEN=y
95CONFIG_TOUCHSCREEN_AD7879=m
96CONFIG_INPUT_MISC=y
97CONFIG_INPUT_AD714X=y
98CONFIG_INPUT_ADXL34X=y
99# CONFIG_SERIO is not set
100CONFIG_BFIN_PPI=m
101CONFIG_BFIN_SIMPLE_TIMER=m
102CONFIG_BFIN_SPORT=m
103# CONFIG_CONSOLE_TRANSLATIONS is not set
104# CONFIG_DEVKMEM is not set
105CONFIG_BFIN_JTAG_COMM=m
106CONFIG_SERIAL_BFIN=y
107CONFIG_SERIAL_BFIN_CONSOLE=y
108CONFIG_SERIAL_BFIN_UART1=y
109# CONFIG_LEGACY_PTYS is not set
110# CONFIG_HW_RANDOM is not set
111CONFIG_I2C_CHARDEV=y
112# CONFIG_I2C_HELPER_AUTO is not set
113CONFIG_I2C_SMBUS=y
114CONFIG_I2C_BLACKFIN_TWI=y
115CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
116CONFIG_GPIOLIB=y
117CONFIG_GPIO_SYSFS=y
118# CONFIG_HWMON is not set
119CONFIG_WATCHDOG=y
120CONFIG_BFIN_WDT=y
121CONFIG_MEDIA_SUPPORT=y
122CONFIG_VIDEO_DEV=y
123# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
124CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
125CONFIG_VIDEO_BLACKFIN_CAM=m
126CONFIG_OV9655=y
127CONFIG_FB=y
128CONFIG_BACKLIGHT_LCD_SUPPORT=y
129CONFIG_FRAMEBUFFER_CONSOLE=y
130CONFIG_FONTS=y
131CONFIG_FONT_6x11=y
132CONFIG_LOGO=y
133# CONFIG_LOGO_LINUX_MONO is not set
134# CONFIG_LOGO_LINUX_VGA16 is not set
135# CONFIG_LOGO_LINUX_CLUT224 is not set
136# CONFIG_LOGO_BLACKFIN_VGA16 is not set
137CONFIG_SOUND=y
138CONFIG_SND=y
139CONFIG_SND_MIXER_OSS=y
140CONFIG_SND_PCM_OSS=y
141CONFIG_SND_SOC=y
142CONFIG_SND_BF5XX_I2S=y
143CONFIG_SND_BF5XX_SOC_SSM2602=y
144# CONFIG_HID_SUPPORT is not set
145# CONFIG_USB_SUPPORT is not set
146CONFIG_MMC=m
147CONFIG_RTC_CLASS=y
148CONFIG_RTC_DRV_BFIN=y
149CONFIG_EXT2_FS=y
150# CONFIG_DNOTIFY is not set
151CONFIG_ISO9660_FS=m
152CONFIG_JOLIET=y
153CONFIG_UDF_FS=m
154CONFIG_MSDOS_FS=y
155CONFIG_VFAT_FS=y
156CONFIG_JFFS2_FS=y
157CONFIG_NFS_FS=m
158CONFIG_NFS_V3=y
159# CONFIG_RPCSEC_GSS_KRB5 is not set
160CONFIG_NLS_CODEPAGE_437=m
161CONFIG_NLS_CODEPAGE_936=m
162CONFIG_NLS_ISO8859_1=m
163CONFIG_NLS_UTF8=m
164CONFIG_DEBUG_KERNEL=y
165CONFIG_DEBUG_SHIRQ=y
166CONFIG_DETECT_HUNG_TASK=y
167CONFIG_DEBUG_INFO=y
168# CONFIG_RCU_CPU_STALL_DETECTOR is not set
169# CONFIG_FTRACE is not set
170CONFIG_DEBUG_MMRS=y
171CONFIG_DEBUG_HWERR=y
172CONFIG_EXACT_HWERR=y
173CONFIG_DEBUG_DOUBLEFAULT=y
174CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE=y
175CONFIG_EARLY_PRINTK=y
176CONFIG_CPLB_INFO=y
177CONFIG_SECURITY=y
178CONFIG_CRYPTO=y
179# CONFIG_CRYPTO_ANSI_CPRNG is not set
180CONFIG_CRC7=m
diff --git a/arch/blackfin/mach-bf527/boards/Kconfig b/arch/blackfin/mach-bf527/boards/Kconfig
index 646bc66def64..1cc2667c10f1 100644
--- a/arch/blackfin/mach-bf527/boards/Kconfig
+++ b/arch/blackfin/mach-bf527/boards/Kconfig
@@ -29,4 +29,9 @@ config BFIN527_AD7160EVAL
29 help 29 help
30 BF527-AD7160-EVAL board support. 30 BF527-AD7160-EVAL board support.
31 31
32config BFIN527_TLL6527M
33 bool "The Learning Labs TLL6527M"
34 help
35 TLL6527M V1.0 platform support
36
32endchoice 37endchoice
diff --git a/arch/blackfin/mach-bf527/boards/Makefile b/arch/blackfin/mach-bf527/boards/Makefile
index 751d45cdf722..1d67da9f05ac 100644
--- a/arch/blackfin/mach-bf527/boards/Makefile
+++ b/arch/blackfin/mach-bf527/boards/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_BFIN527_EZKIT_V2) += ezkit.o
7obj-$(CONFIG_BFIN527_BLUETECHNIX_CM) += cm_bf527.o 7obj-$(CONFIG_BFIN527_BLUETECHNIX_CM) += cm_bf527.o
8obj-$(CONFIG_BFIN526_EZBRD) += ezbrd.o 8obj-$(CONFIG_BFIN526_EZBRD) += ezbrd.o
9obj-$(CONFIG_BFIN527_AD7160EVAL) += ad7160eval.o 9obj-$(CONFIG_BFIN527_AD7160EVAL) += ad7160eval.o
10obj-$(CONFIG_BFIN527_TLL6527M) += tll6527m.o
diff --git a/arch/blackfin/mach-bf527/boards/tll6527m.c b/arch/blackfin/mach-bf527/boards/tll6527m.c
new file mode 100644
index 000000000000..ae4130e97c01
--- /dev/null
+++ b/arch/blackfin/mach-bf527/boards/tll6527m.c
@@ -0,0 +1,986 @@
1/* File: arch/blackfin/mach-bf527/boards/tll6527m.c
2 * Based on: arch/blackfin/mach-bf527/boards/ezkit.c
3 * Author: Ashish Gupta
4 *
5 * Copyright: 2010 - The Learning Labs Inc.
6 *
7 * Licensed under the GPL-2 or later.
8 */
9
10#include <linux/device.h>
11#include <linux/platform_device.h>
12#include <linux/mtd/mtd.h>
13#include <linux/mtd/partitions.h>
14#include <linux/mtd/physmap.h>
15#include <linux/spi/spi.h>
16#include <linux/spi/flash.h>
17#include <linux/i2c.h>
18#include <linux/irq.h>
19#include <linux/interrupt.h>
20#include <linux/usb/musb.h>
21#include <linux/leds.h>
22#include <linux/input.h>
23#include <asm/dma.h>
24#include <asm/bfin5xx_spi.h>
25#include <asm/reboot.h>
26#include <asm/nand.h>
27#include <asm/portmux.h>
28#include <asm/dpmc.h>
29
30#if defined(CONFIG_TOUCHSCREEN_AD7879) \
31 || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
32#include <linux/spi/ad7879.h>
33#define LCD_BACKLIGHT_GPIO 0x40
34/* TLL6527M uses TLL7UIQ35 / ADI LCD EZ Extender. AD7879 AUX GPIO is used for
35 * LCD Backlight Enable
36 */
37#endif
38
39/*
40 * Name the Board for the /proc/cpuinfo
41 */
42const char bfin_board_name[] = "TLL6527M";
43/*
44 * Driver needs to know address, irq and flag pin.
45 */
46
47#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
48static struct resource musb_resources[] = {
49 [0] = {
50 .start = 0xffc03800,
51 .end = 0xffc03cff,
52 .flags = IORESOURCE_MEM,
53 },
54 [1] = { /* general IRQ */
55 .start = IRQ_USB_INT0,
56 .end = IRQ_USB_INT0,
57 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
58 },
59 [2] = { /* DMA IRQ */
60 .start = IRQ_USB_DMA,
61 .end = IRQ_USB_DMA,
62 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
63 },
64};
65
66static struct musb_hdrc_config musb_config = {
67 .multipoint = 0,
68 .dyn_fifo = 0,
69 .soft_con = 1,
70 .dma = 1,
71 .num_eps = 8,
72 .dma_channels = 8,
73 /*.gpio_vrsel = GPIO_PG13,*/
74 /* Some custom boards need to be active low, just set it to "0"
75 * if it is the case.
76 */
77 .gpio_vrsel_active = 1,
78};
79
80static struct musb_hdrc_platform_data musb_plat = {
81#if defined(CONFIG_USB_MUSB_OTG)
82 .mode = MUSB_OTG,
83#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
84 .mode = MUSB_HOST,
85#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
86 .mode = MUSB_PERIPHERAL,
87#endif
88 .config = &musb_config,
89};
90
91static u64 musb_dmamask = ~(u32)0;
92
93static struct platform_device musb_device = {
94 .name = "musb_hdrc",
95 .id = 0,
96 .dev = {
97 .dma_mask = &musb_dmamask,
98 .coherent_dma_mask = 0xffffffff,
99 .platform_data = &musb_plat,
100 },
101 .num_resources = ARRAY_SIZE(musb_resources),
102 .resource = musb_resources,
103};
104#endif
105
106#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
107#include <asm/bfin-lq035q1.h>
108
109static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
110 .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
111 .ppi_mode = USE_RGB565_16_BIT_PPI,
112 .use_bl = 1,
113 .gpio_bl = LCD_BACKLIGHT_GPIO,
114};
115
116static struct resource bfin_lq035q1_resources[] = {
117 {
118 .start = IRQ_PPI_ERROR,
119 .end = IRQ_PPI_ERROR,
120 .flags = IORESOURCE_IRQ,
121 },
122};
123
124static struct platform_device bfin_lq035q1_device = {
125 .name = "bfin-lq035q1",
126 .id = -1,
127 .num_resources = ARRAY_SIZE(bfin_lq035q1_resources),
128 .resource = bfin_lq035q1_resources,
129 .dev = {
130 .platform_data = &bfin_lq035q1_data,
131 },
132};
133#endif
134
135#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
136static struct mtd_partition tll6527m_partitions[] = {
137 {
138 .name = "bootloader(nor)",
139 .size = 0xA0000,
140 .offset = 0,
141 }, {
142 .name = "linux kernel(nor)",
143 .size = 0xD00000,
144 .offset = MTDPART_OFS_APPEND,
145 }, {
146 .name = "file system(nor)",
147 .size = MTDPART_SIZ_FULL,
148 .offset = MTDPART_OFS_APPEND,
149 }
150};
151
152static struct physmap_flash_data tll6527m_flash_data = {
153 .width = 2,
154 .parts = tll6527m_partitions,
155 .nr_parts = ARRAY_SIZE(tll6527m_partitions),
156};
157
158static unsigned tll6527m_flash_gpios[] = { GPIO_PG11, GPIO_PH11, GPIO_PH12 };
159
160static struct resource tll6527m_flash_resource[] = {
161 {
162 .name = "cfi_probe",
163 .start = 0x20000000,
164 .end = 0x201fffff,
165 .flags = IORESOURCE_MEM,
166 }, {
167 .start = (unsigned long)tll6527m_flash_gpios,
168 .end = ARRAY_SIZE(tll6527m_flash_gpios),
169 .flags = IORESOURCE_IRQ,
170 }
171};
172
173static struct platform_device tll6527m_flash_device = {
174 .name = "gpio-addr-flash",
175 .id = 0,
176 .dev = {
177 .platform_data = &tll6527m_flash_data,
178 },
179 .num_resources = ARRAY_SIZE(tll6527m_flash_resource),
180 .resource = tll6527m_flash_resource,
181};
182#endif
183
184#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
185/* An SN74LVC138A 3:8 decoder chip has been used to generate 7 augmented
186 * outputs used as SPI CS lines for all SPI SLAVE devices on TLL6527v1-0.
187 * EXP_GPIO_SPISEL_BASE is the base number for the expanded outputs being
188 * used as SPI CS lines, this should be > MAX_BLACKFIN_GPIOS
189 */
190#include <linux/gpio-decoder.h>
191#define EXP_GPIO_SPISEL_BASE 0x64
192static unsigned gpio_addr_inputs[] = {
193 GPIO_PG1, GPIO_PH9, GPIO_PH10
194};
195
196static struct gpio_decoder_platfrom_data spi_decoded_cs = {
197 .base = EXP_GPIO_SPISEL_BASE,
198 .input_addrs = gpio_addr_inputs,
199 .nr_input_addrs = ARRAY_SIZE(gpio_addr_inputs),
200 .default_output = 0,
201/* .default_output = (1 << ARRAY_SIZE(gpio_addr_inputs)) - 1 */
202};
203
204static struct platform_device spi_decoded_gpio = {
205 .name = "gpio-decoder",
206 .id = 0,
207 .dev = {
208 .platform_data = &spi_decoded_cs,
209 },
210};
211
212#else
213#define EXP_GPIO_SPISEL_BASE 0x0
214
215#endif
216
217#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
218#include <linux/input/adxl34x.h>
219static const struct adxl34x_platform_data adxl345_info = {
220 .x_axis_offset = 0,
221 .y_axis_offset = 0,
222 .z_axis_offset = 0,
223 .tap_threshold = 0x31,
224 .tap_duration = 0x10,
225 .tap_latency = 0x60,
226 .tap_window = 0xF0,
227 .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
228 .act_axis_control = 0xFF,
229 .activity_threshold = 5,
230 .inactivity_threshold = 2,
231 .inactivity_time = 2,
232 .free_fall_threshold = 0x7,
233 .free_fall_time = 0x20,
234 .data_rate = 0x8,
235 .data_range = ADXL_FULL_RES,
236
237 .ev_type = EV_ABS,
238 .ev_code_x = ABS_X, /* EV_REL */
239 .ev_code_y = ABS_Y, /* EV_REL */
240 .ev_code_z = ABS_Z, /* EV_REL */
241
242 .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
243
244/* .ev_code_ff = KEY_F,*/ /* EV_KEY */
245 .ev_code_act_inactivity = KEY_A, /* EV_KEY */
246 .use_int2 = 1,
247 .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
248 .fifo_mode = ADXL_FIFO_STREAM,
249};
250#endif
251
252#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
253static struct platform_device rtc_device = {
254 .name = "rtc-bfin",
255 .id = -1,
256};
257#endif
258
259#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
260static struct platform_device bfin_mii_bus = {
261 .name = "bfin_mii_bus",
262};
263
264static struct platform_device bfin_mac_device = {
265 .name = "bfin_mac",
266 .dev.platform_data = &bfin_mii_bus,
267};
268#endif
269
270#if defined(CONFIG_MTD_M25P80) \
271 || defined(CONFIG_MTD_M25P80_MODULE)
272static struct mtd_partition bfin_spi_flash_partitions[] = {
273 {
274 .name = "bootloader(spi)",
275 .size = 0x00040000,
276 .offset = 0,
277 .mask_flags = MTD_CAP_ROM
278 }, {
279 .name = "linux kernel(spi)",
280 .size = MTDPART_SIZ_FULL,
281 .offset = MTDPART_OFS_APPEND,
282 }
283};
284
285static struct flash_platform_data bfin_spi_flash_data = {
286 .name = "m25p80",
287 .parts = bfin_spi_flash_partitions,
288 .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
289 .type = "m25p16",
290};
291
292/* SPI flash chip (m25p64) */
293static struct bfin5xx_spi_chip spi_flash_chip_info = {
294 .enable_dma = 0, /* use dma transfer with this chip*/
295 .bits_per_word = 8,
296};
297#endif
298
299#if defined(CONFIG_BFIN_SPI_ADC) \
300 || defined(CONFIG_BFIN_SPI_ADC_MODULE)
301/* SPI ADC chip */
302static struct bfin5xx_spi_chip spi_adc_chip_info = {
303 .enable_dma = 0, /* use dma transfer with this chip*/
304/*
305 * tll6527m V1.0 does not support native spi slave selects
306 * hence DMA mode will not be useful since the ADC needs
307 * CS to toggle for each sample and cs_change_per_word
308 * seems to be removed from spi_bfin5xx.c
309 */
310 .bits_per_word = 16,
311};
312#endif
313
314#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
315static struct bfin5xx_spi_chip mmc_spi_chip_info = {
316 .enable_dma = 0,
317 .bits_per_word = 8,
318};
319#endif
320
321#if defined(CONFIG_TOUCHSCREEN_AD7879) \
322 || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
323static const struct ad7879_platform_data bfin_ad7879_ts_info = {
324 .model = 7879, /* Model = AD7879 */
325 .x_plate_ohms = 620, /* 620 Ohm from the touch datasheet */
326 .pressure_max = 10000,
327 .pressure_min = 0,
328 .first_conversion_delay = 3,
329 /* wait 512us before do a first conversion */
330 .acquisition_time = 1, /* 4us acquisition time per sample */
331 .median = 2, /* do 8 measurements */
332 .averaging = 1,
333 /* take the average of 4 middle samples */
334 .pen_down_acc_interval = 255, /* 9.4 ms */
335 .gpio_export = 1, /* configure AUX as GPIO output*/
336 .gpio_base = LCD_BACKLIGHT_GPIO,
337};
338#endif
339
340#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
341 || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
342static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
343 .enable_dma = 0,
344 .bits_per_word = 16,
345};
346#endif
347
348#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
349static struct bfin5xx_spi_chip spidev_chip_info = {
350 .enable_dma = 0,
351 .bits_per_word = 8,
352};
353#endif
354
355#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
356static struct platform_device bfin_i2s = {
357 .name = "bfin-i2s",
358 .id = CONFIG_SND_BF5XX_SPORT_NUM,
359 /* TODO: add platform data here */
360};
361#endif
362
363#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
364static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
365 .enable_dma = 0,
366 .bits_per_word = 8,
367};
368#endif
369
370#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
371static struct bfin5xx_spi_chip spi_mcp23s08_sys_chip_info = {
372 .enable_dma = 0,
373 .bits_per_word = 8,
374};
375
376static struct bfin5xx_spi_chip spi_mcp23s08_usr_chip_info = {
377 .enable_dma = 0,
378 .bits_per_word = 8,
379};
380
381#include <linux/spi/mcp23s08.h>
382static const struct mcp23s08_platform_data bfin_mcp23s08_sys_gpio_info = {
383 .chip[0].is_present = true,
384 .base = 0x30,
385};
386static const struct mcp23s08_platform_data bfin_mcp23s08_usr_gpio_info = {
387 .chip[2].is_present = true,
388 .base = 0x38,
389};
390#endif
391
392static struct spi_board_info bfin_spi_board_info[] __initdata = {
393#if defined(CONFIG_MTD_M25P80) \
394 || defined(CONFIG_MTD_M25P80_MODULE)
395 {
396 /* the modalias must be the same as spi device driver name */
397 .modalias = "m25p80", /* Name of spi_driver for this device */
398 .max_speed_hz = 25000000,
399 /* max spi clock (SCK) speed in HZ */
400 .bus_num = 0, /* Framework bus number */
401 .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
402 /* Can be connected to TLL6527M GPIO connector */
403 /* Either SPI_ADC or M25P80 FLASH can be installed at a time */
404 .platform_data = &bfin_spi_flash_data,
405 .controller_data = &spi_flash_chip_info,
406 .mode = SPI_MODE_3,
407 },
408#endif
409
410#if defined(CONFIG_BFIN_SPI_ADC)
411 || defined(CONFIG_BFIN_SPI_ADC_MODULE)
412 {
413 .modalias = "bfin_spi_adc",
414 /* Name of spi_driver for this device */
415 .max_speed_hz = 10000000,
416 /* max spi clock (SCK) speed in HZ */
417 .bus_num = 0, /* Framework bus number */
418 .chip_select = EXP_GPIO_SPISEL_BASE + 0x04 + MAX_CTRL_CS,
419 /* Framework chip select. */
420 .platform_data = NULL, /* No spi_driver specific config */
421 .controller_data = &spi_adc_chip_info,
422 .mode = SPI_MODE_0,
423 },
424#endif
425
426#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
427 {
428 .modalias = "mmc_spi",
429/*
430 * TLL6527M V1.0 does not support SD Card at SPI Clock > 10 MHz due to
431 * SPI buffer limitations
432 */
433 .max_speed_hz = 10000000,
434 /* max spi clock (SCK) speed in HZ */
435 .bus_num = 0,
436 .chip_select = EXP_GPIO_SPISEL_BASE + 0x05 + MAX_CTRL_CS,
437 .controller_data = &mmc_spi_chip_info,
438 .mode = SPI_MODE_0,
439 },
440#endif
441#if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) \
442 || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
443 {
444 .modalias = "ad7879",
445 .platform_data = &bfin_ad7879_ts_info,
446 .irq = IRQ_PH14,
447 .max_speed_hz = 5000000,
448 /* max spi clock (SCK) speed in HZ */
449 .bus_num = 0,
450 .chip_select = EXP_GPIO_SPISEL_BASE + 0x07 + MAX_CTRL_CS,
451 .controller_data = &spi_ad7879_chip_info,
452 .mode = SPI_CPHA | SPI_CPOL,
453 },
454#endif
455#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
456 {
457 .modalias = "spidev",
458 .max_speed_hz = 10000000,
459 /* TLL6527Mv1-0 supports max spi clock (SCK) speed = 10 MHz */
460 .bus_num = 0,
461 .chip_select = EXP_GPIO_SPISEL_BASE + 0x03 + MAX_CTRL_CS,
462 .mode = SPI_CPHA | SPI_CPOL,
463 .controller_data = &spidev_chip_info,
464 },
465#endif
466#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
467 {
468 .modalias = "bfin-lq035q1-spi",
469 .max_speed_hz = 20000000,
470 .bus_num = 0,
471 .chip_select = EXP_GPIO_SPISEL_BASE + 0x06 + MAX_CTRL_CS,
472 .controller_data = &lq035q1_spi_chip_info,
473 .mode = SPI_CPHA | SPI_CPOL,
474 },
475#endif
476#if defined(CONFIG_GPIO_MCP23S08) || defined(CONFIG_GPIO_MCP23S08_MODULE)
477 {
478 .modalias = "mcp23s08",
479 .platform_data = &bfin_mcp23s08_sys_gpio_info,
480 .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
481 .bus_num = 0,
482 .chip_select = EXP_GPIO_SPISEL_BASE + 0x01 + MAX_CTRL_CS,
483 .controller_data = &spi_mcp23s08_sys_chip_info,
484 .mode = SPI_CPHA | SPI_CPOL,
485 },
486 {
487 .modalias = "mcp23s08",
488 .platform_data = &bfin_mcp23s08_usr_gpio_info,
489 .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
490 .bus_num = 0,
491 .chip_select = EXP_GPIO_SPISEL_BASE + 0x02 + MAX_CTRL_CS,
492 .controller_data = &spi_mcp23s08_usr_chip_info,
493 .mode = SPI_CPHA | SPI_CPOL,
494 },
495#endif
496};
497
498#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
499/* SPI controller data */
500static struct bfin5xx_spi_master bfin_spi0_info = {
501 .num_chipselect = EXP_GPIO_SPISEL_BASE + 8 + MAX_CTRL_CS,
502 /* EXP_GPIO_SPISEL_BASE will be > MAX_BLACKFIN_GPIOS */
503 .enable_dma = 1, /* master has the ability to do dma transfer */
504 .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
505};
506
507/* SPI (0) */
508static struct resource bfin_spi0_resource[] = {
509 [0] = {
510 .start = SPI0_REGBASE,
511 .end = SPI0_REGBASE + 0xFF,
512 .flags = IORESOURCE_MEM,
513 },
514 [1] = {
515 .start = CH_SPI,
516 .end = CH_SPI,
517 .flags = IORESOURCE_DMA,
518 },
519 [2] = {
520 .start = IRQ_SPI,
521 .end = IRQ_SPI,
522 .flags = IORESOURCE_IRQ,
523 },
524};
525
526static struct platform_device bfin_spi0_device = {
527 .name = "bfin-spi",
528 .id = 0, /* Bus number */
529 .num_resources = ARRAY_SIZE(bfin_spi0_resource),
530 .resource = bfin_spi0_resource,
531 .dev = {
532 .platform_data = &bfin_spi0_info, /* Passed to driver */
533 },
534};
535#endif /* spi master and devices */
536
537#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
538#ifdef CONFIG_SERIAL_BFIN_UART0
539static struct resource bfin_uart0_resources[] = {
540 {
541 .start = UART0_THR,
542 .end = UART0_GCTL+2,
543 .flags = IORESOURCE_MEM,
544 },
545 {
546 .start = IRQ_UART0_RX,
547 .end = IRQ_UART0_RX+1,
548 .flags = IORESOURCE_IRQ,
549 },
550 {
551 .start = IRQ_UART0_ERROR,
552 .end = IRQ_UART0_ERROR,
553 .flags = IORESOURCE_IRQ,
554 },
555 {
556 .start = CH_UART0_TX,
557 .end = CH_UART0_TX,
558 .flags = IORESOURCE_DMA,
559 },
560 {
561 .start = CH_UART0_RX,
562 .end = CH_UART0_RX,
563 .flags = IORESOURCE_DMA,
564 },
565};
566
567unsigned short bfin_uart0_peripherals[] = {
568 P_UART0_TX, P_UART0_RX, 0
569};
570
571static struct platform_device bfin_uart0_device = {
572 .name = "bfin-uart",
573 .id = 0,
574 .num_resources = ARRAY_SIZE(bfin_uart0_resources),
575 .resource = bfin_uart0_resources,
576 .dev = {
577 .platform_data = &bfin_uart0_peripherals,
578 /* Passed to driver */
579 },
580};
581#endif
582#ifdef CONFIG_SERIAL_BFIN_UART1
583static struct resource bfin_uart1_resources[] = {
584 {
585 .start = UART1_THR,
586 .end = UART1_GCTL+2,
587 .flags = IORESOURCE_MEM,
588 },
589 {
590 .start = IRQ_UART1_RX,
591 .end = IRQ_UART1_RX+1,
592 .flags = IORESOURCE_IRQ,
593 },
594 {
595 .start = IRQ_UART1_ERROR,
596 .end = IRQ_UART1_ERROR,
597 .flags = IORESOURCE_IRQ,
598 },
599 {
600 .start = CH_UART1_TX,
601 .end = CH_UART1_TX,
602 .flags = IORESOURCE_DMA,
603 },
604 {
605 .start = CH_UART1_RX,
606 .end = CH_UART1_RX,
607 .flags = IORESOURCE_DMA,
608 },
609#ifdef CONFIG_BFIN_UART1_CTSRTS
610 { /* CTS pin */
611 .start = GPIO_PF9,
612 .end = GPIO_PF9,
613 .flags = IORESOURCE_IO,
614 },
615 { /* RTS pin */
616 .start = GPIO_PF10,
617 .end = GPIO_PF10,
618 .flags = IORESOURCE_IO,
619 },
620#endif
621};
622
623unsigned short bfin_uart1_peripherals[] = {
624 P_UART1_TX, P_UART1_RX, 0
625};
626
627static struct platform_device bfin_uart1_device = {
628 .name = "bfin-uart",
629 .id = 1,
630 .num_resources = ARRAY_SIZE(bfin_uart1_resources),
631 .resource = bfin_uart1_resources,
632 .dev = {
633 .platform_data = &bfin_uart1_peripherals,
634 /* Passed to driver */
635 },
636};
637#endif
638#endif
639
640#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
641#ifdef CONFIG_BFIN_SIR0
642static struct resource bfin_sir0_resources[] = {
643 {
644 .start = 0xFFC00400,
645 .end = 0xFFC004FF,
646 .flags = IORESOURCE_MEM,
647 },
648 {
649 .start = IRQ_UART0_RX,
650 .end = IRQ_UART0_RX+1,
651 .flags = IORESOURCE_IRQ,
652 },
653 {
654 .start = CH_UART0_RX,
655 .end = CH_UART0_RX+1,
656 .flags = IORESOURCE_DMA,
657 },
658};
659
660static struct platform_device bfin_sir0_device = {
661 .name = "bfin_sir",
662 .id = 0,
663 .num_resources = ARRAY_SIZE(bfin_sir0_resources),
664 .resource = bfin_sir0_resources,
665};
666#endif
667#ifdef CONFIG_BFIN_SIR1
668static struct resource bfin_sir1_resources[] = {
669 {
670 .start = 0xFFC02000,
671 .end = 0xFFC020FF,
672 .flags = IORESOURCE_MEM,
673 },
674 {
675 .start = IRQ_UART1_RX,
676 .end = IRQ_UART1_RX+1,
677 .flags = IORESOURCE_IRQ,
678 },
679 {
680 .start = CH_UART1_RX,
681 .end = CH_UART1_RX+1,
682 .flags = IORESOURCE_DMA,
683 },
684};
685
686static struct platform_device bfin_sir1_device = {
687 .name = "bfin_sir",
688 .id = 1,
689 .num_resources = ARRAY_SIZE(bfin_sir1_resources),
690 .resource = bfin_sir1_resources,
691};
692#endif
693#endif
694
695#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
696static struct resource bfin_twi0_resource[] = {
697 [0] = {
698 .start = TWI0_REGBASE,
699 .end = TWI0_REGBASE,
700 .flags = IORESOURCE_MEM,
701 },
702 [1] = {
703 .start = IRQ_TWI,
704 .end = IRQ_TWI,
705 .flags = IORESOURCE_IRQ,
706 },
707};
708
709static struct platform_device i2c_bfin_twi_device = {
710 .name = "i2c-bfin-twi",
711 .id = 0,
712 .num_resources = ARRAY_SIZE(bfin_twi0_resource),
713 .resource = bfin_twi0_resource,
714};
715#endif
716
717static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
718#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
719 {
720 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
721 },
722#endif
723
724#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
725 {
726 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
727 },
728#endif
729#if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) \
730 || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
731 {
732 I2C_BOARD_INFO("ad7879", 0x2C),
733 .irq = IRQ_PH14,
734 .platform_data = (void *)&bfin_ad7879_ts_info,
735 },
736#endif
737#if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
738 {
739 I2C_BOARD_INFO("ssm2602", 0x1b),
740 },
741#endif
742 {
743 I2C_BOARD_INFO("adm1192", 0x2e),
744 },
745
746 {
747 I2C_BOARD_INFO("ltc3576", 0x09),
748 },
749#if defined(CONFIG_INPUT_ADXL34X_I2C) \
750 || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
751 {
752 I2C_BOARD_INFO("adxl34x", 0x53),
753 .irq = IRQ_PH13,
754 .platform_data = (void *)&adxl345_info,
755 },
756#endif
757};
758
759#if defined(CONFIG_SERIAL_BFIN_SPORT) \
760 || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
761#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
762static struct resource bfin_sport0_uart_resources[] = {
763 {
764 .start = SPORT0_TCR1,
765 .end = SPORT0_MRCS3+4,
766 .flags = IORESOURCE_MEM,
767 },
768 {
769 .start = IRQ_SPORT0_RX,
770 .end = IRQ_SPORT0_RX+1,
771 .flags = IORESOURCE_IRQ,
772 },
773 {
774 .start = IRQ_SPORT0_ERROR,
775 .end = IRQ_SPORT0_ERROR,
776 .flags = IORESOURCE_IRQ,
777 },
778};
779
780unsigned short bfin_sport0_peripherals[] = {
781 P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
782 P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
783};
784
785static struct platform_device bfin_sport0_uart_device = {
786 .name = "bfin-sport-uart",
787 .id = 0,
788 .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
789 .resource = bfin_sport0_uart_resources,
790 .dev = {
791 .platform_data = &bfin_sport0_peripherals,
792 /* Passed to driver */
793 },
794};
795#endif
796#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
797static struct resource bfin_sport1_uart_resources[] = {
798 {
799 .start = SPORT1_TCR1,
800 .end = SPORT1_MRCS3+4,
801 .flags = IORESOURCE_MEM,
802 },
803 {
804 .start = IRQ_SPORT1_RX,
805 .end = IRQ_SPORT1_RX+1,
806 .flags = IORESOURCE_IRQ,
807 },
808 {
809 .start = IRQ_SPORT1_ERROR,
810 .end = IRQ_SPORT1_ERROR,
811 .flags = IORESOURCE_IRQ,
812 },
813};
814
815unsigned short bfin_sport1_peripherals[] = {
816 P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
817 P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
818};
819
820static struct platform_device bfin_sport1_uart_device = {
821 .name = "bfin-sport-uart",
822 .id = 1,
823 .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
824 .resource = bfin_sport1_uart_resources,
825 .dev = {
826 .platform_data = &bfin_sport1_peripherals,
827 /* Passed to driver */
828 },
829};
830#endif
831#endif
832
833static const unsigned int cclk_vlev_datasheet[] = {
834 VRPAIR(VLEV_100, 400000000),
835 VRPAIR(VLEV_105, 426000000),
836 VRPAIR(VLEV_110, 500000000),
837 VRPAIR(VLEV_115, 533000000),
838 VRPAIR(VLEV_120, 600000000),
839};
840
841static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
842 .tuple_tab = cclk_vlev_datasheet,
843 .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
844 .vr_settling_time = 25 /* us */,
845};
846
847static struct platform_device bfin_dpmc = {
848 .name = "bfin dpmc",
849 .dev = {
850 .platform_data = &bfin_dmpc_vreg_data,
851 },
852};
853
854static struct platform_device *tll6527m_devices[] __initdata = {
855
856 &bfin_dpmc,
857
858#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
859 &rtc_device,
860#endif
861
862#if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
863 &musb_device,
864#endif
865
866#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
867 &bfin_mii_bus,
868 &bfin_mac_device,
869#endif
870
871#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
872 &bfin_spi0_device,
873#endif
874
875#if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
876 &bfin_lq035q1_device,
877#endif
878
879#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
880#ifdef CONFIG_SERIAL_BFIN_UART0
881 &bfin_uart0_device,
882#endif
883#ifdef CONFIG_SERIAL_BFIN_UART1
884 &bfin_uart1_device,
885#endif
886#endif
887
888#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
889#ifdef CONFIG_BFIN_SIR0
890 &bfin_sir0_device,
891#endif
892#ifdef CONFIG_BFIN_SIR1
893 &bfin_sir1_device,
894#endif
895#endif
896
897#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
898 &i2c_bfin_twi_device,
899#endif
900
901#if defined(CONFIG_SERIAL_BFIN_SPORT) \
902 || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
903#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
904 &bfin_sport0_uart_device,
905#endif
906#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
907 &bfin_sport1_uart_device,
908#endif
909#endif
910
911#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
912 &tll6527m_flash_device,
913#endif
914
915#if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
916 &bfin_i2s,
917#endif
918
919#if defined(CONFIG_GPIO_DECODER) || defined(CONFIG_GPIO_DECODER_MODULE)
920 &spi_decoded_gpio,
921#endif
922};
923
924static int __init tll6527m_init(void)
925{
926 printk(KERN_INFO "%s(): registering device resources\n", __func__);
927 i2c_register_board_info(0, bfin_i2c_board_info,
928 ARRAY_SIZE(bfin_i2c_board_info));
929 platform_add_devices(tll6527m_devices, ARRAY_SIZE(tll6527m_devices));
930 spi_register_board_info(bfin_spi_board_info,
931 ARRAY_SIZE(bfin_spi_board_info));
932 return 0;
933}
934
935arch_initcall(tll6527m_init);
936
937static struct platform_device *tll6527m_early_devices[] __initdata = {
938#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
939#ifdef CONFIG_SERIAL_BFIN_UART0
940 &bfin_uart0_device,
941#endif
942#ifdef CONFIG_SERIAL_BFIN_UART1
943 &bfin_uart1_device,
944#endif
945#endif
946
947#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
948#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
949 &bfin_sport0_uart_device,
950#endif
951#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
952 &bfin_sport1_uart_device,
953#endif
954#endif
955};
956
957void __init native_machine_early_platform_add_devices(void)
958{
959 printk(KERN_INFO "register early platform devices\n");
960 early_platform_add_devices(tll6527m_early_devices,
961 ARRAY_SIZE(tll6527m_early_devices));
962}
963
964void native_machine_restart(char *cmd)
965{
966 /* workaround reboot hang when booting from SPI */
967 if ((bfin_read_SYSCR() & 0x7) == 0x3)
968 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
969}
970
971void bfin_get_ether_addr(char *addr)
972{
973 /* the MAC is stored in OTP memory page 0xDF */
974 u32 ret;
975 u64 otp_mac;
976 u32 (*otp_read)(u32 page, u32 flags,
977 u64 *page_content) = (void *)0xEF00001A;
978
979 ret = otp_read(0xDF, 0x00, &otp_mac);
980 if (!(ret & 0x1)) {
981 char *otp_mac_p = (char *)&otp_mac;
982 for (ret = 0; ret < 6; ++ret)
983 addr[ret] = otp_mac_p[5 - ret];
984 }
985}
986EXPORT_SYMBOL(bfin_get_ether_addr);
generated by cgit v1.2.2 (git 2.25.0) at 2025-12-31 23:34:06 -0500