diff options
44 files changed, 227 insertions, 120 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 141c22269eba..c3c5842402df 100644 --- a/MAINTAINERS +++ b/MAINTAINERS | |||
@@ -1889,6 +1889,11 @@ L: linux-kernel@vger.kernel.org | |||
1889 | W: http://www.atnf.csiro.au/~rgooch/linux/kernel-patches.html | 1889 | W: http://www.atnf.csiro.au/~rgooch/linux/kernel-patches.html |
1890 | S: Maintained | 1890 | S: Maintained |
1891 | 1891 | ||
1892 | MULTIMEDIA CARD SUBSYSTEM | ||
1893 | P: Russell King | ||
1894 | M: rmk+mmc@arm.linux.org.uk | ||
1895 | S: Maintained | ||
1896 | |||
1892 | MULTISOUND SOUND DRIVER | 1897 | MULTISOUND SOUND DRIVER |
1893 | P: Andrew Veliath | 1898 | P: Andrew Veliath |
1894 | M: andrewtv@usa.net | 1899 | M: andrewtv@usa.net |
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 5d3acff8c596..d22f38b957db 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug | |||
@@ -101,7 +101,7 @@ config DEBUG_S3C2410_UART | |||
101 | help | 101 | help |
102 | Choice for UART for kernel low-level using S3C2410 UARTS, | 102 | Choice for UART for kernel low-level using S3C2410 UARTS, |
103 | should be between zero and two. The port must have been | 103 | should be between zero and two. The port must have been |
104 | initalised by the boot-loader before use. | 104 | initialised by the boot-loader before use. |
105 | 105 | ||
106 | The uncompressor code port configuration is now handled | 106 | The uncompressor code port configuration is now handled |
107 | by CONFIG_S3C2410_LOWLEVEL_UART_PORT. | 107 | by CONFIG_S3C2410_LOWLEVEL_UART_PORT. |
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig index 2a39f9e481ad..3b23f43cb160 100644 --- a/arch/arm/mach-ixp4xx/Kconfig +++ b/arch/arm/mach-ixp4xx/Kconfig | |||
@@ -141,7 +141,7 @@ config IXP4XX_INDIRECT_PCI | |||
141 | 2) If > 64MB of memory space is required, the IXP4xx can be | 141 | 2) If > 64MB of memory space is required, the IXP4xx can be |
142 | configured to use indirect registers to access PCI This allows | 142 | configured to use indirect registers to access PCI This allows |
143 | for up to 128MB (0x48000000 to 0x4fffffff) of memory on the bus. | 143 | for up to 128MB (0x48000000 to 0x4fffffff) of memory on the bus. |
144 | The disadvantadge of this is that every PCI access requires | 144 | The disadvantage of this is that every PCI access requires |
145 | three local register accesses plus a spinlock, but in some | 145 | three local register accesses plus a spinlock, but in some |
146 | cases the performance hit is acceptable. In addition, you cannot | 146 | cases the performance hit is acceptable. In addition, you cannot |
147 | mmap() PCI devices in this case due to the indirect nature | 147 | mmap() PCI devices in this case due to the indirect nature |
diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c index 02e188d98e7d..b307f11951df 100644 --- a/arch/arm/mach-pxa/mainstone.c +++ b/arch/arm/mach-pxa/mainstone.c | |||
@@ -493,6 +493,7 @@ static void __init mainstone_map_io(void) | |||
493 | MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)") | 493 | MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)") |
494 | /* Maintainer: MontaVista Software Inc. */ | 494 | /* Maintainer: MontaVista Software Inc. */ |
495 | .phys_io = 0x40000000, | 495 | .phys_io = 0x40000000, |
496 | .boot_params = 0xa0000100, /* BLOB boot parameter setting */ | ||
496 | .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, | 497 | .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, |
497 | .map_io = mainstone_map_io, | 498 | .map_io = mainstone_map_io, |
498 | .init_irq = mainstone_init_irq, | 499 | .init_irq = mainstone_init_irq, |
diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index ce7d81000695..970f98dadffc 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig | |||
@@ -170,7 +170,7 @@ config S3C2410_PM_DEBUG | |||
170 | depends on ARCH_S3C2410 && PM | 170 | depends on ARCH_S3C2410 && PM |
171 | help | 171 | help |
172 | Say Y here if you want verbose debugging from the PM Suspend and | 172 | Say Y here if you want verbose debugging from the PM Suspend and |
173 | Resume code. See `Documentation/arm/Samsing-S3C24XX/Suspend.txt` | 173 | Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt> |
174 | for more information. | 174 | for more information. |
175 | 175 | ||
176 | config S3C2410_PM_CHECK | 176 | config S3C2410_PM_CHECK |
diff --git a/arch/mips/au1000/common/prom.c b/arch/mips/au1000/common/prom.c index 9c171afd9a53..ae7d8c57bf3f 100644 --- a/arch/mips/au1000/common/prom.c +++ b/arch/mips/au1000/common/prom.c | |||
@@ -1,10 +1,9 @@ | |||
1 | /* | 1 | /* |
2 | * | 2 | * |
3 | * BRIEF MODULE DESCRIPTION | 3 | * BRIEF MODULE DESCRIPTION |
4 | * PROM library initialisation code, assuming a version of | 4 | * PROM library initialisation code, assuming YAMON is the boot loader. |
5 | * pmon is the boot code. | ||
6 | * | 5 | * |
7 | * Copyright 2000,2001 MontaVista Software Inc. | 6 | * Copyright 2000, 2001, 2006 MontaVista Software Inc. |
8 | * Author: MontaVista Software, Inc. | 7 | * Author: MontaVista Software, Inc. |
9 | * ppopov@mvista.com or source@mvista.com | 8 | * ppopov@mvista.com or source@mvista.com |
10 | * | 9 | * |
@@ -49,9 +48,9 @@ extern char **prom_argv, **prom_envp; | |||
49 | 48 | ||
50 | typedef struct | 49 | typedef struct |
51 | { | 50 | { |
52 | char *name; | 51 | char *name; |
53 | /* char *val; */ | 52 | char *val; |
54 | }t_env_var; | 53 | } t_env_var; |
55 | 54 | ||
56 | 55 | ||
57 | char * prom_getcmdline(void) | 56 | char * prom_getcmdline(void) |
@@ -85,21 +84,16 @@ char *prom_getenv(char *envname) | |||
85 | { | 84 | { |
86 | /* | 85 | /* |
87 | * Return a pointer to the given environment variable. | 86 | * Return a pointer to the given environment variable. |
88 | * Environment variables are stored in the form of "memsize=64". | ||
89 | */ | 87 | */ |
90 | 88 | ||
91 | t_env_var *env = (t_env_var *)prom_envp; | 89 | t_env_var *env = (t_env_var *)prom_envp; |
92 | int i; | ||
93 | |||
94 | i = strlen(envname); | ||
95 | 90 | ||
96 | while(env->name) { | 91 | while (env->name) { |
97 | if(strncmp(envname, env->name, i) == 0) { | 92 | if (strcmp(envname, env->name) == 0) |
98 | return(env->name + strlen(envname) + 1); | 93 | return env->val; |
99 | } | ||
100 | env++; | 94 | env++; |
101 | } | 95 | } |
102 | return(NULL); | 96 | return NULL; |
103 | } | 97 | } |
104 | 98 | ||
105 | inline unsigned char str2hexnum(unsigned char c) | 99 | inline unsigned char str2hexnum(unsigned char c) |
diff --git a/arch/mips/au1000/common/sleeper.S b/arch/mips/au1000/common/sleeper.S index 44dac3b0df3b..683d9da84b66 100644 --- a/arch/mips/au1000/common/sleeper.S +++ b/arch/mips/au1000/common/sleeper.S | |||
@@ -112,6 +112,11 @@ sdsleep: | |||
112 | mtc0 k0, CP0_PAGEMASK | 112 | mtc0 k0, CP0_PAGEMASK |
113 | lw k0, 0x14(sp) | 113 | lw k0, 0x14(sp) |
114 | mtc0 k0, CP0_CONFIG | 114 | mtc0 k0, CP0_CONFIG |
115 | |||
116 | /* We need to catch the ealry Alchemy SOCs with | ||
117 | * the write-only Config[OD] bit and set it back to one... | ||
118 | */ | ||
119 | jal au1x00_fixup_config_od | ||
115 | lw $1, PT_R1(sp) | 120 | lw $1, PT_R1(sp) |
116 | lw $2, PT_R2(sp) | 121 | lw $2, PT_R2(sp) |
117 | lw $3, PT_R3(sp) | 122 | lw $3, PT_R3(sp) |
diff --git a/arch/mips/ddb5xxx/ddb5476/dbg_io.c b/arch/mips/ddb5xxx/ddb5476/dbg_io.c index 85e9e5013679..f2296a999953 100644 --- a/arch/mips/ddb5xxx/ddb5476/dbg_io.c +++ b/arch/mips/ddb5xxx/ddb5476/dbg_io.c | |||
@@ -86,7 +86,7 @@ void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) | |||
86 | /* disable interrupts */ | 86 | /* disable interrupts */ |
87 | UART16550_WRITE(OFS_INTR_ENABLE, 0); | 87 | UART16550_WRITE(OFS_INTR_ENABLE, 0); |
88 | 88 | ||
89 | /* set up buad rate */ | 89 | /* set up baud rate */ |
90 | { | 90 | { |
91 | uint32 divisor; | 91 | uint32 divisor; |
92 | 92 | ||
diff --git a/arch/mips/ddb5xxx/ddb5477/kgdb_io.c b/arch/mips/ddb5xxx/ddb5477/kgdb_io.c index 1d18d590495b..385bbdb10170 100644 --- a/arch/mips/ddb5xxx/ddb5477/kgdb_io.c +++ b/arch/mips/ddb5xxx/ddb5477/kgdb_io.c | |||
@@ -86,7 +86,7 @@ void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) | |||
86 | /* disable interrupts */ | 86 | /* disable interrupts */ |
87 | UART16550_WRITE(OFS_INTR_ENABLE, 0); | 87 | UART16550_WRITE(OFS_INTR_ENABLE, 0); |
88 | 88 | ||
89 | /* set up buad rate */ | 89 | /* set up baud rate */ |
90 | { | 90 | { |
91 | uint32 divisor; | 91 | uint32 divisor; |
92 | 92 | ||
diff --git a/arch/mips/gt64120/ev64120/serialGT.c b/arch/mips/gt64120/ev64120/serialGT.c index 16e34a546e54..8f0d835491ff 100644 --- a/arch/mips/gt64120/ev64120/serialGT.c +++ b/arch/mips/gt64120/ev64120/serialGT.c | |||
@@ -149,7 +149,7 @@ void serial_set(int channel, unsigned long baud) | |||
149 | #else | 149 | #else |
150 | /* | 150 | /* |
151 | * Note: Set baud rate, hardcoded here for rate of 115200 | 151 | * Note: Set baud rate, hardcoded here for rate of 115200 |
152 | * since became unsure of above "buad rate" algorithm (??). | 152 | * since became unsure of above "baud rate" algorithm (??). |
153 | */ | 153 | */ |
154 | outreg(channel, LCR, 0x83); | 154 | outreg(channel, LCR, 0x83); |
155 | outreg(channel, DLM, 0x00); // See note above | 155 | outreg(channel, DLM, 0x00); // See note above |
diff --git a/arch/mips/gt64120/momenco_ocelot/dbg_io.c b/arch/mips/gt64120/momenco_ocelot/dbg_io.c index 8720bccfdea2..f0a6a38fcf4d 100644 --- a/arch/mips/gt64120/momenco_ocelot/dbg_io.c +++ b/arch/mips/gt64120/momenco_ocelot/dbg_io.c | |||
@@ -73,7 +73,7 @@ void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) | |||
73 | /* disable interrupts */ | 73 | /* disable interrupts */ |
74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); | 74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); |
75 | 75 | ||
76 | /* set up buad rate */ | 76 | /* set up baud rate */ |
77 | { | 77 | { |
78 | uint32 divisor; | 78 | uint32 divisor; |
79 | 79 | ||
diff --git a/arch/mips/ite-boards/generic/dbg_io.c b/arch/mips/ite-boards/generic/dbg_io.c index c4f8530fd07e..6a7ccaf93502 100644 --- a/arch/mips/ite-boards/generic/dbg_io.c +++ b/arch/mips/ite-boards/generic/dbg_io.c | |||
@@ -72,7 +72,7 @@ void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) | |||
72 | /* disable interrupts */ | 72 | /* disable interrupts */ |
73 | UART16550_WRITE(OFS_INTR_ENABLE, 0); | 73 | UART16550_WRITE(OFS_INTR_ENABLE, 0); |
74 | 74 | ||
75 | /* set up buad rate */ | 75 | /* set up baud rate */ |
76 | { | 76 | { |
77 | uint32 divisor; | 77 | uint32 divisor; |
78 | 78 | ||
diff --git a/arch/mips/kernel/cpu-bugs64.c b/arch/mips/kernel/cpu-bugs64.c index 47a087b6c11b..d268827c62bd 100644 --- a/arch/mips/kernel/cpu-bugs64.c +++ b/arch/mips/kernel/cpu-bugs64.c | |||
@@ -206,7 +206,7 @@ static inline void check_daddi(void) | |||
206 | "daddi %0, %1, %3\n\t" | 206 | "daddi %0, %1, %3\n\t" |
207 | ".set pop" | 207 | ".set pop" |
208 | : "=r" (v), "=&r" (tmp) | 208 | : "=r" (v), "=&r" (tmp) |
209 | : "I" (0xffffffffffffdb9a), "I" (0x1234)); | 209 | : "I" (0xffffffffffffdb9aUL), "I" (0x1234)); |
210 | set_except_vector(12, handler); | 210 | set_except_vector(12, handler); |
211 | local_irq_restore(flags); | 211 | local_irq_restore(flags); |
212 | 212 | ||
@@ -224,7 +224,7 @@ static inline void check_daddi(void) | |||
224 | "dsrl %1, %1, 1\n\t" | 224 | "dsrl %1, %1, 1\n\t" |
225 | "daddi %0, %1, %3" | 225 | "daddi %0, %1, %3" |
226 | : "=r" (v), "=&r" (tmp) | 226 | : "=r" (v), "=&r" (tmp) |
227 | : "I" (0xffffffffffffdb9a), "I" (0x1234)); | 227 | : "I" (0xffffffffffffdb9aUL), "I" (0x1234)); |
228 | set_except_vector(12, handler); | 228 | set_except_vector(12, handler); |
229 | local_irq_restore(flags); | 229 | local_irq_restore(flags); |
230 | 230 | ||
@@ -280,7 +280,7 @@ static inline void check_daddiu(void) | |||
280 | "daddu %1, %2\n\t" | 280 | "daddu %1, %2\n\t" |
281 | ".set pop" | 281 | ".set pop" |
282 | : "=&r" (v), "=&r" (w), "=&r" (tmp) | 282 | : "=&r" (v), "=&r" (w), "=&r" (tmp) |
283 | : "I" (0xffffffffffffdb9a), "I" (0x1234)); | 283 | : "I" (0xffffffffffffdb9aUL), "I" (0x1234)); |
284 | 284 | ||
285 | if (v == w) { | 285 | if (v == w) { |
286 | printk("no.\n"); | 286 | printk("no.\n"); |
@@ -296,7 +296,7 @@ static inline void check_daddiu(void) | |||
296 | "addiu %1, $0, %4\n\t" | 296 | "addiu %1, $0, %4\n\t" |
297 | "daddu %1, %2" | 297 | "daddu %1, %2" |
298 | : "=&r" (v), "=&r" (w), "=&r" (tmp) | 298 | : "=&r" (v), "=&r" (w), "=&r" (tmp) |
299 | : "I" (0xffffffffffffdb9a), "I" (0x1234)); | 299 | : "I" (0xffffffffffffdb9aUL), "I" (0x1234)); |
300 | 300 | ||
301 | if (v == w) { | 301 | if (v == w) { |
302 | printk("yes.\n"); | 302 | printk("yes.\n"); |
diff --git a/arch/mips/kernel/cpu-probe.c b/arch/mips/kernel/cpu-probe.c index bef3e2dc7c52..8c2c359a05f4 100644 --- a/arch/mips/kernel/cpu-probe.c +++ b/arch/mips/kernel/cpu-probe.c | |||
@@ -655,7 +655,7 @@ static inline void cpu_probe_sibyte(struct cpuinfo_mips *c) | |||
655 | case PRID_IMP_SB1: | 655 | case PRID_IMP_SB1: |
656 | c->cputype = CPU_SB1; | 656 | c->cputype = CPU_SB1; |
657 | /* FPU in pass1 is known to have issues. */ | 657 | /* FPU in pass1 is known to have issues. */ |
658 | if ((c->processor_id & 0xff) < 0x20) | 658 | if ((c->processor_id & 0xff) < 0x02) |
659 | c->options &= ~(MIPS_CPU_FPU | MIPS_CPU_32FPR); | 659 | c->options &= ~(MIPS_CPU_FPU | MIPS_CPU_32FPR); |
660 | break; | 660 | break; |
661 | case PRID_IMP_SB1A: | 661 | case PRID_IMP_SB1A: |
diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c index e54a7f442f8a..d7bf0215bc1d 100644 --- a/arch/mips/kernel/module.c +++ b/arch/mips/kernel/module.c | |||
@@ -288,6 +288,9 @@ int apply_relocate(Elf_Shdr *sechdrs, const char *strtab, | |||
288 | sym = (Elf_Sym *)sechdrs[symindex].sh_addr | 288 | sym = (Elf_Sym *)sechdrs[symindex].sh_addr |
289 | + ELF_MIPS_R_SYM(rel[i]); | 289 | + ELF_MIPS_R_SYM(rel[i]); |
290 | if (!sym->st_value) { | 290 | if (!sym->st_value) { |
291 | /* Ignore unresolved weak symbol */ | ||
292 | if (ELF_ST_BIND(sym->st_info) == STB_WEAK) | ||
293 | continue; | ||
291 | printk(KERN_WARNING "%s: Unknown symbol %s\n", | 294 | printk(KERN_WARNING "%s: Unknown symbol %s\n", |
292 | me->name, strtab + sym->st_name); | 295 | me->name, strtab + sym->st_name); |
293 | return -ENOENT; | 296 | return -ENOENT; |
@@ -325,6 +328,9 @@ int apply_relocate_add(Elf_Shdr *sechdrs, const char *strtab, | |||
325 | sym = (Elf_Sym *)sechdrs[symindex].sh_addr | 328 | sym = (Elf_Sym *)sechdrs[symindex].sh_addr |
326 | + ELF_MIPS_R_SYM(rel[i]); | 329 | + ELF_MIPS_R_SYM(rel[i]); |
327 | if (!sym->st_value) { | 330 | if (!sym->st_value) { |
331 | /* Ignore unresolved weak symbol */ | ||
332 | if (ELF_ST_BIND(sym->st_info) == STB_WEAK) | ||
333 | continue; | ||
328 | printk(KERN_WARNING "%s: Unknown symbol %s\n", | 334 | printk(KERN_WARNING "%s: Unknown symbol %s\n", |
329 | me->name, strtab + sym->st_name); | 335 | me->name, strtab + sym->st_name); |
330 | return -ENOENT; | 336 | return -ENOENT; |
diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S index b53a9207f530..8efb23a84131 100644 --- a/arch/mips/kernel/scall64-o32.S +++ b/arch/mips/kernel/scall64-o32.S | |||
@@ -209,7 +209,7 @@ sys_call_table: | |||
209 | PTR sys_fork | 209 | PTR sys_fork |
210 | PTR sys_read | 210 | PTR sys_read |
211 | PTR sys_write | 211 | PTR sys_write |
212 | PTR sys_open /* 4005 */ | 212 | PTR compat_sys_open /* 4005 */ |
213 | PTR sys_close | 213 | PTR sys_close |
214 | PTR sys_waitpid | 214 | PTR sys_waitpid |
215 | PTR sys_creat | 215 | PTR sys_creat |
diff --git a/arch/mips/kernel/setup.c b/arch/mips/kernel/setup.c index bcf1b10e518f..397a70e651b5 100644 --- a/arch/mips/kernel/setup.c +++ b/arch/mips/kernel/setup.c | |||
@@ -246,7 +246,7 @@ static inline int parse_rd_cmdline(unsigned long* rd_start, unsigned long* rd_en | |||
246 | #ifdef CONFIG_64BIT | 246 | #ifdef CONFIG_64BIT |
247 | /* HACK: Guess if the sign extension was forgotten */ | 247 | /* HACK: Guess if the sign extension was forgotten */ |
248 | if (start > 0x0000000080000000 && start < 0x00000000ffffffff) | 248 | if (start > 0x0000000080000000 && start < 0x00000000ffffffff) |
249 | start |= 0xffffffff00000000; | 249 | start |= 0xffffffff00000000UL; |
250 | #endif | 250 | #endif |
251 | 251 | ||
252 | end = start + size; | 252 | end = start + size; |
@@ -355,8 +355,6 @@ static inline void bootmem_init(void) | |||
355 | } | 355 | } |
356 | #endif | 356 | #endif |
357 | 357 | ||
358 | memory_present(0, first_usable_pfn, max_low_pfn); | ||
359 | |||
360 | /* Initialize the boot-time allocator with low memory only. */ | 358 | /* Initialize the boot-time allocator with low memory only. */ |
361 | bootmap_size = init_bootmem(first_usable_pfn, max_low_pfn); | 359 | bootmap_size = init_bootmem(first_usable_pfn, max_low_pfn); |
362 | 360 | ||
@@ -410,6 +408,7 @@ static inline void bootmem_init(void) | |||
410 | 408 | ||
411 | /* Register lowmem ranges */ | 409 | /* Register lowmem ranges */ |
412 | free_bootmem(PFN_PHYS(curr_pfn), PFN_PHYS(size)); | 410 | free_bootmem(PFN_PHYS(curr_pfn), PFN_PHYS(size)); |
411 | memory_present(0, curr_pfn, curr_pfn + size - 1); | ||
413 | } | 412 | } |
414 | 413 | ||
415 | /* Reserve the bootmap memory. */ | 414 | /* Reserve the bootmap memory. */ |
@@ -419,17 +418,20 @@ static inline void bootmem_init(void) | |||
419 | #ifdef CONFIG_BLK_DEV_INITRD | 418 | #ifdef CONFIG_BLK_DEV_INITRD |
420 | initrd_below_start_ok = 1; | 419 | initrd_below_start_ok = 1; |
421 | if (initrd_start) { | 420 | if (initrd_start) { |
422 | unsigned long initrd_size = ((unsigned char *)initrd_end) - ((unsigned char *)initrd_start); | 421 | unsigned long initrd_size = ((unsigned char *)initrd_end) - |
422 | ((unsigned char *)initrd_start); | ||
423 | const int width = sizeof(long) * 2; | ||
424 | |||
423 | printk("Initial ramdisk at: 0x%p (%lu bytes)\n", | 425 | printk("Initial ramdisk at: 0x%p (%lu bytes)\n", |
424 | (void *)initrd_start, initrd_size); | 426 | (void *)initrd_start, initrd_size); |
425 | 427 | ||
426 | if (CPHYSADDR(initrd_end) > PFN_PHYS(max_low_pfn)) { | 428 | if (CPHYSADDR(initrd_end) > PFN_PHYS(max_low_pfn)) { |
427 | printk("initrd extends beyond end of memory " | 429 | printk("initrd extends beyond end of memory " |
428 | "(0x%0*Lx > 0x%0*Lx)\ndisabling initrd\n", | 430 | "(0x%0*Lx > 0x%0*Lx)\ndisabling initrd\n", |
429 | sizeof(long) * 2, | 431 | width, |
430 | (unsigned long long)CPHYSADDR(initrd_end), | 432 | (unsigned long long) CPHYSADDR(initrd_end), |
431 | sizeof(long) * 2, | 433 | width, |
432 | (unsigned long long)PFN_PHYS(max_low_pfn)); | 434 | (unsigned long long) PFN_PHYS(max_low_pfn)); |
433 | initrd_start = initrd_end = 0; | 435 | initrd_start = initrd_end = 0; |
434 | initrd_reserve_bootmem = 0; | 436 | initrd_reserve_bootmem = 0; |
435 | } | 437 | } |
diff --git a/arch/mips/kernel/smp.c b/arch/mips/kernel/smp.c index d42f358754ad..298f82fe8440 100644 --- a/arch/mips/kernel/smp.c +++ b/arch/mips/kernel/smp.c | |||
@@ -247,6 +247,9 @@ void __init smp_prepare_cpus(unsigned int max_cpus) | |||
247 | current_thread_info()->cpu = 0; | 247 | current_thread_info()->cpu = 0; |
248 | smp_tune_scheduling(); | 248 | smp_tune_scheduling(); |
249 | plat_prepare_cpus(max_cpus); | 249 | plat_prepare_cpus(max_cpus); |
250 | #ifndef CONFIG_HOTPLUG_CPU | ||
251 | cpu_present_map = cpu_possible_map; | ||
252 | #endif | ||
250 | } | 253 | } |
251 | 254 | ||
252 | /* preload SMP state for boot cpu */ | 255 | /* preload SMP state for boot cpu */ |
@@ -442,7 +445,7 @@ static int __init topology_init(void) | |||
442 | int cpu; | 445 | int cpu; |
443 | int ret; | 446 | int ret; |
444 | 447 | ||
445 | for_each_cpu(cpu) { | 448 | for_each_present_cpu(cpu) { |
446 | ret = register_cpu(&per_cpu(cpu_devices, cpu), cpu, NULL); | 449 | ret = register_cpu(&per_cpu(cpu_devices, cpu), cpu, NULL); |
447 | if (ret) | 450 | if (ret) |
448 | printk(KERN_WARNING "topology_init: register_cpu %d " | 451 | printk(KERN_WARNING "topology_init: register_cpu %d " |
diff --git a/arch/mips/kernel/syscall.c b/arch/mips/kernel/syscall.c index 8f4fdd94dbd0..5e8a18a8e2bd 100644 --- a/arch/mips/kernel/syscall.c +++ b/arch/mips/kernel/syscall.c | |||
@@ -276,8 +276,7 @@ void sys_set_thread_area(unsigned long addr) | |||
276 | 276 | ||
277 | asmlinkage int _sys_sysmips(int cmd, long arg1, int arg2, int arg3) | 277 | asmlinkage int _sys_sysmips(int cmd, long arg1, int arg2, int arg3) |
278 | { | 278 | { |
279 | int tmp, len; | 279 | int tmp; |
280 | char __user *name; | ||
281 | 280 | ||
282 | switch(cmd) { | 281 | switch(cmd) { |
283 | case MIPS_ATOMIC_SET: | 282 | case MIPS_ATOMIC_SET: |
diff --git a/arch/mips/kernel/traps.c b/arch/mips/kernel/traps.c index 35cb08da3820..a7564b08eb4d 100644 --- a/arch/mips/kernel/traps.c +++ b/arch/mips/kernel/traps.c | |||
@@ -819,15 +819,30 @@ asmlinkage void do_watch(struct pt_regs *regs) | |||
819 | 819 | ||
820 | asmlinkage void do_mcheck(struct pt_regs *regs) | 820 | asmlinkage void do_mcheck(struct pt_regs *regs) |
821 | { | 821 | { |
822 | const int field = 2 * sizeof(unsigned long); | ||
823 | int multi_match = regs->cp0_status & ST0_TS; | ||
824 | |||
822 | show_regs(regs); | 825 | show_regs(regs); |
823 | dump_tlb_all(); | 826 | |
827 | if (multi_match) { | ||
828 | printk("Index : %0x\n", read_c0_index()); | ||
829 | printk("Pagemask: %0x\n", read_c0_pagemask()); | ||
830 | printk("EntryHi : %0*lx\n", field, read_c0_entryhi()); | ||
831 | printk("EntryLo0: %0*lx\n", field, read_c0_entrylo0()); | ||
832 | printk("EntryLo1: %0*lx\n", field, read_c0_entrylo1()); | ||
833 | printk("\n"); | ||
834 | dump_tlb_all(); | ||
835 | } | ||
836 | |||
837 | show_code((unsigned int *) regs->cp0_epc); | ||
838 | |||
824 | /* | 839 | /* |
825 | * Some chips may have other causes of machine check (e.g. SB1 | 840 | * Some chips may have other causes of machine check (e.g. SB1 |
826 | * graduation timer) | 841 | * graduation timer) |
827 | */ | 842 | */ |
828 | panic("Caught Machine Check exception - %scaused by multiple " | 843 | panic("Caught Machine Check exception - %scaused by multiple " |
829 | "matching entries in the TLB.", | 844 | "matching entries in the TLB.", |
830 | (regs->cp0_status & ST0_TS) ? "" : "not "); | 845 | (multi_match) ? "" : "not "); |
831 | } | 846 | } |
832 | 847 | ||
833 | asmlinkage void do_mt(struct pt_regs *regs) | 848 | asmlinkage void do_mt(struct pt_regs *regs) |
diff --git a/arch/mips/math-emu/dp_fint.c b/arch/mips/math-emu/dp_fint.c index a1962eb460f8..39a71de16f47 100644 --- a/arch/mips/math-emu/dp_fint.c +++ b/arch/mips/math-emu/dp_fint.c | |||
@@ -29,7 +29,9 @@ | |||
29 | 29 | ||
30 | ieee754dp ieee754dp_fint(int x) | 30 | ieee754dp ieee754dp_fint(int x) |
31 | { | 31 | { |
32 | COMPXDP; | 32 | u64 xm; |
33 | int xe; | ||
34 | int xs; | ||
33 | 35 | ||
34 | CLEARCX; | 36 | CLEARCX; |
35 | 37 | ||
diff --git a/arch/mips/math-emu/dp_flong.c b/arch/mips/math-emu/dp_flong.c index eae90a866aa1..f08f223e488a 100644 --- a/arch/mips/math-emu/dp_flong.c +++ b/arch/mips/math-emu/dp_flong.c | |||
@@ -29,7 +29,9 @@ | |||
29 | 29 | ||
30 | ieee754dp ieee754dp_flong(s64 x) | 30 | ieee754dp ieee754dp_flong(s64 x) |
31 | { | 31 | { |
32 | COMPXDP; | 32 | u64 xm; |
33 | int xe; | ||
34 | int xs; | ||
33 | 35 | ||
34 | CLEARCX; | 36 | CLEARCX; |
35 | 37 | ||
diff --git a/arch/mips/math-emu/sp_fint.c b/arch/mips/math-emu/sp_fint.c index 7aac13afb09a..e88e125e01c2 100644 --- a/arch/mips/math-emu/sp_fint.c +++ b/arch/mips/math-emu/sp_fint.c | |||
@@ -29,7 +29,9 @@ | |||
29 | 29 | ||
30 | ieee754sp ieee754sp_fint(int x) | 30 | ieee754sp ieee754sp_fint(int x) |
31 | { | 31 | { |
32 | COMPXSP; | 32 | unsigned xm; |
33 | int xe; | ||
34 | int xs; | ||
33 | 35 | ||
34 | CLEARCX; | 36 | CLEARCX; |
35 | 37 | ||
diff --git a/arch/mips/math-emu/sp_flong.c b/arch/mips/math-emu/sp_flong.c index 3d6c1d11c178..26d6919a269a 100644 --- a/arch/mips/math-emu/sp_flong.c +++ b/arch/mips/math-emu/sp_flong.c | |||
@@ -29,7 +29,9 @@ | |||
29 | 29 | ||
30 | ieee754sp ieee754sp_flong(s64 x) | 30 | ieee754sp ieee754sp_flong(s64 x) |
31 | { | 31 | { |
32 | COMPXDP; /* <--- need 64-bit mantissa temp */ | 32 | u64 xm; /* <--- need 64-bit mantissa temp */ |
33 | int xe; | ||
34 | int xs; | ||
33 | 35 | ||
34 | CLEARCX; | 36 | CLEARCX; |
35 | 37 | ||
diff --git a/arch/mips/mm/c-r4k.c b/arch/mips/mm/c-r4k.c index 6b3541769602..4a43924cd4fc 100644 --- a/arch/mips/mm/c-r4k.c +++ b/arch/mips/mm/c-r4k.c | |||
@@ -1161,6 +1161,31 @@ static void __init setup_scache(void) | |||
1161 | c->options |= MIPS_CPU_SUBSET_CACHES; | 1161 | c->options |= MIPS_CPU_SUBSET_CACHES; |
1162 | } | 1162 | } |
1163 | 1163 | ||
1164 | void au1x00_fixup_config_od(void) | ||
1165 | { | ||
1166 | /* | ||
1167 | * c0_config.od (bit 19) was write only (and read as 0) | ||
1168 | * on the early revisions of Alchemy SOCs. It disables the bus | ||
1169 | * transaction overlapping and needs to be set to fix various errata. | ||
1170 | */ | ||
1171 | switch (read_c0_prid()) { | ||
1172 | case 0x00030100: /* Au1000 DA */ | ||
1173 | case 0x00030201: /* Au1000 HA */ | ||
1174 | case 0x00030202: /* Au1000 HB */ | ||
1175 | case 0x01030200: /* Au1500 AB */ | ||
1176 | /* | ||
1177 | * Au1100 errata actually keeps silence about this bit, so we set it | ||
1178 | * just in case for those revisions that require it to be set according | ||
1179 | * to arch/mips/au1000/common/cputable.c | ||
1180 | */ | ||
1181 | case 0x02030200: /* Au1100 AB */ | ||
1182 | case 0x02030201: /* Au1100 BA */ | ||
1183 | case 0x02030202: /* Au1100 BC */ | ||
1184 | set_c0_config(1 << 19); | ||
1185 | break; | ||
1186 | } | ||
1187 | } | ||
1188 | |||
1164 | static inline void coherency_setup(void) | 1189 | static inline void coherency_setup(void) |
1165 | { | 1190 | { |
1166 | change_c0_config(CONF_CM_CMASK, CONF_CM_DEFAULT); | 1191 | change_c0_config(CONF_CM_CMASK, CONF_CM_DEFAULT); |
@@ -1181,6 +1206,15 @@ static inline void coherency_setup(void) | |||
1181 | case CPU_R4400MC: | 1206 | case CPU_R4400MC: |
1182 | clear_c0_config(CONF_CU); | 1207 | clear_c0_config(CONF_CU); |
1183 | break; | 1208 | break; |
1209 | /* | ||
1210 | * We need to catch the ealry Alchemy SOCs with | ||
1211 | * the write-only co_config.od bit and set it back to one... | ||
1212 | */ | ||
1213 | case CPU_AU1000: /* rev. DA, HA, HB */ | ||
1214 | case CPU_AU1100: /* rev. AB, BA, BC ?? */ | ||
1215 | case CPU_AU1500: /* rev. AB */ | ||
1216 | au1x00_fixup_config_od(); | ||
1217 | break; | ||
1184 | } | 1218 | } |
1185 | } | 1219 | } |
1186 | 1220 | ||
diff --git a/arch/mips/mm/init.c b/arch/mips/mm/init.c index c22308b93ff0..33f6e1cdfd5b 100644 --- a/arch/mips/mm/init.c +++ b/arch/mips/mm/init.c | |||
@@ -227,7 +227,7 @@ void __init mem_init(void) | |||
227 | for (tmp = 0; tmp < max_low_pfn; tmp++) | 227 | for (tmp = 0; tmp < max_low_pfn; tmp++) |
228 | if (page_is_ram(tmp)) { | 228 | if (page_is_ram(tmp)) { |
229 | ram++; | 229 | ram++; |
230 | if (PageReserved(mem_map+tmp)) | 230 | if (PageReserved(pfn_to_page(tmp))) |
231 | reservedpages++; | 231 | reservedpages++; |
232 | } | 232 | } |
233 | 233 | ||
diff --git a/arch/mips/momentum/jaguar_atx/dbg_io.c b/arch/mips/momentum/jaguar_atx/dbg_io.c index 542eac82b63c..d7dea0a136aa 100644 --- a/arch/mips/momentum/jaguar_atx/dbg_io.c +++ b/arch/mips/momentum/jaguar_atx/dbg_io.c | |||
@@ -73,7 +73,7 @@ void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) | |||
73 | /* disable interrupts */ | 73 | /* disable interrupts */ |
74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); | 74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); |
75 | 75 | ||
76 | /* set up buad rate */ | 76 | /* set up baud rate */ |
77 | { | 77 | { |
78 | uint32 divisor; | 78 | uint32 divisor; |
79 | 79 | ||
diff --git a/arch/mips/momentum/ocelot_c/dbg_io.c b/arch/mips/momentum/ocelot_c/dbg_io.c index 8720bccfdea2..f0a6a38fcf4d 100644 --- a/arch/mips/momentum/ocelot_c/dbg_io.c +++ b/arch/mips/momentum/ocelot_c/dbg_io.c | |||
@@ -73,7 +73,7 @@ void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) | |||
73 | /* disable interrupts */ | 73 | /* disable interrupts */ |
74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); | 74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); |
75 | 75 | ||
76 | /* set up buad rate */ | 76 | /* set up baud rate */ |
77 | { | 77 | { |
78 | uint32 divisor; | 78 | uint32 divisor; |
79 | 79 | ||
diff --git a/arch/mips/momentum/ocelot_g/dbg_io.c b/arch/mips/momentum/ocelot_g/dbg_io.c index 8720bccfdea2..f0a6a38fcf4d 100644 --- a/arch/mips/momentum/ocelot_g/dbg_io.c +++ b/arch/mips/momentum/ocelot_g/dbg_io.c | |||
@@ -73,7 +73,7 @@ void debugInit(uint32 baud, uint8 data, uint8 parity, uint8 stop) | |||
73 | /* disable interrupts */ | 73 | /* disable interrupts */ |
74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); | 74 | UART16550_WRITE(OFS_INTR_ENABLE, 0); |
75 | 75 | ||
76 | /* set up buad rate */ | 76 | /* set up baud rate */ |
77 | { | 77 | { |
78 | uint32 divisor; | 78 | uint32 divisor; |
79 | 79 | ||
diff --git a/arch/mips/oprofile/common.c b/arch/mips/oprofile/common.c index 91b799d2cd88..c31e4cff64e0 100644 --- a/arch/mips/oprofile/common.c +++ b/arch/mips/oprofile/common.c | |||
@@ -14,8 +14,8 @@ | |||
14 | 14 | ||
15 | #include "op_impl.h" | 15 | #include "op_impl.h" |
16 | 16 | ||
17 | extern struct op_mips_model op_model_mipsxx __attribute__((weak)); | 17 | extern struct op_mips_model op_model_mipsxx_ops __attribute__((weak)); |
18 | extern struct op_mips_model op_model_rm9000 __attribute__((weak)); | 18 | extern struct op_mips_model op_model_rm9000_ops __attribute__((weak)); |
19 | 19 | ||
20 | static struct op_mips_model *model; | 20 | static struct op_mips_model *model; |
21 | 21 | ||
@@ -83,11 +83,11 @@ int __init oprofile_arch_init(struct oprofile_operations *ops) | |||
83 | case CPU_74K: | 83 | case CPU_74K: |
84 | case CPU_SB1: | 84 | case CPU_SB1: |
85 | case CPU_SB1A: | 85 | case CPU_SB1A: |
86 | lmodel = &op_model_mipsxx; | 86 | lmodel = &op_model_mipsxx_ops; |
87 | break; | 87 | break; |
88 | 88 | ||
89 | case CPU_RM9000: | 89 | case CPU_RM9000: |
90 | lmodel = &op_model_rm9000; | 90 | lmodel = &op_model_rm9000_ops; |
91 | break; | 91 | break; |
92 | }; | 92 | }; |
93 | 93 | ||
diff --git a/arch/mips/oprofile/op_model_mipsxx.c b/arch/mips/oprofile/op_model_mipsxx.c index e7ce92391303..f26a00e13204 100644 --- a/arch/mips/oprofile/op_model_mipsxx.c +++ b/arch/mips/oprofile/op_model_mipsxx.c | |||
@@ -23,7 +23,7 @@ | |||
23 | 23 | ||
24 | #define M_COUNTER_OVERFLOW (1UL << 31) | 24 | #define M_COUNTER_OVERFLOW (1UL << 31) |
25 | 25 | ||
26 | struct op_mips_model op_model_mipsxx; | 26 | struct op_mips_model op_model_mipsxx_ops; |
27 | 27 | ||
28 | static struct mipsxx_register_config { | 28 | static struct mipsxx_register_config { |
29 | unsigned int control[4]; | 29 | unsigned int control[4]; |
@@ -34,7 +34,7 @@ static struct mipsxx_register_config { | |||
34 | 34 | ||
35 | static void mipsxx_reg_setup(struct op_counter_config *ctr) | 35 | static void mipsxx_reg_setup(struct op_counter_config *ctr) |
36 | { | 36 | { |
37 | unsigned int counters = op_model_mipsxx.num_counters; | 37 | unsigned int counters = op_model_mipsxx_ops.num_counters; |
38 | int i; | 38 | int i; |
39 | 39 | ||
40 | /* Compute the performance counter control word. */ | 40 | /* Compute the performance counter control word. */ |
@@ -62,7 +62,7 @@ static void mipsxx_reg_setup(struct op_counter_config *ctr) | |||
62 | 62 | ||
63 | static void mipsxx_cpu_setup (void *args) | 63 | static void mipsxx_cpu_setup (void *args) |
64 | { | 64 | { |
65 | unsigned int counters = op_model_mipsxx.num_counters; | 65 | unsigned int counters = op_model_mipsxx_ops.num_counters; |
66 | 66 | ||
67 | switch (counters) { | 67 | switch (counters) { |
68 | case 4: | 68 | case 4: |
@@ -83,7 +83,7 @@ static void mipsxx_cpu_setup (void *args) | |||
83 | /* Start all counters on current CPU */ | 83 | /* Start all counters on current CPU */ |
84 | static void mipsxx_cpu_start(void *args) | 84 | static void mipsxx_cpu_start(void *args) |
85 | { | 85 | { |
86 | unsigned int counters = op_model_mipsxx.num_counters; | 86 | unsigned int counters = op_model_mipsxx_ops.num_counters; |
87 | 87 | ||
88 | switch (counters) { | 88 | switch (counters) { |
89 | case 4: | 89 | case 4: |
@@ -100,7 +100,7 @@ static void mipsxx_cpu_start(void *args) | |||
100 | /* Stop all counters on current CPU */ | 100 | /* Stop all counters on current CPU */ |
101 | static void mipsxx_cpu_stop(void *args) | 101 | static void mipsxx_cpu_stop(void *args) |
102 | { | 102 | { |
103 | unsigned int counters = op_model_mipsxx.num_counters; | 103 | unsigned int counters = op_model_mipsxx_ops.num_counters; |
104 | 104 | ||
105 | switch (counters) { | 105 | switch (counters) { |
106 | case 4: | 106 | case 4: |
@@ -116,7 +116,7 @@ static void mipsxx_cpu_stop(void *args) | |||
116 | 116 | ||
117 | static int mipsxx_perfcount_handler(struct pt_regs *regs) | 117 | static int mipsxx_perfcount_handler(struct pt_regs *regs) |
118 | { | 118 | { |
119 | unsigned int counters = op_model_mipsxx.num_counters; | 119 | unsigned int counters = op_model_mipsxx_ops.num_counters; |
120 | unsigned int control; | 120 | unsigned int control; |
121 | unsigned int counter; | 121 | unsigned int counter; |
122 | int handled = 0; | 122 | int handled = 0; |
@@ -187,37 +187,37 @@ static int __init mipsxx_init(void) | |||
187 | 187 | ||
188 | reset_counters(counters); | 188 | reset_counters(counters); |
189 | 189 | ||
190 | op_model_mipsxx.num_counters = counters; | 190 | op_model_mipsxx_ops.num_counters = counters; |
191 | switch (current_cpu_data.cputype) { | 191 | switch (current_cpu_data.cputype) { |
192 | case CPU_20KC: | 192 | case CPU_20KC: |
193 | op_model_mipsxx.cpu_type = "mips/20K"; | 193 | op_model_mipsxx_ops.cpu_type = "mips/20K"; |
194 | break; | 194 | break; |
195 | 195 | ||
196 | case CPU_24K: | 196 | case CPU_24K: |
197 | op_model_mipsxx.cpu_type = "mips/24K"; | 197 | op_model_mipsxx_ops.cpu_type = "mips/24K"; |
198 | break; | 198 | break; |
199 | 199 | ||
200 | case CPU_25KF: | 200 | case CPU_25KF: |
201 | op_model_mipsxx.cpu_type = "mips/25K"; | 201 | op_model_mipsxx_ops.cpu_type = "mips/25K"; |
202 | break; | 202 | break; |
203 | 203 | ||
204 | #ifndef CONFIG_SMP | 204 | #ifndef CONFIG_SMP |
205 | case CPU_34K: | 205 | case CPU_34K: |
206 | op_model_mipsxx.cpu_type = "mips/34K"; | 206 | op_model_mipsxx_ops.cpu_type = "mips/34K"; |
207 | break; | 207 | break; |
208 | 208 | ||
209 | case CPU_74K: | 209 | case CPU_74K: |
210 | op_model_mipsxx.cpu_type = "mips/74K"; | 210 | op_model_mipsxx_ops.cpu_type = "mips/74K"; |
211 | break; | 211 | break; |
212 | #endif | 212 | #endif |
213 | 213 | ||
214 | case CPU_5KC: | 214 | case CPU_5KC: |
215 | op_model_mipsxx.cpu_type = "mips/5K"; | 215 | op_model_mipsxx_ops.cpu_type = "mips/5K"; |
216 | break; | 216 | break; |
217 | 217 | ||
218 | case CPU_SB1: | 218 | case CPU_SB1: |
219 | case CPU_SB1A: | 219 | case CPU_SB1A: |
220 | op_model_mipsxx.cpu_type = "mips/sb1"; | 220 | op_model_mipsxx_ops.cpu_type = "mips/sb1"; |
221 | break; | 221 | break; |
222 | 222 | ||
223 | default: | 223 | default: |
@@ -233,12 +233,12 @@ static int __init mipsxx_init(void) | |||
233 | 233 | ||
234 | static void mipsxx_exit(void) | 234 | static void mipsxx_exit(void) |
235 | { | 235 | { |
236 | reset_counters(op_model_mipsxx.num_counters); | 236 | reset_counters(op_model_mipsxx_ops.num_counters); |
237 | 237 | ||
238 | perf_irq = null_perf_irq; | 238 | perf_irq = null_perf_irq; |
239 | } | 239 | } |
240 | 240 | ||
241 | struct op_mips_model op_model_mipsxx = { | 241 | struct op_mips_model op_model_mipsxx_ops = { |
242 | .reg_setup = mipsxx_reg_setup, | 242 | .reg_setup = mipsxx_reg_setup, |
243 | .cpu_setup = mipsxx_cpu_setup, | 243 | .cpu_setup = mipsxx_cpu_setup, |
244 | .init = mipsxx_init, | 244 | .init = mipsxx_init, |
diff --git a/arch/mips/oprofile/op_model_rm9000.c b/arch/mips/oprofile/op_model_rm9000.c index 9b75e41c78ef..b7063fefa65b 100644 --- a/arch/mips/oprofile/op_model_rm9000.c +++ b/arch/mips/oprofile/op_model_rm9000.c | |||
@@ -126,7 +126,7 @@ static void rm9000_exit(void) | |||
126 | free_irq(rm9000_perfcount_irq, NULL); | 126 | free_irq(rm9000_perfcount_irq, NULL); |
127 | } | 127 | } |
128 | 128 | ||
129 | struct op_mips_model op_model_rm9000 = { | 129 | struct op_mips_model op_model_rm9000_ops = { |
130 | .reg_setup = rm9000_reg_setup, | 130 | .reg_setup = rm9000_reg_setup, |
131 | .cpu_setup = rm9000_cpu_setup, | 131 | .cpu_setup = rm9000_cpu_setup, |
132 | .init = rm9000_init, | 132 | .init = rm9000_init, |
diff --git a/arch/mips/sgi-ip32/ip32-irq.c b/arch/mips/sgi-ip32/ip32-irq.c index de01c9815bdd..8ba08047d164 100644 --- a/arch/mips/sgi-ip32/ip32-irq.c +++ b/arch/mips/sgi-ip32/ip32-irq.c | |||
@@ -31,12 +31,12 @@ | |||
31 | /* issue a PIO read to make sure no PIO writes are pending */ | 31 | /* issue a PIO read to make sure no PIO writes are pending */ |
32 | static void inline flush_crime_bus(void) | 32 | static void inline flush_crime_bus(void) |
33 | { | 33 | { |
34 | volatile unsigned long junk = crime->control; | 34 | crime->control; |
35 | } | 35 | } |
36 | 36 | ||
37 | static void inline flush_mace_bus(void) | 37 | static void inline flush_mace_bus(void) |
38 | { | 38 | { |
39 | volatile unsigned long junk = mace->perif.ctrl.misc; | 39 | mace->perif.ctrl.misc; |
40 | } | 40 | } |
41 | 41 | ||
42 | #undef DEBUG_IRQ | 42 | #undef DEBUG_IRQ |
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig index 003b077c2324..45bcf098e762 100644 --- a/drivers/mmc/Kconfig +++ b/drivers/mmc/Kconfig | |||
@@ -84,7 +84,7 @@ config MMC_WBSD | |||
84 | 84 | ||
85 | config MMC_AU1X | 85 | config MMC_AU1X |
86 | tristate "Alchemy AU1XX0 MMC Card Interface support" | 86 | tristate "Alchemy AU1XX0 MMC Card Interface support" |
87 | depends on SOC_AU1X00 && MMC | 87 | depends on MMC && SOC_AU1200 |
88 | help | 88 | help |
89 | This selects the AMD Alchemy(R) Multimedia card interface. | 89 | This selects the AMD Alchemy(R) Multimedia card interface. |
90 | If you have a Alchemy platform with a MMC slot, say Y or M here. | 90 | If you have a Alchemy platform with a MMC slot, say Y or M here. |
diff --git a/include/asm-arm/arch-l7200/serial_l7200.h b/include/asm-arm/arch-l7200/serial_l7200.h index 238c595d97ea..b1008a9d23e5 100644 --- a/include/asm-arm/arch-l7200/serial_l7200.h +++ b/include/asm-arm/arch-l7200/serial_l7200.h | |||
@@ -28,7 +28,7 @@ | |||
28 | #define UARTDR 0x00 /* Tx/Rx data */ | 28 | #define UARTDR 0x00 /* Tx/Rx data */ |
29 | #define RXSTAT 0x04 /* Rx status */ | 29 | #define RXSTAT 0x04 /* Rx status */ |
30 | #define H_UBRLCR 0x08 /* mode register high */ | 30 | #define H_UBRLCR 0x08 /* mode register high */ |
31 | #define M_UBRLCR 0x0C /* mode reg mid (MSB of buad)*/ | 31 | #define M_UBRLCR 0x0C /* mode reg mid (MSB of baud)*/ |
32 | #define L_UBRLCR 0x10 /* mode reg low (LSB of baud)*/ | 32 | #define L_UBRLCR 0x10 /* mode reg low (LSB of baud)*/ |
33 | #define UARTCON 0x14 /* control register */ | 33 | #define UARTCON 0x14 /* control register */ |
34 | #define UARTFLG 0x18 /* flag register */ | 34 | #define UARTFLG 0x18 /* flag register */ |
diff --git a/include/asm-arm/arch-l7200/uncompress.h b/include/asm-arm/arch-l7200/uncompress.h index 9fcd40aee3e3..04be2a088639 100644 --- a/include/asm-arm/arch-l7200/uncompress.h +++ b/include/asm-arm/arch-l7200/uncompress.h | |||
@@ -6,7 +6,7 @@ | |||
6 | * Changelog: | 6 | * Changelog: |
7 | * 05-01-2000 SJH Created | 7 | * 05-01-2000 SJH Created |
8 | * 05-13-2000 SJH Filled in function bodies | 8 | * 05-13-2000 SJH Filled in function bodies |
9 | * 07-26-2000 SJH Removed hard coded buad rate | 9 | * 07-26-2000 SJH Removed hard coded baud rate |
10 | */ | 10 | */ |
11 | 11 | ||
12 | #include <asm/hardware.h> | 12 | #include <asm/hardware.h> |
diff --git a/include/asm-mips/addrspace.h b/include/asm-mips/addrspace.h index 42520cc84b0f..1386af1cb7d9 100644 --- a/include/asm-mips/addrspace.h +++ b/include/asm-mips/addrspace.h | |||
@@ -129,6 +129,7 @@ | |||
129 | #if defined (CONFIG_CPU_R4300) \ | 129 | #if defined (CONFIG_CPU_R4300) \ |
130 | || defined (CONFIG_CPU_R4X00) \ | 130 | || defined (CONFIG_CPU_R4X00) \ |
131 | || defined (CONFIG_CPU_R5000) \ | 131 | || defined (CONFIG_CPU_R5000) \ |
132 | || defined (CONFIG_CPU_RM7000) \ | ||
132 | || defined (CONFIG_CPU_NEVADA) \ | 133 | || defined (CONFIG_CPU_NEVADA) \ |
133 | || defined (CONFIG_CPU_TX49XX) \ | 134 | || defined (CONFIG_CPU_TX49XX) \ |
134 | || defined (CONFIG_CPU_MIPS64) | 135 | || defined (CONFIG_CPU_MIPS64) |
diff --git a/include/asm-mips/delay.h b/include/asm-mips/delay.h index 64dd45150f64..928f30f8c45c 100644 --- a/include/asm-mips/delay.h +++ b/include/asm-mips/delay.h | |||
@@ -19,20 +19,22 @@ static inline void __delay(unsigned long loops) | |||
19 | { | 19 | { |
20 | if (sizeof(long) == 4) | 20 | if (sizeof(long) == 4) |
21 | __asm__ __volatile__ ( | 21 | __asm__ __volatile__ ( |
22 | ".set\tnoreorder\n" | 22 | " .set noreorder \n" |
23 | "1:\tbnez\t%0,1b\n\t" | 23 | " .align 3 \n" |
24 | "subu\t%0,1\n\t" | 24 | "1: bnez %0, 1b \n" |
25 | ".set\treorder" | 25 | " subu %0, 1 \n" |
26 | " .set reorder \n" | ||
26 | : "=r" (loops) | 27 | : "=r" (loops) |
27 | : "0" (loops)); | 28 | : "0" (loops)); |
28 | else if (sizeof(long) == 8) | 29 | else if (sizeof(long) == 8) |
29 | __asm__ __volatile__ ( | 30 | __asm__ __volatile__ ( |
30 | ".set\tnoreorder\n" | 31 | " .set noreorder \n" |
31 | "1:\tbnez\t%0,1b\n\t" | 32 | " .align 3 \n" |
32 | "dsubu\t%0,1\n\t" | 33 | "1: bnez %0, 1b \n" |
33 | ".set\treorder" | 34 | " dsubu %0, 1 \n" |
34 | :"=r" (loops) | 35 | " .set reorder \n" |
35 | :"0" (loops)); | 36 | : "=r" (loops) |
37 | : "0" (loops)); | ||
36 | } | 38 | } |
37 | 39 | ||
38 | 40 | ||
diff --git a/include/asm-mips/page.h b/include/asm-mips/page.h index a1eab136ff6c..4035ec79ecd4 100644 --- a/include/asm-mips/page.h +++ b/include/asm-mips/page.h | |||
@@ -139,9 +139,11 @@ typedef struct { unsigned long pgprot; } pgprot_t; | |||
139 | 139 | ||
140 | #define pfn_to_kaddr(pfn) __va((pfn) << PAGE_SHIFT) | 140 | #define pfn_to_kaddr(pfn) __va((pfn) << PAGE_SHIFT) |
141 | 141 | ||
142 | #ifndef CONFIG_SPARSEMEM | ||
142 | #ifndef CONFIG_NEED_MULTIPLE_NODES | 143 | #ifndef CONFIG_NEED_MULTIPLE_NODES |
143 | #define pfn_valid(pfn) ((pfn) < max_mapnr) | 144 | #define pfn_valid(pfn) ((pfn) < max_mapnr) |
144 | #endif | 145 | #endif |
146 | #endif | ||
145 | 147 | ||
146 | #define virt_to_page(kaddr) pfn_to_page(__pa(kaddr) >> PAGE_SHIFT) | 148 | #define virt_to_page(kaddr) pfn_to_page(__pa(kaddr) >> PAGE_SHIFT) |
147 | #define virt_addr_valid(kaddr) pfn_valid(__pa(kaddr) >> PAGE_SHIFT) | 149 | #define virt_addr_valid(kaddr) pfn_valid(__pa(kaddr) >> PAGE_SHIFT) |
diff --git a/include/asm-mips/pgtable-32.h b/include/asm-mips/pgtable-32.h index 4d6bc45df594..087c20769256 100644 --- a/include/asm-mips/pgtable-32.h +++ b/include/asm-mips/pgtable-32.h | |||
@@ -177,48 +177,67 @@ pfn_pte(unsigned long pfn, pgprot_t prot) | |||
177 | ((swp_entry_t) { ((type) << 10) | ((offset) << 15) }) | 177 | ((swp_entry_t) { ((type) << 10) | ((offset) << 15) }) |
178 | 178 | ||
179 | /* | 179 | /* |
180 | * Bits 0, 1, 2, 9 and 10 are taken, split up the 27 bits of offset | 180 | * Bits 0, 4, 8, and 9 are taken, split up 28 bits of offset into this range: |
181 | * into this range: | ||
182 | */ | 181 | */ |
183 | #define PTE_FILE_MAX_BITS 27 | 182 | #define PTE_FILE_MAX_BITS 28 |
184 | 183 | ||
185 | #define pte_to_pgoff(_pte) \ | 184 | #define pte_to_pgoff(_pte) ((((_pte).pte >> 1 ) & 0x07) | \ |
186 | ((((_pte).pte >> 3) & 0x3f ) + (((_pte).pte >> 11) << 8 )) | 185 | (((_pte).pte >> 2 ) & 0x38) | \ |
186 | (((_pte).pte >> 10) << 6 )) | ||
187 | 187 | ||
188 | #define pgoff_to_pte(off) \ | 188 | #define pgoff_to_pte(off) ((pte_t) { (((off) & 0x07) << 1 ) | \ |
189 | ((pte_t) { (((off) & 0x3f) << 3) + (((off) >> 8) << 11) + _PAGE_FILE }) | 189 | (((off) & 0x38) << 2 ) | \ |
190 | (((off) >> 6 ) << 10) | \ | ||
191 | _PAGE_FILE }) | ||
190 | 192 | ||
191 | #else | 193 | #else |
192 | 194 | ||
193 | /* Swap entries must have VALID and GLOBAL bits cleared. */ | 195 | /* Swap entries must have VALID and GLOBAL bits cleared. */ |
196 | #if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_CPU_MIPS32) | ||
197 | #define __swp_type(x) (((x).val >> 2) & 0x1f) | ||
198 | #define __swp_offset(x) ((x).val >> 7) | ||
199 | #define __swp_entry(type,offset) \ | ||
200 | ((swp_entry_t) { ((type) << 2) | ((offset) << 7) }) | ||
201 | #else | ||
194 | #define __swp_type(x) (((x).val >> 8) & 0x1f) | 202 | #define __swp_type(x) (((x).val >> 8) & 0x1f) |
195 | #define __swp_offset(x) ((x).val >> 13) | 203 | #define __swp_offset(x) ((x).val >> 13) |
196 | #define __swp_entry(type,offset) \ | 204 | #define __swp_entry(type,offset) \ |
197 | ((swp_entry_t) { ((type) << 8) | ((offset) << 13) }) | 205 | ((swp_entry_t) { ((type) << 8) | ((offset) << 13) }) |
206 | #endif /* defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_CPU_MIPS32) */ | ||
198 | 207 | ||
208 | #if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_CPU_MIPS32) | ||
199 | /* | 209 | /* |
200 | * Bits 0, 1, 2, 7 and 8 are taken, split up the 27 bits of offset | 210 | * Bits 0 and 1 of pte_high are taken, use the rest for the page offset... |
201 | * into this range: | ||
202 | */ | 211 | */ |
203 | #define PTE_FILE_MAX_BITS 27 | 212 | #define PTE_FILE_MAX_BITS 30 |
204 | 213 | ||
205 | #if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_CPU_MIPS32_R1) | 214 | #define pte_to_pgoff(_pte) ((_pte).pte_high >> 2) |
206 | /* fixme */ | 215 | #define pgoff_to_pte(off) ((pte_t) { _PAGE_FILE, (off) << 2 }) |
207 | #define pte_to_pgoff(_pte) (((_pte).pte_high >> 6) + ((_pte).pte_high & 0x3f)) | ||
208 | #define pgoff_to_pte(off) \ | ||
209 | ((pte_t){(((off) & 0x3f) + ((off) << 6) + _PAGE_FILE)}) | ||
210 | 216 | ||
211 | #else | 217 | #else |
212 | #define pte_to_pgoff(_pte) \ | 218 | /* |
213 | ((((_pte).pte >> 3) & 0x1f ) + (((_pte).pte >> 9) << 6 )) | 219 | * Bits 0, 4, 6, and 7 are taken, split up 28 bits of offset into this range: |
220 | */ | ||
221 | #define PTE_FILE_MAX_BITS 28 | ||
222 | |||
223 | #define pte_to_pgoff(_pte) ((((_pte).pte >> 1) & 0x7) | \ | ||
224 | (((_pte).pte >> 2) & 0x8) | \ | ||
225 | (((_pte).pte >> 8) << 4)) | ||
214 | 226 | ||
215 | #define pgoff_to_pte(off) \ | 227 | #define pgoff_to_pte(off) ((pte_t) { (((off) & 0x7) << 1) | \ |
216 | ((pte_t) { (((off) & 0x1f) << 3) + (((off) >> 6) << 9) + _PAGE_FILE }) | 228 | (((off) & 0x8) << 2) | \ |
229 | (((off) >> 4) << 8) | \ | ||
230 | _PAGE_FILE }) | ||
217 | #endif | 231 | #endif |
218 | 232 | ||
219 | #endif | 233 | #endif |
220 | 234 | ||
235 | #if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_CPU_MIPS32) | ||
236 | #define __pte_to_swp_entry(pte) ((swp_entry_t) { (pte).pte_high }) | ||
237 | #define __swp_entry_to_pte(x) ((pte_t) { 0, (x).val }) | ||
238 | #else | ||
221 | #define __pte_to_swp_entry(pte) ((swp_entry_t) { pte_val(pte) }) | 239 | #define __pte_to_swp_entry(pte) ((swp_entry_t) { pte_val(pte) }) |
222 | #define __swp_entry_to_pte(x) ((pte_t) { (x).val }) | 240 | #define __swp_entry_to_pte(x) ((pte_t) { (x).val }) |
241 | #endif | ||
223 | 242 | ||
224 | #endif /* _ASM_PGTABLE_32_H */ | 243 | #endif /* _ASM_PGTABLE_32_H */ |
diff --git a/include/asm-mips/pgtable-64.h b/include/asm-mips/pgtable-64.h index 82166b254b27..2faf5c9ff127 100644 --- a/include/asm-mips/pgtable-64.h +++ b/include/asm-mips/pgtable-64.h | |||
@@ -224,15 +224,12 @@ static inline pte_t mk_swap_pte(unsigned long type, unsigned long offset) | |||
224 | #define __swp_entry_to_pte(x) ((pte_t) { (x).val }) | 224 | #define __swp_entry_to_pte(x) ((pte_t) { (x).val }) |
225 | 225 | ||
226 | /* | 226 | /* |
227 | * Bits 0, 1, 2, 7 and 8 are taken, split up the 32 bits of offset | 227 | * Bits 0, 4, 6, and 7 are taken. Let's leave bits 1, 2, 3, and 5 alone to |
228 | * into this range: | 228 | * make things easier, and only use the upper 56 bits for the page offset... |
229 | */ | 229 | */ |
230 | #define PTE_FILE_MAX_BITS 32 | 230 | #define PTE_FILE_MAX_BITS 56 |
231 | 231 | ||
232 | #define pte_to_pgoff(_pte) \ | 232 | #define pte_to_pgoff(_pte) ((_pte).pte >> 8) |
233 | ((((_pte).pte >> 3) & 0x1f ) + (((_pte).pte >> 9) << 6 )) | 233 | #define pgoff_to_pte(off) ((pte_t) { ((off) << 8) | _PAGE_FILE }) |
234 | |||
235 | #define pgoff_to_pte(off) \ | ||
236 | ((pte_t) { (((off) & 0x1f) << 3) + (((off) >> 6) << 9) + _PAGE_FILE }) | ||
237 | 234 | ||
238 | #endif /* _ASM_PGTABLE_64_H */ | 235 | #endif /* _ASM_PGTABLE_64_H */ |
diff --git a/include/asm-mips/pgtable.h b/include/asm-mips/pgtable.h index f80fe75c7800..d0af2a3b0152 100644 --- a/include/asm-mips/pgtable.h +++ b/include/asm-mips/pgtable.h | |||
@@ -353,8 +353,9 @@ static inline pgprot_t pgprot_noncached(pgprot_t _prot) | |||
353 | #if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_CPU_MIPS32_R1) | 353 | #if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_CPU_MIPS32_R1) |
354 | static inline pte_t pte_modify(pte_t pte, pgprot_t newprot) | 354 | static inline pte_t pte_modify(pte_t pte, pgprot_t newprot) |
355 | { | 355 | { |
356 | pte.pte_low &= _PAGE_CHG_MASK; | 356 | pte.pte_low &= _PAGE_CHG_MASK; |
357 | pte.pte_low |= pgprot_val(newprot); | 357 | pte.pte_high &= ~0x3f; |
358 | pte.pte_low |= pgprot_val(newprot); | ||
358 | pte.pte_high |= pgprot_val(newprot) & 0x3f; | 359 | pte.pte_high |= pgprot_val(newprot) & 0x3f; |
359 | return pte; | 360 | return pte; |
360 | } | 361 | } |
diff --git a/include/asm-mips/smp.h b/include/asm-mips/smp.h index 75c6fe7c2126..e14e4b69de21 100644 --- a/include/asm-mips/smp.h +++ b/include/asm-mips/smp.h | |||
@@ -48,7 +48,6 @@ extern struct call_data_struct *call_data; | |||
48 | #define SMP_CALL_FUNCTION 0x2 | 48 | #define SMP_CALL_FUNCTION 0x2 |
49 | 49 | ||
50 | extern cpumask_t phys_cpu_present_map; | 50 | extern cpumask_t phys_cpu_present_map; |
51 | extern cpumask_t cpu_online_map; | ||
52 | #define cpu_possible_map phys_cpu_present_map | 51 | #define cpu_possible_map phys_cpu_present_map |
53 | 52 | ||
54 | extern cpumask_t cpu_callout_map; | 53 | extern cpumask_t cpu_callout_map; |
@@ -86,9 +85,9 @@ extern void prom_init_secondary(void); | |||
86 | extern void plat_smp_setup(void); | 85 | extern void plat_smp_setup(void); |
87 | 86 | ||
88 | /* | 87 | /* |
89 | * Called after init_IRQ but before __cpu_up. | 88 | * Called in smp_prepare_cpus. |
90 | */ | 89 | */ |
91 | extern void prom_prepare_cpus(unsigned int max_cpus); | 90 | extern void plat_prepare_cpus(unsigned int max_cpus); |
92 | 91 | ||
93 | /* | 92 | /* |
94 | * Last chance for the board code to finish SMP initialization before | 93 | * Last chance for the board code to finish SMP initialization before |
diff --git a/include/asm-mips/sparsemem.h b/include/asm-mips/sparsemem.h new file mode 100644 index 000000000000..795ac6c23203 --- /dev/null +++ b/include/asm-mips/sparsemem.h | |||
@@ -0,0 +1,14 @@ | |||
1 | #ifndef _MIPS_SPARSEMEM_H | ||
2 | #define _MIPS_SPARSEMEM_H | ||
3 | #ifdef CONFIG_SPARSEMEM | ||
4 | |||
5 | /* | ||
6 | * SECTION_SIZE_BITS 2^N: how big each section will be | ||
7 | * MAX_PHYSMEM_BITS 2^N: how much memory we can have in that space | ||
8 | */ | ||
9 | #define SECTION_SIZE_BITS 28 | ||
10 | #define MAX_PHYSMEM_BITS 35 | ||
11 | |||
12 | #endif /* CONFIG_SPARSEMEM */ | ||
13 | #endif /* _MIPS_SPARSEMEM_H */ | ||
14 | |||