1 files changed, 66 insertions, 106 deletions

diff --git a/drivers/ide/pci/it8213.c b/drivers/ide/pci/it8213.c
index 6b46edfba811..63248b6909fa 100644
--- a/drivers/ide/pci/it8213.c
+++ b/drivers/ide/pci/it8213.c
@@ -1,3 +1,11 @@
+/*
+ * ITE 8213 IDE driver
+ *
+ * Copyright (C) 2006 Jack Lee
+ * Copyright (C) 2006 Alan Cox
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
+ */
+
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/module.h>
@@ -14,14 +22,14 @@
  *      @drive: IDE drive
  *
  *      Compute the available speeds for the devices on the interface. This
- *      is all modes to ATA100 clipped by drive cable setup.
+ *      is all modes to ATA133 clipped by drive cable setup.
  */
 
 static u8 it8213_ratemask (ide_drive_t *drive)
 {
         u8 mode = 4;
         if (!eighty_ninty_three(drive))
-                mode = min(mode, (u8)1);
+                mode = min_t(u8, mode, 1);
         return mode;
 }
 
@@ -62,55 +70,57 @@ static u8 it8213_dma_2_pio (u8 xfer_rate) {
         }
 }
 
-static spinlock_t tune_lock = SPIN_LOCK_UNLOCKED;
-
 /*
  *      it8213_tuneproc -       tune a drive
  *      @drive: drive to tune
- *      @mode_wanted: the target operating mode
- *
- *      Load the timing settings for this device mode into the
- *      controller. By the time we are called the mode has been
- *      modified as neccessary to handle the absence of seperate
- *      master/slave timers for MWDMA/PIO.
+ *      @pio: desired PIO mode
  *
- *      This code is only used in pass through mode.
+ *      Set the interface PIO mode.
  */
 
-static void it8213_tuneproc (ide_drive_t *drive,  u8 pio)
+static void it8213_tuneproc (ide_drive_t *drive, u8 pio)
 {
         ide_hwif_t *hwif        = HWIF(drive);
         struct pci_dev *dev     = hwif->pci_dev;
-        int is_slave            = (&hwif->drives[1] == drive);
+        int is_slave            = drive->dn & 1;
         int master_port         = 0x40;
         int slave_port          = 0x44;
         unsigned long flags;
         u16 master_data;
         u8 slave_data;
+        static DEFINE_SPINLOCK(tune_lock);
+        int control = 0;
 
-        u8 timings[][2] = { { 0, 0 },
-                            { 0, 0 },
-                            { 1, 0 },
-                            { 2, 1 },
-                            { 2, 3 }, };
+        static const u8 timings[][2]= {
+                                        { 0, 0 },
+                                        { 0, 0 },
+                                        { 1, 0 },
+                                        { 2, 1 },
+                                        { 2, 3 }, };
 
-        pio = ide_get_best_pio_mode(drive, pio, 5, NULL);
+        pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
 
         spin_lock_irqsave(&tune_lock, flags);
         pci_read_config_word(dev, master_port, &master_data);
+
+        if (pio > 1)
+                control |= 1;   /* Programmable timing on */
+        if (drive->media != ide_disk)
+                control |= 4;   /* ATAPI */
+        if (pio > 2)
+                control |= 2;   /* IORDY */
         if (is_slave) {
-                master_data = master_data | 0x4000;
+                master_data |=  0x4000;
+                master_data &= ~0x0070;
                 if (pio > 1)
-
-                        master_data = master_data | 0x0070;
+                        master_data = master_data | (control << 4);
                 pci_read_config_byte(dev, slave_port, &slave_data);
                 slave_data = slave_data & 0xf0;
-                slave_data = slave_data | (((timings[pio][0] << 2) | (timings[pio][1]) << 0));
+                slave_data = slave_data | (timings[pio][0] << 2) | timings[pio][1];
         } else {
-                master_data = master_data & 0xccf8;
+                master_data &= ~0x3307;
                 if (pio > 1)
-
-                        master_data = master_data | 0x0007;
+                        master_data = master_data | control;
                 master_data = master_data | (timings[pio][0] << 12) | (timings[pio][1] << 8);
         }
         pci_write_config_word(dev, master_port, master_data);
@@ -119,7 +129,6 @@ static void it8213_tuneproc (ide_drive_t *drive,  u8 pio)
         spin_unlock_irqrestore(&tune_lock, flags);
 }
 
-
 /**
  *      it8213_tune_chipset     -       set controller timings
  *      @drive: Drive to set up
@@ -130,7 +139,7 @@ static void it8213_tuneproc (ide_drive_t *drive,  u8 pio)
  *      make the thing work.
  */
 
-static int it8213_tune_chipset (ide_drive_t *drive, byte xferspeed)
+static int it8213_tune_chipset (ide_drive_t *drive, u8 xferspeed)
 {
 
         ide_hwif_t *hwif        = HWIF(drive);
@@ -154,15 +163,15 @@ static int it8213_tune_chipset (ide_drive_t *drive, byte xferspeed)
         switch(speed) {
                 case XFER_UDMA_6:
                 case XFER_UDMA_4:
-                case XFER_UDMA_2:u_speed = 2 << (drive->dn * 4); break;
+                case XFER_UDMA_2:       u_speed = 2 << (drive->dn * 4); break;
                 case XFER_UDMA_5:
                 case XFER_UDMA_3:
-                case XFER_UDMA_1:u_speed = 1 << (drive->dn * 4); break;
-                case XFER_UDMA_0:u_speed = 0 << (drive->dn * 4); break;
+                case XFER_UDMA_1:       u_speed = 1 << (drive->dn * 4); break;
+                case XFER_UDMA_0:       u_speed = 0 << (drive->dn * 4); break;
                         break;
                 case XFER_MW_DMA_2:
                 case XFER_MW_DMA_1:
-                case XFER_MW_DMA_0:
+                case XFER_SW_DMA_2:
                         break;
                 case XFER_PIO_4:
                 case XFER_PIO_3:
@@ -174,8 +183,7 @@ static int it8213_tune_chipset (ide_drive_t *drive, byte xferspeed)
                         return -1;
         }
 
-                if (speed >= XFER_UDMA_0)
-                {
+        if (speed >= XFER_UDMA_0) {
                 if (!(reg48 & u_flag))
                         pci_write_config_byte(dev, 0x48, reg48 | u_flag);
                 if (speed >= XFER_UDMA_5) {
@@ -186,14 +194,12 @@ static int it8213_tune_chipset (ide_drive_t *drive, byte xferspeed)
 
                 if ((reg4a & a_speed) != u_speed)
                         pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
-                if (speed > XFER_UDMA_2)
-                {
+                if (speed > XFER_UDMA_2) {
                         if (!(reg54 & v_flag))
                                 pci_write_config_byte(dev, 0x54, reg54 | v_flag);
                 } else
                         pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
-                } else /*if(speed >= XFER_UDMA_0)*/
-                {
+        } else {
                 if (reg48 & u_flag)
                         pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
                 if (reg4a & a_speed)
@@ -202,11 +208,10 @@ static int it8213_tune_chipset (ide_drive_t *drive, byte xferspeed)
                         pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
                 if (reg55 & w_flag)
                         pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
-                }
+        }
         it8213_tuneproc(drive, it8213_dma_2_pio(speed));
         return ide_config_drive_speed(drive, speed);
-        }
-
+}
 
 /*
  *      config_chipset_for_dma  -       configure for DMA
@@ -217,48 +222,17 @@ static int it8213_tune_chipset (ide_drive_t *drive, byte xferspeed)
 
 static int config_chipset_for_dma (ide_drive_t *drive)
 {
-          u8 speed      = ide_dma_speed(drive, it8213_ratemask(drive));
+        u8 speed = ide_dma_speed(drive, it8213_ratemask(drive));
+
         if (!speed)
-        {
-                u8 tspeed = ide_get_best_pio_mode(drive, 255, 5, NULL);
-                speed = it8213_dma_2_pio(XFER_PIO_0 + tspeed);
-        }
-//      config_it8213_chipset_for_pio(drive, !speed);
+                return 0;
+
         it8213_tune_chipset(drive, speed);
+
         return ide_dma_enable(drive);
 }
 
 /**
- *      config_it8213_chipset_for_pio   -       set drive timings
- *      @drive: drive to tune
- *      @speed we want
- *
- *      Compute the best pio mode we can for a given device. We must
- *      pick a speed that does not cause problems with the other device
- *      on the cable.
- */
-/*
-static void config_it8213_chipset_for_pio (ide_drive_t *drive, byte set_speed)
-{
-        ide_hwif_t *hwif        = HWIF(drive);
-//      u8 unit = drive->select.b.unit;
-        ide_hwif_t *hwif = drive->hwif;
-        ide_drive_t *pair = &hwif->drives[1-unit];
-        u8 speed = 0, set_pio   = ide_get_best_pio_mode(drive, 255, 5, NULL);
-        u8 pair_pio;
-
-        if(pair != NULL) {
-                pair_pio = ide_get_best_pio_mode(pair, 255, 5, NULL);
-                if(pair_pio < set_pio)
-                        set_pio = pair_pio;
-        }
-        it8213_tuneproc(drive, set_pio);
-        speed = XFER_PIO_0 + set_pio;
-        if (set_speed)
-                (void) ide_config_drive_speed(drive, speed);
-}
-*/
-/**
  *      it8213_configure_drive_for_dma  -       set up for DMA transfers
  *      @drive: drive we are going to set up
  *
@@ -270,26 +244,19 @@ static void config_it8213_chipset_for_pio (ide_drive_t *drive, byte set_speed)
 
 static int it8213_config_drive_for_dma (ide_drive_t *drive)
 {
-//      ide_hwif_t *hwif        = drive->hwif;
-//      struct hd_driveid *id = drive->id;
-        ide_hwif_t *hwif        = HWIF(drive);
+        ide_hwif_t *hwif = drive->hwif;
+
         if (ide_use_dma(drive)) {
                 if (config_chipset_for_dma(drive))
                         return hwif->ide_dma_on(drive);
         }
-//      config_it8213_chipset_for_pio(drive, 1);
-        hwif->tuneproc(drive, 255);
-        return hwif->ide_dma_off_quietly(drive);
-}
 
+        hwif->speedproc(drive, XFER_PIO_0
+                        + ide_get_best_pio_mode(drive, 255, 4, NULL));
 
-static unsigned int __devinit init_chipset_it8213(struct pci_dev *dev, const char *name)
-{
-        printk(KERN_INFO "it8213: controller in IDE mode.\n");
-        return 0;
+        return hwif->ide_dma_off_quietly(drive);
 }
 
-
 /**
  *      init_hwif_it8213        -       set up hwif structs
  *      @hwif: interface to set up
@@ -302,9 +269,6 @@ static unsigned int __devinit init_chipset_it8213(struct pci_dev *dev, const cha
 static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
 {
         u8 reg42h = 0, ata66 = 0;
-        u8 mask = 0x02;
-
-        hwif->atapi_dma = 1;
 
         hwif->speedproc = &it8213_tune_chipset;
         hwif->tuneproc  = &it8213_tuneproc;
@@ -315,19 +279,19 @@ static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
         hwif->drives[1].autotune = 1;
 
         if (!hwif->dma_base)
-                goto fallback;
+                return;
+
         hwif->atapi_dma = 1;
         hwif->ultra_mask = 0x7f;
-        hwif->mwdma_mask = 0x07;
-        hwif->swdma_mask = 0x07;
+        hwif->mwdma_mask = 0x06;
+        hwif->swdma_mask = 0x04;
 
         pci_read_config_byte(hwif->pci_dev, 0x42, &reg42h);
-        ata66 = (reg42h & mask) ? 0 : 1;
+        ata66 = (reg42h & 0x02) ? 0 : 1;
 
         hwif->ide_dma_check = &it8213_config_drive_for_dma;
         if (!(hwif->udma_four))
                 hwif->udma_four = ata66;
-//              hwif->udma_four = 0;
 
         /*
          *      The BIOS often doesn't set up DMA on this controller
@@ -338,20 +302,15 @@ static void __devinit init_hwif_it8213(ide_hwif_t *hwif)
 
         hwif->drives[0].autodma = hwif->autodma;
         hwif->drives[1].autodma = hwif->autodma;
-        return;
-fallback:
-        hwif->autodma = 0;
-        return;
 }
 
 
 #define DECLARE_ITE_DEV(name_str)                       \
         {                                               \
                 .name           = name_str,             \
-                .init_chipset   = init_chipset_it8213,  \
                 .init_hwif      = init_hwif_it8213,     \
                 .channels       = 1,                    \
-                .autodma                = AUTODMA,              \
+                .autodma        = AUTODMA,              \
                 .enablebits     = {{0x41,0x80,0x80}}, \
                 .bootable       = ON_BOARD,             \
         }
@@ -379,7 +338,7 @@ static int __devinit it8213_init_one(struct pci_dev *dev, const struct pci_devic
 
 
 static struct pci_device_id it8213_pci_tbl[] = {
-        { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8213,  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+        { PCI_VENDOR_ID_ITE, 0x8213, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
         { 0, },
 };
 
@@ -393,10 +352,11 @@ static struct pci_driver driver = {
 
 static int __init it8213_ide_init(void)
 {
-        return ide_pci_register_driver(&driver); }
+        return ide_pci_register_driver(&driver);
+}
 
 module_init(it8213_ide_init);
 
-MODULE_AUTHOR("Jack and Alan Cox");             /* Update this */
+MODULE_AUTHOR("Jack Lee, Alan Cox");
 MODULE_DESCRIPTION("PCI driver module for the ITE 8213");
 MODULE_LICENSE("GPL");