aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--Documentation/spi/pxa2xx16
-rw-r--r--drivers/spi/pxa2xx_spi.c733
-rw-r--r--include/asm-arm/arch-pxa/pxa2xx_spi.h5
3 files changed, 449 insertions, 305 deletions
diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
index a1e0ee20f595..f9717fe9bd85 100644
--- a/Documentation/spi/pxa2xx
+++ b/Documentation/spi/pxa2xx
@@ -102,7 +102,7 @@ struct pxa2xx_spi_chip {
102 u8 tx_threshold; 102 u8 tx_threshold;
103 u8 rx_threshold; 103 u8 rx_threshold;
104 u8 dma_burst_size; 104 u8 dma_burst_size;
105 u32 timeout_microsecs; 105 u32 timeout;
106 u8 enable_loopback; 106 u8 enable_loopback;
107 void (*cs_control)(u32 command); 107 void (*cs_control)(u32 command);
108}; 108};
@@ -121,7 +121,7 @@ the PXA2xx "Developer Manual" sections on the DMA controller and SSP Controllers
121to determine the correct value. An SSP configured for byte-wide transfers would 121to determine the correct value. An SSP configured for byte-wide transfers would
122use a value of 8. 122use a value of 8.
123 123
124The "pxa2xx_spi_chip.timeout_microsecs" fields is used to efficiently handle 124The "pxa2xx_spi_chip.timeout" fields is used to efficiently handle
125trailing bytes in the SSP receiver fifo. The correct value for this field is 125trailing bytes in the SSP receiver fifo. The correct value for this field is
126dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific 126dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific
127slave device. Please note that the PXA2xx SSP 1 does not support trailing byte 127slave device. Please note that the PXA2xx SSP 1 does not support trailing byte
@@ -162,18 +162,18 @@ static void cs8405a_cs_control(u32 command)
162} 162}
163 163
164static struct pxa2xx_spi_chip cs8415a_chip_info = { 164static struct pxa2xx_spi_chip cs8415a_chip_info = {
165 .tx_threshold = 12, /* SSP hardward FIFO threshold */ 165 .tx_threshold = 8, /* SSP hardward FIFO threshold */
166 .rx_threshold = 4, /* SSP hardward FIFO threshold */ 166 .rx_threshold = 8, /* SSP hardward FIFO threshold */
167 .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */ 167 .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
168 .timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */ 168 .timeout = 235, /* See Intel documentation */
169 .cs_control = cs8415a_cs_control, /* Use external chip select */ 169 .cs_control = cs8415a_cs_control, /* Use external chip select */
170}; 170};
171 171
172static struct pxa2xx_spi_chip cs8405a_chip_info = { 172static struct pxa2xx_spi_chip cs8405a_chip_info = {
173 .tx_threshold = 12, /* SSP hardward FIFO threshold */ 173 .tx_threshold = 8, /* SSP hardward FIFO threshold */
174 .rx_threshold = 4, /* SSP hardward FIFO threshold */ 174 .rx_threshold = 8, /* SSP hardward FIFO threshold */
175 .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */ 175 .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
176 .timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */ 176 .timeout = 235, /* See Intel documentation */
177 .cs_control = cs8405a_cs_control, /* Use external chip select */ 177 .cs_control = cs8405a_cs_control, /* Use external chip select */
178}; 178};
179 179
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
index 494d9b856488..6ed3f1da9296 100644
--- a/drivers/spi/pxa2xx_spi.c
+++ b/drivers/spi/pxa2xx_spi.c
@@ -49,6 +49,14 @@ MODULE_LICENSE("GPL");
49#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK) 49#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
50#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0) 50#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0)
51 51
52/* for testing SSCR1 changes that require SSP restart, basically
53 * everything except the service and interrupt enables */
54#define SSCR1_CHANGE_MASK (SSCR1_TTELP | SSCR1_TTE | SSCR1_EBCEI | SSCR1_SCFR \
55 | SSCR1_ECRA | SSCR1_ECRB | SSCR1_SCLKDIR \
56 | SSCR1_RWOT | SSCR1_TRAIL | SSCR1_PINTE \
57 | SSCR1_STRF | SSCR1_EFWR |SSCR1_RFT \
58 | SSCR1_TFT | SSCR1_SPH | SSCR1_SPO | SSCR1_LBM)
59
52#define DEFINE_SSP_REG(reg, off) \ 60#define DEFINE_SSP_REG(reg, off) \
53static inline u32 read_##reg(void *p) { return __raw_readl(p + (off)); } \ 61static inline u32 read_##reg(void *p) { return __raw_readl(p + (off)); } \
54static inline void write_##reg(u32 v, void *p) { __raw_writel(v, p + (off)); } 62static inline void write_##reg(u32 v, void *p) { __raw_writel(v, p + (off)); }
@@ -123,8 +131,8 @@ struct driver_data {
123 u8 n_bytes; 131 u8 n_bytes;
124 u32 dma_width; 132 u32 dma_width;
125 int cs_change; 133 int cs_change;
126 void (*write)(struct driver_data *drv_data); 134 int (*write)(struct driver_data *drv_data);
127 void (*read)(struct driver_data *drv_data); 135 int (*read)(struct driver_data *drv_data);
128 irqreturn_t (*transfer_handler)(struct driver_data *drv_data); 136 irqreturn_t (*transfer_handler)(struct driver_data *drv_data);
129 void (*cs_control)(u32 command); 137 void (*cs_control)(u32 command);
130}; 138};
@@ -132,7 +140,6 @@ struct driver_data {
132struct chip_data { 140struct chip_data {
133 u32 cr0; 141 u32 cr0;
134 u32 cr1; 142 u32 cr1;
135 u32 to;
136 u32 psp; 143 u32 psp;
137 u32 timeout; 144 u32 timeout;
138 u8 n_bytes; 145 u8 n_bytes;
@@ -143,8 +150,8 @@ struct chip_data {
143 u8 enable_dma; 150 u8 enable_dma;
144 u8 bits_per_word; 151 u8 bits_per_word;
145 u32 speed_hz; 152 u32 speed_hz;
146 void (*write)(struct driver_data *drv_data); 153 int (*write)(struct driver_data *drv_data);
147 void (*read)(struct driver_data *drv_data); 154 int (*read)(struct driver_data *drv_data);
148 void (*cs_control)(u32 command); 155 void (*cs_control)(u32 command);
149}; 156};
150 157
@@ -166,114 +173,118 @@ static int flush(struct driver_data *drv_data)
166 return limit; 173 return limit;
167} 174}
168 175
169static void restore_state(struct driver_data *drv_data)
170{
171 void *reg = drv_data->ioaddr;
172
173 /* Clear status and disable clock */
174 write_SSSR(drv_data->clear_sr, reg);
175 write_SSCR0(drv_data->cur_chip->cr0 & ~SSCR0_SSE, reg);
176
177 /* Load the registers */
178 write_SSCR1(drv_data->cur_chip->cr1, reg);
179 write_SSCR0(drv_data->cur_chip->cr0, reg);
180 if (drv_data->ssp_type != PXA25x_SSP) {
181 write_SSTO(0, reg);
182 write_SSPSP(drv_data->cur_chip->psp, reg);
183 }
184}
185
186static void null_cs_control(u32 command) 176static void null_cs_control(u32 command)
187{ 177{
188} 178}
189 179
190static void null_writer(struct driver_data *drv_data) 180static int null_writer(struct driver_data *drv_data)
191{ 181{
192 void *reg = drv_data->ioaddr; 182 void *reg = drv_data->ioaddr;
193 u8 n_bytes = drv_data->n_bytes; 183 u8 n_bytes = drv_data->n_bytes;
194 184
195 while ((read_SSSR(reg) & SSSR_TNF) 185 if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
196 && (drv_data->tx < drv_data->tx_end)) { 186 || (drv_data->tx == drv_data->tx_end))
197 write_SSDR(0, reg); 187 return 0;
198 drv_data->tx += n_bytes; 188
199 } 189 write_SSDR(0, reg);
190 drv_data->tx += n_bytes;
191
192 return 1;
200} 193}
201 194
202static void null_reader(struct driver_data *drv_data) 195static int null_reader(struct driver_data *drv_data)
203{ 196{
204 void *reg = drv_data->ioaddr; 197 void *reg = drv_data->ioaddr;
205 u8 n_bytes = drv_data->n_bytes; 198 u8 n_bytes = drv_data->n_bytes;
206 199
207 while ((read_SSSR(reg) & SSSR_RNE) 200 while ((read_SSSR(reg) & SSSR_RNE)
208 && (drv_data->rx < drv_data->rx_end)) { 201 && (drv_data->rx < drv_data->rx_end)) {
209 read_SSDR(reg); 202 read_SSDR(reg);
210 drv_data->rx += n_bytes; 203 drv_data->rx += n_bytes;
211 } 204 }
205
206 return drv_data->rx == drv_data->rx_end;
212} 207}
213 208
214static void u8_writer(struct driver_data *drv_data) 209static int u8_writer(struct driver_data *drv_data)
215{ 210{
216 void *reg = drv_data->ioaddr; 211 void *reg = drv_data->ioaddr;
217 212
218 while ((read_SSSR(reg) & SSSR_TNF) 213 if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
219 && (drv_data->tx < drv_data->tx_end)) { 214 || (drv_data->tx == drv_data->tx_end))
220 write_SSDR(*(u8 *)(drv_data->tx), reg); 215 return 0;
221 ++drv_data->tx; 216
222 } 217 write_SSDR(*(u8 *)(drv_data->tx), reg);
218 ++drv_data->tx;
219
220 return 1;
223} 221}
224 222
225static void u8_reader(struct driver_data *drv_data) 223static int u8_reader(struct driver_data *drv_data)
226{ 224{
227 void *reg = drv_data->ioaddr; 225 void *reg = drv_data->ioaddr;
228 226
229 while ((read_SSSR(reg) & SSSR_RNE) 227 while ((read_SSSR(reg) & SSSR_RNE)
230 && (drv_data->rx < drv_data->rx_end)) { 228 && (drv_data->rx < drv_data->rx_end)) {
231 *(u8 *)(drv_data->rx) = read_SSDR(reg); 229 *(u8 *)(drv_data->rx) = read_SSDR(reg);
232 ++drv_data->rx; 230 ++drv_data->rx;
233 } 231 }
232
233 return drv_data->rx == drv_data->rx_end;
234} 234}
235 235
236static void u16_writer(struct driver_data *drv_data) 236static int u16_writer(struct driver_data *drv_data)
237{ 237{
238 void *reg = drv_data->ioaddr; 238 void *reg = drv_data->ioaddr;
239 239
240 while ((read_SSSR(reg) & SSSR_TNF) 240 if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
241 && (drv_data->tx < drv_data->tx_end)) { 241 || (drv_data->tx == drv_data->tx_end))
242 write_SSDR(*(u16 *)(drv_data->tx), reg); 242 return 0;
243 drv_data->tx += 2; 243
244 } 244 write_SSDR(*(u16 *)(drv_data->tx), reg);
245 drv_data->tx += 2;
246
247 return 1;
245} 248}
246 249
247static void u16_reader(struct driver_data *drv_data) 250static int u16_reader(struct driver_data *drv_data)
248{ 251{
249 void *reg = drv_data->ioaddr; 252 void *reg = drv_data->ioaddr;
250 253
251 while ((read_SSSR(reg) & SSSR_RNE) 254 while ((read_SSSR(reg) & SSSR_RNE)
252 && (drv_data->rx < drv_data->rx_end)) { 255 && (drv_data->rx < drv_data->rx_end)) {
253 *(u16 *)(drv_data->rx) = read_SSDR(reg); 256 *(u16 *)(drv_data->rx) = read_SSDR(reg);
254 drv_data->rx += 2; 257 drv_data->rx += 2;
255 } 258 }
259
260 return drv_data->rx == drv_data->rx_end;
256} 261}
257static void u32_writer(struct driver_data *drv_data) 262
263static int u32_writer(struct driver_data *drv_data)
258{ 264{
259 void *reg = drv_data->ioaddr; 265 void *reg = drv_data->ioaddr;
260 266
261 while ((read_SSSR(reg) & SSSR_TNF) 267 if (((read_SSSR(reg) & 0x00000f00) == 0x00000f00)
262 && (drv_data->tx < drv_data->tx_end)) { 268 || (drv_data->tx == drv_data->tx_end))
263 write_SSDR(*(u32 *)(drv_data->tx), reg); 269 return 0;
264 drv_data->tx += 4; 270
265 } 271 write_SSDR(*(u32 *)(drv_data->tx), reg);
272 drv_data->tx += 4;
273
274 return 1;
266} 275}
267 276
268static void u32_reader(struct driver_data *drv_data) 277static int u32_reader(struct driver_data *drv_data)
269{ 278{
270 void *reg = drv_data->ioaddr; 279 void *reg = drv_data->ioaddr;
271 280
272 while ((read_SSSR(reg) & SSSR_RNE) 281 while ((read_SSSR(reg) & SSSR_RNE)
273 && (drv_data->rx < drv_data->rx_end)) { 282 && (drv_data->rx < drv_data->rx_end)) {
274 *(u32 *)(drv_data->rx) = read_SSDR(reg); 283 *(u32 *)(drv_data->rx) = read_SSDR(reg);
275 drv_data->rx += 4; 284 drv_data->rx += 4;
276 } 285 }
286
287 return drv_data->rx == drv_data->rx_end;
277} 288}
278 289
279static void *next_transfer(struct driver_data *drv_data) 290static void *next_transfer(struct driver_data *drv_data)
@@ -409,166 +420,134 @@ static int wait_dma_channel_stop(int channel)
409 return limit; 420 return limit;
410} 421}
411 422
412static void dma_handler(int channel, void *data) 423void dma_error_stop(struct driver_data *drv_data, const char *msg)
413{ 424{
414 struct driver_data *drv_data = data;
415 struct spi_message *msg = drv_data->cur_msg;
416 void *reg = drv_data->ioaddr; 425 void *reg = drv_data->ioaddr;
417 u32 irq_status = DCSR(channel) & DMA_INT_MASK;
418 u32 trailing_sssr = 0;
419 426
420 if (irq_status & DCSR_BUSERR) { 427 /* Stop and reset */
428 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
429 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
430 write_SSSR(drv_data->clear_sr, reg);
431 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
432 if (drv_data->ssp_type != PXA25x_SSP)
433 write_SSTO(0, reg);
434 flush(drv_data);
435 write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
421 436
422 /* Disable interrupts, clear status and reset DMA */ 437 unmap_dma_buffers(drv_data);
423 write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
424 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
425 if (drv_data->ssp_type != PXA25x_SSP)
426 write_SSTO(0, reg);
427 write_SSSR(drv_data->clear_sr, reg);
428 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
429 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
430 438
431 if (flush(drv_data) == 0) 439 dev_err(&drv_data->pdev->dev, "%s\n", msg);
432 dev_err(&drv_data->pdev->dev,
433 "dma_handler: flush fail\n");
434 440
435 unmap_dma_buffers(drv_data); 441 drv_data->cur_msg->state = ERROR_STATE;
442 tasklet_schedule(&drv_data->pump_transfers);
443}
444
445static void dma_transfer_complete(struct driver_data *drv_data)
446{
447 void *reg = drv_data->ioaddr;
448 struct spi_message *msg = drv_data->cur_msg;
449
450 /* Clear and disable interrupts on SSP and DMA channels*/
451 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
452 write_SSSR(drv_data->clear_sr, reg);
453 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
454 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
455
456 if (wait_dma_channel_stop(drv_data->rx_channel) == 0)
457 dev_err(&drv_data->pdev->dev,
458 "dma_handler: dma rx channel stop failed\n");
459
460 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
461 dev_err(&drv_data->pdev->dev,
462 "dma_transfer: ssp rx stall failed\n");
463
464 unmap_dma_buffers(drv_data);
465
466 /* update the buffer pointer for the amount completed in dma */
467 drv_data->rx += drv_data->len -
468 (DCMD(drv_data->rx_channel) & DCMD_LENGTH);
469
470 /* read trailing data from fifo, it does not matter how many
471 * bytes are in the fifo just read until buffer is full
472 * or fifo is empty, which ever occurs first */
473 drv_data->read(drv_data);
474
475 /* return count of what was actually read */
476 msg->actual_length += drv_data->len -
477 (drv_data->rx_end - drv_data->rx);
478
479 /* Release chip select if requested, transfer delays are
480 * handled in pump_transfers */
481 if (drv_data->cs_change)
482 drv_data->cs_control(PXA2XX_CS_DEASSERT);
483
484 /* Move to next transfer */
485 msg->state = next_transfer(drv_data);
486
487 /* Schedule transfer tasklet */
488 tasklet_schedule(&drv_data->pump_transfers);
489}
490
491static void dma_handler(int channel, void *data)
492{
493 struct driver_data *drv_data = data;
494 u32 irq_status = DCSR(channel) & DMA_INT_MASK;
495
496 if (irq_status & DCSR_BUSERR) {
436 497
437 if (channel == drv_data->tx_channel) 498 if (channel == drv_data->tx_channel)
438 dev_err(&drv_data->pdev->dev, 499 dma_error_stop(drv_data,
439 "dma_handler: bad bus address on " 500 "dma_handler: "
440 "tx channel %d, source %x target = %x\n", 501 "bad bus address on tx channel");
441 channel, DSADR(channel), DTADR(channel));
442 else 502 else
443 dev_err(&drv_data->pdev->dev, 503 dma_error_stop(drv_data,
444 "dma_handler: bad bus address on " 504 "dma_handler: "
445 "rx channel %d, source %x target = %x\n", 505 "bad bus address on rx channel");
446 channel, DSADR(channel), DTADR(channel)); 506 return;
447
448 msg->state = ERROR_STATE;
449 tasklet_schedule(&drv_data->pump_transfers);
450 } 507 }
451 508
452 /* PXA255x_SSP has no timeout interrupt, wait for tailing bytes */ 509 /* PXA255x_SSP has no timeout interrupt, wait for tailing bytes */
453 if ((drv_data->ssp_type == PXA25x_SSP) 510 if ((channel == drv_data->tx_channel)
454 && (channel == drv_data->tx_channel) 511 && (irq_status & DCSR_ENDINTR)
455 && (irq_status & DCSR_ENDINTR)) { 512 && (drv_data->ssp_type == PXA25x_SSP)) {
456 513
457 /* Wait for rx to stall */ 514 /* Wait for rx to stall */
458 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0) 515 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
459 dev_err(&drv_data->pdev->dev, 516 dev_err(&drv_data->pdev->dev,
460 "dma_handler: ssp rx stall failed\n"); 517 "dma_handler: ssp rx stall failed\n");
461 518
462 /* Clear and disable interrupts on SSP and DMA channels*/ 519 /* finish this transfer, start the next */
463 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg); 520 dma_transfer_complete(drv_data);
464 write_SSSR(drv_data->clear_sr, reg);
465 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
466 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
467 if (wait_dma_channel_stop(drv_data->rx_channel) == 0)
468 dev_err(&drv_data->pdev->dev,
469 "dma_handler: dma rx channel stop failed\n");
470
471 unmap_dma_buffers(drv_data);
472
473 /* Read trailing bytes */
474 /* Calculate number of trailing bytes, read them */
475 trailing_sssr = read_SSSR(reg);
476 if ((trailing_sssr & 0xf008) != 0xf000) {
477 drv_data->rx = drv_data->rx_end -
478 (((trailing_sssr >> 12) & 0x0f) + 1);
479 drv_data->read(drv_data);
480 }
481 msg->actual_length += drv_data->len;
482
483 /* Release chip select if requested, transfer delays are
484 * handled in pump_transfers */
485 if (drv_data->cs_change)
486 drv_data->cs_control(PXA2XX_CS_DEASSERT);
487
488 /* Move to next transfer */
489 msg->state = next_transfer(drv_data);
490
491 /* Schedule transfer tasklet */
492 tasklet_schedule(&drv_data->pump_transfers);
493 } 521 }
494} 522}
495 523
496static irqreturn_t dma_transfer(struct driver_data *drv_data) 524static irqreturn_t dma_transfer(struct driver_data *drv_data)
497{ 525{
498 u32 irq_status; 526 u32 irq_status;
499 u32 trailing_sssr = 0;
500 struct spi_message *msg = drv_data->cur_msg;
501 void *reg = drv_data->ioaddr; 527 void *reg = drv_data->ioaddr;
502 528
503 irq_status = read_SSSR(reg) & drv_data->mask_sr; 529 irq_status = read_SSSR(reg) & drv_data->mask_sr;
504 if (irq_status & SSSR_ROR) { 530 if (irq_status & SSSR_ROR) {
505 /* Clear and disable interrupts on SSP and DMA channels*/ 531 dma_error_stop(drv_data, "dma_transfer: fifo overrun");
506 write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
507 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
508 if (drv_data->ssp_type != PXA25x_SSP)
509 write_SSTO(0, reg);
510 write_SSSR(drv_data->clear_sr, reg);
511 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
512 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
513 unmap_dma_buffers(drv_data);
514
515 if (flush(drv_data) == 0)
516 dev_err(&drv_data->pdev->dev,
517 "dma_transfer: flush fail\n");
518
519 dev_warn(&drv_data->pdev->dev, "dma_transfer: fifo overun\n");
520
521 drv_data->cur_msg->state = ERROR_STATE;
522 tasklet_schedule(&drv_data->pump_transfers);
523
524 return IRQ_HANDLED; 532 return IRQ_HANDLED;
525 } 533 }
526 534
527 /* Check for false positive timeout */ 535 /* Check for false positive timeout */
528 if ((irq_status & SSSR_TINT) && DCSR(drv_data->tx_channel) & DCSR_RUN) { 536 if ((irq_status & SSSR_TINT)
537 && (DCSR(drv_data->tx_channel) & DCSR_RUN)) {
529 write_SSSR(SSSR_TINT, reg); 538 write_SSSR(SSSR_TINT, reg);
530 return IRQ_HANDLED; 539 return IRQ_HANDLED;
531 } 540 }
532 541
533 if (irq_status & SSSR_TINT || drv_data->rx == drv_data->rx_end) { 542 if (irq_status & SSSR_TINT || drv_data->rx == drv_data->rx_end) {
534 543
535 /* Clear and disable interrupts on SSP and DMA channels*/ 544 /* Clear and disable timeout interrupt, do the rest in
536 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg); 545 * dma_transfer_complete */
537 if (drv_data->ssp_type != PXA25x_SSP) 546 if (drv_data->ssp_type != PXA25x_SSP)
538 write_SSTO(0, reg); 547 write_SSTO(0, reg);
539 write_SSSR(drv_data->clear_sr, reg);
540 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
541 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
542 548
543 if (wait_dma_channel_stop(drv_data->rx_channel) == 0) 549 /* finish this transfer, start the next */
544 dev_err(&drv_data->pdev->dev, 550 dma_transfer_complete(drv_data);
545 "dma_transfer: dma rx channel stop failed\n");
546
547 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
548 dev_err(&drv_data->pdev->dev,
549 "dma_transfer: ssp rx stall failed\n");
550
551 unmap_dma_buffers(drv_data);
552
553 /* Calculate number of trailing bytes, read them */
554 trailing_sssr = read_SSSR(reg);
555 if ((trailing_sssr & 0xf008) != 0xf000) {
556 drv_data->rx = drv_data->rx_end -
557 (((trailing_sssr >> 12) & 0x0f) + 1);
558 drv_data->read(drv_data);
559 }
560 msg->actual_length += drv_data->len;
561
562 /* Release chip select if requested, transfer delays are
563 * handled in pump_transfers */
564 if (drv_data->cs_change)
565 drv_data->cs_control(PXA2XX_CS_DEASSERT);
566
567 /* Move to next transfer */
568 msg->state = next_transfer(drv_data);
569
570 /* Schedule transfer tasklet */
571 tasklet_schedule(&drv_data->pump_transfers);
572 551
573 return IRQ_HANDLED; 552 return IRQ_HANDLED;
574 } 553 }
@@ -577,89 +556,103 @@ static irqreturn_t dma_transfer(struct driver_data *drv_data)
577 return IRQ_NONE; 556 return IRQ_NONE;
578} 557}
579 558
580static irqreturn_t interrupt_transfer(struct driver_data *drv_data) 559static void int_error_stop(struct driver_data *drv_data, const char* msg)
581{ 560{
582 struct spi_message *msg = drv_data->cur_msg;
583 void *reg = drv_data->ioaddr; 561 void *reg = drv_data->ioaddr;
584 unsigned long limit = loops_per_jiffy << 1;
585 u32 irq_status;
586 u32 irq_mask = (read_SSCR1(reg) & SSCR1_TIE) ?
587 drv_data->mask_sr : drv_data->mask_sr & ~SSSR_TFS;
588
589 while ((irq_status = read_SSSR(reg) & irq_mask)) {
590
591 if (irq_status & SSSR_ROR) {
592 562
593 /* Clear and disable interrupts */ 563 /* Stop and reset SSP */
594 write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg); 564 write_SSSR(drv_data->clear_sr, reg);
595 write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg); 565 write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
596 if (drv_data->ssp_type != PXA25x_SSP) 566 if (drv_data->ssp_type != PXA25x_SSP)
597 write_SSTO(0, reg); 567 write_SSTO(0, reg);
598 write_SSSR(drv_data->clear_sr, reg); 568 flush(drv_data);
569 write_SSCR0(read_SSCR0(reg) & ~SSCR0_SSE, reg);
599 570
600 if (flush(drv_data) == 0) 571 dev_err(&drv_data->pdev->dev, "%s\n", msg);
601 dev_err(&drv_data->pdev->dev,
602 "interrupt_transfer: flush fail\n");
603 572
604 /* Stop the SSP */ 573 drv_data->cur_msg->state = ERROR_STATE;
574 tasklet_schedule(&drv_data->pump_transfers);
575}
605 576
606 dev_warn(&drv_data->pdev->dev, 577static void int_transfer_complete(struct driver_data *drv_data)
607 "interrupt_transfer: fifo overun\n"); 578{
579 void *reg = drv_data->ioaddr;
608 580
609 msg->state = ERROR_STATE; 581 /* Stop SSP */
610 tasklet_schedule(&drv_data->pump_transfers); 582 write_SSSR(drv_data->clear_sr, reg);
583 write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
584 if (drv_data->ssp_type != PXA25x_SSP)
585 write_SSTO(0, reg);
611 586
612 return IRQ_HANDLED; 587 /* Update total byte transfered return count actual bytes read */
613 } 588 drv_data->cur_msg->actual_length += drv_data->len -
589 (drv_data->rx_end - drv_data->rx);
614 590
615 /* Look for false positive timeout */ 591 /* Release chip select if requested, transfer delays are
616 if ((irq_status & SSSR_TINT) 592 * handled in pump_transfers */
617 && (drv_data->rx < drv_data->rx_end)) 593 if (drv_data->cs_change)
618 write_SSSR(SSSR_TINT, reg); 594 drv_data->cs_control(PXA2XX_CS_DEASSERT);
619 595
620 /* Pump data */ 596 /* Move to next transfer */
621 drv_data->read(drv_data); 597 drv_data->cur_msg->state = next_transfer(drv_data);
622 drv_data->write(drv_data);
623 598
624 if (drv_data->tx == drv_data->tx_end) { 599 /* Schedule transfer tasklet */
625 /* Disable tx interrupt */ 600 tasklet_schedule(&drv_data->pump_transfers);
626 write_SSCR1(read_SSCR1(reg) & ~SSCR1_TIE, reg); 601}
627 irq_mask = drv_data->mask_sr & ~SSSR_TFS;
628 602
629 /* PXA25x_SSP has no timeout, read trailing bytes */ 603static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
630 if (drv_data->ssp_type == PXA25x_SSP) { 604{
631 while ((read_SSSR(reg) & SSSR_BSY) && limit--) 605 void *reg = drv_data->ioaddr;
632 drv_data->read(drv_data);
633 606
634 if (limit == 0) 607 u32 irq_mask = (read_SSCR1(reg) & SSCR1_TIE) ?
635 dev_err(&drv_data->pdev->dev, 608 drv_data->mask_sr : drv_data->mask_sr & ~SSSR_TFS;
636 "interrupt_transfer: "
637 "trailing byte read failed\n");
638 }
639 }
640 609
641 if ((irq_status & SSSR_TINT) 610 u32 irq_status = read_SSSR(reg) & irq_mask;
642 || (drv_data->rx == drv_data->rx_end)) {
643 611
644 /* Clear timeout */ 612 if (irq_status & SSSR_ROR) {
645 write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg); 613 int_error_stop(drv_data, "interrupt_transfer: fifo overrun");
646 if (drv_data->ssp_type != PXA25x_SSP) 614 return IRQ_HANDLED;
647 write_SSTO(0, reg); 615 }
648 write_SSSR(drv_data->clear_sr, reg);
649 616
650 /* Update total byte transfered */ 617 if (irq_status & SSSR_TINT) {
651 msg->actual_length += drv_data->len; 618 write_SSSR(SSSR_TINT, reg);
619 if (drv_data->read(drv_data)) {
620 int_transfer_complete(drv_data);
621 return IRQ_HANDLED;
622 }
623 }
652 624
653 /* Release chip select if requested, transfer delays are 625 /* Drain rx fifo, Fill tx fifo and prevent overruns */
654 * handled in pump_transfers */ 626 do {
655 if (drv_data->cs_change) 627 if (drv_data->read(drv_data)) {
656 drv_data->cs_control(PXA2XX_CS_DEASSERT); 628 int_transfer_complete(drv_data);
629 return IRQ_HANDLED;
630 }
631 } while (drv_data->write(drv_data));
657 632
658 /* Move to next transfer */ 633 if (drv_data->read(drv_data)) {
659 msg->state = next_transfer(drv_data); 634 int_transfer_complete(drv_data);
635 return IRQ_HANDLED;
636 }
660 637
661 /* Schedule transfer tasklet */ 638 if (drv_data->tx == drv_data->tx_end) {
662 tasklet_schedule(&drv_data->pump_transfers); 639 write_SSCR1(read_SSCR1(reg) & ~SSCR1_TIE, reg);
640 /* PXA25x_SSP has no timeout, read trailing bytes */
641 if (drv_data->ssp_type == PXA25x_SSP) {
642 if (!wait_ssp_rx_stall(reg))
643 {
644 int_error_stop(drv_data, "interrupt_transfer: "
645 "rx stall failed");
646 return IRQ_HANDLED;
647 }
648 if (!drv_data->read(drv_data))
649 {
650 int_error_stop(drv_data,
651 "interrupt_transfer: "
652 "trailing byte read failed");
653 return IRQ_HANDLED;
654 }
655 int_transfer_complete(drv_data);
663 } 656 }
664 } 657 }
665 658
@@ -681,7 +674,7 @@ static irqreturn_t ssp_int(int irq, void *dev_id)
681 write_SSSR(drv_data->clear_sr, reg); 674 write_SSSR(drv_data->clear_sr, reg);
682 675
683 dev_err(&drv_data->pdev->dev, "bad message state " 676 dev_err(&drv_data->pdev->dev, "bad message state "
684 "in interrupt handler"); 677 "in interrupt handler\n");
685 678
686 /* Never fail */ 679 /* Never fail */
687 return IRQ_HANDLED; 680 return IRQ_HANDLED;
@@ -690,6 +683,102 @@ static irqreturn_t ssp_int(int irq, void *dev_id)
690 return drv_data->transfer_handler(drv_data); 683 return drv_data->transfer_handler(drv_data);
691} 684}
692 685
686int set_dma_burst_and_threshold(struct chip_data *chip, struct spi_device *spi,
687 u8 bits_per_word, u32 *burst_code,
688 u32 *threshold)
689{
690 struct pxa2xx_spi_chip *chip_info =
691 (struct pxa2xx_spi_chip *)spi->controller_data;
692 int bytes_per_word;
693 int burst_bytes;
694 int thresh_words;
695 int req_burst_size;
696 int retval = 0;
697
698 /* Set the threshold (in registers) to equal the same amount of data
699 * as represented by burst size (in bytes). The computation below
700 * is (burst_size rounded up to nearest 8 byte, word or long word)
701 * divided by (bytes/register); the tx threshold is the inverse of
702 * the rx, so that there will always be enough data in the rx fifo
703 * to satisfy a burst, and there will always be enough space in the
704 * tx fifo to accept a burst (a tx burst will overwrite the fifo if
705 * there is not enough space), there must always remain enough empty
706 * space in the rx fifo for any data loaded to the tx fifo.
707 * Whenever burst_size (in bytes) equals bits/word, the fifo threshold
708 * will be 8, or half the fifo;
709 * The threshold can only be set to 2, 4 or 8, but not 16, because
710 * to burst 16 to the tx fifo, the fifo would have to be empty;
711 * however, the minimum fifo trigger level is 1, and the tx will
712 * request service when the fifo is at this level, with only 15 spaces.
713 */
714
715 /* find bytes/word */
716 if (bits_per_word <= 8)
717 bytes_per_word = 1;
718 else if (bits_per_word <= 16)
719 bytes_per_word = 2;
720 else
721 bytes_per_word = 4;
722
723 /* use struct pxa2xx_spi_chip->dma_burst_size if available */
724 if (chip_info)
725 req_burst_size = chip_info->dma_burst_size;
726 else {
727 switch (chip->dma_burst_size) {
728 default:
729 /* if the default burst size is not set,
730 * do it now */
731 chip->dma_burst_size = DCMD_BURST8;
732 case DCMD_BURST8:
733 req_burst_size = 8;
734 break;
735 case DCMD_BURST16:
736 req_burst_size = 16;
737 break;
738 case DCMD_BURST32:
739 req_burst_size = 32;
740 break;
741 }
742 }
743 if (req_burst_size <= 8) {
744 *burst_code = DCMD_BURST8;
745 burst_bytes = 8;
746 } else if (req_burst_size <= 16) {
747 if (bytes_per_word == 1) {
748 /* don't burst more than 1/2 the fifo */
749 *burst_code = DCMD_BURST8;
750 burst_bytes = 8;
751 retval = 1;
752 } else {
753 *burst_code = DCMD_BURST16;
754 burst_bytes = 16;
755 }
756 } else {
757 if (bytes_per_word == 1) {
758 /* don't burst more than 1/2 the fifo */
759 *burst_code = DCMD_BURST8;
760 burst_bytes = 8;
761 retval = 1;
762 } else if (bytes_per_word == 2) {
763 /* don't burst more than 1/2 the fifo */
764 *burst_code = DCMD_BURST16;
765 burst_bytes = 16;
766 retval = 1;
767 } else {
768 *burst_code = DCMD_BURST32;
769 burst_bytes = 32;
770 }
771 }
772
773 thresh_words = burst_bytes / bytes_per_word;
774
775 /* thresh_words will be between 2 and 8 */
776 *threshold = (SSCR1_RxTresh(thresh_words) & SSCR1_RFT)
777 | (SSCR1_TxTresh(16-thresh_words) & SSCR1_TFT);
778
779 return retval;
780}
781
693static void pump_transfers(unsigned long data) 782static void pump_transfers(unsigned long data)
694{ 783{
695 struct driver_data *drv_data = (struct driver_data *)data; 784 struct driver_data *drv_data = (struct driver_data *)data;
@@ -702,6 +791,9 @@ static void pump_transfers(unsigned long data)
702 u8 bits = 0; 791 u8 bits = 0;
703 u32 speed = 0; 792 u32 speed = 0;
704 u32 cr0; 793 u32 cr0;
794 u32 cr1;
795 u32 dma_thresh = drv_data->cur_chip->dma_threshold;
796 u32 dma_burst = drv_data->cur_chip->dma_burst_size;
705 797
706 /* Get current state information */ 798 /* Get current state information */
707 message = drv_data->cur_msg; 799 message = drv_data->cur_msg;
@@ -731,6 +823,16 @@ static void pump_transfers(unsigned long data)
731 udelay(previous->delay_usecs); 823 udelay(previous->delay_usecs);
732 } 824 }
733 825
826 /* Check transfer length */
827 if (transfer->len > 8191)
828 {
829 dev_warn(&drv_data->pdev->dev, "pump_transfers: transfer "
830 "length greater than 8191\n");
831 message->status = -EINVAL;
832 giveback(drv_data);
833 return;
834 }
835
734 /* Setup the transfer state based on the type of transfer */ 836 /* Setup the transfer state based on the type of transfer */
735 if (flush(drv_data) == 0) { 837 if (flush(drv_data) == 0) {
736 dev_err(&drv_data->pdev->dev, "pump_transfers: flush failed\n"); 838 dev_err(&drv_data->pdev->dev, "pump_transfers: flush failed\n");
@@ -747,17 +849,15 @@ static void pump_transfers(unsigned long data)
747 drv_data->rx_end = drv_data->rx + transfer->len; 849 drv_data->rx_end = drv_data->rx + transfer->len;
748 drv_data->rx_dma = transfer->rx_dma; 850 drv_data->rx_dma = transfer->rx_dma;
749 drv_data->tx_dma = transfer->tx_dma; 851 drv_data->tx_dma = transfer->tx_dma;
750 drv_data->len = transfer->len; 852 drv_data->len = transfer->len & DCMD_LENGTH;
751 drv_data->write = drv_data->tx ? chip->write : null_writer; 853 drv_data->write = drv_data->tx ? chip->write : null_writer;
752 drv_data->read = drv_data->rx ? chip->read : null_reader; 854 drv_data->read = drv_data->rx ? chip->read : null_reader;
753 drv_data->cs_change = transfer->cs_change; 855 drv_data->cs_change = transfer->cs_change;
754 856
755 /* Change speed and bit per word on a per transfer */ 857 /* Change speed and bit per word on a per transfer */
858 cr0 = chip->cr0;
756 if (transfer->speed_hz || transfer->bits_per_word) { 859 if (transfer->speed_hz || transfer->bits_per_word) {
757 860
758 /* Disable clock */
759 write_SSCR0(chip->cr0 & ~SSCR0_SSE, reg);
760 cr0 = chip->cr0;
761 bits = chip->bits_per_word; 861 bits = chip->bits_per_word;
762 speed = chip->speed_hz; 862 speed = chip->speed_hz;
763 863
@@ -796,15 +896,24 @@ static void pump_transfers(unsigned long data)
796 drv_data->write = drv_data->write != null_writer ? 896 drv_data->write = drv_data->write != null_writer ?
797 u32_writer : null_writer; 897 u32_writer : null_writer;
798 } 898 }
899 /* if bits/word is changed in dma mode, then must check the
900 * thresholds and burst also */
901 if (chip->enable_dma) {
902 if (set_dma_burst_and_threshold(chip, message->spi,
903 bits, &dma_burst,
904 &dma_thresh))
905 if (printk_ratelimit())
906 dev_warn(&message->spi->dev,
907 "pump_transfer: "
908 "DMA burst size reduced to "
909 "match bits_per_word\n");
910 }
799 911
800 cr0 = clk_div 912 cr0 = clk_div
801 | SSCR0_Motorola 913 | SSCR0_Motorola
802 | SSCR0_DataSize(bits > 16 ? bits - 16 : bits) 914 | SSCR0_DataSize(bits > 16 ? bits - 16 : bits)
803 | SSCR0_SSE 915 | SSCR0_SSE
804 | (bits > 16 ? SSCR0_EDSS : 0); 916 | (bits > 16 ? SSCR0_EDSS : 0);
805
806 /* Start it back up */
807 write_SSCR0(cr0, reg);
808 } 917 }
809 918
810 message->state = RUNNING_STATE; 919 message->state = RUNNING_STATE;
@@ -823,13 +932,13 @@ static void pump_transfers(unsigned long data)
823 /* No target address increment */ 932 /* No target address increment */
824 DCMD(drv_data->rx_channel) = DCMD_FLOWSRC 933 DCMD(drv_data->rx_channel) = DCMD_FLOWSRC
825 | drv_data->dma_width 934 | drv_data->dma_width
826 | chip->dma_burst_size 935 | dma_burst
827 | drv_data->len; 936 | drv_data->len;
828 else 937 else
829 DCMD(drv_data->rx_channel) = DCMD_INCTRGADDR 938 DCMD(drv_data->rx_channel) = DCMD_INCTRGADDR
830 | DCMD_FLOWSRC 939 | DCMD_FLOWSRC
831 | drv_data->dma_width 940 | drv_data->dma_width
832 | chip->dma_burst_size 941 | dma_burst
833 | drv_data->len; 942 | drv_data->len;
834 943
835 /* Setup tx DMA Channel */ 944 /* Setup tx DMA Channel */
@@ -840,13 +949,13 @@ static void pump_transfers(unsigned long data)
840 /* No source address increment */ 949 /* No source address increment */
841 DCMD(drv_data->tx_channel) = DCMD_FLOWTRG 950 DCMD(drv_data->tx_channel) = DCMD_FLOWTRG
842 | drv_data->dma_width 951 | drv_data->dma_width
843 | chip->dma_burst_size 952 | dma_burst
844 | drv_data->len; 953 | drv_data->len;
845 else 954 else
846 DCMD(drv_data->tx_channel) = DCMD_INCSRCADDR 955 DCMD(drv_data->tx_channel) = DCMD_INCSRCADDR
847 | DCMD_FLOWTRG 956 | DCMD_FLOWTRG
848 | drv_data->dma_width 957 | drv_data->dma_width
849 | chip->dma_burst_size 958 | dma_burst
850 | drv_data->len; 959 | drv_data->len;
851 960
852 /* Enable dma end irqs on SSP to detect end of transfer */ 961 /* Enable dma end irqs on SSP to detect end of transfer */
@@ -856,16 +965,11 @@ static void pump_transfers(unsigned long data)
856 /* Fix me, need to handle cs polarity */ 965 /* Fix me, need to handle cs polarity */
857 drv_data->cs_control(PXA2XX_CS_ASSERT); 966 drv_data->cs_control(PXA2XX_CS_ASSERT);
858 967
859 /* Go baby, go */ 968 /* Clear status and start DMA engine */
969 cr1 = chip->cr1 | dma_thresh | drv_data->dma_cr1;
860 write_SSSR(drv_data->clear_sr, reg); 970 write_SSSR(drv_data->clear_sr, reg);
861 DCSR(drv_data->rx_channel) |= DCSR_RUN; 971 DCSR(drv_data->rx_channel) |= DCSR_RUN;
862 DCSR(drv_data->tx_channel) |= DCSR_RUN; 972 DCSR(drv_data->tx_channel) |= DCSR_RUN;
863 if (drv_data->ssp_type != PXA25x_SSP)
864 write_SSTO(chip->timeout, reg);
865 write_SSCR1(chip->cr1
866 | chip->dma_threshold
867 | drv_data->dma_cr1,
868 reg);
869 } else { 973 } else {
870 /* Ensure we have the correct interrupt handler */ 974 /* Ensure we have the correct interrupt handler */
871 drv_data->transfer_handler = interrupt_transfer; 975 drv_data->transfer_handler = interrupt_transfer;
@@ -873,14 +977,25 @@ static void pump_transfers(unsigned long data)
873 /* Fix me, need to handle cs polarity */ 977 /* Fix me, need to handle cs polarity */
874 drv_data->cs_control(PXA2XX_CS_ASSERT); 978 drv_data->cs_control(PXA2XX_CS_ASSERT);
875 979
876 /* Go baby, go */ 980 /* Clear status */
981 cr1 = chip->cr1 | chip->threshold | drv_data->int_cr1;
877 write_SSSR(drv_data->clear_sr, reg); 982 write_SSSR(drv_data->clear_sr, reg);
983 }
984
985 /* see if we need to reload the config registers */
986 if ((read_SSCR0(reg) != cr0)
987 || (read_SSCR1(reg) & SSCR1_CHANGE_MASK) !=
988 (cr1 & SSCR1_CHANGE_MASK)) {
989
990 write_SSCR0(cr0 & ~SSCR0_SSE, reg);
878 if (drv_data->ssp_type != PXA25x_SSP) 991 if (drv_data->ssp_type != PXA25x_SSP)
879 write_SSTO(chip->timeout, reg); 992 write_SSTO(chip->timeout, reg);
880 write_SSCR1(chip->cr1 993 write_SSCR1(cr1, reg);
881 | chip->threshold 994 write_SSCR0(cr0, reg);
882 | drv_data->int_cr1, 995 } else {
883 reg); 996 if (drv_data->ssp_type != PXA25x_SSP)
997 write_SSTO(chip->timeout, reg);
998 write_SSCR1(cr1, reg);
884 } 999 }
885} 1000}
886 1001
@@ -915,9 +1030,9 @@ static void pump_messages(struct work_struct *work)
915 struct spi_transfer, 1030 struct spi_transfer,
916 transfer_list); 1031 transfer_list);
917 1032
918 /* Setup the SSP using the per chip configuration */ 1033 /* prepare to setup the SSP, in pump_transfers, using the per
1034 * chip configuration */
919 drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi); 1035 drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi);
920 restore_state(drv_data);
921 1036
922 /* Mark as busy and launch transfers */ 1037 /* Mark as busy and launch transfers */
923 tasklet_schedule(&drv_data->pump_transfers); 1038 tasklet_schedule(&drv_data->pump_transfers);
@@ -963,63 +1078,77 @@ static int setup(struct spi_device *spi)
963 spi->bits_per_word = 8; 1078 spi->bits_per_word = 8;
964 1079
965 if (drv_data->ssp_type != PXA25x_SSP 1080 if (drv_data->ssp_type != PXA25x_SSP
966 && (spi->bits_per_word < 4 || spi->bits_per_word > 32)) 1081 && (spi->bits_per_word < 4 || spi->bits_per_word > 32)) {
1082 dev_err(&spi->dev, "failed setup: ssp_type=%d, bits/wrd=%d "
1083 "b/w not 4-32 for type non-PXA25x_SSP\n",
1084 drv_data->ssp_type, spi->bits_per_word);
967 return -EINVAL; 1085 return -EINVAL;
968 else if (spi->bits_per_word < 4 || spi->bits_per_word > 16) 1086 }
1087 else if (drv_data->ssp_type == PXA25x_SSP
1088 && (spi->bits_per_word < 4
1089 || spi->bits_per_word > 16)) {
1090 dev_err(&spi->dev, "failed setup: ssp_type=%d, bits/wrd=%d "
1091 "b/w not 4-16 for type PXA25x_SSP\n",
1092 drv_data->ssp_type, spi->bits_per_word);
969 return -EINVAL; 1093 return -EINVAL;
1094 }
970 1095
971 /* Only alloc (or use chip_info) on first setup */ 1096 /* Only alloc on first setup */
972 chip = spi_get_ctldata(spi); 1097 chip = spi_get_ctldata(spi);
973 if (chip == NULL) { 1098 if (!chip) {
974 chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); 1099 chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
975 if (!chip) 1100 if (!chip) {
1101 dev_err(&spi->dev,
1102 "failed setup: can't allocate chip data\n");
976 return -ENOMEM; 1103 return -ENOMEM;
1104 }
977 1105
978 chip->cs_control = null_cs_control; 1106 chip->cs_control = null_cs_control;
979 chip->enable_dma = 0; 1107 chip->enable_dma = 0;
980 chip->timeout = SSP_TIMEOUT(1000); 1108 chip->timeout = 1000;
981 chip->threshold = SSCR1_RxTresh(1) | SSCR1_TxTresh(1); 1109 chip->threshold = SSCR1_RxTresh(1) | SSCR1_TxTresh(1);
982 chip->dma_burst_size = drv_data->master_info->enable_dma ? 1110 chip->dma_burst_size = drv_data->master_info->enable_dma ?
983 DCMD_BURST8 : 0; 1111 DCMD_BURST8 : 0;
984
985 chip_info = spi->controller_data;
986 } 1112 }
987 1113
1114 /* protocol drivers may change the chip settings, so...
1115 * if chip_info exists, use it */
1116 chip_info = spi->controller_data;
1117
988 /* chip_info isn't always needed */ 1118 /* chip_info isn't always needed */
1119 chip->cr1 = 0;
989 if (chip_info) { 1120 if (chip_info) {
990 if (chip_info->cs_control) 1121 if (chip_info->cs_control)
991 chip->cs_control = chip_info->cs_control; 1122 chip->cs_control = chip_info->cs_control;
992 1123
993 chip->timeout = SSP_TIMEOUT(chip_info->timeout_microsecs); 1124 chip->timeout = chip_info->timeout;
994 1125
995 chip->threshold = SSCR1_RxTresh(chip_info->rx_threshold) 1126 chip->threshold = (SSCR1_RxTresh(chip_info->rx_threshold) &
996 | SSCR1_TxTresh(chip_info->tx_threshold); 1127 SSCR1_RFT) |
1128 (SSCR1_TxTresh(chip_info->tx_threshold) &
1129 SSCR1_TFT);
997 1130
998 chip->enable_dma = chip_info->dma_burst_size != 0 1131 chip->enable_dma = chip_info->dma_burst_size != 0
999 && drv_data->master_info->enable_dma; 1132 && drv_data->master_info->enable_dma;
1000 chip->dma_threshold = 0; 1133 chip->dma_threshold = 0;
1001 1134
1002 if (chip->enable_dma) {
1003 if (chip_info->dma_burst_size <= 8) {
1004 chip->dma_threshold = SSCR1_RxTresh(8)
1005 | SSCR1_TxTresh(8);
1006 chip->dma_burst_size = DCMD_BURST8;
1007 } else if (chip_info->dma_burst_size <= 16) {
1008 chip->dma_threshold = SSCR1_RxTresh(16)
1009 | SSCR1_TxTresh(16);
1010 chip->dma_burst_size = DCMD_BURST16;
1011 } else {
1012 chip->dma_threshold = SSCR1_RxTresh(32)
1013 | SSCR1_TxTresh(32);
1014 chip->dma_burst_size = DCMD_BURST32;
1015 }
1016 }
1017
1018
1019 if (chip_info->enable_loopback) 1135 if (chip_info->enable_loopback)
1020 chip->cr1 = SSCR1_LBM; 1136 chip->cr1 = SSCR1_LBM;
1021 } 1137 }
1022 1138
1139 /* set dma burst and threshold outside of chip_info path so that if
1140 * chip_info goes away after setting chip->enable_dma, the
1141 * burst and threshold can still respond to changes in bits_per_word */
1142 if (chip->enable_dma) {
1143 /* set up legal burst and threshold for dma */
1144 if (set_dma_burst_and_threshold(chip, spi, spi->bits_per_word,
1145 &chip->dma_burst_size,
1146 &chip->dma_threshold)) {
1147 dev_warn(&spi->dev, "in setup: DMA burst size reduced "
1148 "to match bits_per_word\n");
1149 }
1150 }
1151
1023 if (drv_data->ioaddr == SSP1_VIRT) 1152 if (drv_data->ioaddr == SSP1_VIRT)
1024 clk_div = SSP1_SerClkDiv(spi->max_speed_hz); 1153 clk_div = SSP1_SerClkDiv(spi->max_speed_hz);
1025 else if (drv_data->ioaddr == SSP2_VIRT) 1154 else if (drv_data->ioaddr == SSP2_VIRT)
@@ -1027,7 +1156,11 @@ static int setup(struct spi_device *spi)
1027 else if (drv_data->ioaddr == SSP3_VIRT) 1156 else if (drv_data->ioaddr == SSP3_VIRT)
1028 clk_div = SSP3_SerClkDiv(spi->max_speed_hz); 1157 clk_div = SSP3_SerClkDiv(spi->max_speed_hz);
1029 else 1158 else
1159 {
1160 dev_err(&spi->dev, "failed setup: unknown IO address=0x%p\n",
1161 drv_data->ioaddr);
1030 return -ENODEV; 1162 return -ENODEV;
1163 }
1031 chip->speed_hz = spi->max_speed_hz; 1164 chip->speed_hz = spi->max_speed_hz;
1032 1165
1033 chip->cr0 = clk_div 1166 chip->cr0 = clk_div
@@ -1071,7 +1204,6 @@ static int setup(struct spi_device *spi)
1071 chip->write = u32_writer; 1204 chip->write = u32_writer;
1072 } else { 1205 } else {
1073 dev_err(&spi->dev, "invalid wordsize\n"); 1206 dev_err(&spi->dev, "invalid wordsize\n");
1074 kfree(chip);
1075 return -ENODEV; 1207 return -ENODEV;
1076 } 1208 }
1077 chip->bits_per_word = spi->bits_per_word; 1209 chip->bits_per_word = spi->bits_per_word;
@@ -1162,6 +1294,12 @@ static int destroy_queue(struct driver_data *drv_data)
1162 int status; 1294 int status;
1163 1295
1164 status = stop_queue(drv_data); 1296 status = stop_queue(drv_data);
1297 /* we are unloading the module or failing to load (only two calls
1298 * to this routine), and neither call can handle a return value.
1299 * However, destroy_workqueue calls flush_workqueue, and that will
1300 * block until all work is done. If the reason that stop_queue
1301 * timed out is that the work will never finish, then it does no
1302 * good to call destroy_workqueue, so return anyway. */
1165 if (status != 0) 1303 if (status != 0)
1166 return status; 1304 return status;
1167 1305
@@ -1360,7 +1498,16 @@ static int pxa2xx_spi_remove(struct platform_device *pdev)
1360 /* Remove the queue */ 1498 /* Remove the queue */
1361 status = destroy_queue(drv_data); 1499 status = destroy_queue(drv_data);
1362 if (status != 0) 1500 if (status != 0)
1363 return status; 1501 /* the kernel does not check the return status of this
1502 * this routine (mod->exit, within the kernel). Therefore
1503 * nothing is gained by returning from here, the module is
1504 * going away regardless, and we should not leave any more
1505 * resources allocated than necessary. We cannot free the
1506 * message memory in drv_data->queue, but we can release the
1507 * resources below. I think the kernel should honor -EBUSY
1508 * returns but... */
1509 dev_err(&pdev->dev, "pxa2xx_spi_remove: workqueue will not "
1510 "complete, message memory not freed\n");
1364 1511
1365 /* Disable the SSP at the peripheral and SOC level */ 1512 /* Disable the SSP at the peripheral and SOC level */
1366 write_SSCR0(0, drv_data->ioaddr); 1513 write_SSCR0(0, drv_data->ioaddr);
diff --git a/include/asm-arm/arch-pxa/pxa2xx_spi.h b/include/asm-arm/arch-pxa/pxa2xx_spi.h
index 915590c391c8..acc7ec7a84a1 100644
--- a/include/asm-arm/arch-pxa/pxa2xx_spi.h
+++ b/include/asm-arm/arch-pxa/pxa2xx_spi.h
@@ -27,16 +27,13 @@
27#define SSP1_SerClkDiv(x) (((CLOCK_SPEED_HZ/2/(x+1))<<8)&0x0000ff00) 27#define SSP1_SerClkDiv(x) (((CLOCK_SPEED_HZ/2/(x+1))<<8)&0x0000ff00)
28#define SSP2_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00) 28#define SSP2_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
29#define SSP3_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00) 29#define SSP3_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
30#define SSP_TIMEOUT_SCALE (2712)
31#elif defined(CONFIG_PXA27x) 30#elif defined(CONFIG_PXA27x)
32#define CLOCK_SPEED_HZ 13000000 31#define CLOCK_SPEED_HZ 13000000
33#define SSP1_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00) 32#define SSP1_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
34#define SSP2_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00) 33#define SSP2_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
35#define SSP3_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00) 34#define SSP3_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
36#define SSP_TIMEOUT_SCALE (769)
37#endif 35#endif
38 36
39#define SSP_TIMEOUT(x) ((x*10000)/SSP_TIMEOUT_SCALE)
40#define SSP1_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(1))))) 37#define SSP1_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(1)))))
41#define SSP2_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(2))))) 38#define SSP2_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(2)))))
42#define SSP3_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(3))))) 39#define SSP3_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(3)))))
@@ -63,7 +60,7 @@ struct pxa2xx_spi_chip {
63 u8 tx_threshold; 60 u8 tx_threshold;
64 u8 rx_threshold; 61 u8 rx_threshold;
65 u8 dma_burst_size; 62 u8 dma_burst_size;
66 u32 timeout_microsecs; 63 u32 timeout;
67 u8 enable_loopback; 64 u8 enable_loopback;
68 void (*cs_control)(u32 command); 65 void (*cs_control)(u32 command);
69}; 66};