3 files changed, 58 insertions, 14 deletions

diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index af84984df775..50aa3b2a19b8 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -206,12 +206,20 @@ int kgdb_get_debug_char(void)
 }
 #endif
 
+#if ANOMALY_05000230 && defined(CONFIG_SERIAL_BFIN_PIO)
+# define UART_GET_ANOMALY_THRESHOLD(uart)    ((uart)->anomaly_threshold)
+# define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v))
+#else
+# define UART_GET_ANOMALY_THRESHOLD(uart)    0
+# define UART_SET_ANOMALY_THRESHOLD(uart, v)
+#endif
+
 #ifdef CONFIG_SERIAL_BFIN_PIO
 static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
 {
         struct tty_struct *tty = uart->port.info->tty;
         unsigned int status, ch, flg;
-        static int in_break = 0;
+        static struct timeval anomaly_start = { .tv_sec = 0 };
 #ifdef CONFIG_KGDB_UART
         struct pt_regs *regs = get_irq_regs();
 #endif
@@ -244,28 +252,56 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
 #endif
 
         if (ANOMALY_05000230) {
-                /* The BF533 family of processors have a nice misbehavior where
-                 * they continuously generate characters for a "single" break.
+                /* The BF533 (and BF561) family of processors have a nice anomaly
+                 * where they continuously generate characters for a "single" break.
                  * We have to basically ignore this flood until the "next" valid
-                 * character comes across.  All other Blackfin families operate
-                 * properly though.
+                 * character comes across.  Due to the nature of the flood, it is
+                 * not possible to reliably catch bytes that are sent too quickly
+                 * after this break.  So application code talking to the Blackfin
+                 * which sends a break signal must allow at least 1.5 character
+                 * times after the end of the break for things to stabilize.  This
+                 * timeout was picked as it must absolutely be larger than 1
+                 * character time +/- some percent.  So 1.5 sounds good.  All other
+                 * Blackfin families operate properly.  Woo.
                  * Note: While Anomaly 05000230 does not directly address this,
                  *       the changes that went in for it also fixed this issue.
+                 *       That anomaly was fixed in 0.5+ silicon.  I like bunnies.
                  */
-                if (in_break) {
-                        if (ch != 0) {
-                                in_break = 0;
-                                ch = UART_GET_CHAR(uart);
-                                if (bfin_revid() < 5)
-                                        return;
-                        } else
-                                return;
+                if (anomaly_start.tv_sec) {
+                        struct timeval curr;
+                        suseconds_t usecs;
+
+                        if ((~ch & (~ch + 1)) & 0xff)
+                                goto known_good_char;
+
+                        do_gettimeofday(&curr);
+                        if (curr.tv_sec - anomaly_start.tv_sec > 1)
+                                goto known_good_char;
+
+                        usecs = 0;
+                        if (curr.tv_sec != anomaly_start.tv_sec)
+                                usecs += USEC_PER_SEC;
+                        usecs += curr.tv_usec - anomaly_start.tv_usec;
+
+                        if (usecs > UART_GET_ANOMALY_THRESHOLD(uart))
+                                goto known_good_char;
+
+                        if (ch)
+                                anomaly_start.tv_sec = 0;
+                        else
+                                anomaly_start = curr;
+
+                        return;
+
+ known_good_char:
+                        anomaly_start.tv_sec = 0;
                 }
         }
 
         if (status & BI) {
                 if (ANOMALY_05000230)
-                        in_break = 1;
+                        if (bfin_revid() < 5)
+                                do_gettimeofday(&anomaly_start);
                 uart->port.icount.brk++;
                 if (uart_handle_break(&uart->port))
                         goto ignore_char;
@@ -778,6 +814,8 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
         quot = uart_get_divisor(port, baud);
         spin_lock_irqsave(&uart->port.lock, flags);
 
+        UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
+
         do {
                 lsr = UART_GET_LSR(uart);
         } while (!(lsr & TEMT));
diff --git a/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
index b619065ceeb0..a1b4f4eebd06 100644
--- a/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
+++ b/include/asm-blackfin/mach-bf533/bfin_serial_5xx.h
@@ -57,6 +57,9 @@ struct bfin_serial_port {
         struct work_struct      tx_dma_workqueue;
 #else
         struct work_struct      cts_workqueue;
+# if ANOMALY_05000230
+        unsigned int anomaly_threshold;
+# endif
 #endif
 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
         int                     cts_pin;
diff --git a/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h
index b619065ceeb0..a1b4f4eebd06 100644
--- a/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h
+++ b/include/asm-blackfin/mach-bf561/bfin_serial_5xx.h
@@ -57,6 +57,9 @@ struct bfin_serial_port {
         struct work_struct      tx_dma_workqueue;
 #else
         struct work_struct      cts_workqueue;
+# if ANOMALY_05000230
+        unsigned int anomaly_threshold;
+# endif
 #endif
 #ifdef CONFIG_SERIAL_BFIN_CTSRTS
         int                     cts_pin;