41 files changed, 484 insertions, 989 deletions

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index aa0e0c9f74c5..8982c0932438 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -1074,22 +1074,6 @@ endif
 config BLK_DEV_IDEDMA
         def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 
-config IDEDMA_IVB
-        bool "IGNORE word93 Validation BITS"
-        depends on BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS
-        ---help---
-          There are unclear terms in ATA-4 and ATA-5 standards how certain
-          hardware (an 80c ribbon) should be detected. Different interpretations
-          of the standards have been released in hardware. This causes problems:
-          for example, a host with Ultra Mode 4 (or higher) will not run
-          in that mode with an 80c ribbon.
-
-          If you are experiencing compatibility or performance problems, you
-          MAY try to answer Y here. However, it does not necessarily solve
-          any of your problems, it could even cause more of them.
-
-          It is normally safe to answer Y; however, the default is N.
-
 endif
 
 config BLK_DEV_HD_ONLY
diff --git a/drivers/ide/arm/icside.c b/drivers/ide/arm/icside.c
index 7912a471f10d..bd1f5b670378 100644
--- a/drivers/ide/arm/icside.c
+++ b/drivers/ide/arm/icside.c
@@ -248,7 +248,7 @@ static void icside_build_sglist(ide_drive_t *drive, struct request *rq)
  *      MW1     80      50      50      150     C
  *      MW2     70      25      25      120     C
  */
-static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
+static void icside_set_dma_mode(ide_drive_t *drive, const u8 xfer_mode)
 {
         int cycle_time, use_dma_info = 0;
 
@@ -273,7 +273,7 @@ static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
                 cycle_time = 480;
                 break;
         default:
-                return 1;
+                return;
         }
 
         /*
@@ -287,8 +287,6 @@ static int icside_set_speed(ide_drive_t *drive, const u8 xfer_mode)
 
         printk("%s: %s selected (peak %dMB/s)\n", drive->name,
                 ide_xfer_verbose(xfer_mode), 2000 / drive->drive_data);
-
-        return ide_config_drive_speed(drive, xfer_mode);
 }
 
 static void icside_dma_host_off(ide_drive_t *drive)
@@ -313,41 +311,10 @@ static int icside_dma_on(ide_drive_t *drive)
 
 static int icside_dma_check(ide_drive_t *drive)
 {
-        struct hd_driveid *id = drive->id;
-        ide_hwif_t *hwif = HWIF(drive);
-        int xfer_mode = 0;
-
-        if (!(id->capability & 1) || !hwif->autodma)
-                goto out;
-
-        /*
-         * Consult the list of known "bad" drives
-         */
-        if (__ide_dma_bad_drive(drive))
-                goto out;
-
-        /*
-         * Enable DMA on any drive that has multiword DMA
-         */
-        if (id->field_valid & 2) {
-                xfer_mode = ide_max_dma_mode(drive);
-                goto out;
-        }
-
-        /*
-         * Consult the list of known "good" drives
-         */
-        if (__ide_dma_good_drive(drive)) {
-                if (id->eide_dma_time > 150)
-                        goto out;
-                xfer_mode = XFER_MW_DMA_1;
-        }
-
-out:
-        if (xfer_mode == 0)
-                return -1;
+        if (ide_tune_dma(drive))
+                return 0;
 
-        return icside_set_speed(drive, xfer_mode) ? -1 : 0;
+        return -1;
 }
 
 static int icside_dma_end(ide_drive_t *drive)
@@ -464,7 +431,7 @@ static void icside_dma_init(ide_hwif_t *hwif)
 
         hwif->dmatable_cpu      = NULL;
         hwif->dmatable_dma      = 0;
-        hwif->speedproc         = icside_set_speed;
+        hwif->set_dma_mode      = icside_set_dma_mode;
         hwif->autodma           = 1;
 
         hwif->ide_dma_check     = icside_dma_check;
diff --git a/drivers/ide/cris/ide-cris.c b/drivers/ide/cris/ide-cris.c
index 4bb42b30bfc0..2b4d2a0ae5c2 100644
--- a/drivers/ide/cris/ide-cris.c
+++ b/drivers/ide/cris/ide-cris.c
@@ -716,11 +716,9 @@ static void cris_set_pio_mode(ide_drive_t *drive, const u8 pio)
         }
 
         cris_ide_set_speed(TYPE_PIO, setup, strobe, hold);
-
-        (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }
 
-static int speed_cris_ide(ide_drive_t *drive, const u8 speed)
+static void cris_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         int cyc = 0, dvs = 0, strobe = 0, hold = 0;
 
@@ -759,8 +757,6 @@ static int speed_cris_ide(ide_drive_t *drive, const u8 speed)
                 cris_ide_set_speed(TYPE_UDMA, cyc, dvs, 0);
         else
                 cris_ide_set_speed(TYPE_DMA, 0, strobe, hold);
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 void __init
@@ -791,7 +787,7 @@ init_e100_ide (void)
                 hwif->mmio = 1;
                 hwif->chipset = ide_etrax100;
                 hwif->set_pio_mode = &cris_set_pio_mode;
-                hwif->speedproc = &speed_cris_ide;
+                hwif->set_dma_mode = &cris_set_dma_mode;
                 hwif->ata_input_data = &cris_ide_input_data;
                 hwif->ata_output_data = &cris_ide_output_data;
                 hwif->atapi_input_bytes = &cris_atapi_input_bytes;
diff --git a/drivers/ide/ide-acpi.c b/drivers/ide/ide-acpi.c
index 6bff81a58bf3..1d5f6823101c 100644
--- a/drivers/ide/ide-acpi.c
+++ b/drivers/ide/ide-acpi.c
@@ -649,7 +649,6 @@ void ide_acpi_set_state(ide_hwif_t *hwif, int on)
         if (!on)
                 acpi_bus_set_power(hwif->acpidata->obj_handle, ACPI_STATE_D3);
 }
-EXPORT_SYMBOL_GPL(ide_acpi_set_state);
 
 /**
  * ide_acpi_init - initialize the ACPI link for an IDE interface
diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c
index 6000c08f51ba..b453211ee0fc 100644
--- a/drivers/ide/ide-dma.c
+++ b/drivers/ide/ide-dma.c
@@ -169,6 +169,11 @@ ide_startstop_t ide_dma_intr (ide_drive_t *drive)
 
 EXPORT_SYMBOL_GPL(ide_dma_intr);
 
+static int ide_dma_good_drive(ide_drive_t *drive)
+{
+        return ide_in_drive_list(drive->id, drive_whitelist);
+}
+
 #ifdef CONFIG_BLK_DEV_IDEDMA_PCI
 /**
  *      ide_build_sglist        -       map IDE scatter gather for DMA I/O
@@ -357,7 +362,7 @@ static int config_drive_for_dma (ide_drive_t *drive)
                                 return 0;
 
                 /* Consult the list of known "good" drives */
-                if (__ide_dma_good_drive(drive))
+                if (ide_dma_good_drive(drive))
                         return 0;
         }
 
@@ -639,14 +644,6 @@ int __ide_dma_bad_drive (ide_drive_t *drive)
 
 EXPORT_SYMBOL(__ide_dma_bad_drive);
 
-int __ide_dma_good_drive (ide_drive_t *drive)
-{
-        struct hd_driveid *id = drive->id;
-        return ide_in_drive_list(id, drive_whitelist);
-}
-
-EXPORT_SYMBOL(__ide_dma_good_drive);
-
 static const u8 xfer_mode_bases[] = {
         XFER_UDMA_0,
         XFER_MW_DMA_0,
@@ -746,6 +743,14 @@ u8 ide_find_dma_mode(ide_drive_t *drive, u8 req_mode)
                 }
         }
 
+        if (hwif->chipset == ide_acorn && mode == 0) {
+                /*
+                 * is this correct?
+                 */
+                if (ide_dma_good_drive(drive) && drive->id->eide_dma_time < 150)
+                        mode = XFER_MW_DMA_1;
+        }
+
         printk(KERN_DEBUG "%s: selected mode 0x%x\n", drive->name, mode);
 
         return min(mode, req_mode);
@@ -769,7 +774,10 @@ int ide_tune_dma(ide_drive_t *drive)
         if (!speed)
                 return 0;
 
-        if (drive->hwif->speedproc(drive, speed))
+        if (drive->hwif->host_flags & IDE_HFLAG_NO_SET_MODE)
+                return 0;
+
+        if (ide_set_dma_mode(drive, speed))
                 return 0;
 
         return 1;
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 9560a8f4a86c..4cece930114c 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -836,9 +836,17 @@ static ide_startstop_t do_special (ide_drive_t *drive)
                 if (set_pio_mode_abuse(drive->hwif, req_pio)) {
                         if (hwif->set_pio_mode)
                                 hwif->set_pio_mode(drive, req_pio);
-                } else
+                } else {
+                        int keep_dma = drive->using_dma;
+
                         ide_set_pio(drive, req_pio);
 
+                        if (hwif->host_flags & IDE_HFLAG_SET_PIO_MODE_KEEP_DMA) {
+                                if (keep_dma)
+                                        hwif->ide_dma_on(drive);
+                        }
+                }
+
                 return ide_stopped;
         } else {
                 if (drive->media == ide_disk)
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index cf0678b61161..aa738833bed5 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -473,57 +473,22 @@ int drive_is_ready (ide_drive_t *drive)
 EXPORT_SYMBOL(drive_is_ready);
 
 /*
- * Global for All, and taken from ide-pmac.c. Can be called
- * with spinlock held & IRQs disabled, so don't schedule !
- */
-int wait_for_ready (ide_drive_t *drive, int timeout)
-{
-        ide_hwif_t *hwif        = HWIF(drive);
-        u8 stat                 = 0;
-
-        while(--timeout) {
-                stat = hwif->INB(IDE_STATUS_REG);
-                if (!(stat & BUSY_STAT)) {
-                        if (drive->ready_stat == 0)
-                                break;
-                        else if ((stat & drive->ready_stat)||(stat & ERR_STAT))
-                                break;
-                }
-                mdelay(1);
-        }
-        if ((stat & ERR_STAT) || timeout <= 0) {
-                if (stat & ERR_STAT) {
-                        printk(KERN_ERR "%s: wait_for_ready, "
-                                "error status: %x\n", drive->name, stat);
-                }
-                return 1;
-        }
-        return 0;
-}
-
-/*
  * This routine busy-waits for the drive status to be not "busy".
  * It then checks the status for all of the "good" bits and none
  * of the "bad" bits, and if all is okay it returns 0.  All other
- * cases return 1 after invoking ide_error() -- caller should just return.
+ * cases return error -- caller may then invoke ide_error().
  *
  * This routine should get fixed to not hog the cpu during extra long waits..
  * That could be done by busy-waiting for the first jiffy or two, and then
  * setting a timer to wake up at half second intervals thereafter,
  * until timeout is achieved, before timing out.
  */
-int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout)
+static int __ide_wait_stat(ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout, u8 *rstat)
 {
-        ide_hwif_t *hwif = HWIF(drive);
-        u8 stat;
-        int i;
+        ide_hwif_t *hwif = drive->hwif;
         unsigned long flags;
- 
-        /* bail early if we've exceeded max_failures */
-        if (drive->max_failures && (drive->failures > drive->max_failures)) {
-                *startstop = ide_stopped;
-                return 1;
-        }
+        int i;
+        u8 stat;
 
         udelay(1);      /* spec allows drive 400ns to assert "BUSY" */
         if ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
@@ -541,8 +506,8 @@ int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 b
                                         break;
 
                                 local_irq_restore(flags);
-                                *startstop = ide_error(drive, "status timeout", stat);
-                                return 1;
+                                *rstat = stat;
+                                return -EBUSY;
                         }
                 }
                 local_irq_restore(flags);
@@ -556,11 +521,39 @@ int ide_wait_stat (ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 b
          */
         for (i = 0; i < 10; i++) {
                 udelay(1);
-                if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), good, bad))
+                if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), good, bad)) {
+                        *rstat = stat;
                         return 0;
+                }
         }
-        *startstop = ide_error(drive, "status error", stat);
-        return 1;
+        *rstat = stat;
+        return -EFAULT;
+}
+
+/*
+ * In case of error returns error value after doing "*startstop = ide_error()".
+ * The caller should return the updated value of "startstop" in this case,
+ * "startstop" is unchanged when the function returns 0.
+ */
+int ide_wait_stat(ide_startstop_t *startstop, ide_drive_t *drive, u8 good, u8 bad, unsigned long timeout)
+{
+        int err;
+        u8 stat;
+
+        /* bail early if we've exceeded max_failures */
+        if (drive->max_failures && (drive->failures > drive->max_failures)) {
+                *startstop = ide_stopped;
+                return 1;
+        }
+
+        err = __ide_wait_stat(drive, good, bad, timeout, &stat);
+
+        if (err) {
+                char *s = (err == -EBUSY) ? "status timeout" : "status error";
+                *startstop = ide_error(drive, s, stat);
+        }
+
+        return err;
 }
 
 EXPORT_SYMBOL(ide_wait_stat);
@@ -620,15 +613,10 @@ u8 eighty_ninty_three (ide_drive_t *drive)
 
         /*
          * FIXME:
-         * - change master/slave IDENTIFY order
          * - force bit13 (80c cable present) check also for !ivb devices
          *   (unless the slave device is pre-ATA3)
          */
-#ifndef CONFIG_IDEDMA_IVB
         if ((id->hw_config & 0x4000) || (ivb && (id->hw_config & 0x2000)))
-#else
-        if (id->hw_config & 0x6000)
-#endif
                 return 1;
 
 no_80w:
@@ -778,15 +766,10 @@ int ide_driveid_update (ide_drive_t *drive)
 #endif
 }
 
-/*
- * Similar to ide_wait_stat(), except it never calls ide_error internally.
- *
- * const char *msg == consider adding for verbose errors.
- */
-int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
+int ide_config_drive_speed(ide_drive_t *drive, u8 speed)
 {
-        ide_hwif_t *hwif        = HWIF(drive);
-        int     i, error        = 1;
+        ide_hwif_t *hwif = drive->hwif;
+        int error;
         u8 stat;
 
 //      while (HWGROUP(drive)->busy)
@@ -826,35 +809,10 @@ int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
         hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
         if ((IDE_CONTROL_REG) && (drive->quirk_list == 2))
                 hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
-        udelay(1);
-        /*
-         * Wait for drive to become non-BUSY
-         */
-        if ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
-                unsigned long flags, timeout;
-                local_irq_set(flags);
-                timeout = jiffies + WAIT_CMD;
-                while ((stat = hwif->INB(IDE_STATUS_REG)) & BUSY_STAT) {
-                        if (time_after(jiffies, timeout))
-                                break;
-                }
-                local_irq_restore(flags);
-        }
 
-        /*
-         * Allow status to settle, then read it again.
-         * A few rare drives vastly violate the 400ns spec here,
-         * so we'll wait up to 10usec for a "good" status
-         * rather than expensively fail things immediately.
-         * This fix courtesy of Matthew Faupel & Niccolo Rigacci.
-         */
-        for (i = 0; i < 10; i++) {
-                udelay(1);
-                if (OK_STAT((stat = hwif->INB(IDE_STATUS_REG)), drive->ready_stat, BUSY_STAT|DRQ_STAT|ERR_STAT)) {
-                        error = 0;
-                        break;
-                }
-        }
+        error = __ide_wait_stat(drive, drive->ready_stat,
+                                BUSY_STAT|DRQ_STAT|ERR_STAT,
+                                WAIT_CMD, &stat);
 
         SELECT_MASK(drive, 0);
 
@@ -899,9 +857,6 @@ int ide_config_drive_speed (ide_drive_t *drive, u8 speed)
         return error;
 }
 
-EXPORT_SYMBOL(ide_config_drive_speed);
-
-
 /*
  * This should get invoked any time we exit the driver to
  * wait for an interrupt response from a drive.  handler() points
diff --git a/drivers/ide/ide-lib.c b/drivers/ide/ide-lib.c
index d97390c0543b..0e2562f0f74e 100644
--- a/drivers/ide/ide-lib.c
+++ b/drivers/ide/ide-lib.c
@@ -349,7 +349,7 @@ void ide_set_pio(ide_drive_t *drive, u8 req_pio)
                           drive->name, host_pio, req_pio,
                           req_pio == 255 ? "(auto-tune)" : "", pio);
 
-        hwif->set_pio_mode(drive, pio);
+        (void)ide_set_pio_mode(drive, XFER_PIO_0 + pio);
 }
 
 EXPORT_SYMBOL_GPL(ide_set_pio);
@@ -378,39 +378,83 @@ void ide_toggle_bounce(ide_drive_t *drive, int on)
                 blk_queue_bounce_limit(drive->queue, addr);
 }
 
+int ide_set_pio_mode(ide_drive_t *drive, const u8 mode)
+{
+        ide_hwif_t *hwif = drive->hwif;
+
+        if (hwif->set_pio_mode == NULL)
+                return -1;
+
+        /*
+         * TODO: temporary hack for some legacy host drivers that didn't
+         * set transfer mode on the device in ->set_pio_mode method...
+         */
+        if (hwif->set_dma_mode == NULL) {
+                hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+                return 0;
+        }
+
+        if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
+                if (ide_config_drive_speed(drive, mode))
+                        return -1;
+                hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+                return 0;
+        } else {
+                hwif->set_pio_mode(drive, mode - XFER_PIO_0);
+                return ide_config_drive_speed(drive, mode);
+        }
+}
+
+int ide_set_dma_mode(ide_drive_t *drive, const u8 mode)
+{
+        ide_hwif_t *hwif = drive->hwif;
+
+        if (hwif->set_dma_mode == NULL)
+                return -1;
+
+        if (hwif->host_flags & IDE_HFLAG_POST_SET_MODE) {
+                if (ide_config_drive_speed(drive, mode))
+                        return -1;
+                hwif->set_dma_mode(drive, mode);
+                return 0;
+        } else {
+                hwif->set_dma_mode(drive, mode);
+                return ide_config_drive_speed(drive, mode);
+        }
+}
+
+EXPORT_SYMBOL_GPL(ide_set_dma_mode);
+
 /**
  *      ide_set_xfer_rate       -       set transfer rate
  *      @drive: drive to set
- *      @speed: speed to attempt to set
+ *      @rate: speed to attempt to set
  *      
  *      General helper for setting the speed of an IDE device. This
  *      function knows about user enforced limits from the configuration
- *      which speedproc() does not.  High level drivers should never
- *      invoke speedproc() directly.
+ *      which ->set_pio_mode/->set_dma_mode does not.
  */
- 
+
 int ide_set_xfer_rate(ide_drive_t *drive, u8 rate)
 {
         ide_hwif_t *hwif = drive->hwif;
 
-        if (hwif->speedproc == NULL)
+        if (hwif->set_dma_mode == NULL)
                 return -1;
 
         rate = ide_rate_filter(drive, rate);
 
-        if (rate >= XFER_PIO_0 && rate <= XFER_PIO_5) {
-                if (hwif->set_pio_mode)
-                        hwif->set_pio_mode(drive, rate - XFER_PIO_0);
+        if (rate >= XFER_PIO_0 && rate <= XFER_PIO_5)
+                return ide_set_pio_mode(drive, rate);
 
-                /*
-                 * FIXME: this is incorrect to return zero here but
-                 * since all users of ide_set_xfer_rate() ignore
-                 * the return value it is not a problem currently
-                 */
-                return 0;
-        }
+        /*
+         * TODO: transfer modes 0x00-0x07 passed from the user-space are
+         * currently handled here which needs fixing (please note that such
+         * case could happen iff the transfer mode has already been set on
+         * the device by ide-proc.c::set_xfer_rate()).
+         */
 
-        return hwif->speedproc(drive, rate);
+        return ide_set_dma_mode(drive, rate);
 }
 
 static void ide_dump_opcode(ide_drive_t *drive)
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index b4c9f63a3854..d1011712601c 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -719,9 +719,9 @@ EXPORT_SYMBOL_GPL(ide_undecoded_slave);
  */
 static void probe_hwif(ide_hwif_t *hwif, void (*fixup)(ide_hwif_t *hwif))
 {
-        unsigned int unit;
         unsigned long flags;
         unsigned int irqd;
+        int unit;
 
         if (hwif->noprobe)
                 return;
@@ -777,10 +777,9 @@ static void probe_hwif(ide_hwif_t *hwif, void (*fixup)(ide_hwif_t *hwif))
                 printk(KERN_DEBUG "%s: Wait for ready failed before probe !\n", hwif->name);
 
         /*
-         * Second drive should only exist if first drive was found,
-         * but a lot of cdrom drives are configured as single slaves.
+         * Need to probe slave device first to make it release PDIAG-.
          */
-        for (unit = 0; unit < MAX_DRIVES; ++unit) {
+        for (unit = MAX_DRIVES - 1; unit >= 0; unit--) {
                 ide_drive_t *drive = &hwif->drives[unit];
                 drive->dn = (hwif->channel ? 2 : 0) + unit;
                 (void) probe_for_drive(drive);
diff --git a/drivers/ide/ide.c b/drivers/ide/ide.c
index a96a8b1b3539..5c0e4078b5cb 100644
--- a/drivers/ide/ide.c
+++ b/drivers/ide/ide.c
@@ -397,7 +397,7 @@ static void ide_hwif_restore(ide_hwif_t *hwif, ide_hwif_t *tmp_hwif)
 #endif
 
         hwif->set_pio_mode              = tmp_hwif->set_pio_mode;
-        hwif->speedproc                 = tmp_hwif->speedproc;
+        hwif->set_dma_mode              = tmp_hwif->set_dma_mode;
         hwif->mdma_filter               = tmp_hwif->mdma_filter;
         hwif->udma_filter               = tmp_hwif->udma_filter;
         hwif->selectproc                = tmp_hwif->selectproc;
diff --git a/drivers/ide/legacy/ide_platform.c b/drivers/ide/legacy/ide_platform.c
index ccfb9893a467..b992b2b91fe2 100644
--- a/drivers/ide/legacy/ide_platform.c
+++ b/drivers/ide/legacy/ide_platform.c
@@ -65,7 +65,7 @@ found:
         hwif->hw.irq = hwif->irq = irq;
 
         hwif->hw.dma = NO_DMA;
-        hwif->hw.chipset = ide_generic;
+        hwif->chipset = hwif->hw.chipset = ide_generic;
 
         if (mmio) {
                 hwif->mmio = 1;
diff --git a/drivers/ide/mips/au1xxx-ide.c b/drivers/ide/mips/au1xxx-ide.c
index 85819ae20602..aebde49365d1 100644
--- a/drivers/ide/mips/au1xxx-ide.c
+++ b/drivers/ide/mips/au1xxx-ide.c
@@ -101,12 +101,7 @@ void auide_outsw(unsigned long port, void *addr, u32 count)
 
 static void au1xxx_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        int mem_sttime;
-        int mem_stcfg;
-        u8 speed;
-
-        mem_sttime = 0;
-        mem_stcfg  = au_readl(MEM_STCFG2);
+        int mem_sttime = 0, mem_stcfg = au_readl(MEM_STCFG2);
 
         /* set pio mode! */
         switch(pio) {
@@ -164,18 +159,11 @@ static void au1xxx_set_pio_mode(ide_drive_t *drive, const u8 pio)
 
         au_writel(mem_sttime,MEM_STTIME2);
         au_writel(mem_stcfg,MEM_STCFG2);
-
-        speed = pio + XFER_PIO_0;
-        ide_config_drive_speed(drive, speed);
 }
 
-static int auide_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void auide_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
-        int mem_sttime;
-        int mem_stcfg;
-
-        mem_sttime = 0;
-        mem_stcfg  = au_readl(MEM_STCFG2);
+        int mem_sttime = 0, mem_stcfg = au_readl(MEM_STCFG2);
 
         switch(speed) {
 #ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
@@ -211,16 +199,11 @@ static int auide_tune_chipset(ide_drive_t *drive, const u8 speed)
                 break;
 #endif
         default:
-                return 1;
+                return;
         }
 
-        if (ide_config_drive_speed(drive, speed))
-                return 1;
-
         au_writel(mem_sttime,MEM_STTIME2);
         au_writel(mem_stcfg,MEM_STCFG2);
-
-        return 0;
 }
 
 /*
@@ -682,6 +665,7 @@ static int au_ide_probe(struct device *dev)
 #endif
 
         hwif->pio_mask = ATA_PIO4;
+        hwif->host_flags = IDE_HFLAG_POST_SET_MODE;
 
         hwif->noprobe = 0;
         hwif->drives[0].unmask          = 1;
@@ -702,7 +686,7 @@ static int au_ide_probe(struct device *dev)
 #endif
 
         hwif->set_pio_mode              = &au1xxx_set_pio_mode;
-        hwif->speedproc                 = &auide_tune_chipset;
+        hwif->set_dma_mode              = &auide_set_dma_mode;
 
 #ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
         hwif->dma_off_quietly           = &auide_dma_off_quietly;
diff --git a/drivers/ide/pci/aec62xx.c b/drivers/ide/pci/aec62xx.c
index 0d5f62c5dfae..d6cb2d5143c8 100644
--- a/drivers/ide/pci/aec62xx.c
+++ b/drivers/ide/pci/aec62xx.c
@@ -87,7 +87,7 @@ static u8 pci_bus_clock_list_ultra (u8 speed, struct chipset_bus_clock_list_entr
         return chipset_table->ultra_settings;
 }
 
-static int aec6210_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void aec6210_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -111,10 +111,9 @@ static int aec6210_tune_chipset(ide_drive_t *drive, const u8 speed)
         tmp2 = ((ultra_conf << (2*drive->dn)) | (tmp1 & ~(3 << (2*drive->dn))));
         pci_write_config_byte(dev, 0x54, tmp2);
         local_irq_restore(flags);
-        return(ide_config_drive_speed(drive, speed));
 }
 
-static int aec6260_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void aec6260_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -135,12 +134,11 @@ static int aec6260_tune_chipset(ide_drive_t *drive, const u8 speed)
         tmp2 = ((ultra_conf << (4*unit)) | (tmp1 & ~(7 << (4*unit))));
         pci_write_config_byte(dev, (0x44|hwif->channel), tmp2);
         local_irq_restore(flags);
-        return(ide_config_drive_speed(drive, speed));
 }
 
 static void aec_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        (void) HWIF(drive)->speedproc(drive, pio + XFER_PIO_0);
+        drive->hwif->set_dma_mode(drive, pio + XFER_PIO_0);
 }
 
 static int aec62xx_config_drive_xfer_rate (ide_drive_t *drive)
@@ -205,9 +203,9 @@ static void __devinit init_hwif_aec62xx(ide_hwif_t *hwif)
         if (dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) {
                 if(hwif->mate)
                         hwif->mate->serialized = hwif->serialized = 1;
-                hwif->speedproc = &aec6210_tune_chipset;
+                hwif->set_dma_mode = &aec6210_set_mode;
         } else
-                hwif->speedproc = &aec6260_tune_chipset;
+                hwif->set_dma_mode = &aec6260_set_mode;
 
         if (!hwif->dma_base) {
                 hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/alim15x3.c b/drivers/ide/pci/alim15x3.c
index d04b966b4347..0b83443bf250 100644
--- a/drivers/ide/pci/alim15x3.c
+++ b/drivers/ide/pci/alim15x3.c
@@ -283,14 +283,14 @@ static int ali_get_info (char *buffer, char **addr, off_t offset, int count)
 #endif  /* defined(DISPLAY_ALI_TIMINGS) && defined(CONFIG_IDE_PROC_FS) */
 
 /**
- *      ali_tune_pio    -       set host controller for PIO mode
+ *      ali_set_pio_mode        -       set host controller for PIO mode
  *      @drive: drive
  *      @pio: PIO mode number
  *
  *      Program the controller for the given PIO mode.
  */
 
-static void ali_tune_pio(ide_drive_t *drive, const u8 pio)
+static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         ide_hwif_t *hwif = HWIF(drive);
         struct pci_dev *dev = hwif->pci_dev;
@@ -358,21 +358,6 @@ static void ali_tune_pio(ide_drive_t *drive, const u8 pio)
 }
 
 /**
- *      ali_set_pio_mode        -       set up drive for PIO mode
- *      @drive: drive to tune
- *      @pio: desired mode
- *
- *      Program the controller with the desired PIO timing for the given drive.
- *      Then set up the drive itself.
- */
-
-static void ali_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        ali_tune_pio(drive, pio);
-        (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-/**
  *      ali_udma_filter         -       compute UDMA mask
  *      @drive: IDE device
  *
@@ -401,15 +386,14 @@ static u8 ali_udma_filter(ide_drive_t *drive)
 }
 
 /**
- *      ali15x3_tune_chipset    -       set up chipset/drive for new speed
- *      @drive: drive to configure for
- *      @speed: desired speed
+ *      ali_set_dma_mode        -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
  *      Configure the hardware for the desired IDE transfer mode.
- *      We also do the needed drive configuration through helpers
  */
 
-static int ali15x3_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void ali_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -419,7 +403,7 @@ static int ali15x3_tune_chipset(ide_drive_t *drive, const u8 speed)
         int m5229_udma          = (hwif->channel) ? 0x57 : 0x56;
 
         if (speed < XFER_PIO_0)
-                return 1;
+                return;
 
         if (speed == XFER_UDMA_6)
                 speed1 = 0x47;
@@ -450,7 +434,6 @@ static int ali15x3_tune_chipset(ide_drive_t *drive, const u8 speed)
                         pci_write_config_byte(dev, 0x4b, tmpbyte);
                 }
         }
-        return (ide_config_drive_speed(drive, speed));
 }
 
 /**
@@ -699,7 +682,7 @@ static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
 {
         hwif->autodma = 0;
         hwif->set_pio_mode = &ali_set_pio_mode;
-        hwif->speedproc = &ali15x3_tune_chipset;
+        hwif->set_dma_mode = &ali_set_dma_mode;
         hwif->udma_filter = &ali_udma_filter;
 
         /* don't use LBA48 DMA on ALi devices before rev 0xC5 */
@@ -711,6 +694,10 @@ static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
                 return;
         }
 
+        /*
+         * check in ->init_dma guarantees m5229_revision >= 0x20 here
+         */
+
         if (m5229_revision > 0x20)
                 hwif->atapi_dma = 1;
 
@@ -728,18 +715,15 @@ static void __devinit init_hwif_common_ali15x3 (ide_hwif_t *hwif)
         hwif->mwdma_mask = 0x07;
         hwif->swdma_mask = 0x07;
 
-        if (m5229_revision >= 0x20) {
-                /*
-                 * M1543C or newer for DMAing
-                 */
-                hwif->ide_dma_check = &ali15x3_config_drive_for_dma;
-                hwif->dma_setup = &ali15x3_dma_setup;
-                if (!noautodma)
-                        hwif->autodma = 1;
-
-                if (hwif->cbl != ATA_CBL_PATA40_SHORT)
-                        hwif->cbl = ata66_ali15x3(hwif);
-        }
+        hwif->ide_dma_check = &ali15x3_config_drive_for_dma;
+        hwif->dma_setup = &ali15x3_dma_setup;
+
+        if (hwif->cbl != ATA_CBL_PATA40_SHORT)
+                hwif->cbl = ata66_ali15x3(hwif);
+
+        if (!noautodma)
+                hwif->autodma = 1;
+
         hwif->drives[0].autodma = hwif->autodma;
         hwif->drives[1].autodma = hwif->autodma;
 }
diff --git a/drivers/ide/pci/amd74xx.c b/drivers/ide/pci/amd74xx.c
index 513205e52ad2..6ff4089a2379 100644
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -1,5 +1,5 @@
 /*
- * Version 2.22
+ * Version 2.23
  *
  * AMD 755/756/766/8111 and nVidia nForce/2/2s/3/3s/CK804/MCP04
  * IDE driver for Linux.
@@ -229,20 +229,16 @@ static void amd_set_speed(struct pci_dev *dev, unsigned char dn, struct ide_timi
 }
 
 /*
- * amd_set_drive() computes timing values configures the drive and
- * the chipset to a desired transfer mode. It also can be called
- * by upper layers.
+ * amd_set_drive() computes timing values and configures the chipset
+ * to a desired transfer mode.  It also can be called by upper layers.
  */
 
-static int amd_set_drive(ide_drive_t *drive, const u8 speed)
+static void amd_set_drive(ide_drive_t *drive, const u8 speed)
 {
         ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1);
         struct ide_timing t, p;
         int T, UT;
 
-        if (speed != XFER_PIO_SLOW)
-                ide_config_drive_speed(drive, speed);
-
         T = 1000000000 / amd_clock;
         UT = (amd_config->udma_mask == ATA_UDMA2) ? T : (T / 2);
 
@@ -257,12 +253,6 @@ static int amd_set_drive(ide_drive_t *drive, const u8 speed)
         if (speed == XFER_UDMA_6 && amd_clock <= 33333) t.udma = 15;
 
         amd_set_speed(HWIF(drive)->pci_dev, drive->dn, &t);
-
-        if (!drive->init_speed) 
-                drive->init_speed = speed;
-        drive->current_speed = speed;
-
-        return 0;
 }
 
 /*
@@ -399,7 +389,7 @@ static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif)
         hwif->autodma = 0;
 
         hwif->set_pio_mode = &amd_set_pio_mode;
-        hwif->speedproc = &amd_set_drive;
+        hwif->set_dma_mode = &amd_set_drive;
 
         for (i = 0; i < 2; i++) {
                 hwif->drives[i].io_32bit = 1;
@@ -441,7 +431,8 @@ static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif)
                 .enablebits     = {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, \
                 .bootable       = ON_BOARD,                             \
                 .host_flags     = IDE_HFLAG_PIO_NO_BLACKLIST            \
-                                | IDE_HFLAG_PIO_NO_DOWNGRADE,           \
+                                | IDE_HFLAG_PIO_NO_DOWNGRADE            \
+                                | IDE_HFLAG_POST_SET_MODE,              \
                 .pio_mask       = ATA_PIO5,                             \
         }
 
@@ -454,7 +445,8 @@ static void __devinit init_hwif_amd74xx(ide_hwif_t *hwif)
                 .enablebits     = {{0x50,0x02,0x02}, {0x50,0x01,0x01}}, \
                 .bootable       = ON_BOARD,                             \
                 .host_flags     = IDE_HFLAG_PIO_NO_BLACKLIST            \
-                                | IDE_HFLAG_PIO_NO_DOWNGRADE,           \
+                                | IDE_HFLAG_PIO_NO_DOWNGRADE            \
+                                | IDE_HFLAG_POST_SET_MODE,              \
                 .pio_mask       = ATA_PIO5,                             \
         }
 
diff --git a/drivers/ide/pci/atiixp.c b/drivers/ide/pci/atiixp.c
index 178876a3afca..0eb97f021d39 100644
--- a/drivers/ide/pci/atiixp.c
+++ b/drivers/ide/pci/atiixp.c
@@ -122,14 +122,14 @@ static void atiixp_dma_host_off(ide_drive_t *drive)
 }
 
 /**
- *      atiixp_tune_pio -       tune a drive attached to a ATIIXP
- *      @drive: drive to tune
- *      @pio: desired PIO mode
+ *      atiixp_set_pio_mode     -       set host controller for PIO mode
+ *      @drive: drive
+ *      @pio: PIO mode number
  *
  *      Set the interface PIO mode.
  */
 
-static void atiixp_tune_pio(ide_drive_t *drive, u8 pio)
+static void atiixp_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         struct pci_dev *dev = drive->hwif->pci_dev;
         unsigned long flags;
@@ -153,23 +153,16 @@ static void atiixp_tune_pio(ide_drive_t *drive, u8 pio)
         spin_unlock_irqrestore(&atiixp_lock, flags);
 }
 
-static void atiixp_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        atiixp_tune_pio(drive, pio);
-        (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
 /**
- *      atiixp_tune_chipset     -       tune a ATIIXP interface
- *      @drive: IDE drive to tune
- *      @speed: speed to configure
+ *      atiixp_set_dma_mode     -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
- *      Set a ATIIXP interface channel to the desired speeds. This involves
- *      requires the right timing data into the ATIIXP configuration space
- *      then setting the drive parameters appropriately
+ *      Set a ATIIXP host controller to the desired DMA mode.  This involves
+ *      programming the right timing data into the PCI configuration space.
  */
 
-static int atiixp_speedproc(ide_drive_t *drive, const u8 speed)
+static void atiixp_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         struct pci_dev *dev = drive->hwif->pci_dev;
         unsigned long flags;
@@ -204,9 +197,7 @@ static int atiixp_speedproc(ide_drive_t *drive, const u8 speed)
         else
                 pio = speed - XFER_PIO_0;
 
-        atiixp_tune_pio(drive, pio);
-
-        return ide_config_drive_speed(drive, speed);
+        atiixp_set_pio_mode(drive, pio);
 }
 
 /**
@@ -249,7 +240,7 @@ static void __devinit init_hwif_atiixp(ide_hwif_t *hwif)
 
         hwif->autodma = 0;
         hwif->set_pio_mode = &atiixp_set_pio_mode;
-        hwif->speedproc = &atiixp_speedproc;
+        hwif->set_dma_mode = &atiixp_set_dma_mode;
         hwif->drives[0].autotune = 1;
         hwif->drives[1].autotune = 1;
 
diff --git a/drivers/ide/pci/cmd64x.c b/drivers/ide/pci/cmd64x.c
index 0b568c60f926..d50f15e34b80 100644
--- a/drivers/ide/pci/cmd64x.c
+++ b/drivers/ide/pci/cmd64x.c
@@ -280,10 +280,9 @@ static void cmd64x_set_pio_mode(ide_drive_t *drive, const u8 pio)
                 return;
 
         cmd64x_tune_pio(drive, pio);
-        (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }
 
-static int cmd64x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void cmd64x_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -324,13 +323,11 @@ static int cmd64x_tune_chipset(ide_drive_t *drive, const u8 speed)
                 program_cycle_times(drive, 480, 215);
                 break;
         default:
-                return 1;
+                return;
         }
 
         if (speed >= XFER_SW_DMA_0)
                 (void) pci_write_config_byte(dev, pciU, regU);
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 static int cmd64x_config_drive_for_dma (ide_drive_t *drive)
@@ -524,7 +521,7 @@ static void __devinit init_hwif_cmd64x(ide_hwif_t *hwif)
         pci_read_config_byte(dev, PCI_REVISION_ID, &rev);
 
         hwif->set_pio_mode = &cmd64x_set_pio_mode;
-        hwif->speedproc = &cmd64x_tune_chipset;
+        hwif->set_dma_mode = &cmd64x_set_dma_mode;
 
         hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
 
diff --git a/drivers/ide/pci/cs5520.c b/drivers/ide/pci/cs5520.c
index 1217d2a747fb..fbce90048aec 100644
--- a/drivers/ide/pci/cs5520.c
+++ b/drivers/ide/pci/cs5520.c
@@ -96,22 +96,13 @@ static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
         reg = inb(hwif->dma_base + 0x02 + 8*controller);
         reg |= 1<<((drive->dn&1)+5);
         outb(reg, hwif->dma_base + 0x02 + 8*controller);
-
-        (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }
 
-static int cs5520_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void cs5520_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         printk(KERN_ERR "cs55x0: bad ide timing.\n");
 
         cs5520_set_pio_mode(drive, 0);
-
-        /*
-         * FIXME: this is incorrect to return zero here but
-         * since all users of ide_set_xfer_rate() ignore
-         * the return value it is not a problem currently
-         */
-        return 0;
 }
 
 static int cs5520_config_drive_xfer_rate(ide_drive_t *drive)
@@ -150,26 +141,25 @@ static int cs5520_dma_on(ide_drive_t *drive)
 static void __devinit init_hwif_cs5520(ide_hwif_t *hwif)
 {
         hwif->set_pio_mode = &cs5520_set_pio_mode;
-        hwif->speedproc = &cs5520_tune_chipset;
-        hwif->ide_dma_check = &cs5520_config_drive_xfer_rate;
-        hwif->ide_dma_on = &cs5520_dma_on;
+        hwif->set_dma_mode = &cs5520_set_dma_mode;
 
-        if(!noautodma)
-                hwif->autodma = 1;
-        
-        if(!hwif->dma_base)
-        {
-                hwif->drives[0].autotune = 1;
-                hwif->drives[1].autotune = 1;
+        if (hwif->dma_base == 0) {
+                hwif->drives[1].autotune = hwif->drives[0].autotune = 1;
                 return;
         }
 
+        hwif->ide_dma_check = &cs5520_config_drive_xfer_rate;
+        hwif->ide_dma_on = &cs5520_dma_on;
+
         /* ATAPI is harder so leave it for now */
         hwif->atapi_dma = 0;
         hwif->ultra_mask = 0;
         hwif->swdma_mask = 0;
         hwif->mwdma_mask = 0;
-        
+
+        if (!noautodma)
+                hwif->autodma = 1;
+
         hwif->drives[0].autodma = hwif->autodma;
         hwif->drives[1].autodma = hwif->autodma;
 }
diff --git a/drivers/ide/pci/cs5530.c b/drivers/ide/pci/cs5530.c
index 741507b4cd93..e4121577cef0 100644
--- a/drivers/ide/pci/cs5530.c
+++ b/drivers/ide/pci/cs5530.c
@@ -30,22 +30,6 @@
 #include <asm/io.h>
 #include <asm/irq.h>
 
-/**
- *      cs5530_xfer_set_mode    -       set a new transfer mode at the drive
- *      @drive: drive to tune
- *      @mode: new mode
- *
- *      Logging wrapper to the IDE driver speed configuration. This can
- *      probably go away now.
- */
- 
-static int cs5530_set_xfer_mode (ide_drive_t *drive, u8 mode)
-{
-        printk(KERN_DEBUG "%s: cs5530_set_xfer_mode(%s)\n",
-                drive->name, ide_xfer_verbose(mode));
-        return (ide_config_drive_speed(drive, mode));
-}
-
 /*
  * Here are the standard PIO mode 0-4 timings for each "format".
  * Format-0 uses fast data reg timings, with slower command reg timings.
@@ -62,20 +46,12 @@ static unsigned int cs5530_pio_timings[2][5] = {
 #define CS5530_BAD_PIO(timings) (((timings)&~0x80000000)==0x0000e132)
 #define CS5530_BASEREG(hwif)    (((hwif)->dma_base & ~0xf) + ((hwif)->channel ? 0x30 : 0x20))
 
-static void cs5530_tunepio(ide_drive_t *drive, u8 pio)
-{
-        unsigned long basereg = CS5530_BASEREG(drive->hwif);
-        unsigned int format = (inl(basereg + 4) >> 31) & 1;
-
-        outl(cs5530_pio_timings[format][pio], basereg + ((drive->dn & 1)<<3));
-}
-
 /**
- *      cs5530_set_pio_mode     -       set PIO mode
+ *      cs5530_set_pio_mode     -       set host controller for PIO mode
  *      @drive: drive
  *      @pio: PIO mode number
  *
- *      Handles setting of PIO mode for both the chipset and drive.
+ *      Handles setting of PIO mode for the chipset.
  *
  *      The init_hwif_cs5530() routine guarantees that all drives
  *      will have valid default PIO timings set up before we get here.
@@ -83,8 +59,10 @@ static void cs5530_tunepio(ide_drive_t *drive, u8 pio)
 
 static void cs5530_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        if (cs5530_set_xfer_mode(drive, XFER_PIO_0 + pio) == 0)
-                cs5530_tunepio(drive, pio);
+        unsigned long basereg = CS5530_BASEREG(drive->hwif);
+        unsigned int format = (inl(basereg + 4) >> 31) & 1;
+
+        outl(cs5530_pio_timings[format][pio], basereg + ((drive->dn & 1)<<3));
 }
 
 /**
@@ -142,20 +120,11 @@ static int cs5530_config_dma(ide_drive_t *drive)
         return 1;
 }
 
-static int cs5530_tune_chipset(ide_drive_t *drive, const u8 mode)
+static void cs5530_set_dma_mode(ide_drive_t *drive, const u8 mode)
 {
         unsigned long basereg;
         unsigned int reg, timings = 0;
 
-        /*
-         * Tell the drive to switch to the new mode; abort on failure.
-         */
-        if (cs5530_set_xfer_mode(drive, mode))
-                return 1;       /* failure */
-
-        /*
-         * Now tune the chipset to match the drive:
-         */
         switch (mode) {
                 case XFER_UDMA_0:       timings = 0x00921250; break;
                 case XFER_UDMA_1:       timings = 0x00911140; break;
@@ -180,8 +149,6 @@ static int cs5530_tune_chipset(ide_drive_t *drive, const u8 mode)
                 outl(reg, basereg + 4);         /* write drive0 config register */
                 outl(timings, basereg + 12);    /* write drive1 config register */
         }
-
-        return 0;       /* success */
 }
 
 /**
@@ -299,7 +266,7 @@ static void __devinit init_hwif_cs5530 (ide_hwif_t *hwif)
                 hwif->serialized = hwif->mate->serialized = 1;
 
         hwif->set_pio_mode = &cs5530_set_pio_mode;
-        hwif->speedproc = &cs5530_tune_chipset;
+        hwif->set_dma_mode = &cs5530_set_dma_mode;
 
         basereg = CS5530_BASEREG(hwif);
         d0_timings = inl(basereg + 0);
@@ -340,6 +307,7 @@ static ide_pci_device_t cs5530_chipset __devinitdata = {
         .autodma        = AUTODMA,
         .bootable       = ON_BOARD,
         .pio_mask       = ATA_PIO4,
+        .host_flags     = IDE_HFLAG_POST_SET_MODE,
 };
 
 static int __devinit cs5530_init_one(struct pci_dev *dev, const struct pci_device_id *id)
diff --git a/drivers/ide/pci/cs5535.c b/drivers/ide/pci/cs5535.c
index 383b7eccbcbb..257865778f92 100644
--- a/drivers/ide/pci/cs5535.c
+++ b/drivers/ide/pci/cs5535.c
@@ -131,24 +131,21 @@ static void cs5535_set_speed(ide_drive_t *drive, const u8 speed)
         }
 }
 
-/****
- *      cs5535_set_drive         -     Configure the drive to the new speed
- *      @drive: Drive to set up
- *      @speed: desired speed
+/**
+ *      cs5535_set_dma_mode     -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
- *      cs5535_set_drive() configures the drive and the chipset to a
- *      new speed. It also can be called by upper layers.
+ *      Programs the chipset for DMA mode.
  */
-static int cs5535_set_drive(ide_drive_t *drive, u8 speed)
+
+static void cs5535_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
-        ide_config_drive_speed(drive, speed);
         cs5535_set_speed(drive, speed);
-
-        return 0;
 }
 
 /**
- *      cs5535_set_pio_mode     -       PIO setup
+ *      cs5535_set_pio_mode     -       set host controller for PIO mode
  *      @drive: drive
  *      @pio: PIO mode number
  *
@@ -157,7 +154,6 @@ static int cs5535_set_drive(ide_drive_t *drive, u8 speed)
 
 static void cs5535_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        ide_config_drive_speed(drive, XFER_PIO_0 + pio);
         cs5535_set_speed(drive, XFER_PIO_0 + pio);
 }
 
@@ -194,12 +190,16 @@ static u8 __devinit cs5535_cable_detect(struct pci_dev *dev)
  */
 static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
 {
-        int i;
-
         hwif->autodma = 0;
 
         hwif->set_pio_mode = &cs5535_set_pio_mode;
-        hwif->speedproc = &cs5535_set_drive;
+        hwif->set_dma_mode = &cs5535_set_dma_mode;
+
+        hwif->drives[1].autotune = hwif->drives[0].autotune = 1;
+
+        if (hwif->dma_base == 0)
+                return;
+
         hwif->ide_dma_check = &cs5535_dma_check;
 
         hwif->atapi_dma = 1;
@@ -211,11 +211,7 @@ static void __devinit init_hwif_cs5535(ide_hwif_t *hwif)
         if (!noautodma)
                 hwif->autodma = 1;
 
-        /* just setting autotune and not worrying about bios timings */
-        for (i = 0; i < 2; i++) {
-                hwif->drives[i].autotune = 1;
-                hwif->drives[i].autodma = hwif->autodma;
-        }
+        hwif->drives[1].autodma = hwif->drives[0].autodma = hwif->autodma;
 }
 
 static ide_pci_device_t cs5535_chipset __devinitdata = {
@@ -223,7 +219,7 @@ static ide_pci_device_t cs5535_chipset __devinitdata = {
         .init_hwif      = init_hwif_cs5535,
         .autodma        = AUTODMA,
         .bootable       = ON_BOARD,
-        .host_flags     = IDE_HFLAG_SINGLE,
+        .host_flags     = IDE_HFLAG_SINGLE | IDE_HFLAG_POST_SET_MODE,
         .pio_mask       = ATA_PIO4,
 };
 
diff --git a/drivers/ide/pci/hpt34x.c b/drivers/ide/pci/hpt34x.c
index a1bb10188fe5..218852aaf22a 100644
--- a/drivers/ide/pci/hpt34x.c
+++ b/drivers/ide/pci/hpt34x.c
@@ -43,7 +43,7 @@
 
 #define HPT343_DEBUG_DRIVE_INFO         0
 
-static int hpt34x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void hpt34x_set_mode(ide_drive_t *drive, const u8 speed)
 {
         struct pci_dev *dev     = HWIF(drive)->pci_dev;
         u32 reg1= 0, tmp1 = 0, reg2 = 0, tmp2 = 0;
@@ -73,13 +73,11 @@ static int hpt34x_tune_chipset(ide_drive_t *drive, const u8 speed)
                 drive->dn, reg1, tmp1, reg2, tmp2,
                 hi_speed, lo_speed);
 #endif /* HPT343_DEBUG_DRIVE_INFO */
-
-        return(ide_config_drive_speed(drive, speed));
 }
 
 static void hpt34x_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        (void) hpt34x_tune_chipset(drive, (XFER_PIO_0 + pio));
+        hpt34x_set_mode(drive, XFER_PIO_0 + pio);
 }
 
 static int hpt34x_config_drive_xfer_rate (ide_drive_t *drive)
@@ -145,7 +143,8 @@ static void __devinit init_hwif_hpt34x(ide_hwif_t *hwif)
         hwif->autodma = 0;
 
         hwif->set_pio_mode = &hpt34x_set_pio_mode;
-        hwif->speedproc = &hpt34x_tune_chipset;
+        hwif->set_dma_mode = &hpt34x_set_mode;
+
         hwif->drives[0].autotune = 1;
         hwif->drives[1].autotune = 1;
 
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c
index 0e7d3b60d43c..8812a9bb032f 100644
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -600,7 +600,7 @@ static u32 get_speed_setting(u8 speed, struct hpt_info *info)
         return (*info->settings)[i];
 }
 
-static int hpt36x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void hpt36x_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev  *dev    = hwif->pci_dev;
@@ -623,11 +623,9 @@ static int hpt36x_tune_chipset(ide_drive_t *drive, const u8 speed)
         new_itr &= ~0xc0000000;
 
         pci_write_config_dword(dev, itr_addr, new_itr);
-
-        return ide_config_drive_speed(drive, speed);
 }
 
-static int hpt37x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void hpt37x_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev  *dev    = hwif->pci_dev;
@@ -647,24 +645,22 @@ static int hpt37x_tune_chipset(ide_drive_t *drive, const u8 speed)
         if (speed < XFER_MW_DMA_0)
                 new_itr &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
         pci_write_config_dword(dev, itr_addr, new_itr);
-
-        return ide_config_drive_speed(drive, speed);
 }
 
-static int hpt3xx_tune_chipset(ide_drive_t *drive, u8 speed)
+static void hpt3xx_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct hpt_info *info   = pci_get_drvdata(hwif->pci_dev);
 
         if (info->chip_type >= HPT370)
-                return hpt37x_tune_chipset(drive, speed);
+                hpt37x_set_mode(drive, speed);
         else    /* hpt368: hpt_minimum_revision(dev, 2) */
-                return hpt36x_tune_chipset(drive, speed);
+                hpt36x_set_mode(drive, speed);
 }
 
 static void hpt3xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        (void) hpt3xx_tune_chipset (drive, XFER_PIO_0 + pio);
+        hpt3xx_set_mode(drive, XFER_PIO_0 + pio);
 }
 
 static int hpt3xx_quirkproc(ide_drive_t *drive)
@@ -1257,7 +1253,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
         hwif->select_data       = hwif->channel ? 0x54 : 0x50;
 
         hwif->set_pio_mode      = &hpt3xx_set_pio_mode;
-        hwif->speedproc         = &hpt3xx_tune_chipset;
+        hwif->set_dma_mode      = &hpt3xx_set_mode;
         hwif->quirkproc         = &hpt3xx_quirkproc;
         hwif->intrproc          = &hpt3xx_intrproc;
         hwif->maskproc          = &hpt3xx_maskproc;
diff --git a/drivers/ide/pci/it8213.c b/drivers/ide/pci/it8213.c
index 76e91ff9420b..ecf4ce078dce 100644
--- a/drivers/ide/pci/it8213.c
+++ b/drivers/ide/pci/it8213.c
@@ -48,15 +48,15 @@ static u8 it8213_dma_2_pio (u8 xfer_rate) {
         }
 }
 
-/*
- *      it8213_tune_pio -       tune a drive
- *      @drive: drive to tune
- *      @pio: desired PIO mode
+/**
+ *      it8213_set_pio_mode     -       set host controller for PIO mode
+ *      @drive: drive
+ *      @pio: PIO mode number
  *
  *      Set the interface PIO mode.
  */
 
-static void it8213_tune_pio(ide_drive_t *drive, const u8 pio)
+static void it8213_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -105,21 +105,15 @@ static void it8213_tune_pio(ide_drive_t *drive, const u8 pio)
         spin_unlock_irqrestore(&tune_lock, flags);
 }
 
-static void it8213_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        it8213_tune_pio(drive, pio);
-        ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
 /**
- *      it8213_tune_chipset     -       set controller timings
- *      @drive: Drive to set up
- *      @speed: speed we want to achieve
+ *      it8213_set_dma_mode     -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
- *      Tune the ITE chipset for the desired mode.
+ *      Tune the ITE chipset for the DMA mode.
  */
 
-static int it8213_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void it8213_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -152,7 +146,7 @@ static int it8213_tune_chipset(ide_drive_t *drive, const u8 speed)
                 case XFER_SW_DMA_2:
                         break;
                 default:
-                        return -1;
+                        return;
         }
 
         if (speed >= XFER_UDMA_0) {
@@ -182,9 +176,7 @@ static int it8213_tune_chipset(ide_drive_t *drive, const u8 speed)
                         pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
         }
 
-        it8213_tune_pio(drive, it8213_dma_2_pio(speed));
-
-        return ide_config_drive_speed(drive, speed);
+        it8213_set_pio_mode(drive, it8213_dma_2_pio(speed));
 }
 
 /**
@@ -220,7 +212,7 @@ static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
 {
         u8 reg42h = 0;
 
-        hwif->speedproc = &it8213_tune_chipset;
+        hwif->set_dma_mode = &it8213_set_dma_mode;
         hwif->set_pio_mode = &it8213_set_pio_mode;
 
         hwif->autodma = 0;
diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c
index 758a98230cc5..1b69d82478c6 100644
--- a/drivers/ide/pci/it821x.c
+++ b/drivers/ide/pci/it821x.c
@@ -229,24 +229,24 @@ static void it821x_clock_strategy(ide_drive_t *drive)
 }
 
 /**
- *      it821x_tunepio  -       tune a drive
- *      @drive: drive to tune
- *      @pio: the desired PIO mode
+ *      it821x_set_pio_mode     -       set host controller for PIO mode
+ *      @drive: drive
+ *      @pio: PIO mode number
  *
- *      Try to tune the drive/host to the desired PIO mode taking into
- *      the consideration the maximum PIO mode supported by the other
- *      device on the cable.
+ *      Tune the host to the desired PIO mode taking into the consideration
+ *      the maximum PIO mode supported by the other device on the cable.
  */
 
-static int it821x_tunepio(ide_drive_t *drive, u8 set_pio)
+static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         ide_hwif_t *hwif        = drive->hwif;
         struct it821x_dev *itdev = ide_get_hwifdata(hwif);
         int unit = drive->select.b.unit;
         ide_drive_t *pair = &hwif->drives[1 - unit];
+        u8 set_pio = pio;
 
         /* Spec says 89 ref driver uses 88 */
-        static u16 pio[]        = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
+        static u16 pio_timings[]= { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
         static u8 pio_want[]    = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
 
         /*
@@ -261,22 +261,12 @@ static int it821x_tunepio(ide_drive_t *drive, u8 set_pio)
                         set_pio = pair_pio;
         }
 
-        if (itdev->smart)
-                return 0;
-
         /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
         itdev->want[unit][1] = pio_want[set_pio];
         itdev->want[unit][0] = 1;       /* PIO is lowest priority */
-        itdev->pio[unit] = pio[set_pio];
+        itdev->pio[unit] = pio_timings[set_pio];
         it821x_clock_strategy(drive);
         it821x_program(drive, itdev->pio[unit]);
-
-        return ide_config_drive_speed(drive, XFER_PIO_0 + set_pio);
-}
-
-static void it821x_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        (void)it821x_tunepio(drive, pio);
 }
 
 /**
@@ -405,47 +395,24 @@ static int it821x_dma_end(ide_drive_t *drive)
 }
 
 /**
- *      it821x_tune_chipset     -       set controller timings
- *      @drive: Drive to set up
- *      @speed: speed we want to achieve
+ *      it821x_set_dma_mode     -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
- *      Tune the ITE chipset for the desired mode.
+ *      Tune the ITE chipset for the desired DMA mode.
  */
 
-static int it821x_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void it821x_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
-
-        ide_hwif_t *hwif        = drive->hwif;
-        struct it821x_dev *itdev = ide_get_hwifdata(hwif);
-
-        if (itdev->smart == 0) {
-                switch (speed) {
-                        /* MWDMA tuning is really hard because our MWDMA and PIO
-                           timings are kept in the same place. We can switch in the
-                           host dma on/off callbacks */
-                        case XFER_MW_DMA_2:
-                        case XFER_MW_DMA_1:
-                        case XFER_MW_DMA_0:
-                                it821x_tune_mwdma(drive, (speed - XFER_MW_DMA_0));
-                                break;
-                        case XFER_UDMA_6:
-                        case XFER_UDMA_5:
-                        case XFER_UDMA_4:
-                        case XFER_UDMA_3:
-                        case XFER_UDMA_2:
-                        case XFER_UDMA_1:
-                        case XFER_UDMA_0:
-                                it821x_tune_udma(drive, (speed - XFER_UDMA_0));
-                                break;
-                        default:
-                                return 1;
-                }
-
-                return ide_config_drive_speed(drive, speed);
-        }
-
-        /* don't touch anything in the smart mode */
-        return 0;
+        /*
+         * MWDMA tuning is really hard because our MWDMA and PIO
+         * timings are kept in the same place.  We can switch in the
+         * host dma on/off callbacks.
+         */
+        if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_6)
+                it821x_tune_udma(drive, speed - XFER_UDMA_0);
+        else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+                it821x_tune_mwdma(drive, speed - XFER_MW_DMA_0);
 }
 
 /**
@@ -629,14 +596,15 @@ static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
                         printk(KERN_WARNING "it821x: Revision 0x10, workarounds activated.\n");
         }
 
-        hwif->speedproc = &it821x_tune_chipset;
-        hwif->set_pio_mode = &it821x_set_pio_mode;
+        if (idev->smart == 0) {
+                hwif->set_pio_mode = &it821x_set_pio_mode;
+                hwif->set_dma_mode = &it821x_set_dma_mode;
 
-        /* MWDMA/PIO clock switching for pass through mode */
-        if(!idev->smart) {
+                /* MWDMA/PIO clock switching for pass through mode */
                 hwif->dma_start = &it821x_dma_start;
                 hwif->ide_dma_end = &it821x_dma_end;
-        }
+        } else
+                hwif->host_flags |= IDE_HFLAG_NO_SET_MODE;
 
         hwif->drives[0].autotune = 1;
         hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/jmicron.c b/drivers/ide/pci/jmicron.c
index d379fbaf6743..582b4cae2b53 100644
--- a/drivers/ide/pci/jmicron.c
+++ b/drivers/ide/pci/jmicron.c
@@ -85,21 +85,18 @@ static u8 __devinit ata66_jmicron(ide_hwif_t *hwif)
 
 static void jmicron_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }
 
 /**
- *      jmicron_tune_chipset    -       set controller timings
- *      @drive: Drive to set up
- *      @speed: speed we want to achieve
+ *      jmicron_set_dma_mode    -       set host controller for DMA mode
+ *      @drive: drive
+ *      @mode: DMA mode
  *
- *      As the JMicron snoops for timings all we actually need to do is
- *      set the transfer mode on the device.
+ *      As the JMicron snoops for timings we don't need to do anything here.
  */
 
-static int jmicron_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void jmicron_set_dma_mode(ide_drive_t *drive, const u8 mode)
 {
-        return ide_config_drive_speed(drive, speed);
 }
 
 /**
@@ -129,8 +126,8 @@ static int jmicron_config_drive_for_dma (ide_drive_t *drive)
 
 static void __devinit init_hwif_jmicron(ide_hwif_t *hwif)
 {
-        hwif->speedproc = &jmicron_tune_chipset;
         hwif->set_pio_mode = &jmicron_set_pio_mode;
+        hwif->set_dma_mode = &jmicron_set_dma_mode;
 
         hwif->drives[0].autotune = 1;
         hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/pdc202xx_new.c b/drivers/ide/pci/pdc202xx_new.c
index 5fb1eedc8194..ad0bdcb0c02b 100644
--- a/drivers/ide/pci/pdc202xx_new.c
+++ b/drivers/ide/pci/pdc202xx_new.c
@@ -146,19 +146,16 @@ static struct udma_timing {
         { 0x1a, 0x01, 0xcb },   /* UDMA mode 6 */
 };
 
-static int pdcnew_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void pdcnew_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         u8 adj                  = (drive->dn & 1) ? 0x08 : 0x00;
-        int                     err;
 
         /*
-         * Issue SETFEATURES_XFER to the drive first. PDC202xx hardware will
+         * IDE core issues SETFEATURES_XFER to the drive first (thanks to
+         * IDE_HFLAG_POST_SET_MODE in ->host_flags).  PDC202xx hardware will
          * automatically set the timing registers based on 100 MHz PLL output.
-         */
-        err = ide_config_drive_speed(drive, speed);
-
-        /*
+         *
          * As we set up the PLL to output 133 MHz for UltraDMA/133 capable
          * chips, we must override the default register settings...
          */
@@ -211,13 +208,11 @@ static int pdcnew_tune_chipset(ide_drive_t *drive, const u8 speed)
 
                 set_indexed_reg(hwif, 0x10 + adj, tmp & 0x7f);
         }
-
-        return err;
 }
 
 static void pdcnew_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        (void)pdcnew_tune_chipset(drive, XFER_PIO_0 + pio);
+        pdcnew_set_mode(drive, XFER_PIO_0 + pio);
 }
 
 static u8 pdcnew_cable_detect(ide_hwif_t *hwif)
@@ -490,9 +485,9 @@ static void __devinit init_hwif_pdc202new(ide_hwif_t *hwif)
         hwif->autodma = 0;
 
         hwif->set_pio_mode = &pdcnew_set_pio_mode;
+        hwif->set_dma_mode = &pdcnew_set_mode;
 
         hwif->quirkproc = &pdcnew_quirkproc;
-        hwif->speedproc = &pdcnew_tune_chipset;
         hwif->resetproc = &pdcnew_reset;
 
         hwif->err_stops_fifo = 1;
@@ -583,6 +578,7 @@ static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
                 .bootable       = OFF_BOARD,
                 .pio_mask       = ATA_PIO4,
                 .udma_mask      = 0x3f, /* udma0-5 */
+                .host_flags     = IDE_HFLAG_POST_SET_MODE,
         },{     /* 1 */
                 .name           = "PDC20269",
                 .init_setup     = init_setup_pdcnew,
@@ -592,6 +588,7 @@ static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
                 .bootable       = OFF_BOARD,
                 .pio_mask       = ATA_PIO4,
                 .udma_mask      = 0x7f, /* udma0-6*/
+                .host_flags     = IDE_HFLAG_POST_SET_MODE,
         },{     /* 2 */
                 .name           = "PDC20270",
                 .init_setup     = init_setup_pdc20270,
@@ -601,6 +598,7 @@ static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
                 .bootable       = OFF_BOARD,
                 .pio_mask       = ATA_PIO4,
                 .udma_mask      = 0x3f, /* udma0-5 */
+                .host_flags     = IDE_HFLAG_POST_SET_MODE,
         },{     /* 3 */
                 .name           = "PDC20271",
                 .init_setup     = init_setup_pdcnew,
@@ -610,6 +608,7 @@ static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
                 .bootable       = OFF_BOARD,
                 .pio_mask       = ATA_PIO4,
                 .udma_mask      = 0x7f, /* udma0-6*/
+                .host_flags     = IDE_HFLAG_POST_SET_MODE,
         },{     /* 4 */
                 .name           = "PDC20275",
                 .init_setup     = init_setup_pdcnew,
@@ -619,6 +618,7 @@ static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
                 .bootable       = OFF_BOARD,
                 .pio_mask       = ATA_PIO4,
                 .udma_mask      = 0x7f, /* udma0-6*/
+                .host_flags     = IDE_HFLAG_POST_SET_MODE,
         },{     /* 5 */
                 .name           = "PDC20276",
                 .init_setup     = init_setup_pdc20276,
@@ -628,6 +628,7 @@ static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
                 .bootable       = OFF_BOARD,
                 .pio_mask       = ATA_PIO4,
                 .udma_mask      = 0x7f, /* udma0-6*/
+                .host_flags     = IDE_HFLAG_POST_SET_MODE,
         },{     /* 6 */
                 .name           = "PDC20277",
                 .init_setup     = init_setup_pdcnew,
@@ -637,6 +638,7 @@ static ide_pci_device_t pdcnew_chipsets[] __devinitdata = {
                 .bootable       = OFF_BOARD,
                 .pio_mask       = ATA_PIO4,
                 .udma_mask      = 0x7f, /* udma0-6*/
+                .host_flags     = IDE_HFLAG_POST_SET_MODE,
         }
 };
 
diff --git a/drivers/ide/pci/pdc202xx_old.c b/drivers/ide/pci/pdc202xx_old.c
index b578307fad51..8c3e8cf36ec9 100644
--- a/drivers/ide/pci/pdc202xx_old.c
+++ b/drivers/ide/pci/pdc202xx_old.c
@@ -63,7 +63,7 @@ static const char *pdc_quirk_drives[] = {
 
 static void pdc_old_disable_66MHz_clock(ide_hwif_t *);
 
-static int pdc202xx_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void pdc202xx_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -138,13 +138,11 @@ static int pdc202xx_tune_chipset(ide_drive_t *drive, const u8 speed)
         pci_read_config_dword(dev, drive_pci, &drive_conf);
         printk("0x%08x\n", drive_conf);
 #endif
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 static void pdc202xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        pdc202xx_tune_chipset(drive, XFER_PIO_0 + pio);
+        pdc202xx_set_mode(drive, XFER_PIO_0 + pio);
 }
 
 static u8 pdc202xx_old_cable_detect (ide_hwif_t *hwif)
@@ -330,14 +328,13 @@ static void __devinit init_hwif_pdc202xx(ide_hwif_t *hwif)
         hwif->autodma = 0;
 
         hwif->set_pio_mode = &pdc202xx_set_pio_mode;
+        hwif->set_dma_mode = &pdc202xx_set_mode;
 
         hwif->quirkproc = &pdc202xx_quirkproc;
 
         if (hwif->pci_dev->device != PCI_DEVICE_ID_PROMISE_20246)
                 hwif->resetproc = &pdc202xx_reset;
 
-        hwif->speedproc = &pdc202xx_tune_chipset;
-
         hwif->err_stops_fifo = 1;
 
         hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/piix.c b/drivers/ide/pci/piix.c
index fd8214a7ab98..38c91ba6497b 100644
--- a/drivers/ide/pci/piix.c
+++ b/drivers/ide/pci/piix.c
@@ -137,13 +137,14 @@ static u8 piix_dma_2_pio (u8 xfer_rate) {
 }
 
 /**
- *      piix_tune_pio           -       tune PIIX for PIO mode
- *      @drive: drive to tune
- *      @pio: desired PIO mode
+ *      piix_set_pio_mode       -       set host controller for PIO mode
+ *      @drive: drive
+ *      @pio: PIO mode number
  *
  *      Set the interface PIO mode based upon the settings done by AMI BIOS.
  */
-static void piix_tune_pio (ide_drive_t *drive, u8 pio)
+
+static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -204,31 +205,15 @@ static void piix_tune_pio (ide_drive_t *drive, u8 pio)
 }
 
 /**
- *      piix_set_pio_mode       -       set PIO mode
- *      @drive: drive to tune
- *      @pio: desired PIO mode
- *
- *      Set the drive's PIO mode (might be useful if drive is not registered
- *      in CMOS for any reason).
- */
-
-static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        piix_tune_pio(drive, pio);
-        (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-/**
- *      piix_tune_chipset       -       tune a PIIX interface
- *      @drive: IDE drive to tune
- *      @speed: speed to configure
+ *      piix_set_dma_mode       -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
- *      Set a PIIX interface channel to the desired speeds. This involves
- *      requires the right timing data into the PIIX configuration space
- *      then setting the drive parameters appropriately
+ *      Set a PIIX host controller to the desired DMA mode.  This involves
+ *      programming the right timing data into the PCI configuration space.
  */
 
-static int piix_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -259,7 +244,7 @@ static int piix_tune_chipset(ide_drive_t *drive, const u8 speed)
                 case XFER_MW_DMA_2:
                 case XFER_MW_DMA_1:
                 case XFER_SW_DMA_2:     break;
-                default:                return -1;
+                default:                return;
         }
 
         if (speed >= XFER_UDMA_0) {
@@ -288,9 +273,7 @@ static int piix_tune_chipset(ide_drive_t *drive, const u8 speed)
                         pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
         }
 
-        piix_tune_pio(drive, piix_dma_2_pio(speed));
-
-        return ide_config_drive_speed(drive, speed);
+        piix_set_pio_mode(drive, piix_dma_2_pio(speed));
 }
 
 /**
@@ -448,7 +431,8 @@ static void __devinit init_hwif_piix(ide_hwif_t *hwif)
         hwif->autodma = 0;
 
         hwif->set_pio_mode = &piix_set_pio_mode;
-        hwif->speedproc = &piix_tune_chipset;
+        hwif->set_dma_mode = &piix_set_dma_mode;
+
         hwif->drives[0].autotune = 1;
         hwif->drives[1].autotune = 1;
 
diff --git a/drivers/ide/pci/sc1200.c b/drivers/ide/pci/sc1200.c
index 79ecab689489..ee0e3f554d9a 100644
--- a/drivers/ide/pci/sc1200.c
+++ b/drivers/ide/pci/sc1200.c
@@ -68,17 +68,6 @@ static unsigned short sc1200_get_pci_clock (void)
         return pci_clock;
 }
 
-extern char *ide_xfer_verbose (byte xfer_rate);
-
-/*
- * Set a new transfer mode at the drive
- */
-static int sc1200_set_xfer_mode (ide_drive_t *drive, byte mode)
-{
-        printk("%s: sc1200_set_xfer_mode(%s)\n", drive->name, ide_xfer_verbose(mode));
-        return ide_config_drive_speed(drive, mode);
-}
-
 /*
  * Here are the standard PIO mode 0-4 timings for each "format".
  * Format-0 uses fast data reg timings, with slower command reg timings.
@@ -138,7 +127,7 @@ out:
         return mask;
 }
 
-static int sc1200_tune_chipset(ide_drive_t *drive, const u8 mode)
+static void sc1200_set_dma_mode(ide_drive_t *drive, const u8 mode)
 {
         ide_hwif_t              *hwif = HWIF(drive);
         int                     unit = drive->select.b.unit;
@@ -146,17 +135,9 @@ static int sc1200_tune_chipset(ide_drive_t *drive, const u8 mode)
         unsigned short          pci_clock;
         unsigned int            basereg = hwif->channel ? 0x50 : 0x40;
 
-        /*
-         * Tell the drive to switch to the new mode; abort on failure.
-         */
-        if (sc1200_set_xfer_mode(drive, mode))
-                return 1;       /* failure */
-
         pci_clock = sc1200_get_pci_clock();
 
         /*
-         * Now tune the chipset to match the drive:
-         *
          * Note that each DMA mode has several timings associated with it.
          * The correct timing depends on the fast PCI clock freq.
          */
@@ -216,8 +197,6 @@ static int sc1200_tune_chipset(ide_drive_t *drive, const u8 mode)
         } else {
                 pci_write_config_dword(hwif->pci_dev, basereg+12, timings);
         }
-
-        return 0;       /* success */
 }
 
 /*
@@ -286,13 +265,12 @@ static void sc1200_set_pio_mode(ide_drive_t *drive, const u8 pio)
         if (mode != -1) {
                 printk("SC1200: %s: changing (U)DMA mode\n", drive->name);
                 hwif->dma_off_quietly(drive);
-                if (sc1200_tune_chipset(drive, mode) == 0)
+                if (ide_set_dma_mode(drive, mode) == 0)
                         hwif->dma_host_on(drive);
                 return;
         }
 
-        if (sc1200_set_xfer_mode(drive, XFER_PIO_0 + pio) == 0)
-                sc1200_tunepio(drive, pio);
+        sc1200_tunepio(drive, pio);
 }
 
 #ifdef CONFIG_PM
@@ -400,16 +378,20 @@ static void __devinit init_hwif_sc1200 (ide_hwif_t *hwif)
         if (hwif->mate)
                 hwif->serialized = hwif->mate->serialized = 1;
         hwif->autodma = 0;
-        if (hwif->dma_base) {
-                hwif->udma_filter = sc1200_udma_filter;
-                hwif->ide_dma_check = &sc1200_config_dma;
-                hwif->ide_dma_end   = &sc1200_ide_dma_end;
-                if (!noautodma)
-                        hwif->autodma = 1;
-
-                hwif->set_pio_mode = &sc1200_set_pio_mode;
-                hwif->speedproc = &sc1200_tune_chipset;
-        }
+
+        hwif->set_pio_mode = &sc1200_set_pio_mode;
+        hwif->set_dma_mode = &sc1200_set_dma_mode;
+
+        if (hwif->dma_base == 0)
+                return;
+
+        hwif->udma_filter = sc1200_udma_filter;
+        hwif->ide_dma_check = &sc1200_config_dma;
+        hwif->ide_dma_end   = &sc1200_ide_dma_end;
+
+        if (!noautodma)
+                hwif->autodma = 1;
+
         hwif->atapi_dma = 1;
         hwif->ultra_mask = 0x07;
         hwif->mwdma_mask = 0x07;
@@ -423,7 +405,7 @@ static ide_pci_device_t sc1200_chipset __devinitdata = {
         .init_hwif      = init_hwif_sc1200,
         .autodma        = AUTODMA,
         .bootable       = ON_BOARD,
-        .host_flags     = IDE_HFLAG_ABUSE_DMA_MODES,
+        .host_flags     = IDE_HFLAG_ABUSE_DMA_MODES | IDE_HFLAG_POST_SET_MODE,
         .pio_mask       = ATA_PIO4,
 };
 
diff --git a/drivers/ide/pci/scc_pata.c b/drivers/ide/pci/scc_pata.c
index 66a526e0ece4..67f06dd11b34 100644
--- a/drivers/ide/pci/scc_pata.c
+++ b/drivers/ide/pci/scc_pata.c
@@ -190,15 +190,15 @@ scc_ide_outsl(unsigned long port, void *addr, u32 count)
 }
 
 /**
- *      scc_tune_pio    -       tune a drive PIO mode
- *      @drive: drive to tune
- *      @mode_wanted: the target operating mode
+ *      scc_set_pio_mode        -       set host controller for PIO mode
+ *      @drive: drive
+ *      @pio: PIO mode number
  *
  *      Load the timing settings for this device mode into the
  *      controller.
  */
 
-static void scc_tune_pio(ide_drive_t *drive, const u8 pio)
+static void scc_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         ide_hwif_t *hwif = HWIF(drive);
         struct scc_ports *ports = ide_get_hwifdata(hwif);
@@ -221,22 +221,16 @@ static void scc_tune_pio(ide_drive_t *drive, const u8 pio)
         out_be32((void __iomem *)pioct_port, reg);
 }
 
-static void scc_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        scc_tune_pio(drive, pio);
-        ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
 /**
- *      scc_tune_chipset        -       tune a drive DMA mode
- *      @drive: Drive to set up
- *      @speed: speed we want to achieve
+ *      scc_set_dma_mode        -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
  *      Load the timing settings for this device mode into the
  *      controller.
  */
 
-static int scc_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void scc_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif = HWIF(drive);
         struct scc_ports *ports = ide_get_hwifdata(hwif);
@@ -271,7 +265,7 @@ static int scc_tune_chipset(ide_drive_t *drive, const u8 speed)
                 idx = speed - XFER_UDMA_0;
                 break;
         default:
-                return 1;
+                return;
         }
 
         jcactsel = JCACTSELtbl[offset][idx];
@@ -287,8 +281,6 @@ static int scc_tune_chipset(ide_drive_t *drive, const u8 speed)
         }
         reg = JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx];
         out_be32((void __iomem *)udenvt_port, reg);
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 /**
@@ -708,8 +700,8 @@ static void __devinit init_hwif_scc(ide_hwif_t *hwif)
 
         hwif->dma_setup = scc_dma_setup;
         hwif->ide_dma_end = scc_ide_dma_end;
-        hwif->speedproc = scc_tune_chipset;
         hwif->set_pio_mode = scc_set_pio_mode;
+        hwif->set_dma_mode = scc_set_dma_mode;
         hwif->ide_dma_check = scc_config_drive_for_dma;
         hwif->ide_dma_test_irq = scc_dma_test_irq;
         hwif->udma_filter = scc_udma_filter;
diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
index 0351cf210427..49ec0ac64a4b 100644
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -124,7 +124,7 @@ static u8 svwks_csb_check (struct pci_dev *dev)
         return 0;
 }
 
-static void svwks_tune_pio(ide_drive_t *drive, const u8 pio)
+static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
         static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
@@ -145,7 +145,7 @@ static void svwks_tune_pio(ide_drive_t *drive, const u8 pio)
         }
 }
 
-static int svwks_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         static const u8 udma_modes[]            = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
         static const u8 dma_modes[]             = { 0x77, 0x21, 0x20 };
@@ -193,14 +193,6 @@ static int svwks_tune_chipset(ide_drive_t *drive, const u8 speed)
         pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
         pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
         pci_write_config_byte(dev, 0x54, ultra_enable);
-
-        return (ide_config_drive_speed(drive, speed));
-}
-
-static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        svwks_tune_pio(drive, pio);
-        (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }
 
 static int svwks_config_drive_xfer_rate (ide_drive_t *drive)
@@ -384,7 +376,7 @@ static void __devinit init_hwif_svwks (ide_hwif_t *hwif)
                 hwif->irq = hwif->channel ? 15 : 14;
 
         hwif->set_pio_mode = &svwks_set_pio_mode;
-        hwif->speedproc = &svwks_tune_chipset;
+        hwif->set_dma_mode = &svwks_set_dma_mode;
         hwif->udma_filter = &svwks_udma_filter;
 
         hwif->atapi_dma = 1;
diff --git a/drivers/ide/pci/sgiioc4.c b/drivers/ide/pci/sgiioc4.c
index c292e1de1d56..85ffaaa39b1b 100644
--- a/drivers/ide/pci/sgiioc4.c
+++ b/drivers/ide/pci/sgiioc4.c
@@ -291,12 +291,8 @@ static void sgiioc4_dma_off_quietly(ide_drive_t *drive)
         drive->hwif->dma_host_off(drive);
 }
 
-static int sgiioc4_speedproc(ide_drive_t *drive, const u8 speed)
+static void sgiioc4_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
-        if (speed != XFER_MW_DMA_2)
-                return 1;
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 static int sgiioc4_ide_dma_check(ide_drive_t *drive)
@@ -591,11 +587,9 @@ static void __devinit
 ide_init_sgiioc4(ide_hwif_t * hwif)
 {
         hwif->mmio = 1;
-        hwif->atapi_dma = 1;
-        hwif->mwdma_mask = 0x04;
         hwif->pio_mask = 0x00;
         hwif->set_pio_mode = NULL; /* Sets timing for PIO mode */
-        hwif->speedproc = &sgiioc4_speedproc;
+        hwif->set_dma_mode = &sgiioc4_set_dma_mode;
         hwif->selectproc = NULL;/* Use the default routine to select drive */
         hwif->reset_poll = NULL;/* No HBA specific reset_poll needed */
         hwif->pre_reset = NULL; /* No HBA specific pre_set needed */
@@ -606,6 +600,14 @@ ide_init_sgiioc4(ide_hwif_t * hwif)
         hwif->quirkproc = NULL;
         hwif->busproc = NULL;
 
+        hwif->INB = &sgiioc4_INB;
+
+        if (hwif->dma_base == 0)
+                return;
+
+        hwif->atapi_dma = 1;
+        hwif->mwdma_mask = 0x04;
+
         hwif->dma_setup = &sgiioc4_ide_dma_setup;
         hwif->dma_start = &sgiioc4_ide_dma_start;
         hwif->ide_dma_end = &sgiioc4_ide_dma_end;
@@ -617,8 +619,6 @@ ide_init_sgiioc4(ide_hwif_t * hwif)
         hwif->dma_host_off = &sgiioc4_dma_host_off;
         hwif->dma_lost_irq = &sgiioc4_dma_lost_irq;
         hwif->dma_timeout = &ide_dma_timeout;
-
-        hwif->INB = &sgiioc4_INB;
 }
 
 static int __devinit
@@ -688,8 +688,6 @@ sgiioc4_ide_setup_pci_device(struct pci_dev *dev)
         /* Initializing chipset IRQ Registers */
         writel(0x03, (void __iomem *)(irqport + IOC4_INTR_SET * 4));
 
-        ide_init_sgiioc4(hwif);
-
         hwif->autodma = 0;
 
         if (dma_base && ide_dma_sgiioc4(hwif, dma_base) == 0) {
@@ -699,6 +697,8 @@ sgiioc4_ide_setup_pci_device(struct pci_dev *dev)
                 printk(KERN_INFO "%s: %s Bus-Master DMA disabled\n",
                                  hwif->name, DRV_NAME);
 
+        ide_init_sgiioc4(hwif);
+
         if (probe_hwif_init(hwif))
                 return -EIO;
 
diff --git a/drivers/ide/pci/siimage.c b/drivers/ide/pci/siimage.c
index 5d1e5e52a044..ce7784996d12 100644
--- a/drivers/ide/pci/siimage.c
+++ b/drivers/ide/pci/siimage.c
@@ -165,16 +165,16 @@ out:
 }
 
 /**
- *      sil_tune_pio    -       tune a drive
- *      @drive: drive to tune
- *      @pio: the desired PIO mode
+ *      sil_set_pio_mode        -       set host controller for PIO mode
+ *      @drive: drive
+ *      @pio: PIO mode number
  *
  *      Load the timing settings for this device mode into the
  *      controller. If we are in PIO mode 3 or 4 turn on IORDY
  *      monitoring (bit 9). The TF timing is bits 31:16
  */
 
-static void sil_tune_pio(ide_drive_t *drive, u8 pio)
+static void sil_set_pio_mode(ide_drive_t *drive, u8 pio)
 {
         const u16 tf_speed[]    = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 };
         const u16 data_speed[]  = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 };
@@ -234,21 +234,15 @@ static void sil_tune_pio(ide_drive_t *drive, u8 pio)
         }
 }
 
-static void sil_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        sil_tune_pio(drive, pio);
-        (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
 /**
- *      siimage_tune_chipset    -       set controller timings
- *      @drive: Drive to set up
- *      @speed: speed we want to achieve
+ *      sil_set_dma_mode        -       set host controller for DMA mode
+ *      @drive: drive
+ *      @speed: DMA mode
  *
- *      Tune the SII chipset for the desired mode.
+ *      Tune the SiI chipset for the desired DMA mode.
  */
 
-static int siimage_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         u8 ultra6[]             = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
         u8 ultra5[]             = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
@@ -303,7 +297,7 @@ static int siimage_tune_chipset(ide_drive_t *drive, const u8 speed)
                         mode |= ((unit) ? 0x30 : 0x03);
                         break;
                 default:
-                        return 1;
+                        return;
         }
 
         if (hwif->mmio) {
@@ -315,7 +309,6 @@ static int siimage_tune_chipset(ide_drive_t *drive, const u8 speed)
                 pci_write_config_word(hwif->pci_dev, ma, multi);
                 pci_write_config_word(hwif->pci_dev, ua, ultra);
         }
-        return (ide_config_drive_speed(drive, speed));
 }
 
 /**
@@ -904,8 +897,8 @@ static void __devinit init_hwif_siimage(ide_hwif_t *hwif)
         hwif->autodma = 0;
         
         hwif->resetproc = &siimage_reset;
-        hwif->speedproc = &siimage_tune_chipset;
         hwif->set_pio_mode = &sil_set_pio_mode;
+        hwif->set_dma_mode = &sil_set_dma_mode;
         hwif->reset_poll = &siimage_reset_poll;
         hwif->pre_reset = &siimage_pre_reset;
         hwif->udma_filter = &sil_udma_filter;
diff --git a/drivers/ide/pci/sis5513.c b/drivers/ide/pci/sis5513.c
index 3e18899de631..b375ee53d66d 100644
--- a/drivers/ide/pci/sis5513.c
+++ b/drivers/ide/pci/sis5513.c
@@ -451,7 +451,7 @@ static void config_drive_art_rwp (ide_drive_t *drive)
 }
 
 /* Set per-drive active and recovery time */
-static void config_art_rwp_pio (ide_drive_t *drive, u8 pio)
+static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -519,20 +519,14 @@ static void config_art_rwp_pio (ide_drive_t *drive, u8 pio)
         }
 }
 
-static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        config_art_rwp_pio(drive, pio);
-        (void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-static int sis5513_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void sis_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
         u32 regdw;
         u8 drive_pci, reg;
 
-        /* See config_art_rwp_pio for drive pci config registers */
+        /* See sis_set_pio_mode() for drive PCI config registers */
         drive_pci = 0x40;
         if (chipset_family >= ATA_133) {
                 u32 reg54h;
@@ -600,8 +594,6 @@ static int sis5513_tune_chipset(ide_drive_t *drive, const u8 speed)
                         BUG();
                         break;
         }
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 static int sis5513_config_xfer_rate(ide_drive_t *drive)
@@ -841,7 +833,7 @@ static void __devinit init_hwif_sis5513 (ide_hwif_t *hwif)
                 hwif->irq = hwif->channel ? 15 : 14;
 
         hwif->set_pio_mode = &sis_set_pio_mode;
-        hwif->speedproc = &sis5513_tune_chipset;
+        hwif->set_dma_mode = &sis_set_dma_mode;
 
         if (chipset_family >= ATA_133)
                 hwif->udma_filter = sis5513_ata133_udma_filter;
diff --git a/drivers/ide/pci/sl82c105.c b/drivers/ide/pci/sl82c105.c
index f492318ba797..2ef26e3f7be4 100644
--- a/drivers/ide/pci/sl82c105.c
+++ b/drivers/ide/pci/sl82c105.c
@@ -75,7 +75,7 @@ static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio)
 /*
  * Configure the chipset for PIO mode.
  */
-static void sl82c105_tune_pio(ide_drive_t *drive, const u8 pio)
+static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         struct pci_dev *dev     = HWIF(drive)->pci_dev;
         int reg                 = 0x44 + drive->dn * 4;
@@ -105,9 +105,9 @@ static void sl82c105_tune_pio(ide_drive_t *drive, const u8 pio)
 }
 
 /*
- * Configure the drive and chipset for a new transfer speed.
+ * Configure the chipset for DMA mode.
  */
-static int sl82c105_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         static u16 mwdma_timings[] = {0x0707, 0x0201, 0x0200};
         u16 drv_ctrl;
@@ -140,10 +140,8 @@ static int sl82c105_tune_chipset(ide_drive_t *drive, const u8 speed)
                 }
                 break;
         default:
-                return -1;
+                return;
         }
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 /*
@@ -306,17 +304,6 @@ static void sl82c105_resetproc(ide_drive_t *drive)
         pci_read_config_dword(dev, 0x40, &val);
         pci_set_drvdata(dev, (void *)val);
 }
-        
-/*
- * We only deal with PIO mode here - DMA mode 'using_dma' is not
- * initialised at the point that this function is called.
- */
-static void sl82c105_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        sl82c105_tune_pio(drive, pio);
-
-        (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
 
 /*
  * Return the revision of the Winbond bridge
@@ -383,7 +370,7 @@ static void __devinit init_hwif_sl82c105(ide_hwif_t *hwif)
         DBG(("init_hwif_sl82c105(hwif: ide%d)\n", hwif->index));
 
         hwif->set_pio_mode      = &sl82c105_set_pio_mode;
-        hwif->speedproc         = &sl82c105_tune_chipset;
+        hwif->set_dma_mode      = &sl82c105_set_dma_mode;
         hwif->selectproc        = &sl82c105_selectproc;
         hwif->resetproc         = &sl82c105_resetproc;
 
diff --git a/drivers/ide/pci/slc90e66.c b/drivers/ide/pci/slc90e66.c
index ae8e91324577..ebac87f7200a 100644
--- a/drivers/ide/pci/slc90e66.c
+++ b/drivers/ide/pci/slc90e66.c
@@ -42,7 +42,7 @@ static u8 slc90e66_dma_2_pio (u8 xfer_rate) {
         }
 }
 
-static void slc90e66_tune_pio (ide_drive_t *drive, u8 pio)
+static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -95,13 +95,7 @@ static void slc90e66_tune_pio (ide_drive_t *drive, u8 pio)
         spin_unlock_irqrestore(&ide_lock, flags);
 }
 
-static void slc90e66_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-        slc90e66_tune_pio(drive, pio);
-        (void) ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
-static int slc90e66_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void slc90e66_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
@@ -125,7 +119,7 @@ static int slc90e66_tune_chipset(ide_drive_t *drive, const u8 speed)
                 case XFER_MW_DMA_2:
                 case XFER_MW_DMA_1:
                 case XFER_SW_DMA_2:     break;
-                default:                return -1;
+                default:                return;
         }
 
         if (speed >= XFER_UDMA_0) {
@@ -144,9 +138,7 @@ static int slc90e66_tune_chipset(ide_drive_t *drive, const u8 speed)
                         pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
         }
 
-        slc90e66_tune_pio(drive, slc90e66_dma_2_pio(speed));
-
-        return ide_config_drive_speed(drive, speed);
+        slc90e66_set_pio_mode(drive, slc90e66_dma_2_pio(speed));
 }
 
 static int slc90e66_config_drive_xfer_rate (ide_drive_t *drive)
@@ -172,8 +164,8 @@ static void __devinit init_hwif_slc90e66 (ide_hwif_t *hwif)
         if (!hwif->irq)
                 hwif->irq = hwif->channel ? 15 : 14;
 
-        hwif->speedproc = &slc90e66_tune_chipset;
         hwif->set_pio_mode = &slc90e66_set_pio_mode;
+        hwif->set_dma_mode = &slc90e66_set_dma_mode;
 
         pci_read_config_byte(hwif->pci_dev, 0x47, &reg47);
 
diff --git a/drivers/ide/pci/tc86c001.c b/drivers/ide/pci/tc86c001.c
index e23b9cfb6eb4..840415d68d38 100644
--- a/drivers/ide/pci/tc86c001.c
+++ b/drivers/ide/pci/tc86c001.c
@@ -13,7 +13,7 @@
 #include <linux/pci.h>
 #include <linux/ide.h>
 
-static int tc86c001_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void tc86c001_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         unsigned long scr_port  = hwif->config_data + (drive->dn ? 0x02 : 0x00);
@@ -39,13 +39,11 @@ static int tc86c001_tune_chipset(ide_drive_t *drive, const u8 speed)
         scr &= (speed < XFER_MW_DMA_0) ? 0xf8ff : 0xff0f;
         scr |= mode;
         outw(scr, scr_port);
-
-        return ide_config_drive_speed(drive, speed);
 }
 
 static void tc86c001_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        (void) tc86c001_tune_chipset(drive, XFER_PIO_0 + pio);
+        tc86c001_set_mode(drive, XFER_PIO_0 + pio);
 }
 
 /*
@@ -193,7 +191,8 @@ static void __devinit init_hwif_tc86c001(ide_hwif_t *hwif)
         hwif->config_data = sc_base;
 
         hwif->set_pio_mode = &tc86c001_set_pio_mode;
-        hwif->speedproc = &tc86c001_tune_chipset;
+        hwif->set_dma_mode = &tc86c001_set_mode;
+
         hwif->busproc   = &tc86c001_busproc;
 
         hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
diff --git a/drivers/ide/pci/triflex.c b/drivers/ide/pci/triflex.c
index c3ff066eea5a..54e411d4e56c 100644
--- a/drivers/ide/pci/triflex.c
+++ b/drivers/ide/pci/triflex.c
@@ -40,7 +40,7 @@
 #include <linux/ide.h>
 #include <linux/init.h>
 
-static int triflex_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void triflex_set_mode(ide_drive_t *drive, const u8 speed)
 {
         ide_hwif_t *hwif = HWIF(drive);
         struct pci_dev *dev = hwif->pci_dev;
@@ -82,20 +82,18 @@ static int triflex_tune_chipset(ide_drive_t *drive, const u8 speed)
                         timing = 0x0808;
                         break;
                 default:
-                        return -1;
+                        return;
         }
 
         triflex_timings &= ~(0xFFFF << (16 * unit));
         triflex_timings |= (timing << (16 * unit));
         
         pci_write_config_dword(dev, channel_offset, triflex_timings);
-        
-        return (ide_config_drive_speed(drive, speed));
 }
 
 static void triflex_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        (void)triflex_tune_chipset(drive, XFER_PIO_0 + pio);
+        triflex_set_mode(drive, XFER_PIO_0 + pio);
 }
 
 static int triflex_config_drive_xfer_rate(ide_drive_t *drive)
@@ -111,7 +109,7 @@ static int triflex_config_drive_xfer_rate(ide_drive_t *drive)
 static void __devinit init_hwif_triflex(ide_hwif_t *hwif)
 {
         hwif->set_pio_mode = &triflex_set_pio_mode;
-        hwif->speedproc = &triflex_tune_chipset;
+        hwif->set_dma_mode = &triflex_set_mode;
 
         if (hwif->dma_base == 0)
                 return;
diff --git a/drivers/ide/pci/via82cxxx.c b/drivers/ide/pci/via82cxxx.c
index 378feb491ec4..479e49661032 100644
--- a/drivers/ide/pci/via82cxxx.c
+++ b/drivers/ide/pci/via82cxxx.c
@@ -1,6 +1,6 @@
 /*
  *
- * Version 3.48
+ * Version 3.49
  *
  * VIA IDE driver for Linux. Supported southbridges:
  *
@@ -153,21 +153,17 @@ static void via_set_speed(ide_hwif_t *hwif, u8 dn, struct ide_timing *timing)
  *      @drive: Drive to set up
  *      @speed: desired speed
  *
- *      via_set_drive() computes timing values configures the drive and
- *      the chipset to a desired transfer mode. It also can be called
- *      by upper layers.
+ *      via_set_drive() computes timing values configures the chipset to
+ *      a desired transfer mode.  It also can be called by upper layers.
  */
 
-static int via_set_drive(ide_drive_t *drive, const u8 speed)
+static void via_set_drive(ide_drive_t *drive, const u8 speed)
 {
         ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1);
         struct via82cxxx_dev *vdev = pci_get_drvdata(drive->hwif->pci_dev);
         struct ide_timing t, p;
         unsigned int T, UT;
 
-        if (speed != XFER_PIO_SLOW)
-                ide_config_drive_speed(drive, speed);
-
         T = 1000000000 / via_clock;
 
         switch (vdev->via_config->udma_mask) {
@@ -186,16 +182,10 @@ static int via_set_drive(ide_drive_t *drive, const u8 speed)
         }
 
         via_set_speed(HWIF(drive), drive->dn, &t);
-
-        if (!drive->init_speed)
-                drive->init_speed = speed;
-        drive->current_speed = speed;
-
-        return 0;
 }
 
 /**
- *      via_set_pio_mode        -       PIO setup
+ *      via_set_pio_mode        -       set host controller for PIO mode
  *      @drive: drive
  *      @pio: PIO mode number
  *
@@ -456,8 +446,7 @@ static void __devinit init_hwif_via82cxxx(ide_hwif_t *hwif)
         hwif->autodma = 0;
 
         hwif->set_pio_mode = &via_set_pio_mode;
-        hwif->speedproc = &via_set_drive;
-
+        hwif->set_dma_mode = &via_set_drive;
 
 #ifdef CONFIG_PPC_CHRP
         if(machine_is(chrp) && _chrp_type == _CHRP_Pegasos) {
@@ -500,7 +489,8 @@ static ide_pci_device_t via82cxxx_chipsets[] __devinitdata = {
                 .enablebits     = {{0x40,0x02,0x02}, {0x40,0x01,0x01}},
                 .bootable       = ON_BOARD,
                 .host_flags     = IDE_HFLAG_PIO_NO_BLACKLIST
-                                | IDE_HFLAG_PIO_NO_DOWNGRADE,
+                                | IDE_HFLAG_PIO_NO_DOWNGRADE
+                                | IDE_HFLAG_POST_SET_MODE,
                 .pio_mask       = ATA_PIO5,
         },{     /* 1 */
                 .name           = "VP_IDE",
@@ -510,7 +500,8 @@ static ide_pci_device_t via82cxxx_chipsets[] __devinitdata = {
                 .enablebits     = {{0x00,0x00,0x00}, {0x00,0x00,0x00}},
                 .bootable       = ON_BOARD,
                 .host_flags     = IDE_HFLAG_PIO_NO_BLACKLIST
-                                | IDE_HFLAG_PIO_NO_DOWNGRADE,
+                                | IDE_HFLAG_PIO_NO_DOWNGRADE
+                                | IDE_HFLAG_POST_SET_MODE,
                 .pio_mask       = ATA_PIO5,
         }
 };
diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index f759a5397865..7d8873839e21 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -392,6 +392,7 @@ kauai_lookup_timing(struct kauai_timing* table, int cycle_time)
         for (i=0; table[i].cycle_time; i++)
                 if (cycle_time > table[i+1].cycle_time)
                         return table[i].timing_reg;
+        BUG();
         return 0;
 }
 
@@ -529,97 +530,12 @@ pmac_outbsync(ide_drive_t *drive, u8 value, unsigned long port)
 }
 
 /*
- * Send the SET_FEATURE IDE command to the drive and update drive->id with
- * the new state. We currently don't use the generic routine as it used to
- * cause various trouble, especially with older mediabays.
- * This code is sometimes triggering a spurrious interrupt though, I need
- * to sort that out sooner or later and see if I can finally get the
- * common version to work properly in all cases
- */
-static int
-pmac_ide_do_setfeature(ide_drive_t *drive, u8 command)
-{
-        ide_hwif_t *hwif = HWIF(drive);
-        int result = 1;
-        
-        disable_irq_nosync(hwif->irq);
-        udelay(1);
-        SELECT_DRIVE(drive);
-        SELECT_MASK(drive, 0);
-        udelay(1);
-        /* Get rid of pending error state */
-        (void) hwif->INB(IDE_STATUS_REG);
-        /* Timeout bumped for some powerbooks */
-        if (wait_for_ready(drive, 2000)) {
-                /* Timeout bumped for some powerbooks */
-                printk(KERN_ERR "%s: pmac_ide_do_setfeature disk not ready "
-                        "before SET_FEATURE!\n", drive->name);
-                goto out;
-        }
-        udelay(10);
-        hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
-        hwif->OUTB(command, IDE_NSECTOR_REG);
-        hwif->OUTB(SETFEATURES_XFER, IDE_FEATURE_REG);
-        hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
-        udelay(1);
-        /* Timeout bumped for some powerbooks */
-        result = wait_for_ready(drive, 2000);
-        hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
-        if (result)
-                printk(KERN_ERR "%s: pmac_ide_do_setfeature disk not ready "
-                        "after SET_FEATURE !\n", drive->name);
-out:
-        SELECT_MASK(drive, 0);
-        if (result == 0) {
-                drive->id->dma_ultra &= ~0xFF00;
-                drive->id->dma_mword &= ~0x0F00;
-                drive->id->dma_1word &= ~0x0F00;
-                switch(command) {
-                        case XFER_UDMA_7:
-                                drive->id->dma_ultra |= 0x8080; break;
-                        case XFER_UDMA_6:
-                                drive->id->dma_ultra |= 0x4040; break;
-                        case XFER_UDMA_5:
-                                drive->id->dma_ultra |= 0x2020; break;
-                        case XFER_UDMA_4:
-                                drive->id->dma_ultra |= 0x1010; break;
-                        case XFER_UDMA_3:
-                                drive->id->dma_ultra |= 0x0808; break;
-                        case XFER_UDMA_2:
-                                drive->id->dma_ultra |= 0x0404; break;
-                        case XFER_UDMA_1:
-                                drive->id->dma_ultra |= 0x0202; break;
-                        case XFER_UDMA_0:
-                                drive->id->dma_ultra |= 0x0101; break;
-                        case XFER_MW_DMA_2:
-                                drive->id->dma_mword |= 0x0404; break;
-                        case XFER_MW_DMA_1:
-                                drive->id->dma_mword |= 0x0202; break;
-                        case XFER_MW_DMA_0:
-                                drive->id->dma_mword |= 0x0101; break;
-                        case XFER_SW_DMA_2:
-                                drive->id->dma_1word |= 0x0404; break;
-                        case XFER_SW_DMA_1:
-                                drive->id->dma_1word |= 0x0202; break;
-                        case XFER_SW_DMA_0:
-                                drive->id->dma_1word |= 0x0101; break;
-                        default: break;
-                }
-                if (!drive->init_speed)
-                        drive->init_speed = command;
-                drive->current_speed = command;
-        }
-        enable_irq(hwif->irq);
-        return result;
-}
-
-/*
  * Old tuning functions (called on hdparm -p), sets up drive PIO timings
  */
 static void
 pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-        u32 *timings;
+        u32 *timings, t;
         unsigned accessTicks, recTicks;
         unsigned accessTime, recTime;
         pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
@@ -630,6 +546,7 @@ pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
                 
         /* which drive is it ? */
         timings = &pmif->timings[drive->select.b.unit & 0x01];
+        t = *timings;
 
         cycle_time = ide_pio_cycle_time(drive, pio);
 
@@ -637,18 +554,14 @@ pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
         case controller_sh_ata6: {
                 /* 133Mhz cell */
                 u32 tr = kauai_lookup_timing(shasta_pio_timings, cycle_time);
-                if (tr == 0)
-                        return;
-                *timings = ((*timings) & ~TR_133_PIOREG_PIO_MASK) | tr;
+                t = (t & ~TR_133_PIOREG_PIO_MASK) | tr;
                 break;
                 }
         case controller_un_ata6:
         case controller_k2_ata6: {
                 /* 100Mhz cell */
                 u32 tr = kauai_lookup_timing(kauai_pio_timings, cycle_time);
-                if (tr == 0)
-                        return;
-                *timings = ((*timings) & ~TR_100_PIOREG_PIO_MASK) | tr;
+                t = (t & ~TR_100_PIOREG_PIO_MASK) | tr;
                 break;
                 }
         case controller_kl_ata4:
@@ -662,9 +575,9 @@ pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
                 accessTicks = min(accessTicks, 0x1fU);
                 recTicks = SYSCLK_TICKS_66(recTime);
                 recTicks = min(recTicks, 0x1fU);
-                *timings = ((*timings) & ~TR_66_PIO_MASK) |
-                                (accessTicks << TR_66_PIO_ACCESS_SHIFT) |
-                                (recTicks << TR_66_PIO_RECOVERY_SHIFT);
+                t = (t & ~TR_66_PIO_MASK) |
+                        (accessTicks << TR_66_PIO_ACCESS_SHIFT) |
+                        (recTicks << TR_66_PIO_RECOVERY_SHIFT);
                 break;
         default: {
                 /* 33Mhz cell */
@@ -684,11 +597,11 @@ pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
                         recTicks--; /* guess, but it's only for PIO0, so... */
                         ebit = 1;
                 }
-                *timings = ((*timings) & ~TR_33_PIO_MASK) |
+                t = (t & ~TR_33_PIO_MASK) |
                                 (accessTicks << TR_33_PIO_ACCESS_SHIFT) |
                                 (recTicks << TR_33_PIO_RECOVERY_SHIFT);
                 if (ebit)
-                        *timings |= TR_33_PIO_E;
+                        t |= TR_33_PIO_E;
                 break;
                 }
         }
@@ -698,9 +611,7 @@ pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
                 drive->name, pio,  *timings);
 #endif  
 
-        if (pmac_ide_do_setfeature(drive, XFER_PIO_0 + pio))
-                return;
-
+        *timings = t;
         pmac_ide_do_update_timings(drive);
 }
 
@@ -746,8 +657,6 @@ set_timings_udma_ata6(u32 *pio_timings, u32 *ultra_timings, u8 speed)
         if (speed > XFER_UDMA_5 || t == NULL)
                 return 1;
         tr = kauai_lookup_timing(kauai_udma_timings, (int)t->udma);
-        if (tr == 0)
-                return 1;
         *ultra_timings = ((*ultra_timings) & ~TR_100_UDMAREG_UDMA_MASK) | tr;
         *ultra_timings = (*ultra_timings) | TR_100_UDMAREG_UDMA_EN;
 
@@ -766,8 +675,6 @@ set_timings_udma_shasta(u32 *pio_timings, u32 *ultra_timings, u8 speed)
         if (speed > XFER_UDMA_6 || t == NULL)
                 return 1;
         tr = kauai_lookup_timing(shasta_udma133_timings, (int)t->udma);
-        if (tr == 0)
-                return 1;
         *ultra_timings = ((*ultra_timings) & ~TR_133_UDMAREG_UDMA_MASK) | tr;
         *ultra_timings = (*ultra_timings) | TR_133_UDMAREG_UDMA_EN;
 
@@ -777,12 +684,13 @@ set_timings_udma_shasta(u32 *pio_timings, u32 *ultra_timings, u8 speed)
 /*
  * Calculate MDMA timings for all cells
  */
-static int
+static void
 set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
-                        u8 speed, int drive_cycle_time)
+                        u8 speed)
 {
         int cycleTime, accessTime = 0, recTime = 0;
         unsigned accessTicks, recTicks;
+        struct hd_driveid *id = drive->id;
         struct mdma_timings_t* tm = NULL;
         int i;
 
@@ -792,11 +700,14 @@ set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
                 case 1: cycleTime = 150; break;
                 case 2: cycleTime = 120; break;
                 default:
-                        return 1;
+                        BUG();
+                        break;
         }
-        /* Adjust for drive */
-        if (drive_cycle_time && drive_cycle_time > cycleTime)
-                cycleTime = drive_cycle_time;
+
+        /* Check if drive provides explicit DMA cycle time */
+        if ((id->field_valid & 2) && id->eide_dma_time)
+                cycleTime = max_t(int, id->eide_dma_time, cycleTime);
+
         /* OHare limits according to some old Apple sources */  
         if ((intf_type == controller_ohare) && (cycleTime < 150))
                 cycleTime = 150;
@@ -824,8 +735,6 @@ set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
                                 break;
                         i++;
                 }
-                if (i < 0)
-                        return 1;
                 cycleTime = tm[i].cycleTime;
                 accessTime = tm[i].accessTime;
                 recTime = tm[i].recoveryTime;
@@ -839,8 +748,6 @@ set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
         case controller_sh_ata6: {
                 /* 133Mhz cell */
                 u32 tr = kauai_lookup_timing(shasta_mdma_timings, cycleTime);
-                if (tr == 0)
-                        return 1;
                 *timings = ((*timings) & ~TR_133_PIOREG_MDMA_MASK) | tr;
                 *timings2 = (*timings2) & ~TR_133_UDMAREG_UDMA_EN;
                 }
@@ -848,8 +755,6 @@ set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
         case controller_k2_ata6: {
                 /* 100Mhz cell */
                 u32 tr = kauai_lookup_timing(kauai_mdma_timings, cycleTime);
-                if (tr == 0)
-                        return 1;
                 *timings = ((*timings) & ~TR_100_PIOREG_MDMA_MASK) | tr;
                 *timings2 = (*timings2) & ~TR_100_UDMAREG_UDMA_EN;
                 }
@@ -911,30 +816,23 @@ set_timings_mdma(ide_drive_t *drive, int intf_type, u32 *timings, u32 *timings2,
         printk(KERN_ERR "%s: Set MDMA timing for mode %d, reg: 0x%08x\n",
                 drive->name, speed & 0xf,  *timings);
 #endif  
-        return 0;
 }
 #endif /* #ifdef CONFIG_BLK_DEV_IDEDMA_PMAC */
 
-/* 
- * Speedproc. This function is called by the core to set any of the standard
- * DMA timing (MDMA or UDMA) to both the drive and the controller.
- * You may notice we don't use this function on normal "dma check" operation,
- * our dedicated function is more precise as it uses the drive provided
- * cycle time value. We should probably fix this one to deal with that too...
- */
-static int pmac_ide_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void pmac_ide_set_dma_mode(ide_drive_t *drive, const u8 speed)
 {
         int unit = (drive->select.b.unit & 0x01);
         int ret = 0;
         pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)HWIF(drive)->hwif_data;
-        u32 *timings, *timings2;
+        u32 *timings, *timings2, tl[2];
 
-        if (pmif == NULL)
-                return 1;
-                
         timings = &pmif->timings[unit];
         timings2 = &pmif->timings[unit+2];
-        
+
+        /* Copy timings to local image */
+        tl[0] = *timings;
+        tl[1] = *timings2;
+
         switch(speed) {
 #ifdef CONFIG_BLK_DEV_IDEDMA_PMAC
                 case XFER_UDMA_6:
@@ -945,38 +843,36 @@ static int pmac_ide_tune_chipset(ide_drive_t *drive, const u8 speed)
                 case XFER_UDMA_1:
                 case XFER_UDMA_0:
                         if (pmif->kind == controller_kl_ata4)
-                                ret = set_timings_udma_ata4(timings, speed);
+                                ret = set_timings_udma_ata4(&tl[0], speed);
                         else if (pmif->kind == controller_un_ata6
                                  || pmif->kind == controller_k2_ata6)
-                                ret = set_timings_udma_ata6(timings, timings2, speed);
+                                ret = set_timings_udma_ata6(&tl[0], &tl[1], speed);
                         else if (pmif->kind == controller_sh_ata6)
-                                ret = set_timings_udma_shasta(timings, timings2, speed);
+                                ret = set_timings_udma_shasta(&tl[0], &tl[1], speed);
                         else
-                                ret = 1;                
+                                ret = 1;
                         break;
                 case XFER_MW_DMA_2:
                 case XFER_MW_DMA_1:
                 case XFER_MW_DMA_0:
-                        ret = set_timings_mdma(drive, pmif->kind, timings, timings2, speed, 0);
+                        set_timings_mdma(drive, pmif->kind, &tl[0], &tl[1], speed);
                         break;
                 case XFER_SW_DMA_2:
                 case XFER_SW_DMA_1:
                 case XFER_SW_DMA_0:
-                        return 1;
+                        return;
 #endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
                 default:
                         ret = 1;
         }
         if (ret)
-                return ret;
+                return;
 
-        ret = pmac_ide_do_setfeature(drive, speed);
-        if (ret)
-                return ret;
-                
-        pmac_ide_do_update_timings(drive);      
+        /* Apply timings to controller */
+        *timings = tl[0];
+        *timings2 = tl[1];
 
-        return 0;
+        pmac_ide_do_update_timings(drive);      
 }
 
 /*
@@ -1236,6 +1132,10 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
         hwif->cbl = pmif->cable_80 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
         hwif->drives[0].unmask = 1;
         hwif->drives[1].unmask = 1;
+        hwif->drives[0].autotune = IDE_TUNE_AUTO;
+        hwif->drives[1].autotune = IDE_TUNE_AUTO;
+        hwif->host_flags = IDE_HFLAG_SET_PIO_MODE_KEEP_DMA |
+                           IDE_HFLAG_POST_SET_MODE;
         hwif->pio_mask = ATA_PIO4;
         hwif->set_pio_mode = pmac_ide_set_pio_mode;
         if (pmif->kind == controller_un_ata6
@@ -1244,7 +1144,7 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
                 hwif->selectproc = pmac_ide_kauai_selectproc;
         else
                 hwif->selectproc = pmac_ide_selectproc;
-        hwif->speedproc = pmac_ide_tune_chipset;
+        hwif->set_dma_mode = pmac_ide_set_dma_mode;
 
         printk(KERN_INFO "ide%d: Found Apple %s controller, bus ID %d%s, irq %d\n",
                hwif->index, model_name[pmif->kind], pmif->aapl_bus_id,
@@ -1679,138 +1579,16 @@ pmac_ide_destroy_dmatable (ide_drive_t *drive)
 }
 
 /*
- * Pick up best MDMA timing for the drive and apply it
- */
-static int
-pmac_ide_mdma_enable(ide_drive_t *drive, u16 mode)
-{
-        ide_hwif_t *hwif = HWIF(drive);
-        pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
-        int drive_cycle_time;
-        struct hd_driveid *id = drive->id;
-        u32 *timings, *timings2;
-        u32 timing_local[2];
-        int ret;
-
-        /* which drive is it ? */
-        timings = &pmif->timings[drive->select.b.unit & 0x01];
-        timings2 = &pmif->timings[(drive->select.b.unit & 0x01) + 2];
-
-        /* Check if drive provide explicit cycle time */
-        if ((id->field_valid & 2) && (id->eide_dma_time))
-                drive_cycle_time = id->eide_dma_time;
-        else
-                drive_cycle_time = 0;
-
-        /* Copy timings to local image */
-        timing_local[0] = *timings;
-        timing_local[1] = *timings2;
-
-        /* Calculate controller timings */
-        ret = set_timings_mdma( drive, pmif->kind,
-                                &timing_local[0],
-                                &timing_local[1],
-                                mode,
-                                drive_cycle_time);
-        if (ret)
-                return 0;
-
-        /* Set feature on drive */
-        printk(KERN_INFO "%s: Enabling MultiWord DMA %d\n", drive->name, mode & 0xf);
-        ret = pmac_ide_do_setfeature(drive, mode);
-        if (ret) {
-                printk(KERN_WARNING "%s: Failed !\n", drive->name);
-                return 0;
-        }
-
-        /* Apply timings to controller */
-        *timings = timing_local[0];
-        *timings2 = timing_local[1];
-
-        return 1;
-}
-
-/*
- * Pick up best UDMA timing for the drive and apply it
- */
-static int
-pmac_ide_udma_enable(ide_drive_t *drive, u16 mode)
-{
-        ide_hwif_t *hwif = HWIF(drive);
-        pmac_ide_hwif_t* pmif = (pmac_ide_hwif_t *)hwif->hwif_data;
-        u32 *timings, *timings2;
-        u32 timing_local[2];
-        int ret;
-                
-        /* which drive is it ? */
-        timings = &pmif->timings[drive->select.b.unit & 0x01];
-        timings2 = &pmif->timings[(drive->select.b.unit & 0x01) + 2];
-
-        /* Copy timings to local image */
-        timing_local[0] = *timings;
-        timing_local[1] = *timings2;
-        
-        /* Calculate timings for interface */
-        if (pmif->kind == controller_un_ata6
-            || pmif->kind == controller_k2_ata6)
-                ret = set_timings_udma_ata6(    &timing_local[0],
-                                                &timing_local[1],
-                                                mode);
-        else if (pmif->kind == controller_sh_ata6)
-                ret = set_timings_udma_shasta(  &timing_local[0],
-                                                &timing_local[1],
-                                                mode);
-        else
-                ret = set_timings_udma_ata4(&timing_local[0], mode);
-        if (ret)
-                return 0;
-                
-        /* Set feature on drive */
-        printk(KERN_INFO "%s: Enabling Ultra DMA %d\n", drive->name, mode & 0x0f);
-        ret = pmac_ide_do_setfeature(drive, mode);
-        if (ret) {
-                printk(KERN_WARNING "%s: Failed !\n", drive->name);
-                return 0;
-        }
-
-        /* Apply timings to controller */
-        *timings = timing_local[0];
-        *timings2 = timing_local[1];
-
-        return 1;
-}
-
-/*
  * Check what is the best DMA timing setting for the drive and
  * call appropriate functions to apply it.
  */
 static int
 pmac_ide_dma_check(ide_drive_t *drive)
 {
-        struct hd_driveid *id = drive->id;
-        ide_hwif_t *hwif = HWIF(drive);
-        int enable = 1;
-        drive->using_dma = 0;
-        
-        if (drive->media == ide_floppy)
-                enable = 0;
-        if (((id->capability & 1) == 0) && !__ide_dma_good_drive(drive))
-                enable = 0;
-        if (__ide_dma_bad_drive(drive))
-                enable = 0;
-
-        if (enable) {
-                u8 mode = ide_max_dma_mode(drive);
-
-                if (mode >= XFER_UDMA_0)
-                        drive->using_dma = pmac_ide_udma_enable(drive, mode);
-                else if (mode >= XFER_MW_DMA_0)
-                        drive->using_dma = pmac_ide_mdma_enable(drive, mode);
-                hwif->OUTB(0, IDE_CONTROL_REG);
-                /* Apply settings to controller */
-                pmac_ide_do_update_timings(drive);
-        }
-        return 0;
+        if (ide_tune_dma(drive))
+                return 0;
+
+        return -1;
 }
 
 /*
@@ -2044,7 +1822,10 @@ pmac_ide_setup_dma(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
                         hwif->mwdma_mask = 0x07;
                         hwif->swdma_mask = 0x00;
                         break;
-        }       
+        }
+
+        hwif->autodma = 1;
+        hwif->drives[1].autodma = hwif->drives[0].autodma = hwif->autodma;
 }
 
 #endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
diff --git a/include/linux/ide.h b/include/linux/ide.h
index 85d448b4abec..02a27e8cbad2 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -681,7 +681,7 @@ typedef struct hwif_s {
         u8 straight8;   /* Alan's straight 8 check */
         u8 bus_state;   /* power state of the IDE bus */
 
-        u8 host_flags;
+        u16 host_flags;
 
         u8 pio_mask;
 
@@ -702,10 +702,10 @@ typedef struct hwif_s {
 #if 0
         ide_hwif_ops_t  *hwifops;
 #else
-        /* routine to set PIO mode for drives */
+        /* routine to program host for PIO mode */
         void    (*set_pio_mode)(ide_drive_t *, const u8);
-        /* routine to retune DMA modes for drives */
-        int     (*speedproc)(ide_drive_t *, const u8);
+        /* routine to program host for DMA mode */
+        void    (*set_dma_mode)(ide_drive_t *, const u8);
         /* tweaks hardware to select drive */
         void    (*selectproc)(ide_drive_t *);
         /* chipset polling based on hba specifics */
@@ -1079,16 +1079,7 @@ extern void ide_fix_driveid(struct hd_driveid *);
  */
 extern void ide_fixstring(u8 *, const int, const int);
 
-/*
- * This routine busy-waits for the drive status to be not "busy".
- * It then checks the status for all of the "good" bits and none
- * of the "bad" bits, and if all is okay it returns 0.  All other
- * cases return 1 after doing "*startstop = ide_error()", and the
- * caller should return the updated value of "startstop" in this case.
- * "startstop" is unchanged when the function returns 0;
- * (startstop, drive, good, bad, timeout)
- */
-extern int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
+int ide_wait_stat(ide_startstop_t *, ide_drive_t *, u8, u8, unsigned long);
 
 /*
  * Start a reset operation for an IDE interface.
@@ -1162,7 +1153,6 @@ extern void SELECT_MASK(ide_drive_t *, int);
 extern void QUIRK_LIST(ide_drive_t *);
 
 extern int drive_is_ready(ide_drive_t *);
-extern int wait_for_ready(ide_drive_t *, int /* timeout */);
 
 /*
  * taskfile io for disks for now...and builds request from ide_ioctl
@@ -1262,6 +1252,15 @@ enum {
         IDE_HFLAG_ABUSE_FAST_DEVSEL     = (1 << 5),
         /* use 100-102 and 200-202 PIO values to set DMA modes */
         IDE_HFLAG_ABUSE_DMA_MODES       = (1 << 6),
+        /*
+         * keep DMA setting when programming PIO mode, may be used only
+         * for hosts which have separate PIO and DMA timings (ie. PMAC)
+         */
+        IDE_HFLAG_SET_PIO_MODE_KEEP_DMA = (1 << 7),
+        /* program host for the transfer mode after programming device */
+        IDE_HFLAG_POST_SET_MODE         = (1 << 8),
+        /* don't program host/device for the transfer mode ("smart" hosts) */
+        IDE_HFLAG_NO_SET_MODE           = (1 << 9),
 };
 
 typedef struct ide_pci_device_s {
@@ -1278,7 +1277,7 @@ typedef struct ide_pci_device_s {
         u8                      bootable;
         unsigned int            extra;
         struct ide_pci_device_s *next;
-        u8                      host_flags;
+        u16                     host_flags;
         u8                      pio_mask;
         u8                      udma_mask;
 } ide_pci_device_t;
@@ -1301,7 +1300,6 @@ int ide_in_drive_list(struct hd_driveid *, const struct drive_list_entry *);
 
 #ifdef CONFIG_BLK_DEV_IDEDMA
 int __ide_dma_bad_drive(ide_drive_t *);
-int __ide_dma_good_drive(ide_drive_t *);
 
 u8 ide_find_dma_mode(ide_drive_t *, u8);
 
@@ -1420,6 +1418,9 @@ unsigned int ide_pio_cycle_time(ide_drive_t *, u8);
 u8 ide_get_best_pio_mode(ide_drive_t *, u8, u8);
 extern const ide_pio_timings_t ide_pio_timings[6];
 
+int ide_set_pio_mode(ide_drive_t *, u8);
+int ide_set_dma_mode(ide_drive_t *, u8);
+
 void ide_set_pio(ide_drive_t *, u8);
 
 static inline void ide_set_max_pio(ide_drive_t *drive)