27 files changed, 579 insertions, 125 deletions
diff --git a/Documentation/hwmon/pcf8591 b/Documentation/hwmon/pcf8591
index 5628fcf4207f..e76a7892f68e 100644
--- a/Documentation/hwmon/pcf8591
+++ b/Documentation/hwmon/pcf8591
@@ -2,11 +2,11 @@ Kernel driver pcf8591
 =====================
 Supported chips:
-  * Philips PCF8591
+  * Philips/NXP PCF8591
    Prefix: 'pcf8591'
    Addresses scanned: I2C 0x48 - 0x4f
-    Datasheet: Publicly available at the Philips Semiconductor website
+    Datasheet: Publicly available at the NXP website
-               http://www.semiconductors.philips.com/pip/PCF8591P.html
+               http://www.nxp.com/pip/PCF8591_6.html
 Authors:
        Aurelien Jarno <aurelien@aurel32.net>
@@ -16,9 +16,10 @@ Authors:
 Description
 -----------
 The PCF8591 is an 8-bit A/D and D/A converter (4 analog inputs and one
-analog output) for the I2C bus produced by Philips Semiconductors. It
+analog output) for the I2C bus produced by Philips Semiconductors (now NXP).
-is designed to provide a byte I2C interface to up to 4 separate devices.
+It is designed to provide a byte I2C interface to up to 4 separate devices.
 The PCF8591 has 4 analog inputs programmable as single-ended or
 differential inputs :
@@ -58,8 +59,8 @@ Accessing PCF8591 via /sys interface
 -------------------------------------
 ! Be careful !
-The PCF8591 is plainly impossible to detect ! Stupid chip.
+The PCF8591 is plainly impossible to detect! Stupid chip.
-So every chip with address in the interval [48..4f] is
+So every chip with address in the interval [0x48..0x4f] is
 detected as PCF8591. If you have other chips in this address
 range, the workaround is to load this module after the one
 for your others chips.
@@ -67,19 +68,20 @@ for your others chips.
 On detection (i.e. insmod, modprobe et al.), directories are being
 created for each detected PCF8591:
-/sys/bus/devices/<0>-<1>/
+/sys/bus/i2c/devices/<0>-<1>/
 where <0> is the bus the chip was detected on (e. g. i2c-0)
 and <1> the chip address ([48..4f])
 Inside these directories, there are such files:
-in0, in1, in2, in3, out0_enable, out0_output, name
+in0_input, in1_input, in2_input, in3_input, out0_enable, out0_output, name
 Name contains chip name.
-The in0, in1, in2 and in3 files are RO. Reading gives the value of the
+The in0_input, in1_input, in2_input and in3_input files are RO. Reading gives
-corresponding channel. Depending on the current analog inputs configuration,
+the value of the corresponding channel. Depending on the current analog inputs
-files in2 and/or in3 do not exist. Values range are from 0 to 255 for single
+configuration, files in2_input and in3_input may not exist. Values range
-ended inputs and -128 to +127 for differential inputs (8-bit ADC).
+from 0 to 255 for single ended inputs and -128 to +127 for differential inputs
+(8-bit ADC).
 The out0_enable file is RW. Reading gives "1" for analog output enabled and
 "0" for analog output disabled. Writing accepts "0" and "1" accordingly.
diff --git a/Documentation/hwmon/tmp421 b/Documentation/hwmon/tmp421
new file mode 100644
index 000000000000..0cf07f824741
--- /dev/null
+++ b/Documentation/hwmon/tmp421
@@ -0,0 +1,36 @@
+Kernel driver tmp421
+====================
+Supported chips:
+  * Texas Instruments TMP421
+    Prefix: 'tmp421'
+    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+  * Texas Instruments TMP422
+    Prefix: 'tmp422'
+    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+  * Texas Instruments TMP423
+    Prefix: 'tmp423'
+    Addresses scanned: I2C 0x2a, 0x4c, 0x4d, 0x4e and 0x4f
+    Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp421.html
+Authors:
+        Andre Prendel <andre.prendel@gmx.de>
+Description
+-----------
+This driver implements support for Texas Instruments TMP421, TMP422
+and TMP423 temperature sensor chips. These chips implement one local
+and up to one (TMP421), up to two (TMP422) or up to three (TMP423)
+remote sensors. Temperature is measured in degrees Celsius. The chips
+are wired over I2C/SMBus and specified over a temperature range of -40
+to +125 degrees Celsius. Resolution for both the local and remote
+channels is 0.0625 degree C.
+The chips support only temperature measurement. The driver exports
+the temperature values via the following sysfs files:
+temp[1-4]_input
+temp[2-4]_fault
diff --git a/MAINTAINERS b/MAINTAINERS
index 9117b65f4ae3..c5f312bac7b4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -931,6 +931,12 @@ W:	http://wireless.kernel.org/en/users/Drivers/ar9170
 S:      Maintained
 F:      drivers/net/wireless/ath/ar9170/
+ATK0110 HWMON DRIVER
+M:      Luca Tettamanti <kronos.it@gmail.com>
+L:      lm-sensors@lm-sensors.org
+S:      Maintained
+F:      drivers/hwmon/asus_atk0110.c
 ATI_REMOTE2 DRIVER
 M:      Ville Syrjala <syrjala@sci.fi>
 S:      Maintained
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 2e25b7a827d3..461abb1e273a 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -28,6 +28,17 @@ config HWMON_VID
        tristate
        default n
+config HWMON_DEBUG_CHIP
+        bool "Hardware Monitoring Chip debugging messages"
+        default n
+        help
+          Say Y here if you want the I2C chip drivers to produce a bunch of
+          debug messages to the system log.  Select this if you are having
+          a problem with I2C support and want to see more of what is going
+          on.
+comment "Native drivers"
 config SENSORS_ABITUGURU
        tristate "Abit uGuru (rev 1 & 2)"
        depends on X86 && EXPERIMENTAL
@@ -248,18 +259,6 @@ config SENSORS_ASB100
          This driver can also be built as a module.  If so, the module
          will be called asb100.
-config SENSORS_ATK0110
-        tristate "ASUS ATK0110 ACPI hwmon"
-        depends on X86 && ACPI && EXPERIMENTAL
-        help
-          If you say yes here you get support for the ACPI hardware
-          monitoring interface found in many ASUS motherboards. This
-          driver will provide readings of fans, voltages and temperatures
-          through the system firmware.
-          This driver can also be built as a module. If so, the module
-          will be called asus_atk0110.
 config SENSORS_ATXP1
        tristate "Attansic ATXP1 VID controller"
        depends on I2C && EXPERIMENTAL
@@ -814,6 +813,16 @@ config SENSORS_TMP401
          This driver can also be built as a module.  If so, the module
          will be called tmp401.
+config SENSORS_TMP421
+        tristate "Texas Instruments TMP421 and compatible"
+        depends on I2C && EXPERIMENTAL
+        help
+          If you say yes here you get support for Texas Instruments TMP421,
+          TMP422 and TMP423 temperature sensor chips.
+          This driver can also be built as a module.  If so, the module
+          will be called tmp421.
 config SENSORS_VIA686A
        tristate "VIA686A"
        depends on PCI
@@ -964,34 +973,6 @@ config SENSORS_HDAPS
          Say Y here if you have an applicable laptop and want to experience
          the awesome power of hdaps.
-config SENSORS_LIS3LV02D
-        tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer"
-        depends on ACPI && INPUT
-        select INPUT_POLLDEV
-        select NEW_LEDS
-        select LEDS_CLASS
-        default n
-        help
-          This driver provides support for the LIS3LV02Dx accelerometer. In
-          particular, it can be found in a number of HP laptops, which have the
-          "Mobile Data Protection System 3D" or "3D DriveGuard" feature. On such
-          systems the driver should load automatically (via ACPI). The
-          accelerometer might also be found in other systems, connected via SPI
-          or I2C.  The accelerometer data is readable via
-          /sys/devices/platform/lis3lv02d.
-          This driver also provides an absolute input class device, allowing
-          the laptop to act as a pinball machine-esque joystick. On HP laptops,
-          if the led infrastructure is activated, support for a led indicating
-          disk protection will be provided as hp:red:hddprotection.
-          This driver can also be built as modules.  If so, the core module
-          will be called lis3lv02d and a specific module for HP laptops will be
-          called hp_accel.
-          Say Y here if you have an applicable laptop and want to experience
-          the awesome power of lis3lv02d.
 config SENSORS_LIS3_SPI
        tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer (SPI)"
        depends on !ACPI && SPI_MASTER && INPUT
@@ -1034,13 +1015,50 @@ config SENSORS_APPLESMC
          Say Y here if you have an applicable laptop and want to experience
          the awesome power of applesmc.
-config HWMON_DEBUG_CHIP
+if ACPI
-        bool "Hardware Monitoring Chip debugging messages"
+comment "ACPI drivers"
+config SENSORS_ATK0110
+        tristate "ASUS ATK0110"
+        depends on X86 && EXPERIMENTAL
+        help
+          If you say yes here you get support for the ACPI hardware
+          monitoring interface found in many ASUS motherboards. This
+          driver will provide readings of fans, voltages and temperatures
+          through the system firmware.
+          This driver can also be built as a module. If so, the module
+          will be called asus_atk0110.
+config SENSORS_LIS3LV02D
+        tristate "STMicroeletronics LIS3LV02Dx three-axis digital accelerometer"
+        depends on INPUT
+        select INPUT_POLLDEV
+        select NEW_LEDS
+        select LEDS_CLASS
        default n
        help
-          Say Y here if you want the I2C chip drivers to produce a bunch of
+          This driver provides support for the LIS3LV02Dx accelerometer. In
-          debug messages to the system log.  Select this if you are having
+          particular, it can be found in a number of HP laptops, which have the
-          a problem with I2C support and want to see more of what is going
+          "Mobile Data Protection System 3D" or "3D DriveGuard" feature. On such
-          on.
+          systems the driver should load automatically (via ACPI). The
+          accelerometer might also be found in other systems, connected via SPI
+          or I2C.  The accelerometer data is readable via
+          /sys/devices/platform/lis3lv02d.
+          This driver also provides an absolute input class device, allowing
+          the laptop to act as a pinball machine-esque joystick. On HP laptops,
+          if the led infrastructure is activated, support for a led indicating
+          disk protection will be provided as hp:red:hddprotection.
+          This driver can also be built as modules.  If so, the core module
+          will be called lis3lv02d and a specific module for HP laptops will be
+          called hp_accel.
+          Say Y here if you have an applicable laptop and want to experience
+          the awesome power of lis3lv02d.
+endif # ACPI
 endif # HWMON
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index 7f239a247c33..2e547881bc0a 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -5,6 +5,10 @@
 obj-$(CONFIG_HWMON)             += hwmon.o
 obj-$(CONFIG_HWMON_VID)         += hwmon-vid.o
+# APCI drivers
+obj-$(CONFIG_SENSORS_ATK0110)   += asus_atk0110.o
+# Native drivers
 # asb100, then w83781d go first, as they can override other drivers' addresses.
 obj-$(CONFIG_SENSORS_ASB100)    += asb100.o
 obj-$(CONFIG_SENSORS_W83627HF)  += w83627hf.o
@@ -29,10 +33,8 @@ obj-$(CONFIG_SENSORS_ADT7462)	+= adt7462.o
 obj-$(CONFIG_SENSORS_ADT7470)   += adt7470.o
 obj-$(CONFIG_SENSORS_ADT7473)   += adt7473.o
 obj-$(CONFIG_SENSORS_ADT7475)   += adt7475.o
 obj-$(CONFIG_SENSORS_APPLESMC)  += applesmc.o
 obj-$(CONFIG_SENSORS_AMS)       += ams/
-obj-$(CONFIG_SENSORS_ATK0110)   += asus_atk0110.o
 obj-$(CONFIG_SENSORS_ATXP1)     += atxp1.o
 obj-$(CONFIG_SENSORS_CORETEMP)  += coretemp.o
 obj-$(CONFIG_SENSORS_DME1737)   += dme1737.o
@@ -84,6 +86,7 @@ obj-$(CONFIG_SENSORS_SMSC47M1)	+= smsc47m1.o
 obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
 obj-$(CONFIG_SENSORS_THMC50)    += thmc50.o
 obj-$(CONFIG_SENSORS_TMP401)    += tmp401.o
+obj-$(CONFIG_SENSORS_TMP421)    += tmp421.o
 obj-$(CONFIG_SENSORS_VIA686A)   += via686a.o
 obj-$(CONFIG_SENSORS_VT1211)    += vt1211.o
 obj-$(CONFIG_SENSORS_VT8231)    += vt8231.o
diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c
index 4dbdb81ea3b1..03694cc17a32 100644
--- a/drivers/hwmon/abituguru.c
+++ b/drivers/hwmon/abituguru.c
@@ -32,7 +32,7 @@
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 #include <linux/dmi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 /* Banks */
 #define ABIT_UGURU_ALARM_BANK                   0x20 /* 1x 3 bytes */
diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c
index 7d3f15d32fdf..3cf28af614b5 100644
--- a/drivers/hwmon/abituguru3.c
+++ b/drivers/hwmon/abituguru3.c
@@ -34,7 +34,7 @@
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 #include <linux/dmi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 /* uGuru3 bank addresses */
 #define ABIT_UGURU3_SETTINGS_BANK               0x01
@@ -117,9 +117,12 @@ struct abituguru3_sensor_info {
        int offset;
 };
+/* Avoid use of flexible array members */
+#define ABIT_UGURU3_MAX_DMI_NAMES 2
 struct abituguru3_motherboard_info {
        u16 id;
-        const char *dmi_name;
+        const char *dmi_name[ABIT_UGURU3_MAX_DMI_NAMES + 1];
        /* + 1 -> end of sensors indicated by a sensor with name == NULL */
        struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1];
 };
@@ -164,7 +167,7 @@ struct abituguru3_data {
 /* Constants */
 static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
-        { 0x000C, NULL /* Unknown, need DMI string */, {
+        { 0x000C, { NULL } /* Unknown, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 10, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -186,7 +189,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX1 Fan",           35, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x000D, NULL /* Abit AW8, need DMI string */, {
+        { 0x000D, { NULL } /* Abit AW8, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 10, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -215,7 +218,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX5 Fan",           39, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x000E, NULL /* AL-8, need DMI string */, {
+        { 0x000E, { NULL } /* AL-8, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 10, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -236,7 +239,8 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "SYS Fan",            34, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x000F, NULL /* Unknown, need DMI string */, {
+        { 0x000F, { NULL } /* Unknown, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 10, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -257,7 +261,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "SYS Fan",            34, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0010, NULL /* Abit NI8 SLI GR, need DMI string */, {
+        { 0x0010, { NULL } /* Abit NI8 SLI GR, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 10, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -279,7 +283,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "OTES1 Fan",          36, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0011, "AT8 32X", {
+        { 0x0011, { "AT8 32X", NULL }, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 20, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -306,7 +310,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX3 Fan",           37, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0012, NULL /* Abit AN8 32X, need DMI string */, {
+        { 0x0012, { NULL } /* Abit AN8 32X, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 20, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -328,7 +332,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX1 Fan",           36, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0013, NULL /* Abit AW8D, need DMI string */, {
+        { 0x0013, { NULL } /* Abit AW8D, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 10, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -357,7 +361,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX5 Fan",           39, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0014, "AB9", /* + AB9 Pro */ {
+        { 0x0014, { "AB9", "AB9 Pro", NULL }, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 10, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -378,7 +382,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "SYS Fan",            34, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0015, NULL /* Unknown, need DMI string */, {
+        { 0x0015, { NULL } /* Unknown, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR",                 1, 0, 20, 1, 0 },
                { "DDR VTT",             2, 0, 10, 1, 0 },
@@ -402,7 +406,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX3 Fan",           36, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0016, "AW9D-MAX", {
+        { 0x0016, { "AW9D-MAX", NULL }, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR2",                1, 0, 20, 1, 0 },
                { "DDR2 VTT",            2, 0, 10, 1, 0 },
@@ -430,7 +434,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "OTES1 Fan",          38, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0017, NULL /* Unknown, need DMI string */, {
+        { 0x0017, { NULL } /* Unknown, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR2",                1, 0, 20, 1, 0 },
                { "DDR2 VTT",            2, 0, 10, 1, 0 },
@@ -455,7 +459,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX3 FAN",           37, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0018, "AB9 QuadGT", {
+        { 0x0018, { "AB9 QuadGT", NULL }, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR2",                1, 0, 20, 1, 0 },
                { "DDR2 VTT",            2, 0, 10, 1, 0 },
@@ -482,7 +486,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX3 Fan",           36, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0019, "IN9 32X MAX", {
+        { 0x0019, { "IN9 32X MAX", NULL }, {
                { "CPU Core",            7, 0, 10, 1, 0 },
                { "DDR2",               13, 0, 20, 1, 0 },
                { "DDR2 VTT",           14, 0, 10, 1, 0 },
@@ -509,7 +513,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX3 FAN",           36, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x001A, "IP35 Pro", {
+        { 0x001A, { "IP35 Pro", "IP35 Pro XE", NULL }, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR2",                1, 0, 20, 1, 0 },
                { "DDR2 VTT",            2, 0, 10, 1, 0 },
@@ -537,7 +541,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX4 Fan",           37, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x001B, NULL /* Unknown, need DMI string */, {
+        { 0x001B, { NULL } /* Unknown, need DMI string */, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR3",                1, 0, 20, 1, 0 },
                { "DDR3 VTT",            2, 0, 10, 1, 0 },
@@ -564,7 +568,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX3 Fan",           36, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x001C, "IX38 QuadGT", {
+        { 0x001C, { "IX38 QuadGT", NULL }, {
                { "CPU Core",            0, 0, 10, 1, 0 },
                { "DDR2",                1, 0, 20, 1, 0 },
                { "DDR2 VTT",            2, 0, 10, 1, 0 },
@@ -591,7 +595,7 @@ static const struct abituguru3_motherboard_info abituguru3_motherboards[] = {
                { "AUX3 Fan",           36, 2, 60, 1, 0 },
                { NULL, 0, 0, 0, 0, 0 } }
        },
-        { 0x0000, NULL, { { NULL, 0, 0, 0, 0, 0 } } }
+        { 0x0000, { NULL }, { { NULL, 0, 0, 0, 0, 0 } } }
 };
@@ -946,15 +950,6 @@ static int __devinit abituguru3_probe(struct platform_device *pdev)
        printk(KERN_INFO ABIT_UGURU3_NAME ": found Abit uGuru3, motherboard "
                "ID: %04X\n", (unsigned int)id);
-#ifdef CONFIG_DMI
-        if (!abituguru3_motherboards[i].dmi_name) {
-                printk(KERN_WARNING ABIT_UGURU3_NAME ": this motherboard was "
-                        "not detected using DMI. Please send the output of "
-                        "\"dmidecode\" to the abituguru3 maintainer "
-                        "(see MAINTAINERS)\n");
-        }
-#endif
        /* Fill the sysfs attr array */
        sysfs_attr_i = 0;
        sysfs_filename = data->sysfs_names;
@@ -1131,6 +1126,7 @@ static int __init abituguru3_dmi_detect(void)
 {
        const char *board_vendor, *board_name;
        int i, err = (force) ? 1 : -ENODEV;
+        const char *const *dmi_name;
        size_t sublen;
        board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR);
@@ -1151,17 +1147,17 @@ static int __init abituguru3_dmi_detect(void)
                sublen--;
        for (i = 0; abituguru3_motherboards[i].id; i++) {
-                const char *dmi_name = abituguru3_motherboards[i].dmi_name;
+                dmi_name = abituguru3_motherboards[i].dmi_name;
-                if (!dmi_name || strlen(dmi_name) != sublen)
+                for ( ; *dmi_name; dmi_name++) {
-                        continue;
+                        if (strlen(*dmi_name) != sublen)
-                if (!strncasecmp(board_name, dmi_name, sublen))
+                                continue;
-                        break;
+                        if (!strncasecmp(board_name, *dmi_name, sublen))
+                                return 0;
+                }
        }
-        if (!abituguru3_motherboards[i].id)
+        /* No match found */
-                return 1;
+        return 1;
-        return 0;
 }
 #else /* !CONFIG_DMI */
@@ -1221,6 +1217,13 @@ static int __init abituguru3_init(void)
                err = abituguru3_detect();
                if (err)
                        return err;
+#ifdef CONFIG_DMI
+                printk(KERN_WARNING ABIT_UGURU3_NAME ": this motherboard was "
+                        "not detected using DMI. Please send the output of "
+                        "\"dmidecode\" to the abituguru3 maintainer "
+                        "(see MAINTAINERS)\n");
+#endif
        }
        err = platform_driver_register(&abituguru3_driver);
diff --git a/drivers/hwmon/applesmc.c b/drivers/hwmon/applesmc.c
index 678e34b01e52..753b34885f9d 100644
--- a/drivers/hwmon/applesmc.c
+++ b/drivers/hwmon/applesmc.c
@@ -35,7 +35,7 @@
 #include <linux/dmi.h>
 #include <linux/mutex.h>
 #include <linux/hwmon-sysfs.h>
-#include <asm/io.h>
+#include <linux/io.h>
 #include <linux/leds.h>
 #include <linux/hwmon.h>
 #include <linux/workqueue.h>
diff --git a/drivers/hwmon/dme1737.c b/drivers/hwmon/dme1737.c
index 3df202a9ad72..9814d51b3af4 100644
--- a/drivers/hwmon/dme1737.c
+++ b/drivers/hwmon/dme1737.c
@@ -35,7 +35,7 @@
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 /* ISA device, if found */
 static struct platform_device *pdev;
diff --git a/drivers/hwmon/f71805f.c b/drivers/hwmon/f71805f.c
index 899876579253..525a00bd70b1 100644
--- a/drivers/hwmon/f71805f.c
+++ b/drivers/hwmon/f71805f.c
@@ -40,7 +40,7 @@
 #include <linux/sysfs.h>
 #include <linux/ioport.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 static unsigned short force_id;
 module_param(force_id, ushort, 0);
diff --git a/drivers/hwmon/hdaps.c b/drivers/hwmon/hdaps.c
index d3612a1f1981..be2d131e405c 100644
--- a/drivers/hwmon/hdaps.c
+++ b/drivers/hwmon/hdaps.c
@@ -35,8 +35,7 @@
 #include <linux/timer.h>
 #include <linux/dmi.h>
 #include <linux/jiffies.h>
+#include <linux/io.h>
-#include <asm/io.h>
 #define HDAPS_LOW_PORT          0x1600  /* first port used by hdaps */
 #define HDAPS_NR_PORTS          0x30    /* number of ports: 0x1600 - 0x162f */
diff --git a/drivers/hwmon/hwmon-vid.c b/drivers/hwmon/hwmon-vid.c
index bfc296145bba..bf0862a803c0 100644
--- a/drivers/hwmon/hwmon-vid.c
+++ b/drivers/hwmon/hwmon-vid.c
@@ -179,8 +179,14 @@ struct vrm_model {
 static struct vrm_model vrm_models[] = {
        {X86_VENDOR_AMD, 0x6, ANY, ANY, 90},            /* Athlon Duron etc */
        {X86_VENDOR_AMD, 0xF, 0x3F, ANY, 24},           /* Athlon 64, Opteron */
-        {X86_VENDOR_AMD, 0xF, ANY, ANY, 25},            /* NPT family 0Fh */
+        /* In theory, all NPT family 0Fh processors have 6 VID pins and should
+           thus use vrm 25, however in practice not all mainboards route the
+           6th VID pin because it is never needed. So we use the 5 VID pin
+           variant (vrm 24) for the models which exist today. */
+        {X86_VENDOR_AMD, 0xF, 0x7F, ANY, 24},           /* NPT family 0Fh */
+        {X86_VENDOR_AMD, 0xF, ANY, ANY, 25},            /* future fam. 0Fh */
        {X86_VENDOR_AMD, 0x10, ANY, ANY, 25},           /* NPT family 10h */
        {X86_VENDOR_INTEL, 0x6, 0x9, ANY, 13},          /* Pentium M (130 nm) */
        {X86_VENDOR_INTEL, 0x6, 0xB, ANY, 85},          /* Tualatin */
        {X86_VENDOR_INTEL, 0x6, 0xD, ANY, 13},          /* Pentium M (90 nm) */
@@ -191,12 +197,14 @@ static struct vrm_model vrm_models[] = {
        {X86_VENDOR_INTEL, 0xF, 0x1, ANY, 90},          /* P4 Willamette */
        {X86_VENDOR_INTEL, 0xF, 0x2, ANY, 90},          /* P4 Northwood */
        {X86_VENDOR_INTEL, 0xF, ANY, ANY, 100},         /* Prescott and above assume VRD 10 */
        {X86_VENDOR_CENTAUR, 0x6, 0x7, ANY, 85},        /* Eden ESP/Ezra */
        {X86_VENDOR_CENTAUR, 0x6, 0x8, 0x7, 85},        /* Ezra T */
        {X86_VENDOR_CENTAUR, 0x6, 0x9, 0x7, 85},        /* Nemiah */
        {X86_VENDOR_CENTAUR, 0x6, 0x9, ANY, 17},        /* C3-M, Eden-N */
        {X86_VENDOR_CENTAUR, 0x6, 0xA, 0x7, 0},         /* No information */
        {X86_VENDOR_CENTAUR, 0x6, 0xA, ANY, 13},        /* C7, Esther */
        {X86_VENDOR_UNKNOWN, ANY, ANY, ANY, 0}          /* stop here */
 };
diff --git a/drivers/hwmon/it87.c b/drivers/hwmon/it87.c
index 9157247fed8e..ffeb2a10e1a7 100644
--- a/drivers/hwmon/it87.c
+++ b/drivers/hwmon/it87.c
@@ -50,7 +50,7 @@
 #include <linux/string.h>
 #include <linux/dmi.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 #define DRVNAME "it87"
diff --git a/drivers/hwmon/lm78.c b/drivers/hwmon/lm78.c
index a1787fdf5b9f..f7e70163e016 100644
--- a/drivers/hwmon/lm78.c
+++ b/drivers/hwmon/lm78.c
@@ -31,7 +31,7 @@
 #include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/mutex.h>
-#include <asm/io.h>
+#include <linux/io.h>
 /* ISA device, if found */
 static struct platform_device *pdev;
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index b251d8674b41..6c53d987de10 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -75,6 +75,8 @@ I2C_CLIENT_INSMOD_7(lm85b, lm85c, adm1027, adt7463, adt7468, emc6d100,
 #define LM85_VERSTEP_GENERIC2           0x70
 #define LM85_VERSTEP_LM85C              0x60
 #define LM85_VERSTEP_LM85B              0x62
+#define LM85_VERSTEP_LM96000_1          0x68
+#define LM85_VERSTEP_LM96000_2          0x69
 #define LM85_VERSTEP_ADM1027            0x60
 #define LM85_VERSTEP_ADT7463            0x62
 #define LM85_VERSTEP_ADT7463C           0x6A
@@ -1133,6 +1135,26 @@ static void lm85_init_client(struct i2c_client *client)
                dev_warn(&client->dev, "Device is not ready\n");
 }
+static int lm85_is_fake(struct i2c_client *client)
+{
+        /*
+         * Differenciate between real LM96000 and Winbond WPCD377I. The latter
+         * emulate the former except that it has no hardware monitoring function
+         * so the readings are always 0.
+         */
+        int i;
+        u8 in_temp, fan;
+        for (i = 0; i < 8; i++) {
+                in_temp = i2c_smbus_read_byte_data(client, 0x20 + i);
+                fan = i2c_smbus_read_byte_data(client, 0x28 + i);
+                if (in_temp != 0x00 || fan != 0xff)
+                        return 0;
+        }
+        return 1;
+}
 /* Return 0 if detection is successful, -ENODEV otherwise */
 static int lm85_detect(struct i2c_client *client, int kind,
                       struct i2c_board_info *info)
@@ -1173,6 +1195,16 @@ static int lm85_detect(struct i2c_client *client, int kind,
                        case LM85_VERSTEP_LM85B:
                                kind = lm85b;
                                break;
+                        case LM85_VERSTEP_LM96000_1:
+                        case LM85_VERSTEP_LM96000_2:
+                                /* Check for Winbond WPCD377I */
+                                if (lm85_is_fake(client)) {
+                                        dev_dbg(&adapter->dev,
+                                                "Found Winbond WPCD377I, "
+                                                "ignoring\n");
+                                        return -ENODEV;
+                                }
+                                break;
                        }
                } else if (company == LM85_COMPANY_ANALOG_DEV) {
                        switch (verstep) {
diff --git a/drivers/hwmon/pc87360.c b/drivers/hwmon/pc87360.c
index fb052fea3744..4a64b85d4ec9 100644
--- a/drivers/hwmon/pc87360.c
+++ b/drivers/hwmon/pc87360.c
@@ -44,7 +44,7 @@
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 static u8 devid;
 static struct platform_device *pdev;
diff --git a/drivers/hwmon/pc87427.c b/drivers/hwmon/pc87427.c
index 3a8a0f7a7736..3170b26d2443 100644
--- a/drivers/hwmon/pc87427.c
+++ b/drivers/hwmon/pc87427.c
@@ -33,7 +33,7 @@
 #include <linux/sysfs.h>
 #include <linux/ioport.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 static unsigned short force_id;
 module_param(force_id, ushort, 0);
@@ -435,7 +435,7 @@ static int __devinit pc87427_probe(struct platform_device *pdev)
        /* This will need to be revisited when we add support for
           temperature and voltage monitoring. */
        res = platform_get_resource(pdev, IORESOURCE_IO, 0);
-        if (!request_region(res->start, res->end - res->start + 1, DRVNAME)) {
+        if (!request_region(res->start, resource_size(res), DRVNAME)) {
                err = -EBUSY;
                dev_err(&pdev->dev, "Failed to request region 0x%lx-0x%lx\n",
                        (unsigned long)res->start, (unsigned long)res->end);
@@ -475,7 +475,7 @@ exit_remove_files:
                sysfs_remove_group(&pdev->dev.kobj, &pc87427_group_fan[i]);
        }
 exit_release_region:
-        release_region(res->start, res->end - res->start + 1);
+        release_region(res->start, resource_size(res));
 exit_kfree:
        platform_set_drvdata(pdev, NULL);
        kfree(data);
@@ -500,7 +500,7 @@ static int __devexit pc87427_remove(struct platform_device *pdev)
        kfree(data);
        res = platform_get_resource(pdev, IORESOURCE_IO, 0);
-        release_region(res->start, res->end - res->start + 1);
+        release_region(res->start, resource_size(res));
        return 0;
 }
diff --git a/drivers/hwmon/sis5595.c b/drivers/hwmon/sis5595.c
index aa2e8318f167..12f2e7086560 100644
--- a/drivers/hwmon/sis5595.c
+++ b/drivers/hwmon/sis5595.c
@@ -63,7 +63,7 @@
 #include <linux/mutex.h>
 #include <linux/sysfs.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 /* If force_addr is set to anything different from 0, we forcibly enable
diff --git a/drivers/hwmon/smsc47b397.c b/drivers/hwmon/smsc47b397.c
index 6f6d52b4fb64..f46d936c12da 100644
--- a/drivers/hwmon/smsc47b397.c
+++ b/drivers/hwmon/smsc47b397.c
@@ -37,7 +37,7 @@
 #include <linux/init.h>
 #include <linux/mutex.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 static unsigned short force_id;
 module_param(force_id, ushort, 0);
diff --git a/drivers/hwmon/smsc47m1.c b/drivers/hwmon/smsc47m1.c
index ba75bfcf14ce..8ad50fdba00d 100644
--- a/drivers/hwmon/smsc47m1.c
+++ b/drivers/hwmon/smsc47m1.c
@@ -38,7 +38,7 @@
 #include <linux/mutex.h>
 #include <linux/sysfs.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 static unsigned short force_id;
 module_param(force_id, ushort, 0);
diff --git a/drivers/hwmon/tmp421.c b/drivers/hwmon/tmp421.c
new file mode 100644
index 000000000000..20924343431b
--- /dev/null
+++ b/drivers/hwmon/tmp421.c
@@ -0,0 +1,347 @@
+/* tmp421.c
+ *
+ * Copyright (C) 2009 Andre Prendel <andre.prendel@gmx.de>
+ * Preliminary support by:
+ * Melvin Rook, Raymond Ng
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+/*
+ * Driver for the Texas Instruments TMP421 SMBus temperature sensor IC.
+ * Supported models: TMP421, TMP422, TMP423
+ */
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+/* Addresses to scan */
+static unsigned short normal_i2c[] = { 0x2a, 0x4c, 0x4d, 0x4e, 0x4f,
+                                       I2C_CLIENT_END };
+/* Insmod parameters */
+I2C_CLIENT_INSMOD_3(tmp421, tmp422, tmp423);
+/* The TMP421 registers */
+#define TMP421_CONFIG_REG_1                     0x09
+#define TMP421_CONVERSION_RATE_REG              0x0B
+#define TMP421_MANUFACTURER_ID_REG              0xFE
+#define TMP421_DEVICE_ID_REG                    0xFF
+static const u8 TMP421_TEMP_MSB[4]              = { 0x00, 0x01, 0x02, 0x03 };
+static const u8 TMP421_TEMP_LSB[4]              = { 0x10, 0x11, 0x12, 0x13 };
+/* Flags */
+#define TMP421_CONFIG_SHUTDOWN                  0x40
+#define TMP421_CONFIG_RANGE                     0x04
+/* Manufacturer / Device ID's */
+#define TMP421_MANUFACTURER_ID                  0x55
+#define TMP421_DEVICE_ID                        0x21
+#define TMP422_DEVICE_ID                        0x22
+#define TMP423_DEVICE_ID                        0x23
+static const struct i2c_device_id tmp421_id[] = {
+        { "tmp421", tmp421 },
+        { "tmp422", tmp422 },
+        { "tmp423", tmp423 },
+        { }
+};
+MODULE_DEVICE_TABLE(i2c, tmp421_id);
+struct tmp421_data {
+        struct device *hwmon_dev;
+        struct mutex update_lock;
+        char valid;
+        unsigned long last_updated;
+        int kind;
+        u8 config;
+        s16 temp[4];
+};
+static int temp_from_s16(s16 reg)
+{
+        int temp = reg;
+        return (temp * 1000 + 128) / 256;
+}
+static int temp_from_u16(u16 reg)
+{
+        int temp = reg;
+        /* Add offset for extended temperature range. */
+        temp -= 64 * 256;
+        return (temp * 1000 + 128) / 256;
+}
+static struct tmp421_data *tmp421_update_device(struct device *dev)
+{
+        struct i2c_client *client = to_i2c_client(dev);
+        struct tmp421_data *data = i2c_get_clientdata(client);
+        int i;
+        mutex_lock(&data->update_lock);
+        if (time_after(jiffies, data->last_updated + 2 * HZ) || !data->valid) {
+                data->config = i2c_smbus_read_byte_data(client,
+                        TMP421_CONFIG_REG_1);
+                for (i = 0; i <= data->kind; i++) {
+                        data->temp[i] = i2c_smbus_read_byte_data(client,
+                                TMP421_TEMP_MSB[i]) << 8;
+                        data->temp[i] |= i2c_smbus_read_byte_data(client,
+                                TMP421_TEMP_LSB[i]);
+                }
+                data->last_updated = jiffies;
+                data->valid = 1;
+        }
+        mutex_unlock(&data->update_lock);
+        return data;
+}
+static ssize_t show_temp_value(struct device *dev,
+                               struct device_attribute *devattr, char *buf)
+{
+        int index = to_sensor_dev_attr(devattr)->index;
+        struct tmp421_data *data = tmp421_update_device(dev);
+        int temp;
+        mutex_lock(&data->update_lock);
+        if (data->config & TMP421_CONFIG_RANGE)
+                temp = temp_from_u16(data->temp[index]);
+        else
+                temp = temp_from_s16(data->temp[index]);
+        mutex_unlock(&data->update_lock);
+        return sprintf(buf, "%d\n", temp);
+}
+static ssize_t show_fault(struct device *dev,
+                          struct device_attribute *devattr, char *buf)
+{
+        int index = to_sensor_dev_attr(devattr)->index;
+        struct tmp421_data *data = tmp421_update_device(dev);
+        /*
+         * The OPEN bit signals a fault. This is bit 0 of the temperature
+         * register (low byte).
+         */
+        if (data->temp[index] & 0x01)
+                return sprintf(buf, "1\n");
+        else
+                return sprintf(buf, "0\n");
+}
+static mode_t tmp421_is_visible(struct kobject *kobj, struct attribute *a,
+                                int n)
+{
+        struct device *dev = container_of(kobj, struct device, kobj);
+        struct tmp421_data *data = dev_get_drvdata(dev);
+        struct device_attribute *devattr;
+        unsigned int index;
+        devattr = container_of(a, struct device_attribute, attr);
+        index = to_sensor_dev_attr(devattr)->index;
+        if (data->kind > index)
+                return a->mode;
+        return 0;
+}
+static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, show_temp_value, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_input, S_IRUGO, show_temp_value, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_fault, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp3_input, S_IRUGO, show_temp_value, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_fault, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp4_input, S_IRUGO, show_temp_value, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp4_fault, S_IRUGO, show_fault, NULL, 3);
+static struct attribute *tmp421_attr[] = {
+        &sensor_dev_attr_temp1_input.dev_attr.attr,
+        &sensor_dev_attr_temp2_input.dev_attr.attr,
+        &sensor_dev_attr_temp2_fault.dev_attr.attr,
+        &sensor_dev_attr_temp3_input.dev_attr.attr,
+        &sensor_dev_attr_temp3_fault.dev_attr.attr,
+        &sensor_dev_attr_temp4_input.dev_attr.attr,
+        &sensor_dev_attr_temp4_fault.dev_attr.attr,
+        NULL
+};
+static const struct attribute_group tmp421_group = {
+        .attrs = tmp421_attr,
+        .is_visible = tmp421_is_visible,
+};
+static int tmp421_init_client(struct i2c_client *client)
+{
+        int config, config_orig;
+        /* Set the conversion rate to 2 Hz */
+        i2c_smbus_write_byte_data(client, TMP421_CONVERSION_RATE_REG, 0x05);
+        /* Start conversions (disable shutdown if necessary) */
+        config = i2c_smbus_read_byte_data(client, TMP421_CONFIG_REG_1);
+        if (config < 0) {
+                dev_err(&client->dev, "Could not read configuration"
+                         " register (%d)\n", config);
+                return -ENODEV;
+        }
+        config_orig = config;
+        config &= ~TMP421_CONFIG_SHUTDOWN;
+        if (config != config_orig) {
+                dev_info(&client->dev, "Enable monitoring chip\n");
+                i2c_smbus_write_byte_data(client, TMP421_CONFIG_REG_1, config);
+        }
+        return 0;
+}
+static int tmp421_detect(struct i2c_client *client, int kind,
+                         struct i2c_board_info *info)
+{
+        struct i2c_adapter *adapter = client->adapter;
+        const char *names[] = { "TMP421", "TMP422", "TMP423" };
+        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+                return -ENODEV;
+        if (kind <= 0) {
+                u8 reg;
+                reg = i2c_smbus_read_byte_data(client,
+                                               TMP421_MANUFACTURER_ID_REG);
+                if (reg != TMP421_MANUFACTURER_ID)
+                        return -ENODEV;
+                reg = i2c_smbus_read_byte_data(client,
+                                               TMP421_DEVICE_ID_REG);
+                switch (reg) {
+                case TMP421_DEVICE_ID:
+                        kind = tmp421;
+                        break;
+                case TMP422_DEVICE_ID:
+                        kind = tmp422;
+                        break;
+                case TMP423_DEVICE_ID:
+                        kind = tmp423;
+                        break;
+                default:
+                        return -ENODEV;
+                }
+        }
+        strlcpy(info->type, tmp421_id[kind - 1].name, I2C_NAME_SIZE);
+        dev_info(&adapter->dev, "Detected TI %s chip at 0x%02x\n",
+                 names[kind - 1], client->addr);
+        return 0;
+}
+static int tmp421_probe(struct i2c_client *client,
+                        const struct i2c_device_id *id)
+{
+        struct tmp421_data *data;
+        int err;
+        data = kzalloc(sizeof(struct tmp421_data), GFP_KERNEL);
+        if (!data)
+                return -ENOMEM;
+        i2c_set_clientdata(client, data);
+        mutex_init(&data->update_lock);
+        data->kind = id->driver_data;
+        err = tmp421_init_client(client);
+        if (err)
+                goto exit_free;
+        err = sysfs_create_group(&client->dev.kobj, &tmp421_group);
+        if (err)
+                goto exit_free;
+        data->hwmon_dev = hwmon_device_register(&client->dev);
+        if (IS_ERR(data->hwmon_dev)) {
+                err = PTR_ERR(data->hwmon_dev);
+                data->hwmon_dev = NULL;
+                goto exit_remove;
+        }
+        return 0;
+exit_remove:
+        sysfs_remove_group(&client->dev.kobj, &tmp421_group);
+exit_free:
+        i2c_set_clientdata(client, NULL);
+        kfree(data);
+        return err;
+}
+static int tmp421_remove(struct i2c_client *client)
+{
+        struct tmp421_data *data = i2c_get_clientdata(client);
+        hwmon_device_unregister(data->hwmon_dev);
+        sysfs_remove_group(&client->dev.kobj, &tmp421_group);
+        i2c_set_clientdata(client, NULL);
+        kfree(data);
+        return 0;
+}
+static struct i2c_driver tmp421_driver = {
+        .class = I2C_CLASS_HWMON,
+        .driver = {
+                .name   = "tmp421",
+        },
+        .probe = tmp421_probe,
+        .remove = tmp421_remove,
+        .id_table = tmp421_id,
+        .detect = tmp421_detect,
+        .address_data = &addr_data,
+};
+static int __init tmp421_init(void)
+{
+        return i2c_add_driver(&tmp421_driver);
+}
+static void __exit tmp421_exit(void)
+{
+        i2c_del_driver(&tmp421_driver);
+}
+MODULE_AUTHOR("Andre Prendel <andre.prendel@gmx.de>");
+MODULE_DESCRIPTION("Texas Instruments TMP421/422/423 temperature sensor"
+                   " driver");
+MODULE_LICENSE("GPL");
+module_init(tmp421_init);
+module_exit(tmp421_exit);
diff --git a/drivers/hwmon/via686a.c b/drivers/hwmon/via686a.c
index a022aedcaacb..39e82a492f26 100644
--- a/drivers/hwmon/via686a.c
+++ b/drivers/hwmon/via686a.c
@@ -42,7 +42,7 @@
 #include <linux/mutex.h>
 #include <linux/sysfs.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 /* If force_addr is set to anything different from 0, we forcibly enable
diff --git a/drivers/hwmon/vt1211.c b/drivers/hwmon/vt1211.c
index 73f77a9b8b18..ae33bbb577c7 100644
--- a/drivers/hwmon/vt1211.c
+++ b/drivers/hwmon/vt1211.c
@@ -33,7 +33,7 @@
 #include <linux/mutex.h>
 #include <linux/ioport.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 static int uch_config = -1;
 module_param(uch_config, int, 0);
@@ -1136,7 +1136,7 @@ static int __devinit vt1211_probe(struct platform_device *pdev)
        }
        res = platform_get_resource(pdev, IORESOURCE_IO, 0);
-        if (!request_region(res->start, res->end - res->start + 1, DRVNAME)) {
+        if (!request_region(res->start, resource_size(res), DRVNAME)) {
                err = -EBUSY;
                dev_err(dev, "Failed to request region 0x%lx-0x%lx\n",
                        (unsigned long)res->start, (unsigned long)res->end);
@@ -1209,7 +1209,7 @@ EXIT_DEV_REMOVE:
        dev_err(dev, "Sysfs interface creation failed (%d)\n", err);
 EXIT_DEV_REMOVE_SILENT:
        vt1211_remove_sysfs(pdev);
-        release_region(res->start, res->end - res->start + 1);
+        release_region(res->start, resource_size(res));
 EXIT_KFREE:
        platform_set_drvdata(pdev, NULL);
        kfree(data);
@@ -1228,7 +1228,7 @@ static int __devexit vt1211_remove(struct platform_device *pdev)
        kfree(data);
        res = platform_get_resource(pdev, IORESOURCE_IO, 0);
-        release_region(res->start, res->end - res->start + 1);
+        release_region(res->start, resource_size(res));
        return 0;
 }
diff --git a/drivers/hwmon/vt8231.c b/drivers/hwmon/vt8231.c
index 9982b45fbb14..470a1226ba2b 100644
--- a/drivers/hwmon/vt8231.c
+++ b/drivers/hwmon/vt8231.c
@@ -36,7 +36,7 @@
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 static int force_addr;
 module_param(force_addr, int, 0);
diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c
index 0e9746913d2b..bb5e78748783 100644
--- a/drivers/hwmon/w83627ehf.c
+++ b/drivers/hwmon/w83627ehf.c
@@ -51,7 +51,7 @@
 #include <linux/err.h>
 #include <linux/mutex.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 #include "lm75.h"
 enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg };
diff --git a/drivers/hwmon/w83627hf.c b/drivers/hwmon/w83627hf.c
index 389150ba30d3..2be28ac4ede0 100644
--- a/drivers/hwmon/w83627hf.c
+++ b/drivers/hwmon/w83627hf.c
@@ -51,7 +51,7 @@
 #include <linux/mutex.h>
 #include <linux/ioport.h>
 #include <linux/acpi.h>
-#include <asm/io.h>
+#include <linux/io.h>
 #include "lm75.h"
 static struct platform_device *pdev;
diff --git a/drivers/hwmon/w83781d.c b/drivers/hwmon/w83781d.c
index 0bdab959b736..d27ed1bac002 100644
--- a/drivers/hwmon/w83781d.c
+++ b/drivers/hwmon/w83781d.c
@@ -48,7 +48,7 @@
 #ifdef CONFIG_ISA
 #include <linux/platform_device.h>
 #include <linux/ioport.h>
-#include <asm/io.h>
+#include <linux/io.h>
 #endif
 #include "lm75.h"