133 files changed, 1526 insertions, 1885 deletions
diff --git a/Documentation/filesystems/squashfs.txt b/Documentation/filesystems/squashfs.txt
index 3e79e4a7a392..b324c033035a 100644
--- a/Documentation/filesystems/squashfs.txt
+++ b/Documentation/filesystems/squashfs.txt
@@ -22,7 +22,7 @@ Squashfs filesystem features versus Cramfs:
                                Squashfs                Cramfs
-Max filesystem size:            2^64                    16 MiB
+Max filesystem size:            2^64                    256 MiB
 Max file size:                  ~ 2 TiB                 16 MiB
 Max files:                      unlimited               unlimited
 Max directories:                unlimited               unlimited
diff --git a/Documentation/ftrace.txt b/Documentation/ftrace.txt
index 22614bef6359..fd9a3e693813 100644
--- a/Documentation/ftrace.txt
+++ b/Documentation/ftrace.txt
@@ -100,7 +100,7 @@ of ftrace. Here is a list of some of the key files:
        that is displayed in one of the above output
        files.
-  trace_max_latency:
+  tracing_max_latency:
        Some of the tracers record the max latency.
        For example, the time interrupts are disabled.
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index 134af97ff340..b7f233242315 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -347,6 +347,111 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
 void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
 #endif
+/* --------------------------------------------------------------------
+ *  Compact Flash (PCMCIA or IDE)
+ * -------------------------------------------------------------------- */
+#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE) || \
+    defined(CONFIG_BLK_DEV_IDE_AT91) || defined(CONFIG_BLK_DEV_IDE_AT91_MODULE)
+static struct at91_cf_data cf0_data;
+static struct resource cf0_resources[] = {
+        [0] = {
+                .start  = AT91_CHIPSELECT_4,
+                .end    = AT91_CHIPSELECT_4 + SZ_256M - 1,
+                .flags  = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+        }
+};
+static struct platform_device cf0_device = {
+        .id             = 0,
+        .dev            = {
+                                .platform_data  = &cf0_data,
+        },
+        .resource       = cf0_resources,
+        .num_resources  = ARRAY_SIZE(cf0_resources),
+};
+static struct at91_cf_data cf1_data;
+static struct resource cf1_resources[] = {
+        [0] = {
+                .start  = AT91_CHIPSELECT_5,
+                .end    = AT91_CHIPSELECT_5 + SZ_256M - 1,
+                .flags  = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
+        }
+};
+static struct platform_device cf1_device = {
+        .id             = 1,
+        .dev            = {
+                                .platform_data  = &cf1_data,
+        },
+        .resource       = cf1_resources,
+        .num_resources  = ARRAY_SIZE(cf1_resources),
+};
+void __init at91_add_device_cf(struct at91_cf_data *data)
+{
+        unsigned long ebi0_csa;
+        struct platform_device *pdev;
+        if (!data)
+                return;
+        /*
+         * assign CS4 or CS5 to SMC with Compact Flash logic support,
+         * we assume SMC timings are configured by board code,
+         * except True IDE where timings are controlled by driver
+         */
+        ebi0_csa = at91_sys_read(AT91_MATRIX_EBI0CSA);
+        switch (data->chipselect) {
+        case 4:
+                at91_set_A_periph(AT91_PIN_PD6, 0);  /* EBI0_NCS4/CFCS0 */
+                ebi0_csa |= AT91_MATRIX_EBI0_CS4A_SMC_CF1;
+                cf0_data = *data;
+                pdev = &cf0_device;
+                break;
+        case 5:
+                at91_set_A_periph(AT91_PIN_PD7, 0);  /* EBI0_NCS5/CFCS1 */
+                ebi0_csa |= AT91_MATRIX_EBI0_CS5A_SMC_CF2;
+                cf1_data = *data;
+                pdev = &cf1_device;
+                break;
+        default:
+                printk(KERN_ERR "AT91 CF: bad chip-select requested (%u)\n",
+                       data->chipselect);
+                return;
+        }
+        at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
+        if (data->det_pin) {
+                at91_set_gpio_input(data->det_pin, 1);
+                at91_set_deglitch(data->det_pin, 1);
+        }
+        if (data->irq_pin) {
+                at91_set_gpio_input(data->irq_pin, 1);
+                at91_set_deglitch(data->irq_pin, 1);
+        }
+        if (data->vcc_pin)
+                /* initially off */
+                at91_set_gpio_output(data->vcc_pin, 0);
+        /* enable EBI controlled pins */
+        at91_set_A_periph(AT91_PIN_PD5, 1);  /* NWAIT */
+        at91_set_A_periph(AT91_PIN_PD8, 0);  /* CFCE1 */
+        at91_set_A_periph(AT91_PIN_PD9, 0);  /* CFCE2 */
+        at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
+        pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "at91_ide" : "at91_cf";
+        platform_device_register(pdev);
+}
+#else
+void __init at91_add_device_cf(struct at91_cf_data *data) {}
+#endif
 /* --------------------------------------------------------------------
 *  NAND / SmartMedia
diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
index 0b3ae21b4565..793fe7b25f36 100644
--- a/arch/arm/mach-at91/include/mach/board.h
+++ b/arch/arm/mach-at91/include/mach/board.h
@@ -56,6 +56,9 @@ struct at91_cf_data {
        u8      vcc_pin;                /* power switching */
        u8      rst_pin;                /* card reset */
        u8      chipselect;             /* EBI Chip Select number */
+        u8      flags;
+#define AT91_CF_TRUE_IDE        0x01
+#define AT91_IDE_SWAP_A0_A2     0x02
 };
 extern void __init at91_add_device_cf(struct at91_cf_data *data);
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index 8f1f97d56e1e..0c1f86e3e44a 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -1129,6 +1129,7 @@ endchoice
 config PM_WAKEUP_BY_GPIO
        bool "Allow Wakeup from Standby by GPIO"
+        depends on PM && !BF54x
 config PM_WAKEUP_GPIO_NUMBER
        int "GPIO number"
@@ -1168,6 +1169,12 @@ config PM_BFIN_WAKE_GP
        default n
        help
          Enable General-Purpose Wake-Up (Voltage Regulator Power-Up)
+          (all processors, except ADSP-BF549). This option sets
+          the general-purpose wake-up enable (GPWE) control bit to enable
+          wake-up upon detection of an active low signal on the /GPW (PH7) pin.
+          On ADSP-BF549 this option enables the the same functionality on the
+          /MRXON pin also PH7.
 endmenu
 menu "CPU Frequency scaling"
diff --git a/arch/blackfin/Kconfig.debug b/arch/blackfin/Kconfig.debug
index 5f981d9ca625..79e7e63ab709 100644
--- a/arch/blackfin/Kconfig.debug
+++ b/arch/blackfin/Kconfig.debug
@@ -21,12 +21,6 @@ config DEBUG_STACK_USAGE
 config HAVE_ARCH_KGDB
        def_bool y
-config KGDB_TESTCASE
-        tristate "KGDB: for test case in expect"
-        default n
-        help
-          This is a kgdb test case for automated testing.
 config DEBUG_VERBOSE
        bool "Verbose fault messages"
        default y
diff --git a/arch/blackfin/configs/BF518F-EZBRD_defconfig b/arch/blackfin/configs/BF518F-EZBRD_defconfig
index 4fdb9e04759f..281f4b60e603 100644
--- a/arch/blackfin/configs/BF518F-EZBRD_defconfig
+++ b/arch/blackfin/configs/BF518F-EZBRD_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.28-rc2
+# Linux kernel version: 2.6.28
-# Fri Jan  9 17:58:41 2009
+# Fri Feb 20 10:01:44 2009
 #
 # CONFIG_MMU is not set
 # CONFIG_FPU is not set
@@ -133,10 +133,15 @@ CONFIG_BF518=y
 # CONFIG_BF538 is not set
 # CONFIG_BF539 is not set
 # CONFIG_BF542 is not set
+# CONFIG_BF542M is not set
 # CONFIG_BF544 is not set
+# CONFIG_BF544M is not set
 # CONFIG_BF547 is not set
+# CONFIG_BF547M is not set
 # CONFIG_BF548 is not set
+# CONFIG_BF548M is not set
 # CONFIG_BF549 is not set
+# CONFIG_BF549M is not set
 # CONFIG_BF561 is not set
 CONFIG_BF_REV_MIN=0
 CONFIG_BF_REV_MAX=2
@@ -426,7 +431,17 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_TIPC is not set
 # CONFIG_ATM is not set
 # CONFIG_BRIDGE is not set
-# CONFIG_NET_DSA is not set
+CONFIG_NET_DSA=y
+# CONFIG_NET_DSA_TAG_DSA is not set
+# CONFIG_NET_DSA_TAG_EDSA is not set
+# CONFIG_NET_DSA_TAG_TRAILER is not set
+CONFIG_NET_DSA_TAG_STPID=y
+# CONFIG_NET_DSA_MV88E6XXX is not set
+# CONFIG_NET_DSA_MV88E6060 is not set
+# CONFIG_NET_DSA_MV88E6XXX_NEED_PPU is not set
+# CONFIG_NET_DSA_MV88E6131 is not set
+# CONFIG_NET_DSA_MV88E6123_61_65 is not set
+CONFIG_NET_DSA_KSZ8893M=y
 # CONFIG_VLAN_8021Q is not set
 # CONFIG_DECNET is not set
 # CONFIG_LLC2 is not set
@@ -529,6 +544,8 @@ CONFIG_MTD_COMPLEX_MAPPINGS=y
 #
 # Self-contained MTD device drivers
 #
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
 # CONFIG_MTD_SLRAM is not set
 # CONFIG_MTD_PHRAM is not set
 # CONFIG_MTD_MTDRAM is not set
@@ -561,7 +578,9 @@ CONFIG_BLK_DEV_RAM_SIZE=4096
 # CONFIG_BLK_DEV_HD is not set
 CONFIG_MISC_DEVICES=y
 # CONFIG_EEPROM_93CX6 is not set
+# CONFIG_ICS932S401 is not set
 # CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_C2PORT is not set
 CONFIG_HAVE_IDE=y
 # CONFIG_IDE is not set
@@ -607,6 +626,7 @@ CONFIG_BFIN_RX_DESC_NUM=20
 # CONFIG_SMC91X is not set
 # CONFIG_SMSC911X is not set
 # CONFIG_DM9000 is not set
+# CONFIG_ENC28J60 is not set
 # CONFIG_IBM_NEW_EMAC_ZMII is not set
 # CONFIG_IBM_NEW_EMAC_RGMII is not set
 # CONFIG_IBM_NEW_EMAC_TAH is not set
@@ -764,7 +784,23 @@ CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=100
 # CONFIG_I2C_DEBUG_ALGO is not set
 # CONFIG_I2C_DEBUG_BUS is not set
 # CONFIG_I2C_DEBUG_CHIP is not set
-# CONFIG_SPI is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BFIN=y
+# CONFIG_SPI_BFIN_LOCK is not set
+# CONFIG_SPI_BITBANG is not set
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
 CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
 # CONFIG_GPIOLIB is not set
 # CONFIG_W1 is not set
@@ -788,8 +824,10 @@ CONFIG_BFIN_WDT=y
 # CONFIG_MFD_SM501 is not set
 # CONFIG_HTC_PASIC3 is not set
 # CONFIG_MFD_TMIO is not set
+# CONFIG_PMIC_DA903X is not set
 # CONFIG_MFD_WM8400 is not set
 # CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_REGULATOR is not set
 #
 # Multimedia devices
@@ -861,10 +899,18 @@ CONFIG_RTC_INTF_DEV=y
 # CONFIG_RTC_DRV_M41T80 is not set
 # CONFIG_RTC_DRV_S35390A is not set
 # CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
 #
 # SPI RTC drivers
 #
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
 #
 # Platform RTC drivers
@@ -1062,12 +1108,20 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
 # CONFIG_FAULT_INJECTION is not set
 CONFIG_SYSCTL_SYSCALL_CHECK=y
+#
+# Tracers
+#
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
 # CONFIG_DYNAMIC_PRINTK_DEBUG is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
 # CONFIG_KGDB is not set
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_KGDB_TESTCASE is not set
 CONFIG_DEBUG_VERBOSE=y
 CONFIG_DEBUG_MMRS=y
 # CONFIG_DEBUG_HWERR is not set
@@ -1100,6 +1154,7 @@ CONFIG_CRYPTO=y
 #
 # CONFIG_CRYPTO_FIPS is not set
 # CONFIG_CRYPTO_MANAGER is not set
+# CONFIG_CRYPTO_MANAGER2 is not set
 # CONFIG_CRYPTO_GF128MUL is not set
 # CONFIG_CRYPTO_NULL is not set
 # CONFIG_CRYPTO_CRYPTD is not set
diff --git a/arch/blackfin/configs/BF527-EZKIT_defconfig b/arch/blackfin/configs/BF527-EZKIT_defconfig
index 833128b39724..a50050f17706 100644
--- a/arch/blackfin/configs/BF527-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF527-EZKIT_defconfig
@@ -327,8 +327,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_MPU is not set
 #
diff --git a/arch/blackfin/configs/BF533-EZKIT_defconfig b/arch/blackfin/configs/BF533-EZKIT_defconfig
index 334c94b51c40..0a2a00d63887 100644
--- a/arch/blackfin/configs/BF533-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF533-EZKIT_defconfig
@@ -290,8 +290,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_MPU is not set
 #
diff --git a/arch/blackfin/configs/BF533-STAMP_defconfig b/arch/blackfin/configs/BF533-STAMP_defconfig
index 9d733436e300..eb027587a355 100644
--- a/arch/blackfin/configs/BF533-STAMP_defconfig
+++ b/arch/blackfin/configs/BF533-STAMP_defconfig
@@ -290,8 +290,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_MPU is not set
 #
diff --git a/arch/blackfin/configs/BF537-STAMP_defconfig b/arch/blackfin/configs/BF537-STAMP_defconfig
index 4fb4108d3103..9e62b9f40eb1 100644
--- a/arch/blackfin/configs/BF537-STAMP_defconfig
+++ b/arch/blackfin/configs/BF537-STAMP_defconfig
@@ -298,8 +298,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_MPU is not set
 #
@@ -568,15 +568,7 @@ CONFIG_MTD_PHYSMAP_BANKWIDTH=2
 # CONFIG_MTD_DOC2000 is not set
 # CONFIG_MTD_DOC2001 is not set
 # CONFIG_MTD_DOC2001PLUS is not set
-CONFIG_MTD_NAND=m
+# CONFIG_MTD_NAND is not set
-# CONFIG_MTD_NAND_VERIFY_WRITE is not set
-# CONFIG_MTD_NAND_ECC_SMC is not set
-# CONFIG_MTD_NAND_MUSEUM_IDS is not set
-# CONFIG_MTD_NAND_BFIN is not set
-CONFIG_MTD_NAND_IDS=m
-# CONFIG_MTD_NAND_DISKONCHIP is not set
-# CONFIG_MTD_NAND_NANDSIM is not set
-CONFIG_MTD_NAND_PLATFORM=m
 # CONFIG_MTD_ONENAND is not set
 #
diff --git a/arch/blackfin/configs/BF538-EZKIT_defconfig b/arch/blackfin/configs/BF538-EZKIT_defconfig
index cb32f5624a1b..dd6ad6be1c87 100644
--- a/arch/blackfin/configs/BF538-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF538-EZKIT_defconfig
@@ -306,8 +306,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_MPU is not set
 #
diff --git a/arch/blackfin/configs/BF548-EZKIT_defconfig b/arch/blackfin/configs/BF548-EZKIT_defconfig
index 0f8697618aa5..6bc2fb1b2a70 100644
--- a/arch/blackfin/configs/BF548-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF548-EZKIT_defconfig
@@ -361,8 +361,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_BFIN_L2_CACHEABLE is not set
 # CONFIG_MPU is not set
@@ -680,7 +680,7 @@ CONFIG_SCSI=y
 CONFIG_SCSI_DMA=y
 # CONFIG_SCSI_TGT is not set
 # CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
+# CONFIG_SCSI_PROC_FS is not set
 #
 # SCSI support type (disk, tape, CD-ROM)
diff --git a/arch/blackfin/configs/BF561-EZKIT_defconfig b/arch/blackfin/configs/BF561-EZKIT_defconfig
index 042c7adfccfa..69714fb3e608 100644
--- a/arch/blackfin/configs/BF561-EZKIT_defconfig
+++ b/arch/blackfin/configs/BF561-EZKIT_defconfig
@@ -329,8 +329,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_BFIN_L2_CACHEABLE is not set
 # CONFIG_MPU is not set
diff --git a/arch/blackfin/configs/BlackStamp_defconfig b/arch/blackfin/configs/BlackStamp_defconfig
index 3a20e281d23c..017c6ea071b5 100644
--- a/arch/blackfin/configs/BlackStamp_defconfig
+++ b/arch/blackfin/configs/BlackStamp_defconfig
@@ -288,8 +288,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_MPU is not set
 #
diff --git a/arch/blackfin/configs/CM-BF527_defconfig b/arch/blackfin/configs/CM-BF527_defconfig
index 865ed85a5760..d880ef786770 100644
--- a/arch/blackfin/configs/CM-BF527_defconfig
+++ b/arch/blackfin/configs/CM-BF527_defconfig
@@ -332,8 +332,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 # CONFIG_MPU is not set
 #
diff --git a/arch/blackfin/configs/CM-BF548_defconfig b/arch/blackfin/configs/CM-BF548_defconfig
index efe9741b1f14..f410430b4e3d 100644
--- a/arch/blackfin/configs/CM-BF548_defconfig
+++ b/arch/blackfin/configs/CM-BF548_defconfig
@@ -336,8 +336,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 CONFIG_L1_MAX_PIECE=16
 # CONFIG_MPU is not set
@@ -595,7 +595,7 @@ CONFIG_SCSI=y
 CONFIG_SCSI_DMA=y
 # CONFIG_SCSI_TGT is not set
 # CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
+# CONFIG_SCSI_PROC_FS is not set
 #
 # SCSI support type (disk, tape, CD-ROM)
diff --git a/arch/blackfin/configs/IP0X_defconfig b/arch/blackfin/configs/IP0X_defconfig
index eae83b5de92f..7db93874c987 100644
--- a/arch/blackfin/configs/IP0X_defconfig
+++ b/arch/blackfin/configs/IP0X_defconfig
@@ -612,7 +612,7 @@ CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
 CONFIG_SCSI=y
 # CONFIG_SCSI_TGT is not set
 # CONFIG_SCSI_NETLINK is not set
-CONFIG_SCSI_PROC_FS=y
+# CONFIG_SCSI_PROC_FS is not set
 #
 # SCSI support type (disk, tape, CD-ROM)
diff --git a/arch/blackfin/configs/SRV1_defconfig b/arch/blackfin/configs/SRV1_defconfig
index fa580affc9d6..a46529c6ade3 100644
--- a/arch/blackfin/configs/SRV1_defconfig
+++ b/arch/blackfin/configs/SRV1_defconfig
@@ -282,8 +282,8 @@ CONFIG_BFIN_ICACHE=y
 CONFIG_BFIN_DCACHE=y
 # CONFIG_BFIN_DCACHE_BANKA is not set
 # CONFIG_BFIN_ICACHE_LOCK is not set
-# CONFIG_BFIN_WB is not set
+CONFIG_BFIN_WB=y
-CONFIG_BFIN_WT=y
+# CONFIG_BFIN_WT is not set
 CONFIG_L1_MAX_PIECE=16
 #
diff --git a/arch/blackfin/include/asm/Kbuild b/arch/blackfin/include/asm/Kbuild
index 606ecfdcc962..09c31418cc08 100644
--- a/arch/blackfin/include/asm/Kbuild
+++ b/arch/blackfin/include/asm/Kbuild
@@ -1,3 +1,4 @@
 include include/asm-generic/Kbuild.asm
+unifdef-y += bfin_sport.h
 unifdef-y += fixed_code.h
diff --git a/arch/blackfin/include/asm/bfin_sport.h b/arch/blackfin/include/asm/bfin_sport.h
index fe88a2c19213..65a651db5b07 100644
--- a/arch/blackfin/include/asm/bfin_sport.h
+++ b/arch/blackfin/include/asm/bfin_sport.h
@@ -1,30 +1,9 @@
 /*
- * File:         include/asm-blackfin/bfin_sport.h
+ * bfin_sport.h - userspace header for bfin sport driver
- * Based on:
- * Author:       Roy Huang (roy.huang@analog.com)
 *
- * Created:      Thu Aug. 24 2006
+ * Copyright 2004-2008 Analog Devices Inc.
- * Description:
 *
- * Modified:
+ * Licensed under the GPL-2 or later.
- *               Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs:         Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 */
 #ifndef __BFIN_SPORT_H__
@@ -42,11 +21,10 @@
 #define NORM_FORMAT     0x0
 #define ALAW_FORMAT     0x2
 #define ULAW_FORMAT     0x3
-struct sport_register;
 /* Function driver which use sport must initialize the structure */
 struct sport_config {
-        /*TDM (multichannels), I2S or other mode */
+        /* TDM (multichannels), I2S or other mode */
        unsigned int mode:3;
        /* if TDM mode is selected, channels must be set */
@@ -72,12 +50,18 @@ struct sport_config {
        int serial_clk;
        int fsync_clk;
-        unsigned int data_format:2;     /*Normal, u-law or a-law */
+        unsigned int data_format:2;     /* Normal, u-law or a-law */
        int word_len;           /* How length of the word in bits, 3-32 bits */
        int dma_enabled;
 };
+/* Userspace interface */
+#define SPORT_IOC_MAGIC         'P'
+#define SPORT_IOC_CONFIG        _IOWR('P', 0x01, struct sport_config)
+#ifdef __KERNEL__
 struct sport_register {
        unsigned short tcr1;
        unsigned short reserved0;
@@ -117,9 +101,6 @@ struct sport_register {
        unsigned long mrcs3;
 };
-#define SPORT_IOC_MAGIC         'P'
-#define SPORT_IOC_CONFIG        _IOWR('P', 0x01, struct sport_config)
 struct sport_dev {
        struct cdev cdev;       /* Char device structure */
@@ -149,6 +130,8 @@ struct sport_dev {
        struct sport_config config;
 };
+#endif
 #define SPORT_TCR1      0
 #define SPORT_TCR2      1
 #define SPORT_TCLKDIV   2
@@ -169,4 +152,4 @@ struct sport_dev {
 #define SPORT_MRCS2     22
 #define SPORT_MRCS3     23
-#endif                          /*__BFIN_SPORT_H__*/
+#endif
diff --git a/arch/blackfin/include/asm/ipipe.h b/arch/blackfin/include/asm/ipipe.h
index 76f53d8b9a0d..343b56361ec9 100644
--- a/arch/blackfin/include/asm/ipipe.h
+++ b/arch/blackfin/include/asm/ipipe.h
@@ -35,9 +35,9 @@
 #include <asm/atomic.h>
 #include <asm/traps.h>
-#define IPIPE_ARCH_STRING     "1.8-00"
+#define IPIPE_ARCH_STRING     "1.9-00"
 #define IPIPE_MAJOR_NUMBER    1
-#define IPIPE_MINOR_NUMBER    8
+#define IPIPE_MINOR_NUMBER    9
 #define IPIPE_PATCH_NUMBER    0
 #ifdef CONFIG_SMP
@@ -83,9 +83,9 @@ struct ipipe_sysinfo {
                                "%2 = CYCLES2\n"                \
                                "CC = %2 == %0\n"               \
                                "if ! CC jump 1b\n"             \
-                                : "=r" (((unsigned long *)&t)[1]),      \
+                                : "=d,a" (((unsigned long *)&t)[1]),    \
-                                  "=r" (((unsigned long *)&t)[0]),      \
+                                  "=d,a" (((unsigned long *)&t)[0]),    \
-                                  "=r" (__cy2)                          \
+                                  "=d,a" (__cy2)                                \
                                : /*no input*/ : "CC");                 \
        t;                                                              \
        })
@@ -118,35 +118,40 @@ void __ipipe_disable_irqdesc(struct ipipe_domain *ipd,
 #define __ipipe_disable_irq(irq)        (irq_desc[irq].chip->mask(irq))
-#define __ipipe_lock_root()                                     \
+static inline int __ipipe_check_tickdev(const char *devname)
-        set_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags)
+{
+        return 1;
+}
-#define __ipipe_unlock_root()                                   \
+static inline void __ipipe_lock_root(void)
-        clear_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags)
+{
+        set_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status));
+}
+static inline void __ipipe_unlock_root(void)
+{
+        clear_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status));
+}
 void __ipipe_enable_pipeline(void);
 #define __ipipe_hook_critical_ipi(ipd) do { } while (0)
-#define __ipipe_sync_pipeline(syncmask)                                 \
+#define __ipipe_sync_pipeline  ___ipipe_sync_pipeline
-        do {                                                            \
+void ___ipipe_sync_pipeline(unsigned long syncmask);
-                struct ipipe_domain *ipd = ipipe_current_domain;        \
-                if (likely(ipd != ipipe_root_domain || !test_bit(IPIPE_ROOTLOCK_FLAG, &ipd->flags))) \
-                        __ipipe_sync_stage(syncmask);                   \
-        } while (0)
 void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs);
 int __ipipe_get_irq_priority(unsigned irq);
-int __ipipe_get_irqthread_priority(unsigned irq);
 void __ipipe_stall_root_raw(void);
 void __ipipe_unstall_root_raw(void);
 void __ipipe_serial_debug(const char *fmt, ...);
+asmlinkage void __ipipe_call_irqtail(unsigned long addr);
 DECLARE_PER_CPU(struct pt_regs, __ipipe_tick_regs);
 extern unsigned long __ipipe_core_clock;
@@ -162,42 +167,25 @@ static inline unsigned long __ipipe_ffnz(unsigned long ul)
 #define __ipipe_run_irqtail()  /* Must be a macro */                    \
        do {                                                            \
-                asmlinkage void __ipipe_call_irqtail(void);             \
                unsigned long __pending;                                \
-                CSYNC();                                        \
+                CSYNC();                                                \
                __pending = bfin_read_IPEND();                          \
                if (__pending & 0x8000) {                               \
                        __pending &= ~0x8010;                           \
                        if (__pending && (__pending & (__pending - 1)) == 0) \
-                                __ipipe_call_irqtail();                 \
+                                __ipipe_call_irqtail(__ipipe_irq_tail_hook); \
                }                                                       \
        } while (0)
 #define __ipipe_run_isr(ipd, irq)                                       \
        do {                                                            \
                if (ipd == ipipe_root_domain) {                         \
-                        /*                                              \
+                        local_irq_enable_hw();                          \
-                         * Note: the I-pipe implements a threaded interrupt model on \
+                        if (ipipe_virtual_irq_p(irq))                   \
-                         * this arch for Linux external IRQs. The interrupt handler we \
-                         * call here only wakes up the associated IRQ thread. \
-                         */                                             \
-                        if (ipipe_virtual_irq_p(irq)) {                 \
-                                /* No irqtail here; virtual interrupts have no effect \
-                                   on IPEND so there is no need for processing \
-                                   deferral. */                         \
-                                local_irq_enable_nohead(ipd);           \
                                ipd->irqs[irq].handler(irq, ipd->irqs[irq].cookie); \
-                                local_irq_disable_nohead(ipd);          \
+                        else                                            \
-                        } else                                          \
-                                /*                                      \
-                                 * No need to run the irqtail here either; \
-                                 * we can't be preempted by hw IRQs, so \
-                                 * non-Linux IRQs cannot stack over the short \
-                                 * thread wakeup code. Which in turn means \
-                                 * that no irqtail condition could be pending \
-                                 * for domains above Linux in the pipeline. \
-                                 */                                     \
                                ipd->irqs[irq].handler(irq, &__raw_get_cpu_var(__ipipe_tick_regs)); \
+                        local_irq_disable_hw();                         \
                } else {                                                \
                        __clear_bit(IPIPE_SYNC_FLAG, &ipipe_cpudom_var(ipd, status)); \
                        local_irq_enable_nohead(ipd);                   \
@@ -217,42 +205,24 @@ void ipipe_init_irq_threads(void);
 int ipipe_start_irq_thread(unsigned irq, struct irq_desc *desc);
-#define IS_SYSIRQ(irq)          ((irq) > IRQ_CORETMR && (irq) <= SYS_IRQS)
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
-#define IS_GPIOIRQ(irq)         ((irq) >= GPIO_IRQ_BASE && (irq) < NR_IRQS)
+#define IRQ_SYSTMR              IRQ_CORETMR
+#define IRQ_PRIOTMR             IRQ_CORETMR
+#else
 #define IRQ_SYSTMR              IRQ_TIMER0
 #define IRQ_PRIOTMR             CONFIG_IRQ_TIMER0
+#endif
-#if defined(CONFIG_BF531) || defined(CONFIG_BF532) || defined(CONFIG_BF533)
+#ifdef CONFIG_BF561
-#define PRIO_GPIODEMUX(irq)     CONFIG_PFA
-#elif defined(CONFIG_BF534) || defined(CONFIG_BF536) || defined(CONFIG_BF537)
-#define PRIO_GPIODEMUX(irq)     CONFIG_IRQ_PROG_INTA
-#elif defined(CONFIG_BF52x)
-#define PRIO_GPIODEMUX(irq)     ((irq) == IRQ_PORTF_INTA ? CONFIG_IRQ_PORTF_INTA : \
-                                 (irq) == IRQ_PORTG_INTA ? CONFIG_IRQ_PORTG_INTA : \
-                                 (irq) == IRQ_PORTH_INTA ? CONFIG_IRQ_PORTH_INTA : \
-                                 -1)
-#elif defined(CONFIG_BF561)
-#define PRIO_GPIODEMUX(irq)     ((irq) == IRQ_PROG0_INTA ? CONFIG_IRQ_PROG0_INTA : \
-                                 (irq) == IRQ_PROG1_INTA ? CONFIG_IRQ_PROG1_INTA : \
-                                 (irq) == IRQ_PROG2_INTA ? CONFIG_IRQ_PROG2_INTA : \
-                                 -1)
 #define bfin_write_TIMER_DISABLE(val)   bfin_write_TMRS8_DISABLE(val)
 #define bfin_write_TIMER_ENABLE(val)    bfin_write_TMRS8_ENABLE(val)
 #define bfin_write_TIMER_STATUS(val)    bfin_write_TMRS8_STATUS(val)
 #define bfin_read_TIMER_STATUS()        bfin_read_TMRS8_STATUS()
 #elif defined(CONFIG_BF54x)
-#define PRIO_GPIODEMUX(irq)     ((irq) == IRQ_PINT0 ? CONFIG_IRQ_PINT0 : \
-                                 (irq) == IRQ_PINT1 ? CONFIG_IRQ_PINT1 : \
-                                 (irq) == IRQ_PINT2 ? CONFIG_IRQ_PINT2 : \
-                                 (irq) == IRQ_PINT3 ? CONFIG_IRQ_PINT3 : \
-                                 -1)
 #define bfin_write_TIMER_DISABLE(val)   bfin_write_TIMER_DISABLE0(val)
 #define bfin_write_TIMER_ENABLE(val)    bfin_write_TIMER_ENABLE0(val)
 #define bfin_write_TIMER_STATUS(val)    bfin_write_TIMER_STATUS0(val)
 #define bfin_read_TIMER_STATUS(val)     bfin_read_TIMER_STATUS0(val)
-#else
-# error "no PRIO_GPIODEMUX() for this part"
 #endif
 #define __ipipe_root_tick_p(regs)       ((regs->ipend & 0x10) != 0)
@@ -275,4 +245,6 @@ int ipipe_start_irq_thread(unsigned irq, struct irq_desc *desc);
 #endif /* !CONFIG_IPIPE */
+#define ipipe_update_tick_evtdev(evtdev)        do { } while (0)
 #endif  /* !__ASM_BLACKFIN_IPIPE_H */
diff --git a/arch/blackfin/include/asm/ipipe_base.h b/arch/blackfin/include/asm/ipipe_base.h
index cb1025aeabcf..3e8acbd1a3be 100644
--- a/arch/blackfin/include/asm/ipipe_base.h
+++ b/arch/blackfin/include/asm/ipipe_base.h
@@ -1,5 +1,5 @@
 /*   -*- linux-c -*-
- *   include/asm-blackfin/_baseipipe.h
+ *   include/asm-blackfin/ipipe_base.h
 *
 *   Copyright (C) 2007 Philippe Gerum.
 *
@@ -27,8 +27,9 @@
 #define IPIPE_NR_XIRQS          NR_IRQS
 #define IPIPE_IRQ_ISHIFT        5       /* 2^5 for 32bits arch. */
-/* Blackfin-specific, global domain flags */
+/* Blackfin-specific, per-cpu pipeline status */
-#define IPIPE_ROOTLOCK_FLAG     1       /* Lock pipeline for root */
+#define IPIPE_SYNCDEFER_FLAG    15
+#define IPIPE_SYNCDEFER_MASK    (1L << IPIPE_SYNCDEFER_MASK)
 /* Blackfin traps -- i.e. exception vector numbers */
 #define IPIPE_NR_FAULTS         52 /* We leave a gap after VEC_ILL_RES. */
@@ -48,11 +49,6 @@
 #ifndef __ASSEMBLY__
-#include <linux/bitops.h>
-extern int test_bit(int nr, const void *addr);
 extern unsigned long __ipipe_root_status; /* Alias to ipipe_root_cpudom_var(status) */
 static inline void __ipipe_stall_root(void)
diff --git a/arch/blackfin/include/asm/irq.h b/arch/blackfin/include/asm/irq.h
index 3d977909ce7d..7645e85a5f6f 100644
--- a/arch/blackfin/include/asm/irq.h
+++ b/arch/blackfin/include/asm/irq.h
@@ -61,20 +61,38 @@ void __ipipe_restore_root(unsigned long flags);
 #define raw_irqs_disabled_flags(flags)  (!irqs_enabled_from_flags_hw(flags))
 #define local_test_iflag_hw(x)          irqs_enabled_from_flags_hw(x)
-#define local_save_flags(x)                                             \
+#define local_save_flags(x)                                      \
-        do {                                                            \
+        do {                                                     \
-                (x) = __ipipe_test_root() ? \
+                (x) = __ipipe_test_root() ?                      \
                        __all_masked_irq_flags : bfin_irq_flags; \
+                barrier();                                       \
        } while (0)
-#define local_irq_save(x)                               \
+#define local_irq_save(x)                                        \
-        do {                                            \
+        do {                                                     \
-                (x) = __ipipe_test_and_stall_root();    \
+                (x) = __ipipe_test_and_stall_root() ?            \
+                        __all_masked_irq_flags : bfin_irq_flags; \
+                barrier();                                       \
+        } while (0)
+static inline void local_irq_restore(unsigned long x)
+{
+        barrier();
+        __ipipe_restore_root(x == __all_masked_irq_flags);
+}
+#define local_irq_disable()                     \
+        do {                                    \
+                __ipipe_stall_root();           \
+                barrier();                      \
        } while (0)
-#define local_irq_restore(x)    __ipipe_restore_root(x)
+static inline void local_irq_enable(void)
-#define local_irq_disable()     __ipipe_stall_root()
+{
-#define local_irq_enable()      __ipipe_unstall_root()
+        barrier();
+        __ipipe_unstall_root();
+}
 #define irqs_disabled()         __ipipe_test_root()
 #define local_save_flags_hw(x) \
diff --git a/arch/blackfin/include/asm/thread_info.h b/arch/blackfin/include/asm/thread_info.h
index e721ce55956c..2920087516f2 100644
--- a/arch/blackfin/include/asm/thread_info.h
+++ b/arch/blackfin/include/asm/thread_info.h
@@ -122,6 +122,7 @@ static inline struct thread_info *current_thread_info(void)
 #define TIF_MEMDIE              4
 #define TIF_RESTORE_SIGMASK     5       /* restore signal mask in do_signal() */
 #define TIF_FREEZE              6       /* is freezing for suspend */
+#define TIF_IRQ_SYNC            7       /* sync pipeline stage */
 /* as above, but as bit values */
 #define _TIF_SYSCALL_TRACE      (1<<TIF_SYSCALL_TRACE)
@@ -130,6 +131,7 @@ static inline struct thread_info *current_thread_info(void)
 #define _TIF_POLLING_NRFLAG     (1<<TIF_POLLING_NRFLAG)
 #define _TIF_RESTORE_SIGMASK    (1<<TIF_RESTORE_SIGMASK)
 #define _TIF_FREEZE             (1<<TIF_FREEZE)
+#define _TIF_IRQ_SYNC           (1<<TIF_IRQ_SYNC)
 #define _TIF_WORK_MASK          0x0000FFFE      /* work to do on interrupt/exception return */
diff --git a/arch/blackfin/kernel/Makefile b/arch/blackfin/kernel/Makefile
index 4a92a86824b7..fd4d4328a0f2 100644
--- a/arch/blackfin/kernel/Makefile
+++ b/arch/blackfin/kernel/Makefile
@@ -15,13 +15,15 @@ else
    obj-y += time.o
 endif
-CFLAGS_kgdb_test.o := -mlong-calls -O0
 obj-$(CONFIG_IPIPE)                  += ipipe.o
 obj-$(CONFIG_IPIPE_TRACE_MCOUNT)     += mcount.o
 obj-$(CONFIG_BFIN_GPTIMERS)          += gptimers.o
 obj-$(CONFIG_CPLB_INFO)              += cplbinfo.o
 obj-$(CONFIG_MODULES)                += module.o
 obj-$(CONFIG_KGDB)                   += kgdb.o
-obj-$(CONFIG_KGDB_TESTCASE)          += kgdb_test.o
+obj-$(CONFIG_KGDB_TESTS)             += kgdb_test.o
 obj-$(CONFIG_EARLY_PRINTK)           += early_printk.o
+# the kgdb test puts code into L2 and without linker
+# relaxation, we need to force long calls to/from it
+CFLAGS_kgdb_test.o := -mlong-calls -O0
diff --git a/arch/blackfin/kernel/cplb-nompu/cplbinit.c b/arch/blackfin/kernel/cplb-nompu/cplbinit.c
index 0e28f7595733..d6c067782e63 100644
--- a/arch/blackfin/kernel/cplb-nompu/cplbinit.c
+++ b/arch/blackfin/kernel/cplb-nompu/cplbinit.c
@@ -53,9 +53,13 @@ void __init generate_cplb_tables_cpu(unsigned int cpu)
        i_d = i_i = 0;
+#ifdef CONFIG_DEBUG_HUNT_FOR_ZERO
        /* Set up the zero page.  */
        d_tbl[i_d].addr = 0;
        d_tbl[i_d++].data = SDRAM_OOPS | PAGE_SIZE_1KB;
+        i_tbl[i_i].addr = 0;
+        i_tbl[i_i++].data = SDRAM_OOPS | PAGE_SIZE_1KB;
+#endif
        /* Cover kernel memory with 4M pages.  */
        addr = 0;
diff --git a/arch/blackfin/kernel/ipipe.c b/arch/blackfin/kernel/ipipe.c
index 339be5a3ae6a..a5de8d45424c 100644
--- a/arch/blackfin/kernel/ipipe.c
+++ b/arch/blackfin/kernel/ipipe.c
@@ -35,14 +35,8 @@
 #include <asm/atomic.h>
 #include <asm/io.h>
-static int create_irq_threads;
 DEFINE_PER_CPU(struct pt_regs, __ipipe_tick_regs);
-static DEFINE_PER_CPU(unsigned long, pending_irqthread_mask);
-static DEFINE_PER_CPU(int [IVG13 + 1], pending_irq_count);
 asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs);
 static void __ipipe_no_irqtail(void);
@@ -93,6 +87,7 @@ void __ipipe_enable_pipeline(void)
 */
 void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
 {
+        struct ipipe_percpu_domain_data *p = ipipe_root_cpudom_ptr();
        struct ipipe_domain *this_domain, *next_domain;
        struct list_head *head, *pos;
        int m_ack, s = -1;
@@ -104,7 +99,6 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
         * interrupt.
         */
        m_ack = (regs == NULL || irq == IRQ_SYSTMR || irq == IRQ_CORETMR);
        this_domain = ipipe_current_domain;
        if (unlikely(test_bit(IPIPE_STICKY_FLAG, &this_domain->irqs[irq].control)))
@@ -114,49 +108,28 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
                next_domain = list_entry(head, struct ipipe_domain, p_link);
                if (likely(test_bit(IPIPE_WIRED_FLAG, &next_domain->irqs[irq].control))) {
                        if (!m_ack && next_domain->irqs[irq].acknowledge != NULL)
-                                next_domain->irqs[irq].acknowledge(irq, irq_desc + irq);
+                                next_domain->irqs[irq].acknowledge(irq, irq_to_desc(irq));
-                        if (test_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags))
+                        if (test_bit(IPIPE_SYNCDEFER_FLAG, &p->status))
-                                s = __test_and_set_bit(IPIPE_STALL_FLAG,
+                                s = __test_and_set_bit(IPIPE_STALL_FLAG, &p->status);
-                                                       &ipipe_root_cpudom_var(status));
                        __ipipe_dispatch_wired(next_domain, irq);
-                                goto finalize;
+                        goto out;
-                        return;
                }
        }
        /* Ack the interrupt. */
        pos = head;
        while (pos != &__ipipe_pipeline) {
                next_domain = list_entry(pos, struct ipipe_domain, p_link);
-                /*
-                 * For each domain handling the incoming IRQ, mark it
-                 * as pending in its log.
-                 */
                if (test_bit(IPIPE_HANDLE_FLAG, &next_domain->irqs[irq].control)) {
-                        /*
-                         * Domains that handle this IRQ are polled for
-                         * acknowledging it by decreasing priority
-                         * order. The interrupt must be made pending
-                         * _first_ in the domain's status flags before
-                         * the PIC is unlocked.
-                         */
                        __ipipe_set_irq_pending(next_domain, irq);
                        if (!m_ack && next_domain->irqs[irq].acknowledge != NULL) {
-                                next_domain->irqs[irq].acknowledge(irq, irq_desc + irq);
+                                next_domain->irqs[irq].acknowledge(irq, irq_to_desc(irq));
                                m_ack = 1;
                        }
                }
-                /*
-                 * If the domain does not want the IRQ to be passed
-                 * down the interrupt pipe, exit the loop now.
-                 */
                if (!test_bit(IPIPE_PASS_FLAG, &next_domain->irqs[irq].control))
                        break;
                pos = next_domain->p_link.next;
        }
@@ -166,18 +139,24 @@ void __ipipe_handle_irq(unsigned irq, struct pt_regs *regs)
         * immediately to the current domain if the interrupt has been
         * marked as 'sticky'. This search does not go beyond the
         * current domain in the pipeline. We also enforce the
-         * additional root stage lock (blackfin-specific). */
+         * additional root stage lock (blackfin-specific).
+         */
+        if (test_bit(IPIPE_SYNCDEFER_FLAG, &p->status))
+                s = __test_and_set_bit(IPIPE_STALL_FLAG, &p->status);
-        if (test_bit(IPIPE_ROOTLOCK_FLAG, &ipipe_root_domain->flags))
+        /*
-                s = __test_and_set_bit(IPIPE_STALL_FLAG,
+         * If the interrupt preempted the head domain, then do not
-                                       &ipipe_root_cpudom_var(status));
+         * even try to walk the pipeline, unless an interrupt is
-finalize:
+         * pending for it.
+         */
+        if (test_bit(IPIPE_AHEAD_FLAG, &this_domain->flags) &&
+            ipipe_head_cpudom_var(irqpend_himask) == 0)
+                goto out;
        __ipipe_walk_pipeline(head);
+out:
        if (!s)
-                __clear_bit(IPIPE_STALL_FLAG,
+                __clear_bit(IPIPE_STALL_FLAG, &p->status);
-                            &ipipe_root_cpudom_var(status));
 }
 int __ipipe_check_root(void)
@@ -187,7 +166,7 @@ int __ipipe_check_root(void)
 void __ipipe_enable_irqdesc(struct ipipe_domain *ipd, unsigned irq)
 {
-        struct irq_desc *desc = irq_desc + irq;
+        struct irq_desc *desc = irq_to_desc(irq);
        int prio = desc->ic_prio;
        desc->depth = 0;
@@ -199,7 +178,7 @@ EXPORT_SYMBOL(__ipipe_enable_irqdesc);
 void __ipipe_disable_irqdesc(struct ipipe_domain *ipd, unsigned irq)
 {
-        struct irq_desc *desc = irq_desc + irq;
+        struct irq_desc *desc = irq_to_desc(irq);
        int prio = desc->ic_prio;
        if (ipd != &ipipe_root &&
@@ -236,15 +215,18 @@ int __ipipe_syscall_root(struct pt_regs *regs)
 {
        unsigned long flags;
-        /* We need to run the IRQ tail hook whenever we don't
+        /*
+         * We need to run the IRQ tail hook whenever we don't
         * propagate a syscall to higher domains, because we know that
         * important operations might be pending there (e.g. Xenomai
-         * deferred rescheduling). */
+         * deferred rescheduling).
+         */
-        if (!__ipipe_syscall_watched_p(current, regs->orig_p0)) {
+        if (regs->orig_p0 < NR_syscalls) {
                void (*hook)(void) = (void (*)(void))__ipipe_irq_tail_hook;
                hook();
-                return 0;
+                if ((current->flags & PF_EVNOTIFY) == 0)
+                        return 0;
        }
        /*
@@ -312,112 +294,46 @@ int ipipe_trigger_irq(unsigned irq)
 {
        unsigned long flags;
+#ifdef CONFIG_IPIPE_DEBUG
        if (irq >= IPIPE_NR_IRQS ||
            (ipipe_virtual_irq_p(irq)
             && !test_bit(irq - IPIPE_VIRQ_BASE, &__ipipe_virtual_irq_map)))
                return -EINVAL;
+#endif
        local_irq_save_hw(flags);
        __ipipe_handle_irq(irq, NULL);
        local_irq_restore_hw(flags);
        return 1;
 }
-/* Move Linux IRQ to threads. */
+asmlinkage void __ipipe_sync_root(void)
-static int do_irqd(void *__desc)
 {
-        struct irq_desc *desc = __desc;
+        unsigned long flags;
-        unsigned irq = desc - irq_desc;
-        int thrprio = desc->thr_prio;
-        int thrmask = 1 << thrprio;
-        int cpu = smp_processor_id();
-        cpumask_t cpumask;
-        sigfillset(&current->blocked);
-        current->flags |= PF_NOFREEZE;
-        cpumask = cpumask_of_cpu(cpu);
-        set_cpus_allowed(current, cpumask);
-        ipipe_setscheduler_root(current, SCHED_FIFO, 50 + thrprio);
-        while (!kthread_should_stop()) {
-                local_irq_disable();
-                if (!(desc->status & IRQ_SCHEDULED)) {
-                        set_current_state(TASK_INTERRUPTIBLE);
-resched:
-                        local_irq_enable();
-                        schedule();
-                        local_irq_disable();
-                }
-                __set_current_state(TASK_RUNNING);
-                /*
-                 * If higher priority interrupt servers are ready to
-                 * run, reschedule immediately. We need this for the
-                 * GPIO demux IRQ handler to unmask the interrupt line
-                 * _last_, after all GPIO IRQs have run.
-                 */
-                if (per_cpu(pending_irqthread_mask, cpu) & ~(thrmask|(thrmask-1)))
-                        goto resched;
-                if (--per_cpu(pending_irq_count[thrprio], cpu) == 0)
-                        per_cpu(pending_irqthread_mask, cpu) &= ~thrmask;
-                desc->status &= ~IRQ_SCHEDULED;
-                desc->thr_handler(irq, &__raw_get_cpu_var(__ipipe_tick_regs));
-                local_irq_enable();
-        }
-        __set_current_state(TASK_RUNNING);
-        return 0;
-}
-static void kick_irqd(unsigned irq, void *cookie)
+        BUG_ON(irqs_disabled());
-{
-        struct irq_desc *desc = irq_desc + irq;
-        int thrprio = desc->thr_prio;
-        int thrmask = 1 << thrprio;
-        int cpu = smp_processor_id();
-        if (!(desc->status & IRQ_SCHEDULED)) {
-                desc->status |= IRQ_SCHEDULED;
-                per_cpu(pending_irqthread_mask, cpu) |= thrmask;
-                ++per_cpu(pending_irq_count[thrprio], cpu);
-                wake_up_process(desc->thread);
-        }
-}
-int ipipe_start_irq_thread(unsigned irq, struct irq_desc *desc)
+        local_irq_save_hw(flags);
-{
-        if (desc->thread || !create_irq_threads)
-                return 0;
-        desc->thread = kthread_create(do_irqd, desc, "IRQ %d", irq);
-        if (desc->thread == NULL) {
-                printk(KERN_ERR "irqd: could not create IRQ thread %d!\n", irq);
-                return -ENOMEM;
-        }
-        wake_up_process(desc->thread);
+        clear_thread_flag(TIF_IRQ_SYNC);
-        desc->thr_handler = ipipe_root_domain->irqs[irq].handler;
+        if (ipipe_root_cpudom_var(irqpend_himask) != 0)
-        ipipe_root_domain->irqs[irq].handler = &kick_irqd;
+                __ipipe_sync_pipeline(IPIPE_IRQMASK_ANY);
-        return 0;
+        local_irq_restore_hw(flags);
 }
-void __init ipipe_init_irq_threads(void)
+void ___ipipe_sync_pipeline(unsigned long syncmask)
 {
-        unsigned irq;
+        struct ipipe_domain *ipd = ipipe_current_domain;
-        struct irq_desc *desc;
-        create_irq_threads = 1;
-        for (irq = 0; irq < NR_IRQS; irq++) {
+        if (ipd == ipipe_root_domain) {
-                desc = irq_desc + irq;
+                if (test_bit(IPIPE_SYNCDEFER_FLAG, &ipipe_root_cpudom_var(status)))
-                if (desc->action != NULL ||
+                        return;
-                        (desc->status & IRQ_NOREQUEST) != 0)
-                        ipipe_start_irq_thread(irq, desc);
        }
+        __ipipe_sync_stage(syncmask);
 }
 EXPORT_SYMBOL(show_stack);
diff --git a/arch/blackfin/kernel/irqchip.c b/arch/blackfin/kernel/irqchip.c
index 23e9aa080710..1ab5b532ec72 100644
--- a/arch/blackfin/kernel/irqchip.c
+++ b/arch/blackfin/kernel/irqchip.c
@@ -149,11 +149,15 @@ asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs)
 #endif
        generic_handle_irq(irq);
-#ifndef CONFIG_IPIPE    /* Useless and bugous over the I-pipe: IRQs are threaded. */
+#ifndef CONFIG_IPIPE
-        /* If we're the only interrupt running (ignoring IRQ15 which is for
+        /*
-           syscalls), lower our priority to IRQ14 so that softirqs run at
+         * If we're the only interrupt running (ignoring IRQ15 which
-           that level.  If there's another, lower-level interrupt, irq_exit
+         * is for syscalls), lower our priority to IRQ14 so that
-           will defer softirqs to that.  */
+         * softirqs run at that level.  If there's another,
+         * lower-level interrupt, irq_exit will defer softirqs to
+         * that. If the interrupt pipeline is enabled, we are already
+         * running at IRQ14 priority, so we don't need this code.
+         */
        CSYNC();
        pending = bfin_read_IPEND() & ~0x8000;
        other_ints = pending & (pending - 1);
diff --git a/arch/blackfin/kernel/kgdb_test.c b/arch/blackfin/kernel/kgdb_test.c
index 3dba9c17304a..dbcf3e45cb0b 100644
--- a/arch/blackfin/kernel/kgdb_test.c
+++ b/arch/blackfin/kernel/kgdb_test.c
@@ -20,6 +20,7 @@
 static char cmdline[256];
 static unsigned long len;
+#ifndef CONFIG_SMP
 static int num1 __attribute__((l1_data));
 void kgdb_l1_test(void) __attribute__((l1_text));
@@ -32,6 +33,8 @@ void kgdb_l1_test(void)
        printk(KERN_ALERT "L1(after change) : data variable addr = 0x%p, data value is %d\n", &num1, num1);
        return ;
 }
+#endif
 #if L2_LENGTH
 static int num2 __attribute__((l2));
@@ -59,10 +62,12 @@ int kgdb_test(char *name, int len, int count, int z)
 static int test_proc_output(char *buf)
 {
        kgdb_test("hello world!", 12, 0x55, 0x10);
+#ifndef CONFIG_SMP
        kgdb_l1_test();
-        #if L2_LENGTH
+#endif
+#if L2_LENGTH
        kgdb_l2_test();
-        #endif
+#endif
        return 0;
 }
diff --git a/arch/blackfin/kernel/ptrace.c b/arch/blackfin/kernel/ptrace.c
index 594e325b40e4..d76618db50df 100644
--- a/arch/blackfin/kernel/ptrace.c
+++ b/arch/blackfin/kernel/ptrace.c
@@ -45,6 +45,7 @@
 #include <asm/asm-offsets.h>
 #include <asm/dma.h>
 #include <asm/fixed_code.h>
+#include <asm/cacheflush.h>
 #include <asm/mem_map.h>
 #define TEXT_OFFSET 0
@@ -240,7 +241,7 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
                        } else if (addr >= FIXED_CODE_START
                            && addr + sizeof(tmp) <= FIXED_CODE_END) {
-                                memcpy(&tmp, (const void *)(addr), sizeof(tmp));
+                                copy_from_user_page(0, 0, 0, &tmp, (const void *)(addr), sizeof(tmp));
                                copied = sizeof(tmp);
                        } else
@@ -320,7 +321,7 @@ long arch_ptrace(struct task_struct *child, long request, long addr, long data)
                        } else if (addr >= FIXED_CODE_START
                            && addr + sizeof(data) <= FIXED_CODE_END) {
-                                memcpy((void *)(addr), &data, sizeof(data));
+                                copy_to_user_page(0, 0, 0, (void *)(addr), &data, sizeof(data));
                                copied = sizeof(data);
                        } else
diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index e5c116230800..a58687bdee6a 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -889,6 +889,10 @@ void __init setup_arch(char **cmdline_p)
                               CPU, bfin_revid());
        }
+        /* We can't run on BF548-0.1 due to ANOMALY 05000448 */
+        if (bfin_cpuid() == 0x27de && bfin_revid() == 1)
+                panic("You can't run on this processor due to 05000448\n");
        printk(KERN_INFO "Blackfin Linux support by http://blackfin.uclinux.org/\n");
        printk(KERN_INFO "Processor Speed: %lu MHz core clock and %lu MHz System Clock\n",
@@ -1141,12 +1145,12 @@ static int show_cpuinfo(struct seq_file *m, void *v)
                icache_size = 0;
        seq_printf(m, "cache size\t: %d KB(L1 icache) "
-                "%d KB(L1 dcache-%s) %d KB(L2 cache)\n",
+                "%d KB(L1 dcache%s) %d KB(L2 cache)\n",
                icache_size, dcache_size,
 #if defined CONFIG_BFIN_WB
-                "wb"
+                "-wb"
 #elif defined CONFIG_BFIN_WT
-                "wt"
+                "-wt"
 #endif
                "", 0);
diff --git a/arch/blackfin/kernel/time.c b/arch/blackfin/kernel/time.c
index 172b4c588467..1bbacfbd4c5d 100644
--- a/arch/blackfin/kernel/time.c
+++ b/arch/blackfin/kernel/time.c
@@ -134,7 +134,10 @@ irqreturn_t timer_interrupt(int irq, void *dummy)
        write_seqlock(&xtime_lock);
 #if defined(CONFIG_TICK_SOURCE_SYSTMR0) && !defined(CONFIG_IPIPE)
-/* FIXME: Here TIMIL0 is not set when IPIPE enabled, why? */
+        /*
+         * TIMIL0 is latched in __ipipe_grab_irq() when the I-Pipe is
+         * enabled.
+         */
        if (get_gptimer_status(0) & TIMER_STATUS_TIMIL0) {
 #endif
                do_timer(1);
diff --git a/arch/blackfin/mach-bf518/boards/ezbrd.c b/arch/blackfin/mach-bf518/boards/ezbrd.c
index 0e175342112e..41f2eacfef20 100644
--- a/arch/blackfin/mach-bf518/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf518/boards/ezbrd.c
@@ -113,7 +113,6 @@ static struct platform_device bfin_mac_device = {
        .name = "bfin_mac",
        .dev.platform_data = &bfin_mii_bus,
 };
-#endif
 #if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
 static struct dsa_platform_data ksz8893m_switch_data = {
@@ -132,6 +131,7 @@ static struct platform_device ksz8893m_switch_device = {
        .dev.platform_data = &ksz8893m_switch_data,
 };
 #endif
+#endif
 #if defined(CONFIG_MTD_M25P80) \
        || defined(CONFIG_MTD_M25P80_MODULE)
@@ -171,6 +171,7 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 #if defined(CONFIG_NET_DSA_KSZ8893M) \
        || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
 /* SPI SWITCH CHIP */
@@ -179,10 +180,11 @@ static struct bfin5xx_spi_chip spi_switch_info = {
        .bits_per_word = 8,
 };
 #endif
+#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -259,6 +261,7 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 #if defined(CONFIG_NET_DSA_KSZ8893M) \
        || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
        {
@@ -271,24 +274,15 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .mode = SPI_MODE_3,
        },
 #endif
+#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
-                .modalias = "spi_mmc_dummy",
+                .modalias = "mmc_spi",
                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = 0,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
-        {
-                .modalias = "spi_mmc",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
@@ -630,11 +624,10 @@ static struct platform_device *stamp_devices[] __initdata = {
 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
        &bfin_mii_bus,
        &bfin_mac_device,
-#endif
 #if defined(CONFIG_NET_DSA_KSZ8893M) || defined(CONFIG_NET_DSA_KSZ8893M_MODULE)
        &ksz8893m_switch_device,
 #endif
+#endif
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
        &bfin_spi0_device,
diff --git a/arch/blackfin/mach-bf518/include/mach/anomaly.h b/arch/blackfin/mach-bf518/include/mach/anomaly.h
index e5b4bef0edae..c847bb101076 100644
--- a/arch/blackfin/mach-bf518/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf518/include/mach/anomaly.h
@@ -2,12 +2,12 @@
 * File: include/asm-blackfin/mach-bf518/anomaly.h
 * Bugs: Enter bugs at http://blackfin.uclinux.org/
 *
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
 * Licensed under the GPL-2 or later.
 */
 /* This file shoule be up to date with:
- *  - ????
+ *  - Revision B, 02/03/2009; ADSP-BF512/BF514/BF516/BF518 Blackfin Processor Anomaly List
 */
 #ifndef _MACH_ANOMALY_H_
@@ -19,6 +19,8 @@
 #define ANOMALY_05000122 (1)
 /* False Hardware Error from an Access in the Shadow of a Conditional Branch */
 #define ANOMALY_05000245 (1)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (1)
 /* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
 #define ANOMALY_05000265 (1)
 /* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
@@ -53,6 +55,12 @@
 #define ANOMALY_05000443 (1)
 /* Incorrect L1 Instruction Bank B Memory Map Location */
 #define ANOMALY_05000444 (1)
+/* Incorrect Default Hysteresis Setting for RESET, NMI, and BMODE Signals */
+#define ANOMALY_05000452 (1)
+/* PWM_TRIPB Signal Not Available on PG10 */
+#define ANOMALY_05000453 (1)
+/* PPI_FS3 is Driven One Half Cycle Later Than PPI Data */
+#define ANOMALY_05000455 (1)
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000125 (0)
@@ -65,15 +73,20 @@
 #define ANOMALY_05000263 (0)
 #define ANOMALY_05000266 (0)
 #define ANOMALY_05000273 (0)
+#define ANOMALY_05000278 (0)
 #define ANOMALY_05000285 (0)
+#define ANOMALY_05000305 (0)
 #define ANOMALY_05000307 (0)
 #define ANOMALY_05000311 (0)
 #define ANOMALY_05000312 (0)
 #define ANOMALY_05000323 (0)
 #define ANOMALY_05000353 (0)
 #define ANOMALY_05000363 (0)
+#define ANOMALY_05000380 (0)
 #define ANOMALY_05000386 (0)
 #define ANOMALY_05000412 (0)
 #define ANOMALY_05000432 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
 #endif
diff --git a/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
index b50a63b975a2..e21c1c3e4ec7 100644
--- a/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
         CH_UART0_TX,
         CH_UART0_RX,
 #endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
         CONFIG_UART0_CTS_PIN,
         CONFIG_UART0_RTS_PIN,
 #endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
         CH_UART1_TX,
         CH_UART1_RX,
 #endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
         CONFIG_UART1_CTS_PIN,
         CONFIG_UART1_RTS_PIN,
 #endif
diff --git a/arch/blackfin/mach-bf527/boards/cm_bf527.c b/arch/blackfin/mach-bf527/boards/cm_bf527.c
index 856c097b5317..48e69eecdba4 100644
--- a/arch/blackfin/mach-bf527/boards/cm_bf527.c
+++ b/arch/blackfin/mach-bf527/boards/cm_bf527.c
@@ -487,9 +487,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -585,23 +585,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad9960_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
-                .modalias = "spi_mmc_dummy",
+                .modalias = "mmc_spi",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 0,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
-        {
-                .modalias = "spi_mmc",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf527/boards/ezbrd.c b/arch/blackfin/mach-bf527/boards/ezbrd.c
index 83606fcdde27..7fe480e4ebe8 100644
--- a/arch/blackfin/mach-bf527/boards/ezbrd.c
+++ b/arch/blackfin/mach-bf527/boards/ezbrd.c
@@ -256,9 +256,9 @@ static struct bfin5xx_spi_chip spi_adc_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -366,23 +366,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
-                .modalias = "spi_mmc_dummy",
+                .modalias = "mmc_spi",
                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = 0,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
-        {
-                .modalias = "spi_mmc",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf527/include/mach/anomaly.h b/arch/blackfin/mach-bf527/include/mach/anomaly.h
index 035e8d835058..df6808d8a6ef 100644
--- a/arch/blackfin/mach-bf527/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf527/include/mach/anomaly.h
@@ -2,7 +2,7 @@
 * File: include/asm-blackfin/mach-bf527/anomaly.h
 * Bugs: Enter bugs at http://blackfin.uclinux.org/
 *
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
 * Licensed under the GPL-2 or later.
 */
@@ -167,12 +167,16 @@
 #define ANOMALY_05000263 (0)
 #define ANOMALY_05000266 (0)
 #define ANOMALY_05000273 (0)
+#define ANOMALY_05000278 (0)
 #define ANOMALY_05000285 (0)
+#define ANOMALY_05000305 (0)
 #define ANOMALY_05000307 (0)
 #define ANOMALY_05000311 (0)
 #define ANOMALY_05000312 (0)
 #define ANOMALY_05000323 (0)
 #define ANOMALY_05000363 (0)
 #define ANOMALY_05000412 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
 #endif
diff --git a/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
index 75722d6008b0..e8c41fd842b5 100644
--- a/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
         CH_UART0_TX,
         CH_UART0_RX,
 #endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
         CONFIG_UART0_CTS_PIN,
         CONFIG_UART0_RTS_PIN,
 #endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
         CH_UART1_TX,
         CH_UART1_RX,
 #endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
         CONFIG_UART1_CTS_PIN,
         CONFIG_UART1_RTS_PIN,
 #endif
diff --git a/arch/blackfin/mach-bf533/boards/Kconfig b/arch/blackfin/mach-bf533/boards/Kconfig
index 308c98dc5aba..8d8b3e7321e6 100644
--- a/arch/blackfin/mach-bf533/boards/Kconfig
+++ b/arch/blackfin/mach-bf533/boards/Kconfig
@@ -38,9 +38,4 @@ config BFIN532_IP0X
        help
          Core support for IP04/IP04 open hardware IP-PBX.
-config GENERIC_BF533_BOARD
-        bool "Generic"
-        help
-          Generic or Custom board support.
 endchoice
diff --git a/arch/blackfin/mach-bf533/boards/Makefile b/arch/blackfin/mach-bf533/boards/Makefile
index 9afbe72b484f..ff1e832f80d2 100644
--- a/arch/blackfin/mach-bf533/boards/Makefile
+++ b/arch/blackfin/mach-bf533/boards/Makefile
@@ -2,7 +2,6 @@
 # arch/blackfin/mach-bf533/boards/Makefile
 #
-obj-$(CONFIG_GENERIC_BF533_BOARD)      += generic_board.o
 obj-$(CONFIG_BFIN533_STAMP)            += stamp.o
 obj-$(CONFIG_BFIN532_IP0X)             += ip0x.o
 obj-$(CONFIG_BFIN533_EZKIT)            += ezkit.o
diff --git a/arch/blackfin/mach-bf533/boards/blackstamp.c b/arch/blackfin/mach-bf533/boards/blackstamp.c
index 015c18f85e7f..0765872a8ada 100644
--- a/arch/blackfin/mach-bf533/boards/blackstamp.c
+++ b/arch/blackfin/mach-bf533/boards/blackstamp.c
@@ -101,9 +101,9 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -129,23 +129,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-        {
-                .modalias = "spi_mmc_dummy",
-                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 0,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
        {
-                .modalias = "spi_mmc",
+                .modalias = "mmc_spi",
                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf533/boards/cm_bf533.c b/arch/blackfin/mach-bf533/boards/cm_bf533.c
index e7061c7e8c42..e8974878d8c2 100644
--- a/arch/blackfin/mach-bf533/boards/cm_bf533.c
+++ b/arch/blackfin/mach-bf533/boards/cm_bf533.c
@@ -96,9 +96,9 @@ static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -138,23 +138,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-        {
-                .modalias = "spi_mmc_dummy",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 0,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
        {
-                .modalias = "spi_mmc",
+                .modalias = "mmc_spi",
                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf533/boards/generic_board.c b/arch/blackfin/mach-bf533/boards/generic_board.c
deleted file mode 100644
index 986eeec53b1f..000000000000
--- a/arch/blackfin/mach-bf533/boards/generic_board.c
+++ /dev/null
@@ -1,126 +0,0 @@
-/*
- * File:         arch/blackfin/mach-bf533/generic_board.c
- * Based on:     arch/blackfin/mach-bf533/ezkit.c
- * Author:       Aidan Williams <aidan@nicta.com.au>
- *
- * Created:      2005
- * Description:
- *
- * Modified:
- *               Copyright 2005 National ICT Australia (NICTA)
- *               Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs:         Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
- */
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-/*
- * Name the Board for the /proc/cpuinfo
- */
-const char bfin_board_name[] = "UNKNOWN BOARD";
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-static struct platform_device rtc_device = {
-        .name = "rtc-bfin",
-        .id   = -1,
-};
-#endif
-/*
- *  Driver needs to know address, irq and flag pin.
- */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-static struct resource smc91x_resources[] = {
-        {
-                .start = 0x20300300,
-                .end = 0x20300300 + 16,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = IRQ_PROG_INTB,
-                .end = IRQ_PROG_INTB,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        }, {
-                .start = IRQ_PF7,
-                .end = IRQ_PF7,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        },
-};
-static struct platform_device smc91x_device = {
-        .name = "smc91x",
-        .id = 0,
-        .num_resources = ARRAY_SIZE(smc91x_resources),
-        .resource = smc91x_resources,
-};
-#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
-        {
-                .start = 0xFFC00400,
-                .end = 0xFFC004FF,
-                .flags = IORESOURCE_MEM,
-        },
-        {
-                .start = IRQ_UART0_RX,
-                .end = IRQ_UART0_RX+1,
-                .flags = IORESOURCE_IRQ,
-        },
-        {
-                .start = CH_UART0_RX,
-                .end = CH_UART0_RX+1,
-                .flags = IORESOURCE_DMA,
-        },
-};
-static struct platform_device bfin_sir0_device = {
-        .name = "bfin_sir",
-        .id = 0,
-        .num_resources = ARRAY_SIZE(bfin_sir0_resources),
-        .resource = bfin_sir0_resources,
-};
-#endif
-#endif
-static struct platform_device *generic_board_devices[] __initdata = {
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-        &rtc_device,
-#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-        &smc91x_device,
-#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-        &bfin_sir0_device,
-#endif
-#endif
-};
-static int __init generic_board_init(void)
-{
-        printk(KERN_INFO "%s(): registering device resources\n", __func__);
-        return platform_add_devices(generic_board_devices, ARRAY_SIZE(generic_board_devices));
-}
-arch_initcall(generic_board_init);
diff --git a/arch/blackfin/mach-bf533/boards/ip0x.c b/arch/blackfin/mach-bf533/boards/ip0x.c
index e30b1b7d1442..f19b63378b12 100644
--- a/arch/blackfin/mach-bf533/boards/ip0x.c
+++ b/arch/blackfin/mach-bf533/boards/ip0x.c
@@ -127,8 +127,8 @@ static struct platform_device dm9000_device2 = {
 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 /* all SPI peripherals info goes here */
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
 /*
 * CPOL (Clock Polarity)
 *  0 - Active high SCK
@@ -152,14 +152,13 @@ static struct bfin5xx_spi_chip spi_mmc_chip_info = {
 /* Notice: for blackfin, the speed_hz is the value of register
 * SPI_BAUD, not the real baudrate */
 static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
-                .modalias = "spi_mmc",
+                .modalias = "mmc_spi",
                .max_speed_hz = 2,
                .bus_num = 1,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
        },
 #endif
 };
diff --git a/arch/blackfin/mach-bf533/include/mach/anomaly.h b/arch/blackfin/mach-bf533/include/mach/anomaly.h
index 0d3a03429fb9..1cf893e2e55b 100644
--- a/arch/blackfin/mach-bf533/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf533/include/mach/anomaly.h
@@ -2,7 +2,7 @@
 * File: include/asm-blackfin/mach-bf533/anomaly.h
 * Bugs: Enter bugs at http://blackfin.uclinux.org/
 *
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
 * Licensed under the GPL-2 or later.
 */
@@ -160,7 +160,7 @@
 #define ANOMALY_05000301 (__SILICON_REVISION__ < 6)
 /* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
 #define ANOMALY_05000302 (__SILICON_REVISION__ < 5)
-/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */
 #define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
 /* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */
 #define ANOMALY_05000306 (__SILICON_REVISION__ < 5)
@@ -278,9 +278,12 @@
 #define ANOMALY_05000266 (0)
 #define ANOMALY_05000323 (0)
 #define ANOMALY_05000353 (1)
+#define ANOMALY_05000380 (0)
 #define ANOMALY_05000386 (1)
 #define ANOMALY_05000412 (0)
 #define ANOMALY_05000432 (0)
 #define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
 #endif
diff --git a/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
index f3d9e495230c..5f517f53b0fd 100644
--- a/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
@@ -134,7 +134,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART_TX,
        CH_UART_RX,
 #endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART0_CTS_PIN,
        CONFIG_UART0_RTS_PIN,
 #endif
diff --git a/arch/blackfin/mach-bf537/boards/Kconfig b/arch/blackfin/mach-bf537/boards/Kconfig
index 42a57b0acb29..77c59da87e85 100644
--- a/arch/blackfin/mach-bf537/boards/Kconfig
+++ b/arch/blackfin/mach-bf537/boards/Kconfig
@@ -33,9 +33,4 @@ config CAMSIG_MINOTAUR
        help
          Board supply package for CSP Minotaur
-config GENERIC_BF537_BOARD
-        bool "Generic"
-        help
-          Generic or Custom board support.
 endchoice
diff --git a/arch/blackfin/mach-bf537/boards/Makefile b/arch/blackfin/mach-bf537/boards/Makefile
index 7168cc14afd8..68b98a7af6a6 100644
--- a/arch/blackfin/mach-bf537/boards/Makefile
+++ b/arch/blackfin/mach-bf537/boards/Makefile
@@ -2,7 +2,6 @@
 # arch/blackfin/mach-bf537/boards/Makefile
 #
-obj-$(CONFIG_GENERIC_BF537_BOARD)      += generic_board.o
 obj-$(CONFIG_BFIN537_STAMP)            += stamp.o
 obj-$(CONFIG_BFIN537_BLUETECHNIX_CM)   += cm_bf537.o
 obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM)  += tcm_bf537.o
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
index 9cd8fb2a30d3..41c75b9bfac0 100644
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537.c
@@ -108,9 +108,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -160,23 +160,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-        {
-                .modalias = "spi_mmc_dummy",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 7,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
        {
-                .modalias = "spi_mmc",
+                .modalias = "mmc_spi",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
+                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 1,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf537/boards/generic_board.c b/arch/blackfin/mach-bf537/boards/generic_board.c
deleted file mode 100644
index da710fdc4569..000000000000
--- a/arch/blackfin/mach-bf537/boards/generic_board.c
+++ /dev/null
@@ -1,745 +0,0 @@
-/*
- * File:         arch/blackfin/mach-bf537/boards/generic_board.c
- * Based on:     arch/blackfin/mach-bf533/boards/ezkit.c
- * Author:       Aidan Williams <aidan@nicta.com.au>
- *
- * Created:
- * Description:
- *
- * Modified:
- *               Copyright 2005 National ICT Australia (NICTA)
- *               Copyright 2004-2008 Analog Devices Inc.
- *
- * Bugs:         Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
- */
-#include <linux/device.h>
-#include <linux/etherdevice.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/usb/sl811.h>
-#include <asm/dma.h>
-#include <asm/bfin5xx_spi.h>
-#include <asm/reboot.h>
-#include <asm/portmux.h>
-#include <linux/spi/ad7877.h>
-/*
- * Name the Board for the /proc/cpuinfo
- */
-const char bfin_board_name[] = "UNKNOWN BOARD";
-/*
- *  Driver needs to know address, irq and flag pin.
- */
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
-#include <linux/usb/isp1760.h>
-static struct resource bfin_isp1760_resources[] = {
-        [0] = {
-                .start  = 0x203C0000,
-                .end    = 0x203C0000 + 0x000fffff,
-                .flags  = IORESOURCE_MEM,
-        },
-        [1] = {
-                .start  = IRQ_PF7,
-                .end    = IRQ_PF7,
-                .flags  = IORESOURCE_IRQ,
-        },
-};
-static struct isp1760_platform_data isp1760_priv = {
-        .is_isp1761 = 0,
-        .port1_disable = 0,
-        .bus_width_16 = 1,
-        .port1_otg = 0,
-        .analog_oc = 0,
-        .dack_polarity_high = 0,
-        .dreq_polarity_high = 0,
-};
-static struct platform_device bfin_isp1760_device = {
-        .name           = "isp1760-hcd",
-        .id             = 0,
-        .dev = {
-                .platform_data = &isp1760_priv,
-        },
-        .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
-        .resource       = bfin_isp1760_resources,
-};
-#endif
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
-static struct resource bfin_pcmcia_cf_resources[] = {
-        {
-                .start = 0x20310000, /* IO PORT */
-                .end = 0x20312000,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = 0x20311000, /* Attribute Memory */
-                .end = 0x20311FFF,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = IRQ_PF4,
-                .end = IRQ_PF4,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
-        }, {
-                .start = 6, /* Card Detect PF6 */
-                .end = 6,
-                .flags = IORESOURCE_IRQ,
-        },
-};
-static struct platform_device bfin_pcmcia_cf_device = {
-        .name = "bfin_cf_pcmcia",
-        .id = -1,
-        .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
-        .resource = bfin_pcmcia_cf_resources,
-};
-#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-static struct platform_device rtc_device = {
-        .name = "rtc-bfin",
-        .id   = -1,
-};
-#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-static struct resource smc91x_resources[] = {
-        {
-                .name = "smc91x-regs",
-                .start = 0x20300300,
-                .end = 0x20300300 + 16,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = IRQ_PF7,
-                .end = IRQ_PF7,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        },
-};
-static struct platform_device smc91x_device = {
-        .name = "smc91x",
-        .id = 0,
-        .num_resources = ARRAY_SIZE(smc91x_resources),
-        .resource = smc91x_resources,
-};
-#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
-static struct resource dm9000_resources[] = {
-        [0] = {
-                .start  = 0x203FB800,
-                .end    = 0x203FB800 + 1,
-                .flags  = IORESOURCE_MEM,
-        },
-        [1] = {
-                .start  = 0x203FB800 + 4,
-                .end    = 0x203FB800 + 5,
-                .flags  = IORESOURCE_MEM,
-        },
-        [2] = {
-                .start  = IRQ_PF9,
-                .end    = IRQ_PF9,
-                .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
-        },
-};
-static struct platform_device dm9000_device = {
-        .name           = "dm9000",
-        .id             = -1,
-        .num_resources  = ARRAY_SIZE(dm9000_resources),
-        .resource       = dm9000_resources,
-};
-#endif
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-static struct resource sl811_hcd_resources[] = {
-        {
-                .start = 0x20340000,
-                .end = 0x20340000,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = 0x20340004,
-                .end = 0x20340004,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = CONFIG_USB_SL811_BFIN_IRQ,
-                .end = CONFIG_USB_SL811_BFIN_IRQ,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        },
-};
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-void sl811_port_power(struct device *dev, int is_on)
-{
-        gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
-        gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
-}
-#endif
-static struct sl811_platform_data sl811_priv = {
-        .potpg = 10,
-        .power = 250,       /* == 500mA */
-#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
-        .port_power = &sl811_port_power,
-#endif
-};
-static struct platform_device sl811_hcd_device = {
-        .name = "sl811-hcd",
-        .id = 0,
-        .dev = {
-                .platform_data = &sl811_priv,
-        },
-        .num_resources = ARRAY_SIZE(sl811_hcd_resources),
-        .resource = sl811_hcd_resources,
-};
-#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
-        {
-                .start = 0x20360000,
-                .end = 0x20360000,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = 0x20360004,
-                .end = 0x20360004,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
-                .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        },
-};
-static struct isp1362_platform_data isp1362_priv = {
-        .sel15Kres = 1,
-        .clknotstop = 0,
-        .oc_enable = 0,
-        .int_act_high = 0,
-        .int_edge_triggered = 0,
-        .remote_wakeup_connected = 0,
-        .no_power_switching = 1,
-        .power_switching_mode = 0,
-};
-static struct platform_device isp1362_hcd_device = {
-        .name = "isp1362-hcd",
-        .id = 0,
-        .dev = {
-                .platform_data = &isp1362_priv,
-        },
-        .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
-        .resource = isp1362_hcd_resources,
-};
-#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-static struct platform_device bfin_mii_bus = {
-        .name = "bfin_mii_bus",
-};
-static struct platform_device bfin_mac_device = {
-        .name = "bfin_mac",
-        .dev.platform_data = &bfin_mii_bus,
-};
-#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
-static struct resource net2272_bfin_resources[] = {
-        {
-                .start = 0x20300000,
-                .end = 0x20300000 + 0x100,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = IRQ_PF7,
-                .end = IRQ_PF7,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        },
-};
-static struct platform_device net2272_bfin_device = {
-        .name = "net2272",
-        .id = -1,
-        .num_resources = ARRAY_SIZE(net2272_bfin_resources),
-        .resource = net2272_bfin_resources,
-};
-#endif
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-/* all SPI peripherals info goes here */
-#if defined(CONFIG_MTD_M25P80) \
-        || defined(CONFIG_MTD_M25P80_MODULE)
-static struct mtd_partition bfin_spi_flash_partitions[] = {
-        {
-                .name = "bootloader(spi)",
-                .size = 0x00020000,
-                .offset = 0,
-                .mask_flags = MTD_CAP_ROM
-        }, {
-                .name = "linux kernel(spi)",
-                .size = 0xe0000,
-                .offset = 0x20000
-        }, {
-                .name = "file system(spi)",
-                .size = 0x700000,
-                .offset = 0x00100000,
-        }
-};
-static struct flash_platform_data bfin_spi_flash_data = {
-        .name = "m25p80",
-        .parts = bfin_spi_flash_partitions,
-        .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
-        .type = "m25p64",
-};
-/* SPI flash chip (m25p64) */
-static struct bfin5xx_spi_chip spi_flash_chip_info = {
-        .enable_dma = 0,         /* use dma transfer with this chip*/
-        .bits_per_word = 8,
-};
-#endif
-#if defined(CONFIG_SPI_ADC_BF533) \
-        || defined(CONFIG_SPI_ADC_BF533_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
-        .enable_dma = 1,         /* use dma transfer with this chip*/
-        .bits_per_word = 16,
-};
-#endif
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
-        || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
-        .enable_dma = 0,
-        .bits_per_word = 16,
-};
-#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
-        .enable_dma = 0,
-        .bits_per_word = 16,
-};
-#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
-        .enable_dma = 1,
-        .bits_per_word = 8,
-};
-#endif
-#if defined(CONFIG_PBX)
-static struct bfin5xx_spi_chip spi_si3xxx_chip_info = {
-        .ctl_reg        = 0x4, /* send zero */
-        .enable_dma     = 0,
-        .bits_per_word  = 8,
-        .cs_change_per_word = 1,
-};
-#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
-        .enable_dma = 0,
-        .bits_per_word = 16,
-};
-static const struct ad7877_platform_data bfin_ad7877_ts_info = {
-        .model                  = 7877,
-        .vref_delay_usecs       = 50,   /* internal, no capacitor */
-        .x_plate_ohms           = 419,
-        .y_plate_ohms           = 486,
-        .pressure_max           = 1000,
-        .pressure_min           = 0,
-        .stopacq_polarity       = 1,
-        .first_conversion_delay = 3,
-        .acquisition_time       = 1,
-        .averaging              = 1,
-        .pen_down_acc_interval  = 1,
-};
-#endif
-static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) \
-        || defined(CONFIG_MTD_M25P80_MODULE)
-        {
-                /* the modalias must be the same as spi device driver name */
-                .modalias = "m25p80", /* Name of spi_driver for this device */
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0, /* Framework bus number */
-                .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
-                .platform_data = &bfin_spi_flash_data,
-                .controller_data = &spi_flash_chip_info,
-                .mode = SPI_MODE_3,
-        },
-#endif
-#if defined(CONFIG_SPI_ADC_BF533) \
-        || defined(CONFIG_SPI_ADC_BF533_MODULE)
-        {
-                .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
-                .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0, /* Framework bus number */
-                .chip_select = 1, /* Framework chip select. */
-                .platform_data = NULL, /* No spi_driver specific config */
-                .controller_data = &spi_adc_chip_info,
-        },
-#endif
-#if defined(CONFIG_SND_BLACKFIN_AD1836) \
-        || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
-        {
-                .modalias = "ad1836-spi",
-                .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
-                .controller_data = &ad1836_spi_chip_info,
-        },
-#endif
-#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE)
-        {
-                .modalias = "ad9960-spi",
-                .max_speed_hz = 10000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 1,
-                .controller_data = &ad9960_spi_chip_info,
-        },
-#endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
-        {
-                .modalias = "spi_mmc_dummy",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 0,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
-        {
-                .modalias = "spi_mmc",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
-#endif
-#if defined(CONFIG_PBX)
-        {
-                .modalias = "fxs-spi",
-                .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 8 - CONFIG_J11_JUMPER,
-                .controller_data = &spi_si3xxx_chip_info,
-                .mode = SPI_MODE_3,
-        },
-        {
-                .modalias = "fxo-spi",
-                .max_speed_hz = 12500000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 8 - CONFIG_J19_JUMPER,
-                .controller_data = &spi_si3xxx_chip_info,
-                .mode = SPI_MODE_3,
-        },
-#endif
-#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-        {
-                .modalias               = "ad7877",
-                .platform_data          = &bfin_ad7877_ts_info,
-                .irq                    = IRQ_PF6,
-                .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num        = 0,
-                .chip_select  = 1,
-                .controller_data = &spi_ad7877_chip_info,
-        },
-#endif
-};
-/* SPI controller data */
-static struct bfin5xx_spi_master bfin_spi0_info = {
-        .num_chipselect = 8,
-        .enable_dma = 1,  /* master has the ability to do dma transfer */
-        .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
-};
-/* SPI (0) */
-static struct resource bfin_spi0_resource[] = {
-        [0] = {
-                .start = SPI0_REGBASE,
-                .end   = SPI0_REGBASE + 0xFF,
-                .flags = IORESOURCE_MEM,
-                },
-        [1] = {
-                .start = CH_SPI,
-                .end   = CH_SPI,
-                .flags = IORESOURCE_IRQ,
-        },
-};
-static struct platform_device bfin_spi0_device = {
-        .name = "bfin-spi",
-        .id = 0, /* Bus number */
-        .num_resources = ARRAY_SIZE(bfin_spi0_resource),
-        .resource = bfin_spi0_resource,
-        .dev = {
-                .platform_data = &bfin_spi0_info, /* Passed to driver */
-        },
-};
-#endif  /* spi master and devices */
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
-static struct platform_device bfin_fb_device = {
-        .name = "bf537-lq035",
-};
-#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
-static struct platform_device bfin_fb_adv7393_device = {
-        .name = "bfin-adv7393",
-};
-#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
-        {
-                .start = 0xFFC00400,
-                .end = 0xFFC004FF,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = 0xFFC02000,
-                .end = 0xFFC020FF,
-                .flags = IORESOURCE_MEM,
-        },
-};
-static struct platform_device bfin_uart_device = {
-        .name = "bfin-uart",
-        .id = 1,
-        .num_resources = ARRAY_SIZE(bfin_uart_resources),
-        .resource = bfin_uart_resources,
-};
-#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
-        {
-                .start = 0xFFC00400,
-                .end = 0xFFC004FF,
-                .flags = IORESOURCE_MEM,
-        },
-        {
-                .start = IRQ_UART0_RX,
-                .end = IRQ_UART0_RX+1,
-                .flags = IORESOURCE_IRQ,
-        },
-        {
-                .start = CH_UART0_RX,
-                .end = CH_UART0_RX+1,
-                .flags = IORESOURCE_DMA,
-        },
-};
-static struct platform_device bfin_sir0_device = {
-        .name = "bfin_sir",
-        .id = 0,
-        .num_resources = ARRAY_SIZE(bfin_sir0_resources),
-        .resource = bfin_sir0_resources,
-};
-#endif
-#ifdef CONFIG_BFIN_SIR1
-static struct resource bfin_sir1_resources[] = {
-        {
-                .start = 0xFFC02000,
-                .end = 0xFFC020FF,
-                .flags = IORESOURCE_MEM,
-        },
-        {
-                .start = IRQ_UART1_RX,
-                .end = IRQ_UART1_RX+1,
-                .flags = IORESOURCE_IRQ,
-        },
-        {
-                .start = CH_UART1_RX,
-                .end = CH_UART1_RX+1,
-                .flags = IORESOURCE_DMA,
-        },
-};
-static struct platform_device bfin_sir1_device = {
-        .name = "bfin_sir",
-        .id = 1,
-        .num_resources = ARRAY_SIZE(bfin_sir1_resources),
-        .resource = bfin_sir1_resources,
-};
-#endif
-#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
-static struct resource bfin_twi0_resource[] = {
-        [0] = {
-                .start = TWI0_REGBASE,
-                .end   = TWI0_REGBASE + 0xFF,
-                .flags = IORESOURCE_MEM,
-        },
-        [1] = {
-                .start = IRQ_TWI,
-                .end   = IRQ_TWI,
-                .flags = IORESOURCE_IRQ,
-        },
-};
-static struct platform_device i2c_bfin_twi_device = {
-        .name = "i2c-bfin-twi",
-        .id = 0,
-        .num_resources = ARRAY_SIZE(bfin_twi0_resource),
-        .resource = bfin_twi0_resource,
-};
-#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
-static struct platform_device bfin_sport0_uart_device = {
-        .name = "bfin-sport-uart",
-        .id = 0,
-};
-static struct platform_device bfin_sport1_uart_device = {
-        .name = "bfin-sport-uart",
-        .id = 1,
-};
-#endif
-static struct platform_device *stamp_devices[] __initdata = {
-#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
-        &bfin_pcmcia_cf_device,
-#endif
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-        &rtc_device,
-#endif
-#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
-        &sl811_hcd_device,
-#endif
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-        &isp1362_hcd_device,
-#endif
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-        &smc91x_device,
-#endif
-#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
-        &dm9000_device,
-#endif
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-        &bfin_mii_bus,
-        &bfin_mac_device,
-#endif
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
-        &net2272_bfin_device,
-#endif
-#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
-        &bfin_isp1760_device,
-#endif
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-        &bfin_spi0_device,
-#endif
-#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
-        &bfin_fb_device,
-#endif
-#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
-        &bfin_fb_adv7393_device,
-#endif
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-        &bfin_uart_device,
-#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-        &bfin_sir0_device,
-#endif
-#ifdef CONFIG_BFIN_SIR1
-        &bfin_sir1_device,
-#endif
-#endif
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
-        &i2c_bfin_twi_device,
-#endif
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
-        &bfin_sport0_uart_device,
-        &bfin_sport1_uart_device,
-#endif
-};
-static int __init generic_init(void)
-{
-        printk(KERN_INFO "%s(): registering device resources\n", __func__);
-        platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-        spi_register_board_info(bfin_spi_board_info,
-                                ARRAY_SIZE(bfin_spi_board_info));
-#endif
-        return 0;
-}
-arch_initcall(generic_init);
-void native_machine_restart(char *cmd)
-{
-        /* workaround reboot hang when booting from SPI */
-        if ((bfin_read_SYSCR() & 0x7) == 0x3)
-                bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
-}
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-void bfin_get_ether_addr(char *addr)
-{
-        random_ether_addr(addr);
-        printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
-}
-EXPORT_SYMBOL(bfin_get_ether_addr);
-#endif
diff --git a/arch/blackfin/mach-bf537/boards/minotaur.c b/arch/blackfin/mach-bf537/boards/minotaur.c
index db7d3a385e4b..3c159819e555 100644
--- a/arch/blackfin/mach-bf537/boards/minotaur.c
+++ b/arch/blackfin/mach-bf537/boards/minotaur.c
@@ -134,9 +134,9 @@ static struct bfin5xx_spi_chip spi_flash_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -156,23 +156,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
-                .modalias = "spi_mmc_dummy",
+                .modalias = "mmc_spi",
                .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = 0,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
-        {
-                .modalias = "spi_mmc",
-                .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf537/boards/pnav10.c b/arch/blackfin/mach-bf537/boards/pnav10.c
index 590eb3a139b7..4e1de1e53f89 100644
--- a/arch/blackfin/mach-bf537/boards/pnav10.c
+++ b/arch/blackfin/mach-bf537/boards/pnav10.c
@@ -289,9 +289,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -364,23 +364,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad9960_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-        {
-                .modalias = "spi_mmc_dummy",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 7,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
        {
-                .modalias = "spi_mmc",
+                .modalias = "mmc_spi",
                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf537/boards/tcm_bf537.c b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
index 3f4f203a06ec..53ad10f3cd76 100644
--- a/arch/blackfin/mach-bf537/boards/tcm_bf537.c
+++ b/arch/blackfin/mach-bf537/boards/tcm_bf537.c
@@ -108,9 +108,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -160,23 +160,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-        {
-                .modalias = "spi_mmc_dummy",
-                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
-                .bus_num = 0,
-                .chip_select = 7,
-                .platform_data = NULL,
-                .controller_data = &spi_mmc_chip_info,
-                .mode = SPI_MODE_3,
-        },
        {
-                .modalias = "spi_mmc",
+                .modalias = "mmc_spi",
                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf537/include/mach/anomaly.h b/arch/blackfin/mach-bf537/include/mach/anomaly.h
index 9cb39121d1cb..1bfd80c26c90 100644
--- a/arch/blackfin/mach-bf537/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf537/include/mach/anomaly.h
@@ -2,7 +2,7 @@
 * File: include/asm-blackfin/mach-bf537/anomaly.h
 * Bugs: Enter bugs at http://blackfin.uclinux.org/
 *
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
 * Licensed under the GPL-2 or later.
 */
@@ -110,7 +110,7 @@
 #define ANOMALY_05000301 (1)
 /* SSYNCs After Writes To CAN/DMA MMR Registers Are Not Always Handled Correctly */
 #define ANOMALY_05000304 (__SILICON_REVISION__ < 3)
-/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */
 #define ANOMALY_05000305 (__SILICON_REVISION__ < 3)
 /* SCKELOW Bit Does Not Maintain State Through Hibernate */
 #define ANOMALY_05000307 (__SILICON_REVISION__ < 3)
@@ -168,9 +168,12 @@
 #define ANOMALY_05000323 (0)
 #define ANOMALY_05000353 (1)
 #define ANOMALY_05000363 (0)
+#define ANOMALY_05000380 (0)
 #define ANOMALY_05000386 (1)
 #define ANOMALY_05000412 (0)
 #define ANOMALY_05000432 (0)
 #define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
 #endif
diff --git a/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
index b3f87e1d16a2..9e34700844a2 100644
--- a/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART0_TX,
        CH_UART0_RX,
 #endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART0_CTS_PIN,
        CONFIG_UART0_RTS_PIN,
 #endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART1_TX,
        CH_UART1_RX,
 #endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART1_CTS_PIN,
        CONFIG_UART1_RTS_PIN,
 #endif
diff --git a/arch/blackfin/mach-bf538/include/mach/anomaly.h b/arch/blackfin/mach-bf538/include/mach/anomaly.h
index e130b4f8a05d..3a5699827363 100644
--- a/arch/blackfin/mach-bf538/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf538/include/mach/anomaly.h
@@ -2,7 +2,7 @@
 * File: include/asm-blackfin/mach-bf538/anomaly.h
 * Bugs: Enter bugs at http://blackfin.uclinux.org/
 *
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
 * Licensed under the GPL-2 or later.
 */
@@ -120,13 +120,17 @@
 #define ANOMALY_05000198 (0)
 #define ANOMALY_05000230 (0)
 #define ANOMALY_05000263 (0)
+#define ANOMALY_05000305 (0)
 #define ANOMALY_05000311 (0)
 #define ANOMALY_05000323 (0)
 #define ANOMALY_05000353 (1)
 #define ANOMALY_05000363 (0)
+#define ANOMALY_05000380 (0)
 #define ANOMALY_05000386 (1)
 #define ANOMALY_05000412 (0)
 #define ANOMALY_05000432 (0)
 #define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
 #endif
diff --git a/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
index 40503b6b89a3..3c2811ebecdd 100644
--- a/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
@@ -144,7 +144,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART0_TX,
        CH_UART0_RX,
 #endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART0_CTS_PIN,
        CONFIG_UART0_RTS_PIN,
 #endif
@@ -158,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART1_TX,
        CH_UART1_RX,
 #endif
-#ifdef CONFIG_BFIN_UART1_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART1_CTS_PIN,
        CONFIG_UART1_RTS_PIN,
 #endif
diff --git a/arch/blackfin/mach-bf548/include/mach/anomaly.h b/arch/blackfin/mach-bf548/include/mach/anomaly.h
index 23d03c52f4b4..882e40ccf0d1 100644
--- a/arch/blackfin/mach-bf548/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf548/include/mach/anomaly.h
@@ -2,12 +2,12 @@
 * File: include/asm-blackfin/mach-bf548/anomaly.h
 * Bugs: Enter bugs at http://blackfin.uclinux.org/
 *
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
 * Licensed under the GPL-2 or later.
 */
 /* This file shoule be up to date with:
- *  - Revision G, 08/07/2008; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List
+ *  - Revision H, 01/16/2009; ADSP-BF542/BF544/BF547/BF548/BF549 Blackfin Processor Anomaly List
 */
 #ifndef _MACH_ANOMALY_H_
@@ -91,8 +91,6 @@
 #define ANOMALY_05000371 (__SILICON_REVISION__ < 2)
 /* USB DP/DM Data Pins May Lose State When Entering Hibernate */
 #define ANOMALY_05000372 (__SILICON_REVISION__ < 1)
-/* Mobile DDR Operation Not Functional */
-#define ANOMALY_05000377 (1)
 /* Security/Authentication Speedpath Causes Authentication To Fail To Initiate */
 #define ANOMALY_05000378 (__SILICON_REVISION__ < 2)
 /* 16-Bit NAND FLASH Boot Mode Is Not Functional */
@@ -157,8 +155,22 @@
 #define ANOMALY_05000429 (__SILICON_REVISION__ < 2)
 /* Software System Reset Corrupts PLL_LOCKCNT Register */
 #define ANOMALY_05000430 (__SILICON_REVISION__ >= 2)
+/* Incorrect Use of Stack in Lockbox Firmware During Authentication */
+#define ANOMALY_05000431 (__SILICON_REVISION__ < 3)
+/* OTP Write Accesses Not Supported */
+#define ANOMALY_05000442 (__SILICON_REVISION__ < 1)
 /* IFLUSH Instruction at End of Hardware Loop Causes Infinite Stall */
 #define ANOMALY_05000443 (1)
+/* CDMAPRIO and L2DMAPRIO Bits in the SYSCR Register Are Not Functional */
+#define ANOMALY_05000446 (1)
+/* UART IrDA Receiver Fails on Extended Bit Pulses */
+#define ANOMALY_05000447 (1)
+/* DDR Clock Duty Cycle Spec Violation (tCH, tCL) */
+#define ANOMALY_05000448 (__SILICON_REVISION__ == 1)
+/* Reduced Timing Margins on DDR Output Setup and Hold (tDS and tDH) */
+#define ANOMALY_05000449 (__SILICON_REVISION__ == 1)
+/* USB DMA Mode 1 Short Packet Data Corruption */
+#define ANOMALY_05000450 (1
 /* Anomalies that don't exist on this proc */
 #define ANOMALY_05000125 (0)
@@ -171,6 +183,8 @@
 #define ANOMALY_05000263 (0)
 #define ANOMALY_05000266 (0)
 #define ANOMALY_05000273 (0)
+#define ANOMALY_05000278 (0)
+#define ANOMALY_05000305 (0)
 #define ANOMALY_05000307 (0)
 #define ANOMALY_05000311 (0)
 #define ANOMALY_05000323 (0)
diff --git a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
index e4cf35e7ab9f..c05e79cba257 100644
--- a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
@@ -63,7 +63,7 @@
 #define UART_ENABLE_INTS(x, v) UART_SET_IER(x, v)
 #define UART_DISABLE_INTS(x) UART_CLEAR_IER(x, 0xF)
-#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS)
+#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART2_CTSRTS)
 # define CONFIG_SERIAL_BFIN_CTSRTS
 # ifndef CONFIG_UART0_CTS_PIN
@@ -74,12 +74,12 @@
 #  define CONFIG_UART0_RTS_PIN -1
 # endif
-# ifndef CONFIG_UART1_CTS_PIN
+# ifndef CONFIG_UART2_CTS_PIN
-#  define CONFIG_UART1_CTS_PIN -1
+#  define CONFIG_UART2_CTS_PIN -1
 # endif
-# ifndef CONFIG_UART1_RTS_PIN
+# ifndef CONFIG_UART2_RTS_PIN
-#  define CONFIG_UART1_RTS_PIN -1
+#  define CONFIG_UART2_RTS_PIN -1
 # endif
 #endif
@@ -130,7 +130,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART0_TX,
        CH_UART0_RX,
 #endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART0_CTS_PIN,
        CONFIG_UART0_RTS_PIN,
 #endif
@@ -144,6 +144,10 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART1_TX,
        CH_UART1_RX,
 #endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+        0,
+        0,
+#endif
        },
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART2
@@ -154,7 +158,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART2_TX,
        CH_UART2_RX,
 #endif
-#ifdef CONFIG_BFIN_UART2_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART2_CTS_PIN,
        CONFIG_UART2_RTS_PIN,
 #endif
@@ -168,6 +172,10 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART3_TX,
        CH_UART3_RX,
 #endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+        0,
+        0,
+#endif
        },
 #endif
 };
diff --git a/arch/blackfin/mach-bf548/include/mach/irq.h b/arch/blackfin/mach-bf548/include/mach/irq.h
index 60299a71e090..f194625f6821 100644
--- a/arch/blackfin/mach-bf548/include/mach/irq.h
+++ b/arch/blackfin/mach-bf548/include/mach/irq.h
@@ -123,8 +123,8 @@ Events         (highest priority)  EMU         0
 #define IRQ_MXVR_ERROR          BFIN_IRQ(51)    /* MXVR Status (Error) Interrupt */
 #define IRQ_MXVR_MSG            BFIN_IRQ(52)    /* MXVR Message Interrupt */
 #define IRQ_MXVR_PKT            BFIN_IRQ(53)    /* MXVR Packet Interrupt */
-#define IRQ_EPP1_ERROR          BFIN_IRQ(54)    /* EPPI1 Error Interrupt */
+#define IRQ_EPPI1_ERROR         BFIN_IRQ(54)    /* EPPI1 Error Interrupt */
-#define IRQ_EPP2_ERROR          BFIN_IRQ(55)    /* EPPI2 Error Interrupt */
+#define IRQ_EPPI2_ERROR         BFIN_IRQ(55)    /* EPPI2 Error Interrupt */
 #define IRQ_UART3_ERROR         BFIN_IRQ(56)    /* UART3 Status (Error) Interrupt */
 #define IRQ_HOST_ERROR          BFIN_IRQ(57)    /* HOST Status (Error) Interrupt */
 #define IRQ_PIXC_ERROR          BFIN_IRQ(59)    /* PIXC Status (Error) Interrupt */
@@ -361,8 +361,8 @@ Events         (highest priority)  EMU         0
 #define IRQ_UART2_ERR           IRQ_UART2_ERROR
 #define IRQ_CAN0_ERR            IRQ_CAN0_ERROR
 #define IRQ_MXVR_ERR            IRQ_MXVR_ERROR
-#define IRQ_EPP1_ERR            IRQ_EPP1_ERROR
+#define IRQ_EPPI1_ERR           IRQ_EPPI1_ERROR
-#define IRQ_EPP2_ERR            IRQ_EPP2_ERROR
+#define IRQ_EPPI2_ERR           IRQ_EPPI2_ERROR
 #define IRQ_UART3_ERR           IRQ_UART3_ERROR
 #define IRQ_HOST_ERR            IRQ_HOST_ERROR
 #define IRQ_PIXC_ERR            IRQ_PIXC_ERROR
diff --git a/arch/blackfin/mach-bf561/boards/Kconfig b/arch/blackfin/mach-bf561/boards/Kconfig
index e41a67b1fb53..e4bc6d7c5a6a 100644
--- a/arch/blackfin/mach-bf561/boards/Kconfig
+++ b/arch/blackfin/mach-bf561/boards/Kconfig
@@ -19,9 +19,4 @@ config BFIN561_BLUETECHNIX_CM
        help
          CM-BF561 support for EVAL- and DEV-Board.
-config GENERIC_BF561_BOARD
-        bool "Generic"
-        help
-          Generic or Custom board support.
 endchoice
diff --git a/arch/blackfin/mach-bf561/boards/Makefile b/arch/blackfin/mach-bf561/boards/Makefile
index 04add010b568..3a152559e957 100644
--- a/arch/blackfin/mach-bf561/boards/Makefile
+++ b/arch/blackfin/mach-bf561/boards/Makefile
@@ -2,7 +2,6 @@
 # arch/blackfin/mach-bf561/boards/Makefile
 #
-obj-$(CONFIG_GENERIC_BF561_BOARD)      += generic_board.o
 obj-$(CONFIG_BFIN561_BLUETECHNIX_CM)   += cm_bf561.o
 obj-$(CONFIG_BFIN561_EZKIT)            += ezkit.o
 obj-$(CONFIG_BFIN561_TEPLA)            += tepla.o
diff --git a/arch/blackfin/mach-bf561/boards/cm_bf561.c b/arch/blackfin/mach-bf561/boards/cm_bf561.c
index 6880d1ebfe60..f623c6b0719f 100644
--- a/arch/blackfin/mach-bf561/boards/cm_bf561.c
+++ b/arch/blackfin/mach-bf561/boards/cm_bf561.c
@@ -105,9 +105,9 @@ static struct bfin5xx_spi_chip ad9960_spi_chip_info = {
 };
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip spi_mmc_chip_info = {
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
-        .enable_dma = 1,
+        .enable_dma = 0,
        .bits_per_word = 8,
 };
 #endif
@@ -155,14 +155,13 @@ static struct spi_board_info bfin_spi_board_info[] __initdata = {
                .controller_data = &ad9960_spi_chip_info,
        },
 #endif
-#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE)
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
        {
-                .modalias = "spi_mmc",
+                .modalias = "mmc_spi",
                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
                .bus_num = 0,
-                .chip_select = CONFIG_SPI_MMC_CS_CHAN,
+                .chip_select = 5,
-                .platform_data = NULL,
+                .controller_data = &mmc_spi_chip_info,
-                .controller_data = &spi_mmc_chip_info,
                .mode = SPI_MODE_3,
        },
 #endif
diff --git a/arch/blackfin/mach-bf561/boards/generic_board.c b/arch/blackfin/mach-bf561/boards/generic_board.c
deleted file mode 100644
index 0ba366a0e696..000000000000
--- a/arch/blackfin/mach-bf561/boards/generic_board.c
+++ /dev/null
@@ -1,113 +0,0 @@
-/*
- * File:         arch/blackfin/mach-bf561/generic_board.c
- * Based on:     arch/blackfin/mach-bf533/ezkit.c
- * Author:       Aidan Williams <aidan@nicta.com.au>
- *
- * Created:
- * Description:
- *
- * Modified:
- *               Copyright 2005 National ICT Australia (NICTA)
- *               Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs:         Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
- */
-#include <linux/device.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-const char bfin_board_name[] = "UNKNOWN BOARD";
-/*
- *  Driver needs to know address, irq and flag pin.
- */
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-static struct resource smc91x_resources[] = {
-        {
-                .start = 0x2C010300,
-                .end = 0x2C010300 + 16,
-                .flags = IORESOURCE_MEM,
-        }, {
-                .start = IRQ_PROG_INTB,
-                .end = IRQ_PROG_INTB,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        }, {
-                .start = IRQ_PF9,
-                .end = IRQ_PF9,
-                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
-        },
-};
-static struct platform_device smc91x_device = {
-        .name = "smc91x",
-        .id = 0,
-        .num_resources = ARRAY_SIZE(smc91x_resources),
-        .resource = smc91x_resources,
-};
-#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
-        {
-                .start = 0xFFC00400,
-                .end = 0xFFC004FF,
-                .flags = IORESOURCE_MEM,
-        },
-        {
-                .start = IRQ_UART0_RX,
-                .end = IRQ_UART0_RX+1,
-                .flags = IORESOURCE_IRQ,
-        },
-        {
-                .start = CH_UART0_RX,
-                .end = CH_UART0_RX+1,
-                .flags = IORESOURCE_DMA,
-        },
-};
-static struct platform_device bfin_sir0_device = {
-        .name = "bfin_sir",
-        .id = 0,
-        .num_resources = ARRAY_SIZE(bfin_sir0_resources),
-        .resource = bfin_sir0_resources,
-};
-#endif
-#endif
-static struct platform_device *generic_board_devices[] __initdata = {
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-        &smc91x_device,
-#endif
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-        &bfin_sir0_device,
-#endif
-#endif
-};
-static int __init generic_board_init(void)
-{
-        printk(KERN_INFO "%s(): registering device resources\n", __func__);
-        return platform_add_devices(generic_board_devices,
-                                    ARRAY_SIZE(generic_board_devices));
-}
-arch_initcall(generic_board_init);
diff --git a/arch/blackfin/mach-bf561/include/mach/anomaly.h b/arch/blackfin/mach-bf561/include/mach/anomaly.h
index 1a9e17562821..d0b0b3506440 100644
--- a/arch/blackfin/mach-bf561/include/mach/anomaly.h
+++ b/arch/blackfin/mach-bf561/include/mach/anomaly.h
@@ -2,7 +2,7 @@
 * File: include/asm-blackfin/mach-bf561/anomaly.h
 * Bugs: Enter bugs at http://blackfin.uclinux.org/
 *
- * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Copyright (C) 2004-2009 Analog Devices Inc.
 * Licensed under the GPL-2 or later.
 */
@@ -224,7 +224,7 @@
 #define ANOMALY_05000301 (1)
 /* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
 #define ANOMALY_05000302 (1)
-/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+/* SPORT_HYS Bit in PLL_CTL Register Is Not Functional */
 #define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
 /* SCKELOW Bit Does Not Maintain State Through Hibernate */
 #define ANOMALY_05000307 (__SILICON_REVISION__ < 5)
@@ -283,8 +283,11 @@
 #define ANOMALY_05000273 (0)
 #define ANOMALY_05000311 (0)
 #define ANOMALY_05000353 (1)
+#define ANOMALY_05000380 (0)
 #define ANOMALY_05000386 (1)
 #define ANOMALY_05000432 (0)
 #define ANOMALY_05000435 (0)
+#define ANOMALY_05000447 (0)
+#define ANOMALY_05000448 (0)
 #endif
diff --git a/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
index 043bfcf26c52..ca8c5f645209 100644
--- a/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
@@ -134,7 +134,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
        CH_UART_TX,
        CH_UART_RX,
 #endif
-#ifdef CONFIG_BFIN_UART0_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
        CONFIG_UART0_CTS_PIN,
        CONFIG_UART0_RTS_PIN,
 #endif
diff --git a/arch/blackfin/mach-common/arch_checks.c b/arch/blackfin/mach-common/arch_checks.c
index 98133b968f7b..80d39b2f9db2 100644
--- a/arch/blackfin/mach-common/arch_checks.c
+++ b/arch/blackfin/mach-common/arch_checks.c
@@ -62,3 +62,12 @@
 #if (CONFIG_BOOT_LOAD & 0x3)
 # error "The kernel load address must be 4 byte aligned"
 #endif
+/* The entire kernel must be able to make a 24bit pcrel call to start of L1 */
+#if ((0xffffffff - L1_CODE_START + 1) + CONFIG_BOOT_LOAD) > 0x1000000
+# error "The kernel load address is too high; keep it below 10meg for safety"
+#endif
+#if ANOMALY_05000448
+# error You are using a part with anomaly 05000448, this issue causes random memory read/write failures - that means random crashes.
+#endif
diff --git a/arch/blackfin/mach-common/cache.S b/arch/blackfin/mach-common/cache.S
index 3c98dacbf289..aa0648c6a9fe 100644
--- a/arch/blackfin/mach-common/cache.S
+++ b/arch/blackfin/mach-common/cache.S
@@ -66,11 +66,33 @@
 /* Invalidate all instruction cache lines assocoiated with this memory area */
 ENTRY(_blackfin_icache_flush_range)
+/*
+ * Walkaround to avoid loading wrong instruction after invalidating icache
+ * and following sequence is met.
+ *
+ * 1) One instruction address is cached in the instruction cache.
+ * 2) This instruction in SDRAM is changed.
+ * 3) IFLASH[P0] is executed only once in blackfin_icache_flush_range().
+ * 4) This instruction is executed again, but the old one is loaded.
+ */
+        P0 = R0;
+        IFLUSH[P0];
        do_flush IFLUSH, , nop
 ENDPROC(_blackfin_icache_flush_range)
 /* Flush all cache lines assocoiated with this area of memory. */
 ENTRY(_blackfin_icache_dcache_flush_range)
+/*
+ * Walkaround to avoid loading wrong instruction after invalidating icache
+ * and following sequence is met.
+ *
+ * 1) One instruction address is cached in the instruction cache.
+ * 2) This instruction in SDRAM is changed.
+ * 3) IFLASH[P0] is executed only once in blackfin_icache_flush_range().
+ * 4) This instruction is executed again, but the old one is loaded.
+ */
+        P0 = R0;
+        IFLUSH[P0];
        do_flush FLUSH, IFLUSH
 ENDPROC(_blackfin_icache_dcache_flush_range)
diff --git a/arch/blackfin/mach-common/clocks-init.c b/arch/blackfin/mach-common/clocks-init.c
index 9dddb6f8cc85..35393651359b 100644
--- a/arch/blackfin/mach-common/clocks-init.c
+++ b/arch/blackfin/mach-common/clocks-init.c
@@ -17,7 +17,7 @@
 #define SDGCTL_WIDTH (1 << 31)  /* SDRAM external data path width */
 #define PLL_CTL_VAL \
        (((CONFIG_VCO_MULT & 63) << 9) | CLKIN_HALF | \
-         (PLL_BYPASS << 8) | (ANOMALY_05000265 ? 0x8000 : 0))
+         (PLL_BYPASS << 8) | (ANOMALY_05000305 ? 0 : 0x8000))
 __attribute__((l1_text))
 static void do_sync(void)
diff --git a/arch/blackfin/mach-common/dpmc_modes.S b/arch/blackfin/mach-common/dpmc_modes.S
index 4da50bcd9300..8009a512fb11 100644
--- a/arch/blackfin/mach-common/dpmc_modes.S
+++ b/arch/blackfin/mach-common/dpmc_modes.S
@@ -376,10 +376,22 @@ ENTRY(_do_hibernate)
 #endif
 #ifdef PINT0_ASSIGN
+        PM_SYS_PUSH(PINT0_MASK_SET)
+        PM_SYS_PUSH(PINT1_MASK_SET)
+        PM_SYS_PUSH(PINT2_MASK_SET)
+        PM_SYS_PUSH(PINT3_MASK_SET)
        PM_SYS_PUSH(PINT0_ASSIGN)
        PM_SYS_PUSH(PINT1_ASSIGN)
        PM_SYS_PUSH(PINT2_ASSIGN)
        PM_SYS_PUSH(PINT3_ASSIGN)
+        PM_SYS_PUSH(PINT0_INVERT_SET)
+        PM_SYS_PUSH(PINT1_INVERT_SET)
+        PM_SYS_PUSH(PINT2_INVERT_SET)
+        PM_SYS_PUSH(PINT3_INVERT_SET)
+        PM_SYS_PUSH(PINT0_EDGE_SET)
+        PM_SYS_PUSH(PINT1_EDGE_SET)
+        PM_SYS_PUSH(PINT2_EDGE_SET)
+        PM_SYS_PUSH(PINT3_EDGE_SET)
 #endif
        PM_SYS_PUSH(EBIU_AMBCTL0)
@@ -714,10 +726,22 @@ ENTRY(_do_hibernate)
        PM_SYS_POP(EBIU_AMBCTL0)
 #ifdef PINT0_ASSIGN
+        PM_SYS_POP(PINT3_EDGE_SET)
+        PM_SYS_POP(PINT2_EDGE_SET)
+        PM_SYS_POP(PINT1_EDGE_SET)
+        PM_SYS_POP(PINT0_EDGE_SET)
+        PM_SYS_POP(PINT3_INVERT_SET)
+        PM_SYS_POP(PINT2_INVERT_SET)
+        PM_SYS_POP(PINT1_INVERT_SET)
+        PM_SYS_POP(PINT0_INVERT_SET)
        PM_SYS_POP(PINT3_ASSIGN)
        PM_SYS_POP(PINT2_ASSIGN)
        PM_SYS_POP(PINT1_ASSIGN)
        PM_SYS_POP(PINT0_ASSIGN)
+        PM_SYS_POP(PINT3_MASK_SET)
+        PM_SYS_POP(PINT2_MASK_SET)
+        PM_SYS_POP(PINT1_MASK_SET)
+        PM_SYS_POP(PINT0_MASK_SET)
 #endif
 #ifdef SICA_IWR1
diff --git a/arch/blackfin/mach-common/entry.S b/arch/blackfin/mach-common/entry.S
index 88de053bbe8e..21e65a339a22 100644
--- a/arch/blackfin/mach-common/entry.S
+++ b/arch/blackfin/mach-common/entry.S
@@ -600,6 +600,19 @@ ENTRY(_system_call)
        p2 = [p2];
        [p2+(TASK_THREAD+THREAD_KSP)] = sp;
+#ifdef CONFIG_IPIPE
+        r0 = sp;
+        SP += -12;
+        call ___ipipe_syscall_root;
+        SP += 12;
+        cc = r0 == 1;
+        if cc jump .Lsyscall_really_exit;
+        cc = r0 == -1;
+        if cc jump .Lresume_userspace;
+        r3 = [sp + PT_R3];
+        r4 = [sp + PT_R4];
+        p0 = [sp + PT_ORIG_P0];
+#endif /* CONFIG_IPIPE */
        /* Check the System Call */
        r7 = __NR_syscall;
@@ -654,6 +667,17 @@ ENTRY(_system_call)
        r7 =  r7 & r4;
 .Lsyscall_resched:
+#ifdef CONFIG_IPIPE
+        cc = BITTST(r7, TIF_IRQ_SYNC);
+        if !cc jump .Lsyscall_no_irqsync;
+        [--sp] = reti;
+        r0 = [sp++];
+        SP += -12;
+        call ___ipipe_sync_root;
+        SP += 12;
+        jump .Lresume_userspace_1;
+.Lsyscall_no_irqsync:
+#endif
        cc = BITTST(r7, TIF_NEED_RESCHED);
        if !cc jump .Lsyscall_sigpending;
@@ -685,6 +709,10 @@ ENTRY(_system_call)
 .Lsyscall_really_exit:
        r5 = [sp + PT_RESERVED];
        rets = r5;
+#ifdef CONFIG_IPIPE
+        [--sp] = reti;
+        r5 = [sp++];
+#endif /* CONFIG_IPIPE */
        rts;
 ENDPROC(_system_call)
@@ -771,6 +799,15 @@ _new_old_task:
 ENDPROC(_resume)
 ENTRY(_ret_from_exception)
+#ifdef CONFIG_IPIPE
+        [--sp] = rets;
+        SP += -12;
+        call ___ipipe_check_root
+        SP += 12
+        rets = [sp++];
+        cc = r0 == 0;
+        if cc jump 4f;                /* not on behalf of Linux, get out */
+#endif /* CONFIG_IPIPE */
        p2.l = lo(IPEND);
        p2.h = hi(IPEND);
@@ -827,6 +864,28 @@ ENTRY(_ret_from_exception)
        rts;
 ENDPROC(_ret_from_exception)
+#ifdef CONFIG_IPIPE
+_sync_root_irqs:
+        [--sp] = reti;          /* Reenable interrupts */
+        r0 = [sp++];
+        jump.l ___ipipe_sync_root
+_resume_kernel_from_int:
+        r0.l = _sync_root_irqs
+        r0.h = _sync_root_irqs
+        [--sp] = rets;
+        [--sp] = ( r7:4, p5:3 );
+        SP += -12;
+        call ___ipipe_call_irqtail
+        SP += 12;
+        ( r7:4, p5:3 ) = [sp++];
+        rets = [sp++];
+        rts
+#else
+#define _resume_kernel_from_int  2f
+#endif
 ENTRY(_return_from_int)
        /* If someone else already raised IRQ 15, do nothing.  */
        csync;
@@ -848,7 +907,7 @@ ENTRY(_return_from_int)
        r1 = r0 - r1;
        r2 = r0 & r1;
        cc = r2 == 0;
-        if !cc jump 2f;
+        if !cc jump _resume_kernel_from_int;
        /* Lower the interrupt level to 15.  */
        p0.l = lo(EVT15);
diff --git a/arch/blackfin/mach-common/interrupt.S b/arch/blackfin/mach-common/interrupt.S
index 43c4eb9acb65..0069c2dd4625 100644
--- a/arch/blackfin/mach-common/interrupt.S
+++ b/arch/blackfin/mach-common/interrupt.S
@@ -235,6 +235,7 @@ ENDPROC(_evt_system_call)
 #ifdef CONFIG_IPIPE
 ENTRY(___ipipe_call_irqtail)
+        p0 = r0;
        r0.l = 1f;
        r0.h = 1f;
        reti = r0;
@@ -242,9 +243,6 @@ ENTRY(___ipipe_call_irqtail)
 1:
        [--sp] = rets;
        [--sp] = ( r7:4, p5:3 );
-        p0.l = ___ipipe_irq_tail_hook;
-        p0.h = ___ipipe_irq_tail_hook;
-        p0 = [p0];
        sp += -12;
        call (p0);
        sp += 12;
@@ -259,7 +257,7 @@ ENTRY(___ipipe_call_irqtail)
        p0.h = hi(EVT14);
        [p0] = r0;
        csync;
-        r0 = 0x401f;
+        r0 = 0x401f (z);
        sti r0;
        raise 14;
        [--sp] = reti;          /* IRQs on. */
@@ -277,11 +275,7 @@ ENTRY(___ipipe_call_irqtail)
        p0.h = _bfin_irq_flags;
        r0 = [p0];
        sti r0;
-#if 0 /* FIXME: this actually raises scheduling latencies */
-        /* Reenable interrupts */
-        [--sp] = reti;
-        r0 = [sp++];
-#endif
        rts;
 ENDPROC(___ipipe_call_irqtail)
 #endif /* CONFIG_IPIPE */
diff --git a/arch/blackfin/mach-common/ints-priority.c b/arch/blackfin/mach-common/ints-priority.c
index 202494568c6c..a7d7b2dd4059 100644
--- a/arch/blackfin/mach-common/ints-priority.c
+++ b/arch/blackfin/mach-common/ints-priority.c
@@ -161,11 +161,15 @@ static void bfin_core_unmask_irq(unsigned int irq)
 static void bfin_internal_mask_irq(unsigned int irq)
 {
+        unsigned long flags;
 #ifdef CONFIG_BF53x
+        local_irq_save_hw(flags);
        bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() &
                             ~(1 << SIC_SYSIRQ(irq)));
 #else
        unsigned mask_bank, mask_bit;
+        local_irq_save_hw(flags);
        mask_bank = SIC_SYSIRQ(irq) / 32;
        mask_bit = SIC_SYSIRQ(irq) % 32;
        bfin_write_SIC_IMASK(mask_bank, bfin_read_SIC_IMASK(mask_bank) &
@@ -175,15 +179,20 @@ static void bfin_internal_mask_irq(unsigned int irq)
                             ~(1 << mask_bit));
 #endif
 #endif
+        local_irq_restore_hw(flags);
 }
 static void bfin_internal_unmask_irq(unsigned int irq)
 {
+        unsigned long flags;
 #ifdef CONFIG_BF53x
+        local_irq_save_hw(flags);
        bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() |
                             (1 << SIC_SYSIRQ(irq)));
 #else
        unsigned mask_bank, mask_bit;
+        local_irq_save_hw(flags);
        mask_bank = SIC_SYSIRQ(irq) / 32;
        mask_bit = SIC_SYSIRQ(irq) % 32;
        bfin_write_SIC_IMASK(mask_bank, bfin_read_SIC_IMASK(mask_bank) |
@@ -193,6 +202,7 @@ static void bfin_internal_unmask_irq(unsigned int irq)
                             (1 << mask_bit));
 #endif
 #endif
+        local_irq_restore_hw(flags);
 }
 #ifdef CONFIG_PM
@@ -390,7 +400,7 @@ static void bfin_demux_error_irq(unsigned int int_err_irq,
 static inline void bfin_set_irq_handler(unsigned irq, irq_flow_handler_t handle)
 {
 #ifdef CONFIG_IPIPE
-        _set_irq_handler(irq, handle_edge_irq);
+        _set_irq_handler(irq, handle_level_irq);
 #else
        struct irq_desc *desc = irq_desc + irq;
        /* May not call generic set_irq_handler() due to spinlock
@@ -1055,13 +1065,18 @@ int __init init_arch_irq(void)
 #endif
                default:
 #ifdef CONFIG_IPIPE
-        /*
+                        /*
-         * We want internal interrupt sources to be masked, because
+                         * We want internal interrupt sources to be
-         * ISRs may trigger interrupts recursively (e.g. DMA), but
+                         * masked, because ISRs may trigger interrupts
-         * interrupts are _not_ masked at CPU level. So let's handle
+                         * recursively (e.g. DMA), but interrupts are
-         * them as level interrupts.
+                         * _not_ masked at CPU level. So let's handle
-         */
+                         * most of them as level interrupts, except
-                        set_irq_handler(irq, handle_level_irq);
+                         * the timer interrupt which is special.
+                         */
+                        if (irq == IRQ_SYSTMR || irq == IRQ_CORETMR)
+                                set_irq_handler(irq, handle_simple_irq);
+                        else
+                                set_irq_handler(irq, handle_level_irq);
 #else /* !CONFIG_IPIPE */
                        set_irq_handler(irq, handle_simple_irq);
 #endif /* !CONFIG_IPIPE */
@@ -1123,9 +1138,8 @@ int __init init_arch_irq(void)
 #ifdef CONFIG_IPIPE
        for (irq = 0; irq < NR_IRQS; irq++) {
-                struct irq_desc *desc = irq_desc + irq;
+                struct irq_desc *desc = irq_to_desc(irq);
                desc->ic_prio = __ipipe_get_irq_priority(irq);
-                desc->thr_prio = __ipipe_get_irqthread_priority(irq);
        }
 #endif /* CONFIG_IPIPE */
@@ -1208,76 +1222,21 @@ int __ipipe_get_irq_priority(unsigned irq)
        return IVG15;
 }
-int __ipipe_get_irqthread_priority(unsigned irq)
-{
-        int ient, prio;
-        int demux_irq;
-        /* The returned priority value is rescaled to [0..IVG13+1]
-         * with 0 being the lowest effective priority level. */
-        if (irq <= IRQ_CORETMR)
-                return IVG13 - irq + 1;
-        /* GPIO IRQs are given the priority of the demux
-         * interrupt. */
-        if (IS_GPIOIRQ(irq)) {
-#if defined(CONFIG_BF54x)
-                u32 bank = PINT_2_BANK(irq2pint_lut[irq - SYS_IRQS]);
-                demux_irq = (bank == 0 ? IRQ_PINT0 :
-                                bank == 1 ? IRQ_PINT1 :
-                                bank == 2 ? IRQ_PINT2 :
-                                IRQ_PINT3);
-#elif defined(CONFIG_BF561)
-                demux_irq = (irq >= IRQ_PF32 ? IRQ_PROG2_INTA :
-                                irq >= IRQ_PF16 ? IRQ_PROG1_INTA :
-                                IRQ_PROG0_INTA);
-#elif defined(CONFIG_BF52x)
-                demux_irq = (irq >= IRQ_PH0 ? IRQ_PORTH_INTA :
-                                irq >= IRQ_PG0 ? IRQ_PORTG_INTA :
-                                IRQ_PORTF_INTA);
-#else
-                demux_irq = irq;
-#endif
-                return IVG13 - PRIO_GPIODEMUX(demux_irq) + 1;
-        }
-        /* The GPIO demux interrupt is given a lower priority
-         * than the GPIO IRQs, so that its threaded handler
-         * unmasks the interrupt line after the decoded IRQs
-         * have been processed. */
-        prio = PRIO_GPIODEMUX(irq);
-        /* demux irq? */
-        if (prio != -1)
-                return IVG13 - prio;
-        for (ient = 0; ient < NR_PERI_INTS; ient++) {
-                struct ivgx *ivg = ivg_table + ient;
-                if (ivg->irqno == irq) {
-                        for (prio = 0; prio <= IVG13-IVG7; prio++) {
-                                if (ivg7_13[prio].ifirst <= ivg &&
-                                    ivg7_13[prio].istop > ivg)
-                                        return IVG7 - prio;
-                        }
-                }
-        }
-        return 0;
-}
 /* Hw interrupts are disabled on entry (check SAVE_CONTEXT). */
 #ifdef CONFIG_DO_IRQ_L1
 __attribute__((l1_text))
 #endif
 asmlinkage int __ipipe_grab_irq(int vec, struct pt_regs *regs)
 {
+        struct ipipe_percpu_domain_data *p = ipipe_root_cpudom_ptr();
+        struct ipipe_domain *this_domain = ipipe_current_domain;
        struct ivgx *ivg_stop = ivg7_13[vec-IVG7].istop;
        struct ivgx *ivg = ivg7_13[vec-IVG7].ifirst;
-        int irq;
+        int irq, s;
        if (likely(vec == EVT_IVTMR_P)) {
                irq = IRQ_CORETMR;
-                goto handle_irq;
+                goto core_tick;
        }
        SSYNC();
@@ -1319,24 +1278,39 @@ asmlinkage int __ipipe_grab_irq(int vec, struct pt_regs *regs)
        irq = ivg->irqno;
        if (irq == IRQ_SYSTMR) {
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+core_tick:
+#else
                bfin_write_TIMER_STATUS(1); /* Latch TIMIL0 */
+#endif
                /* This is basically what we need from the register frame. */
                __raw_get_cpu_var(__ipipe_tick_regs).ipend = regs->ipend;
                __raw_get_cpu_var(__ipipe_tick_regs).pc = regs->pc;
-                if (!ipipe_root_domain_p)
+                if (this_domain != ipipe_root_domain)
-                        __raw_get_cpu_var(__ipipe_tick_regs).ipend |= 0x10;
-                else
                        __raw_get_cpu_var(__ipipe_tick_regs).ipend &= ~0x10;
+                else
+                        __raw_get_cpu_var(__ipipe_tick_regs).ipend |= 0x10;
        }
-handle_irq:
+#ifndef CONFIG_GENERIC_CLOCKEVENTS
+core_tick:
+#endif
+        if (this_domain == ipipe_root_domain) {
+                s = __test_and_set_bit(IPIPE_SYNCDEFER_FLAG, &p->status);
+                barrier();
+        }
        ipipe_trace_irq_entry(irq);
        __ipipe_handle_irq(irq, regs);
-       ipipe_trace_irq_exit(irq);
+        ipipe_trace_irq_exit(irq);
-       if (ipipe_root_domain_p)
+        if (this_domain == ipipe_root_domain) {
-                return !test_bit(IPIPE_STALL_FLAG, &ipipe_root_cpudom_var(status));
+                set_thread_flag(TIF_IRQ_SYNC);
+                if (!s) {
+                        __clear_bit(IPIPE_SYNCDEFER_FLAG, &p->status);
+                        return !test_bit(IPIPE_STALL_FLAG, &p->status);
+                }
+        }
       return 0;
 }
diff --git a/arch/blackfin/mach-common/smp.c b/arch/blackfin/mach-common/smp.c
index 77c992847094..93eab6146079 100644
--- a/arch/blackfin/mach-common/smp.c
+++ b/arch/blackfin/mach-common/smp.c
@@ -158,10 +158,14 @@ static irqreturn_t ipi_handler(int irq, void *dev_instance)
                        kfree(msg);
                        break;
                case BFIN_IPI_CALL_FUNC:
+                        spin_unlock(&msg_queue->lock);
                        ipi_call_function(cpu, msg);
+                        spin_lock(&msg_queue->lock);
                        break;
                case BFIN_IPI_CPU_STOP:
+                        spin_unlock(&msg_queue->lock);
                        ipi_cpu_stop(cpu);
+                        spin_lock(&msg_queue->lock);
                        kfree(msg);
                        break;
                default:
@@ -457,7 +461,7 @@ void smp_icache_flush_range_others(unsigned long start, unsigned long end)
        smp_flush_data.start = start;
        smp_flush_data.end = end;
-        if (smp_call_function(&ipi_flush_icache, &smp_flush_data, 1))
+        if (smp_call_function(&ipi_flush_icache, &smp_flush_data, 0))
                printk(KERN_WARNING "SMP: failed to run I-cache flush request on other CPUs\n");
 }
 EXPORT_SYMBOL_GPL(smp_icache_flush_range_others);
diff --git a/arch/blackfin/mm/init.c b/arch/blackfin/mm/init.c
index d0532b72bba5..9c3629b9a689 100644
--- a/arch/blackfin/mm/init.c
+++ b/arch/blackfin/mm/init.c
@@ -104,7 +104,7 @@ void __init paging_init(void)
        }
 }
-asmlinkage void init_pda(void)
+asmlinkage void __init init_pda(void)
 {
        unsigned int cpu = raw_smp_processor_id();
diff --git a/arch/ia64/sn/pci/pcibr/pcibr_dma.c b/arch/ia64/sn/pci/pcibr/pcibr_dma.c
index e626e50a938a..060df4aa9916 100644
--- a/arch/ia64/sn/pci/pcibr/pcibr_dma.c
+++ b/arch/ia64/sn/pci/pcibr/pcibr_dma.c
@@ -135,11 +135,10 @@ pcibr_dmatrans_direct64(struct pcidev_info * info, u64 paddr,
        if (SN_DMA_ADDRTYPE(dma_flags) == SN_DMA_ADDR_PHYS)
                pci_addr = IS_PIC_SOFT(pcibus_info) ?
                                PHYS_TO_DMA(paddr) :
-                                PHYS_TO_TIODMA(paddr) | dma_attributes;
+                                PHYS_TO_TIODMA(paddr);
        else
-                pci_addr = IS_PIC_SOFT(pcibus_info) ?
+                pci_addr = paddr;
-                                paddr :
+        pci_addr |= dma_attributes;
-                                paddr | dma_attributes;
        /* Handle Bus mode */
        if (IS_PCIX(pcibus_info))
diff --git a/arch/mips/include/asm/compat.h b/arch/mips/include/asm/compat.h
index ac5d541368e9..6c5b40905dd6 100644
--- a/arch/mips/include/asm/compat.h
+++ b/arch/mips/include/asm/compat.h
@@ -3,6 +3,8 @@
 /*
 * Architecture specific compatibility types
 */
+#include <linux/seccomp.h>
+#include <linux/thread_info.h>
 #include <linux/types.h>
 #include <asm/page.h>
 #include <asm/ptrace.h>
@@ -218,4 +220,9 @@ struct compat_shmid64_ds {
        compat_ulong_t  __unused2;
 };
+static inline int is_compat_task(void)
+{
+        return test_thread_flag(TIF_32BIT);
+}
 #endif /* _ASM_COMPAT_H */
diff --git a/arch/x86/kernel/ds.c b/arch/x86/kernel/ds.c
index 169a120587be..87b67e3a765a 100644
--- a/arch/x86/kernel/ds.c
+++ b/arch/x86/kernel/ds.c
@@ -729,7 +729,7 @@ struct pebs_tracer *ds_request_pebs(struct task_struct *task,
        spin_unlock_irqrestore(&ds_lock, irq);
-        ds_write_config(tracer->ds.context, &tracer->trace.ds, ds_bts);
+        ds_write_config(tracer->ds.context, &tracer->trace.ds, ds_pebs);
        ds_resume_pebs(tracer);
        return tracer;
@@ -1029,5 +1029,4 @@ void ds_copy_thread(struct task_struct *tsk, struct task_struct *father)
 void ds_exit_thread(struct task_struct *tsk)
 {
-        WARN_ON(tsk->thread.ds_ctx);
 }
diff --git a/block/blk-merge.c b/block/blk-merge.c
index a104593e70c3..5a244f05360f 100644
--- a/block/blk-merge.c
+++ b/block/blk-merge.c
@@ -39,14 +39,13 @@ void blk_recalc_rq_sectors(struct request *rq, int nsect)
 }
 static unsigned int __blk_recalc_rq_segments(struct request_queue *q,
-                                             struct bio *bio,
+                                             struct bio *bio)
-                                             unsigned int *seg_size_ptr)
 {
        unsigned int phys_size;
        struct bio_vec *bv, *bvprv = NULL;
        int cluster, i, high, highprv = 1;
        unsigned int seg_size, nr_phys_segs;
-        struct bio *fbio;
+        struct bio *fbio, *bbio;
        if (!bio)
                return 0;
@@ -87,26 +86,20 @@ new_segment:
                        seg_size = bv->bv_len;
                        highprv = high;
                }
+                bbio = bio;
        }
-        if (seg_size_ptr)
+        if (nr_phys_segs == 1 && seg_size > fbio->bi_seg_front_size)
-                *seg_size_ptr = seg_size;
+                fbio->bi_seg_front_size = seg_size;
+        if (seg_size > bbio->bi_seg_back_size)
+                bbio->bi_seg_back_size = seg_size;
        return nr_phys_segs;
 }
 void blk_recalc_rq_segments(struct request *rq)
 {
-        unsigned int seg_size = 0, phys_segs;
+        rq->nr_phys_segments = __blk_recalc_rq_segments(rq->q, rq->bio);
-        phys_segs = __blk_recalc_rq_segments(rq->q, rq->bio, &seg_size);
-        if (phys_segs == 1 && seg_size > rq->bio->bi_seg_front_size)
-                rq->bio->bi_seg_front_size = seg_size;
-        if (seg_size > rq->biotail->bi_seg_back_size)
-                rq->biotail->bi_seg_back_size = seg_size;
-        rq->nr_phys_segments = phys_segs;
 }
 void blk_recount_segments(struct request_queue *q, struct bio *bio)
@@ -114,7 +107,7 @@ void blk_recount_segments(struct request_queue *q, struct bio *bio)
        struct bio *nxt = bio->bi_next;
        bio->bi_next = NULL;
-        bio->bi_phys_segments = __blk_recalc_rq_segments(q, bio, NULL);
+        bio->bi_phys_segments = __blk_recalc_rq_segments(q, bio);
        bio->bi_next = nxt;
        bio->bi_flags |= (1 << BIO_SEG_VALID);
 }
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index a603bbf9b1b7..66e012cd3271 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -582,18 +582,18 @@ static const struct pci_device_id ahci_pci_tbl[] = {
        { PCI_VDEVICE(NVIDIA, 0x0abd), board_ahci },            /* MCP79 */
        { PCI_VDEVICE(NVIDIA, 0x0abe), board_ahci },            /* MCP79 */
        { PCI_VDEVICE(NVIDIA, 0x0abf), board_ahci },            /* MCP79 */
-        { PCI_VDEVICE(NVIDIA, 0x0bc8), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d84), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bc9), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d85), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bca), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d86), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bcb), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d87), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bcc), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d88), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bcd), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d89), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bce), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d8a), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bcf), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d8b), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bc4), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d8c), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bc5), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d8d), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bc6), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d8e), board_ahci },            /* MCP89 */
-        { PCI_VDEVICE(NVIDIA, 0x0bc7), board_ahci },            /* MCP7B */
+        { PCI_VDEVICE(NVIDIA, 0x0d8f), board_ahci },            /* MCP89 */
        /* SiS */
        { PCI_VDEVICE(SI, 0x1184), board_ahci },                /* SiS 966 */
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 9fbf0595f3d4..060bcd601f57 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -1322,14 +1322,16 @@ static u64 ata_id_n_sectors(const u16 *id)
 {
        if (ata_id_has_lba(id)) {
                if (ata_id_has_lba48(id))
-                        return ata_id_u64(id, 100);
+                        return ata_id_u64(id, ATA_ID_LBA_CAPACITY_2);
                else
-                        return ata_id_u32(id, 60);
+                        return ata_id_u32(id, ATA_ID_LBA_CAPACITY);
        } else {
                if (ata_id_current_chs_valid(id))
-                        return ata_id_u32(id, 57);
+                        return id[ATA_ID_CUR_CYLS] * id[ATA_ID_CUR_HEADS] *
+                               id[ATA_ID_CUR_SECTORS];
                else
-                        return id[1] * id[3] * id[6];
+                        return id[ATA_ID_CYLS] * id[ATA_ID_HEADS] *
+                               id[ATA_ID_SECTORS];
        }
 }
@@ -4612,7 +4614,7 @@ void ata_sg_clean(struct ata_queued_cmd *qc)
        VPRINTK("unmapping %u sg elements\n", qc->n_elem);
        if (qc->n_elem)
-                dma_unmap_sg(ap->dev, sg, qc->n_elem, dir);
+                dma_unmap_sg(ap->dev, sg, qc->orig_n_elem, dir);
        qc->flags &= ~ATA_QCFLAG_DMAMAP;
        qc->sg = NULL;
@@ -4727,7 +4729,7 @@ static int ata_sg_setup(struct ata_queued_cmd *qc)
                return -1;
        DPRINTK("%d sg elements mapped\n", n_elem);
+        qc->orig_n_elem = qc->n_elem;
        qc->n_elem = n_elem;
        qc->flags |= ATA_QCFLAG_DMAMAP;
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index ce2ef0475339..ea890911d4fa 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -2423,11 +2423,14 @@ int ata_eh_reset(struct ata_link *link, int classify,
                }
                /* prereset() might have cleared ATA_EH_RESET.  If so,
-                 * bang classes and return.
+                 * bang classes, thaw and return.
                 */
                if (reset && !(ehc->i.action & ATA_EH_RESET)) {
                        ata_for_each_dev(dev, link, ALL)
                                classes[dev->devno] = ATA_DEV_NONE;
+                        if ((ap->pflags & ATA_PFLAG_FROZEN) &&
+                            ata_is_host_link(link))
+                                ata_eh_thaw_port(ap);
                        rc = 0;
                        goto out;
                }
@@ -2901,7 +2904,7 @@ static int atapi_eh_clear_ua(struct ata_device *dev)
        int i;
        for (i = 0; i < ATA_EH_UA_TRIES; i++) {
-                u8 sense_buffer[SCSI_SENSE_BUFFERSIZE];
+                u8 *sense_buffer = dev->link->ap->sector_buf;
                u8 sense_key = 0;
                unsigned int err_mask;
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 55a8eed3f3a3..f65b53785a8f 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -2523,7 +2523,7 @@ static void __exit nv_exit(void)
 module_init(nv_init);
 module_exit(nv_exit);
 module_param_named(adma, adma_enabled, bool, 0444);
-MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: true)");
+MODULE_PARM_DESC(adma, "Enable use of ADMA (Default: false)");
 module_param_named(swncq, swncq_enabled, bool, 0444);
 MODULE_PARM_DESC(swncq, "Enable use of SWNCQ (Default: true)");
diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c
index b5a061114630..4f9b6d792017 100644
--- a/drivers/block/cciss.c
+++ b/drivers/block/cciss.c
@@ -3606,11 +3606,9 @@ static int __devinit cciss_init_one(struct pci_dev *pdev,
                if (cciss_hard_reset_controller(pdev) || cciss_reset_msi(pdev))
                        return -ENODEV;
-                /* Some devices (notably the HP Smart Array 5i Controller)
+                /* Now try to get the controller to respond to a no-op. Some
-                   need a little pause here */
+                   devices (notably the HP Smart Array 5i Controller) need
-                schedule_timeout_uninterruptible(30*HZ);
+                   up to 30 seconds to respond. */
-                /* Now try to get the controller to respond to a no-op */
                for (i=0; i<30; i++) {
                        if (cciss_noop(pdev) == 0)
                                break;
diff --git a/drivers/block/loop.c b/drivers/block/loop.c
index edbaac6c0573..bf0345577672 100644
--- a/drivers/block/loop.c
+++ b/drivers/block/loop.c
@@ -392,8 +392,7 @@ lo_splice_actor(struct pipe_inode_info *pipe, struct pipe_buffer *buf,
        struct loop_device *lo = p->lo;
        struct page *page = buf->page;
        sector_t IV;
-        size_t size;
+        int size, ret;
-        int ret;
        ret = buf->ops->confirm(pipe, buf);
        if (unlikely(ret))
diff --git a/drivers/block/xen-blkfront.c b/drivers/block/xen-blkfront.c
index b6c8ce254359..8f905089b72b 100644
--- a/drivers/block/xen-blkfront.c
+++ b/drivers/block/xen-blkfront.c
@@ -977,6 +977,8 @@ static void backend_changed(struct xenbus_device *dev,
                break;
        case XenbusStateClosing:
+                if (info->gd == NULL)
+                        xenbus_dev_fatal(dev, -ENODEV, "gd is NULL");
                bd = bdget_disk(info->gd, 0);
                if (bd == NULL)
                        xenbus_dev_fatal(dev, -ENODEV, "bdget failed");
diff --git a/drivers/dca/dca-core.c b/drivers/dca/dca-core.c
index 33bd75347518..25b743abfb59 100644
--- a/drivers/dca/dca-core.c
+++ b/drivers/dca/dca-core.c
@@ -1,5 +1,5 @@
 /*
- * Copyright(c) 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2007 - 2009 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the Free
diff --git a/drivers/dma/dmatest.c b/drivers/dma/dmatest.c
index 732fa1ec36ab..e190d8b30700 100644
--- a/drivers/dma/dmatest.c
+++ b/drivers/dma/dmatest.c
@@ -430,13 +430,15 @@ late_initcall(dmatest_init);
 static void __exit dmatest_exit(void)
 {
        struct dmatest_chan *dtc, *_dtc;
+        struct dma_chan *chan;
        list_for_each_entry_safe(dtc, _dtc, &dmatest_channels, node) {
                list_del(&dtc->node);
+                chan = dtc->chan;
                dmatest_cleanup_channel(dtc);
                pr_debug("dmatest: dropped channel %s\n",
-                         dma_chan_name(dtc->chan));
+                         dma_chan_name(chan));
-                dma_release_channel(dtc->chan);
+                dma_release_channel(chan);
        }
 }
 module_exit(dmatest_exit);
diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c
index 70126a606239..86d6da47f558 100644
--- a/drivers/dma/fsldma.c
+++ b/drivers/dma/fsldma.c
@@ -158,7 +158,8 @@ static void dma_start(struct fsl_dma_chan *fsl_chan)
 static void dma_halt(struct fsl_dma_chan *fsl_chan)
 {
-        int i = 0;
+        int i;
        DMA_OUT(fsl_chan, &fsl_chan->reg_base->mr,
                DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32) | FSL_DMA_MR_CA,
                32);
@@ -166,8 +167,11 @@ static void dma_halt(struct fsl_dma_chan *fsl_chan)
                DMA_IN(fsl_chan, &fsl_chan->reg_base->mr, 32) & ~(FSL_DMA_MR_CS
                | FSL_DMA_MR_EMS_EN | FSL_DMA_MR_CA), 32);
-        while (!dma_is_idle(fsl_chan) && (i++ < 100))
+        for (i = 0; i < 100; i++) {
+                if (dma_is_idle(fsl_chan))
+                        break;
                udelay(10);
+        }
        if (i >= 100 && !dma_is_idle(fsl_chan))
                dev_err(fsl_chan->dev, "DMA halt timeout!\n");
 }
diff --git a/drivers/dma/ioat.c b/drivers/dma/ioat.c
index 4105d6575b64..ed83dd9df192 100644
--- a/drivers/dma/ioat.c
+++ b/drivers/dma/ioat.c
@@ -1,6 +1,6 @@
 /*
 * Intel I/OAT DMA Linux driver
- * Copyright(c) 2007 Intel Corporation.
+ * Copyright(c) 2007 - 2009 Intel Corporation.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms and conditions of the GNU General Public License,
diff --git a/drivers/dma/ioat_dca.c b/drivers/dma/ioat_dca.c
index 6cf622da0286..c012a1e15043 100644
--- a/drivers/dma/ioat_dca.c
+++ b/drivers/dma/ioat_dca.c
@@ -1,6 +1,6 @@
 /*
 * Intel I/OAT DMA Linux driver
- * Copyright(c) 2007 Intel Corporation.
+ * Copyright(c) 2007 - 2009 Intel Corporation.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms and conditions of the GNU General Public License,
@@ -49,6 +49,23 @@
 #define DCA_TAG_MAP_MASK 0xDF
+/* expected tag map bytes for I/OAT ver.2 */
+#define DCA2_TAG_MAP_BYTE0 0x80
+#define DCA2_TAG_MAP_BYTE1 0x0
+#define DCA2_TAG_MAP_BYTE2 0x81
+#define DCA2_TAG_MAP_BYTE3 0x82
+#define DCA2_TAG_MAP_BYTE4 0x82
+/* verify if tag map matches expected values */
+static inline int dca2_tag_map_valid(u8 *tag_map)
+{
+        return ((tag_map[0] == DCA2_TAG_MAP_BYTE0) &&
+                (tag_map[1] == DCA2_TAG_MAP_BYTE1) &&
+                (tag_map[2] == DCA2_TAG_MAP_BYTE2) &&
+                (tag_map[3] == DCA2_TAG_MAP_BYTE3) &&
+                (tag_map[4] == DCA2_TAG_MAP_BYTE4));
+}
 /*
 * "Legacy" DCA systems do not implement the DCA register set in the
 * I/OAT device.  Software needs direct support for their tag mappings.
@@ -452,6 +469,13 @@ struct dca_provider *ioat2_dca_init(struct pci_dev *pdev, void __iomem *iobase)
                        ioatdca->tag_map[i] = 0;
        }
+        if (!dca2_tag_map_valid(ioatdca->tag_map)) {
+                dev_err(&pdev->dev, "APICID_TAG_MAP set incorrectly by BIOS, "
+                        "disabling DCA\n");
+                free_dca_provider(dca);
+                return NULL;
+        }
        err = register_dca_provider(dca, &pdev->dev);
        if (err) {
                free_dca_provider(dca);
diff --git a/drivers/dma/ioat_dma.c b/drivers/dma/ioat_dma.c
index b3759c4b6536..5905cd36bcd2 100644
--- a/drivers/dma/ioat_dma.c
+++ b/drivers/dma/ioat_dma.c
@@ -1,6 +1,6 @@
 /*
 * Intel I/OAT DMA Linux driver
- * Copyright(c) 2004 - 2007 Intel Corporation.
+ * Copyright(c) 2004 - 2009 Intel Corporation.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms and conditions of the GNU General Public License,
@@ -189,11 +189,13 @@ static int ioat_dma_enumerate_channels(struct ioatdma_device *device)
                ioat_chan->xfercap = xfercap;
                ioat_chan->desccount = 0;
                INIT_DELAYED_WORK(&ioat_chan->work, ioat_dma_chan_reset_part2);
-                if (ioat_chan->device->version != IOAT_VER_1_2) {
+                if (ioat_chan->device->version == IOAT_VER_2_0)
-                        writel(IOAT_DCACTRL_CMPL_WRITE_ENABLE
+                        writel(IOAT_DCACTRL_CMPL_WRITE_ENABLE |
-                                        | IOAT_DMA_DCA_ANY_CPU,
+                               IOAT_DMA_DCA_ANY_CPU,
-                                ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
+                               ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
-                }
+                else if (ioat_chan->device->version == IOAT_VER_3_0)
+                        writel(IOAT_DMA_DCA_ANY_CPU,
+                               ioat_chan->reg_base + IOAT_DCACTRL_OFFSET);
                spin_lock_init(&ioat_chan->cleanup_lock);
                spin_lock_init(&ioat_chan->desc_lock);
                INIT_LIST_HEAD(&ioat_chan->free_desc);
@@ -1169,9 +1171,8 @@ static void ioat_dma_memcpy_cleanup(struct ioat_dma_chan *ioat_chan)
                                 * up if the client is done with the descriptor
                                 */
                                if (async_tx_test_ack(&desc->async_tx)) {
-                                        list_del(&desc->node);
+                                        list_move_tail(&desc->node,
-                                        list_add_tail(&desc->node,
+                                                       &ioat_chan->free_desc);
-                                                      &ioat_chan->free_desc);
                                } else
                                        desc->async_tx.cookie = 0;
                        } else {
@@ -1362,6 +1363,7 @@ static int ioat_dma_self_test(struct ioatdma_device *device)
        dma_cookie_t cookie;
        int err = 0;
        struct completion cmp;
+        unsigned long tmo;
        src = kzalloc(sizeof(u8) * IOAT_TEST_SIZE, GFP_KERNEL);
        if (!src)
@@ -1413,9 +1415,10 @@ static int ioat_dma_self_test(struct ioatdma_device *device)
        }
        device->common.device_issue_pending(dma_chan);
-        wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
+        tmo = wait_for_completion_timeout(&cmp, msecs_to_jiffies(3000));
-        if (device->common.device_is_tx_complete(dma_chan, cookie, NULL, NULL)
+        if (tmo == 0 ||
+            device->common.device_is_tx_complete(dma_chan, cookie, NULL, NULL)
                                        != DMA_SUCCESS) {
                dev_err(&device->pdev->dev,
                        "Self-test copy timed out, disabling\n");
@@ -1657,6 +1660,13 @@ struct ioatdma_device *ioat_dma_probe(struct pci_dev *pdev,
                " %d channels, device version 0x%02x, driver version %s\n",
                device->common.chancnt, device->version, IOAT_DMA_VERSION);
+        if (!device->common.chancnt) {
+                dev_err(&device->pdev->dev,
+                        "Intel(R) I/OAT DMA Engine problem found: "
+                        "zero channels detected\n");
+                goto err_setup_interrupts;
+        }
        err = ioat_dma_setup_interrupts(device);
        if (err)
                goto err_setup_interrupts;
@@ -1696,6 +1706,9 @@ void ioat_dma_remove(struct ioatdma_device *device)
        struct dma_chan *chan, *_chan;
        struct ioat_dma_chan *ioat_chan;
+        if (device->version != IOAT_VER_3_0)
+                cancel_delayed_work(&device->work);
        ioat_dma_remove_interrupts(device);
        dma_async_device_unregister(&device->common);
@@ -1707,10 +1720,6 @@ void ioat_dma_remove(struct ioatdma_device *device)
        pci_release_regions(device->pdev);
        pci_disable_device(device->pdev);
-        if (device->version != IOAT_VER_3_0) {
-                cancel_delayed_work(&device->work);
-        }
        list_for_each_entry_safe(chan, _chan,
                                 &device->common.channels, device_node) {
                ioat_chan = to_ioat_chan(chan);
diff --git a/drivers/dma/ioatdma.h b/drivers/dma/ioatdma.h
index a3306d0e1372..a52ff4bd4601 100644
--- a/drivers/dma/ioatdma.h
+++ b/drivers/dma/ioatdma.h
@@ -1,5 +1,5 @@
 /*
- * Copyright(c) 2004 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the Free
@@ -29,7 +29,7 @@
 #include <linux/pci_ids.h>
 #include <net/tcp.h>
-#define IOAT_DMA_VERSION  "3.30"
+#define IOAT_DMA_VERSION  "3.64"
 enum ioat_interrupt {
        none = 0,
@@ -135,12 +135,14 @@ static inline void ioat_set_tcp_copy_break(struct ioatdma_device *dev)
        #ifdef CONFIG_NET_DMA
        switch (dev->version) {
        case IOAT_VER_1_2:
-        case IOAT_VER_3_0:
                sysctl_tcp_dma_copybreak = 4096;
                break;
        case IOAT_VER_2_0:
                sysctl_tcp_dma_copybreak = 2048;
                break;
+        case IOAT_VER_3_0:
+                sysctl_tcp_dma_copybreak = 262144;
+                break;
        }
        #endif
 }
diff --git a/drivers/dma/ioatdma_hw.h b/drivers/dma/ioatdma_hw.h
index f1ae2c776f74..afa57eef86c9 100644
--- a/drivers/dma/ioatdma_hw.h
+++ b/drivers/dma/ioatdma_hw.h
@@ -1,5 +1,5 @@
 /*
- * Copyright(c) 2004 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the Free
diff --git a/drivers/dma/ioatdma_registers.h b/drivers/dma/ioatdma_registers.h
index 827cb503cac6..49bc277424f8 100644
--- a/drivers/dma/ioatdma_registers.h
+++ b/drivers/dma/ioatdma_registers.h
@@ -1,5 +1,5 @@
 /*
- * Copyright(c) 2004 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2004 - 2009 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the Free
diff --git a/drivers/dma/iop-adma.c b/drivers/dma/iop-adma.c
index 647374acba94..16adbe61cfb2 100644
--- a/drivers/dma/iop-adma.c
+++ b/drivers/dma/iop-adma.c
@@ -928,19 +928,19 @@ iop_adma_xor_zero_sum_self_test(struct iop_adma_device *device)
        for (src_idx = 0; src_idx < IOP_ADMA_NUM_SRC_TEST; src_idx++) {
                xor_srcs[src_idx] = alloc_page(GFP_KERNEL);
-                if (!xor_srcs[src_idx])
+                if (!xor_srcs[src_idx]) {
-                        while (src_idx--) {
+                        while (src_idx--)
                                __free_page(xor_srcs[src_idx]);
-                                return -ENOMEM;
+                        return -ENOMEM;
-                        }
+                }
        }
        dest = alloc_page(GFP_KERNEL);
-        if (!dest)
+        if (!dest) {
-                while (src_idx--) {
+                while (src_idx--)
                        __free_page(xor_srcs[src_idx]);
-                        return -ENOMEM;
+                return -ENOMEM;
-                }
+        }
        /* Fill in src buffers */
        for (src_idx = 0; src_idx < IOP_ADMA_NUM_SRC_TEST; src_idx++) {
diff --git a/drivers/dma/ipu/ipu_idmac.c b/drivers/dma/ipu/ipu_idmac.c
index 1f154d08e98f..ae50a9d1a4e6 100644
--- a/drivers/dma/ipu/ipu_idmac.c
+++ b/drivers/dma/ipu/ipu_idmac.c
@@ -729,7 +729,7 @@ static int ipu_init_channel_buffer(struct idmac_channel *ichan,
        ichan->status = IPU_CHANNEL_READY;
-        spin_unlock_irqrestore(ipu->lock, flags);
+        spin_unlock_irqrestore(&ipu->lock, flags);
        return 0;
 }
diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c
index 5d5d5b31867f..cb7f26fb9f18 100644
--- a/drivers/dma/mv_xor.c
+++ b/drivers/dma/mv_xor.c
@@ -1019,19 +1019,19 @@ mv_xor_xor_self_test(struct mv_xor_device *device)
        for (src_idx = 0; src_idx < MV_XOR_NUM_SRC_TEST; src_idx++) {
                xor_srcs[src_idx] = alloc_page(GFP_KERNEL);
-                if (!xor_srcs[src_idx])
+                if (!xor_srcs[src_idx]) {
-                        while (src_idx--) {
+                        while (src_idx--)
                                __free_page(xor_srcs[src_idx]);
-                                return -ENOMEM;
+                        return -ENOMEM;
-                        }
+                }
        }
        dest = alloc_page(GFP_KERNEL);
-        if (!dest)
+        if (!dest) {
-                while (src_idx--) {
+                while (src_idx--)
                        __free_page(xor_srcs[src_idx]);
-                        return -ENOMEM;
+                return -ENOMEM;
-                }
+        }
        /* Fill in src buffers */
        for (src_idx = 0; src_idx < MV_XOR_NUM_SRC_TEST; src_idx++) {
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index e072903b12f0..5ea3bfad172a 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -721,6 +721,11 @@ config BLK_DEV_IDE_TX4939
        depends on SOC_TX4939
        select BLK_DEV_IDEDMA_SFF
+config BLK_DEV_IDE_AT91
+        tristate "Atmel AT91 (SAM9, CAP9, AT572D940HF) IDE support"
+        depends on ARM && ARCH_AT91 && !ARCH_AT91RM9200 && !ARCH_AT91X40
+        select IDE_TIMINGS
 config IDE_ARM
        tristate "ARM IDE support"
        depends on ARM && (ARCH_RPC || ARCH_SHARK)
diff --git a/drivers/ide/Makefile b/drivers/ide/Makefile
index d0e3d7d5b467..1c326d94aa6d 100644
--- a/drivers/ide/Makefile
+++ b/drivers/ide/Makefile
@@ -116,3 +116,4 @@ obj-$(CONFIG_BLK_DEV_IDE_AU1XXX)	+= au1xxx-ide.o
 obj-$(CONFIG_BLK_DEV_IDE_TX4938)        += tx4938ide.o
 obj-$(CONFIG_BLK_DEV_IDE_TX4939)        += tx4939ide.o
+obj-$(CONFIG_BLK_DEV_IDE_AT91)          += at91_ide.o
diff --git a/drivers/ide/at91_ide.c b/drivers/ide/at91_ide.c
new file mode 100644
index 000000000000..1bb50f46388d
--- /dev/null
+++ b/drivers/ide/at91_ide.c
@@ -0,0 +1,467 @@
+/*
+ * IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory Controller
+ * with Compact Flash True IDE logic
+ *
+ * Copyright (c) 2008, 2009 Kelvatek Ltd.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+#include <linux/version.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/ide.h>
+#include <linux/platform_device.h>
+#include <mach/board.h>
+#include <mach/gpio.h>
+#include <mach/at91sam9263.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/at91sam9263_matrix.h>
+#define DRV_NAME "at91_ide"
+#define perr(fmt, args...) pr_err(DRV_NAME ": " fmt, ##args)
+#define pdbg(fmt, args...) pr_debug("%s " fmt, __func__, ##args)
+/*
+ * Access to IDE device is possible through EBI Static Memory Controller
+ * with Compact Flash logic. For details see EBI and SMC datasheet sections
+ * of any microcontroller from AT91SAM9 family.
+ *
+ * Within SMC chip select address space, lines A[23:21] distinguish Compact
+ * Flash modes (I/O, common memory, attribute memory, True IDE). IDE modes are:
+ *   0x00c0000 - True IDE
+ *   0x00e0000 - Alternate True IDE (Alt Status Register)
+ *
+ * On True IDE mode Task File and Data Register are mapped at the same address.
+ * To distinguish access between these two different bus data width is used:
+ * 8Bit for Task File, 16Bit for Data I/O.
+ *
+ * After initialization we do 8/16 bit flipping (changes in SMC MODE register)
+ * only inside IDE callback routines which are serialized by IDE layer,
+ * so no additional locking needed.
+ */
+#define TASK_FILE       0x00c00000
+#define ALT_MODE        0x00e00000
+#define REGS_SIZE       8
+#define enter_16bit(cs, mode) do {                                      \
+        mode = at91_sys_read(AT91_SMC_MODE(cs));                        \
+        at91_sys_write(AT91_SMC_MODE(cs), mode | AT91_SMC_DBW_16);      \
+} while (0)
+#define leave_16bit(cs, mode) at91_sys_write(AT91_SMC_MODE(cs), mode);
+static void set_smc_timings(const u8 chipselect, const u16 cycle,
+                            const u16 setup, const u16 pulse,
+                            const u16 data_float, int use_iordy)
+{
+        unsigned long mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE |
+                             AT91_SMC_BAT_SELECT;
+        /* disable or enable waiting for IORDY signal */
+        if (use_iordy)
+                mode |= AT91_SMC_EXNWMODE_READY;
+        /* add data float cycles if needed */
+        if (data_float)
+                mode |= AT91_SMC_TDF_(data_float);
+        at91_sys_write(AT91_SMC_MODE(chipselect), mode);
+        /* setup timings in SMC */
+        at91_sys_write(AT91_SMC_SETUP(chipselect), AT91_SMC_NWESETUP_(setup) |
+                                                   AT91_SMC_NCS_WRSETUP_(0) |
+                                                   AT91_SMC_NRDSETUP_(setup) |
+                                                   AT91_SMC_NCS_RDSETUP_(0));
+        at91_sys_write(AT91_SMC_PULSE(chipselect), AT91_SMC_NWEPULSE_(pulse) |
+                                                   AT91_SMC_NCS_WRPULSE_(cycle) |
+                                                   AT91_SMC_NRDPULSE_(pulse) |
+                                                   AT91_SMC_NCS_RDPULSE_(cycle));
+        at91_sys_write(AT91_SMC_CYCLE(chipselect), AT91_SMC_NWECYCLE_(cycle) |
+                                                   AT91_SMC_NRDCYCLE_(cycle));
+}
+static unsigned int calc_mck_cycles(unsigned int ns, unsigned int mck_hz)
+{
+        u64 tmp = ns;
+        tmp *= mck_hz;
+        tmp += 1000*1000*1000 - 1; /* round up */
+        do_div(tmp, 1000*1000*1000);
+        return (unsigned int) tmp;
+}
+static void apply_timings(const u8 chipselect, const u8 pio,
+                          const struct ide_timing *timing, int use_iordy)
+{
+        unsigned int t0, t1, t2, t6z;
+        unsigned int cycle, setup, pulse, data_float;
+        unsigned int mck_hz;
+        struct clk *mck;
+        /* see table 22 of Compact Flash standard 4.1 for the meaning,
+         * we do not stretch active (t2) time, so setup (t1) + hold time (th)
+         * assure at least minimal recovery (t2i) time */
+        t0 = timing->cyc8b;
+        t1 = timing->setup;
+        t2 = timing->act8b;
+        t6z = (pio < 5) ? 30 : 20;
+        pdbg("t0=%u t1=%u t2=%u t6z=%u\n", t0, t1, t2, t6z);
+        mck = clk_get(NULL, "mck");
+        BUG_ON(IS_ERR(mck));
+        mck_hz = clk_get_rate(mck);
+        pdbg("mck_hz=%u\n", mck_hz);
+        cycle = calc_mck_cycles(t0, mck_hz);
+        setup = calc_mck_cycles(t1, mck_hz);
+        pulse = calc_mck_cycles(t2, mck_hz);
+        data_float = calc_mck_cycles(t6z, mck_hz);
+        pdbg("cycle=%u setup=%u pulse=%u data_float=%u\n",
+             cycle, setup, pulse, data_float);
+        set_smc_timings(chipselect, cycle, setup, pulse, data_float, use_iordy);
+}
+static void at91_ide_input_data(ide_drive_t *drive, struct request *rq,
+                                void *buf, unsigned int len)
+{
+        ide_hwif_t *hwif = drive->hwif;
+        struct ide_io_ports *io_ports = &hwif->io_ports;
+        u8 chipselect = hwif->select_data;
+        unsigned long mode;
+        pdbg("cs %u buf %p len %d\n", chipselect, buf, len);
+        len++;
+        enter_16bit(chipselect, mode);
+        __ide_mm_insw((void __iomem *) io_ports->data_addr, buf, len / 2);
+        leave_16bit(chipselect, mode);
+}
+static void at91_ide_output_data(ide_drive_t *drive, struct request *rq,
+                                 void *buf, unsigned int len)
+{
+        ide_hwif_t *hwif = drive->hwif;
+        struct ide_io_ports *io_ports = &hwif->io_ports;
+        u8 chipselect = hwif->select_data;
+        unsigned long mode;
+        pdbg("cs %u buf %p len %d\n", chipselect,  buf, len);
+        enter_16bit(chipselect, mode);
+        __ide_mm_outsw((void __iomem *) io_ports->data_addr, buf, len / 2);
+        leave_16bit(chipselect, mode);
+}
+static u8 ide_mm_inb(unsigned long port)
+{
+        return readb((void __iomem *) port);
+}
+static void ide_mm_outb(u8 value, unsigned long port)
+{
+        writeb(value, (void __iomem *) port);
+}
+static void at91_ide_tf_load(ide_drive_t *drive, ide_task_t *task)
+{
+        ide_hwif_t *hwif = drive->hwif;
+        struct ide_io_ports *io_ports = &hwif->io_ports;
+        struct ide_taskfile *tf = &task->tf;
+        u8 HIHI = (task->tf_flags & IDE_TFLAG_LBA48) ? 0xE0 : 0xEF;
+        if (task->tf_flags & IDE_TFLAG_FLAGGED)
+                HIHI = 0xFF;
+        if (task->tf_flags & IDE_TFLAG_OUT_DATA) {
+                u16 data = (tf->hob_data << 8) | tf->data;
+                at91_ide_output_data(drive, NULL, &data, 2);
+        }
+        if (task->tf_flags & IDE_TFLAG_OUT_HOB_FEATURE)
+                ide_mm_outb(tf->hob_feature, io_ports->feature_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_HOB_NSECT)
+                ide_mm_outb(tf->hob_nsect, io_ports->nsect_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAL)
+                ide_mm_outb(tf->hob_lbal, io_ports->lbal_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAM)
+                ide_mm_outb(tf->hob_lbam, io_ports->lbam_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_HOB_LBAH)
+                ide_mm_outb(tf->hob_lbah, io_ports->lbah_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_FEATURE)
+                ide_mm_outb(tf->feature, io_ports->feature_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_NSECT)
+                ide_mm_outb(tf->nsect, io_ports->nsect_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_LBAL)
+                ide_mm_outb(tf->lbal, io_ports->lbal_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_LBAM)
+                ide_mm_outb(tf->lbam, io_ports->lbam_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_LBAH)
+                ide_mm_outb(tf->lbah, io_ports->lbah_addr);
+        if (task->tf_flags & IDE_TFLAG_OUT_DEVICE)
+                ide_mm_outb((tf->device & HIHI) | drive->select, io_ports->device_addr);
+}
+static void at91_ide_tf_read(ide_drive_t *drive, ide_task_t *task)
+{
+        ide_hwif_t *hwif = drive->hwif;
+        struct ide_io_ports *io_ports = &hwif->io_ports;
+        struct ide_taskfile *tf = &task->tf;
+        if (task->tf_flags & IDE_TFLAG_IN_DATA) {
+                u16 data;
+                at91_ide_input_data(drive, NULL, &data, 2);
+                tf->data = data & 0xff;
+                tf->hob_data = (data >> 8) & 0xff;
+        }
+        /* be sure we're looking at the low order bits */
+        ide_mm_outb(ATA_DEVCTL_OBS & ~0x80, io_ports->ctl_addr);
+        if (task->tf_flags & IDE_TFLAG_IN_FEATURE)
+                tf->feature = ide_mm_inb(io_ports->feature_addr);
+        if (task->tf_flags & IDE_TFLAG_IN_NSECT)
+                tf->nsect  = ide_mm_inb(io_ports->nsect_addr);
+        if (task->tf_flags & IDE_TFLAG_IN_LBAL)
+                tf->lbal   = ide_mm_inb(io_ports->lbal_addr);
+        if (task->tf_flags & IDE_TFLAG_IN_LBAM)
+                tf->lbam   = ide_mm_inb(io_ports->lbam_addr);
+        if (task->tf_flags & IDE_TFLAG_IN_LBAH)
+                tf->lbah   = ide_mm_inb(io_ports->lbah_addr);
+        if (task->tf_flags & IDE_TFLAG_IN_DEVICE)
+                tf->device = ide_mm_inb(io_ports->device_addr);
+        if (task->tf_flags & IDE_TFLAG_LBA48) {
+                ide_mm_outb(ATA_DEVCTL_OBS | 0x80, io_ports->ctl_addr);
+                if (task->tf_flags & IDE_TFLAG_IN_HOB_FEATURE)
+                        tf->hob_feature = ide_mm_inb(io_ports->feature_addr);
+                if (task->tf_flags & IDE_TFLAG_IN_HOB_NSECT)
+                        tf->hob_nsect   = ide_mm_inb(io_ports->nsect_addr);
+                if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAL)
+                        tf->hob_lbal    = ide_mm_inb(io_ports->lbal_addr);
+                if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAM)
+                        tf->hob_lbam    = ide_mm_inb(io_ports->lbam_addr);
+                if (task->tf_flags & IDE_TFLAG_IN_HOB_LBAH)
+                        tf->hob_lbah    = ide_mm_inb(io_ports->lbah_addr);
+        }
+}
+static void at91_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+        struct ide_timing *timing;
+        u8 chipselect = drive->hwif->select_data;
+        int use_iordy = 0;
+        pdbg("chipselect %u pio %u\n", chipselect, pio);
+        timing = ide_timing_find_mode(XFER_PIO_0 + pio);
+        BUG_ON(!timing);
+        if ((pio > 2 || ata_id_has_iordy(drive->id)) &&
+            !(ata_id_is_cfa(drive->id) && pio > 4))
+                use_iordy = 1;
+        apply_timings(chipselect, pio, timing, use_iordy);
+}
+static const struct ide_tp_ops at91_ide_tp_ops = {
+        .exec_command   = ide_exec_command,
+        .read_status    = ide_read_status,
+        .read_altstatus = ide_read_altstatus,
+        .set_irq        = ide_set_irq,
+        .tf_load        = at91_ide_tf_load,
+        .tf_read        = at91_ide_tf_read,
+        .input_data     = at91_ide_input_data,
+        .output_data    = at91_ide_output_data,
+};
+static const struct ide_port_ops at91_ide_port_ops = {
+        .set_pio_mode   = at91_ide_set_pio_mode,
+};
+static const struct ide_port_info at91_ide_port_info __initdata = {
+        .port_ops       = &at91_ide_port_ops,
+        .tp_ops         = &at91_ide_tp_ops,
+        .host_flags     = IDE_HFLAG_MMIO | IDE_HFLAG_NO_DMA | IDE_HFLAG_SINGLE |
+                          IDE_HFLAG_NO_IO_32BIT | IDE_HFLAG_UNMASK_IRQS,
+        .pio_mask       = ATA_PIO5,
+};
+/*
+ * If interrupt is delivered through GPIO, IRQ are triggered on falling
+ * and rising edge of signal. Whereas IDE device request interrupt on high
+ * level (rising edge in our case). This mean we have fake interrupts, so
+ * we need to check interrupt pin and exit instantly from ISR when line
+ * is on low level.
+ */
+irqreturn_t at91_irq_handler(int irq, void *dev_id)
+{
+        int ntries = 8;
+        int pin_val1, pin_val2;
+        /* additional deglitch, line can be noisy in badly designed PCB */
+        do {
+                pin_val1 = at91_get_gpio_value(irq);
+                pin_val2 = at91_get_gpio_value(irq);
+        } while (pin_val1 != pin_val2 && --ntries > 0);
+        if (pin_val1 == 0 || ntries <= 0)
+                return IRQ_HANDLED;
+        return ide_intr(irq, dev_id);
+}
+static int __init at91_ide_probe(struct platform_device *pdev)
+{
+        int ret;
+        hw_regs_t hw;
+        hw_regs_t *hws[] = { &hw, NULL, NULL, NULL };
+        struct ide_host *host;
+        struct resource *res;
+        unsigned long tf_base = 0, ctl_base = 0;
+        struct at91_cf_data *board = pdev->dev.platform_data;
+        if (!board)
+                return -ENODEV;
+        if (board->det_pin && at91_get_gpio_value(board->det_pin) != 0) {
+                perr("no device detected\n");
+                return -ENODEV;
+        }
+        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+        if (!res) {
+                perr("can't get memory resource\n");
+                return -ENODEV;
+        }
+        if (!devm_request_mem_region(&pdev->dev, res->start + TASK_FILE,
+                                     REGS_SIZE, "ide") ||
+            !devm_request_mem_region(&pdev->dev, res->start + ALT_MODE,
+                                     REGS_SIZE, "alt")) {
+                perr("memory resources in use\n");
+                return -EBUSY;
+        }
+        pdbg("chipselect %u irq %u res %08lx\n", board->chipselect,
+             board->irq_pin, (unsigned long) res->start);
+        tf_base = (unsigned long) devm_ioremap(&pdev->dev, res->start + TASK_FILE,
+                                               REGS_SIZE);
+        ctl_base = (unsigned long) devm_ioremap(&pdev->dev, res->start + ALT_MODE,
+                                                REGS_SIZE);
+        if (!tf_base || !ctl_base) {
+                perr("can't map memory regions\n");
+                return -EBUSY;
+        }
+        memset(&hw, 0, sizeof(hw));
+        if (board->flags & AT91_IDE_SWAP_A0_A2) {
+                /* workaround for stupid hardware bug */
+                hw.io_ports.data_addr   = tf_base + 0;
+                hw.io_ports.error_addr  = tf_base + 4;
+                hw.io_ports.nsect_addr  = tf_base + 2;
+                hw.io_ports.lbal_addr   = tf_base + 6;
+                hw.io_ports.lbam_addr   = tf_base + 1;
+                hw.io_ports.lbah_addr   = tf_base + 5;
+                hw.io_ports.device_addr = tf_base + 3;
+                hw.io_ports.command_addr = tf_base + 7;
+                hw.io_ports.ctl_addr    = ctl_base + 3;
+        } else
+                ide_std_init_ports(&hw, tf_base, ctl_base + 6);
+        hw.irq = board->irq_pin;
+        hw.chipset = ide_generic;
+        hw.dev = &pdev->dev;
+        host = ide_host_alloc(&at91_ide_port_info, hws);
+        if (!host) {
+                perr("failed to allocate ide host\n");
+                return -ENOMEM;
+        }
+        /* setup Static Memory Controller - PIO 0 as default */
+        apply_timings(board->chipselect, 0, ide_timing_find_mode(XFER_PIO_0), 0);
+        /* with GPIO interrupt we have to do quirks in handler */
+        if (board->irq_pin >= PIN_BASE)
+                host->irq_handler = at91_irq_handler;
+        host->ports[0]->select_data = board->chipselect;
+        ret = ide_host_register(host, &at91_ide_port_info, hws);
+        if (ret) {
+                perr("failed to register ide host\n");
+                goto err_free_host;
+        }
+        platform_set_drvdata(pdev, host);
+        return 0;
+err_free_host:
+        ide_host_free(host);
+        return ret;
+}
+static int __exit at91_ide_remove(struct platform_device *pdev)
+{
+        struct ide_host *host = platform_get_drvdata(pdev);
+        ide_host_remove(host);
+        return 0;
+}
+static struct platform_driver at91_ide_driver = {
+        .driver = {
+                .name = DRV_NAME,
+                .owner = THIS_MODULE,
+        },
+        .remove = __exit_p(at91_ide_remove),
+};
+static int __init at91_ide_init(void)
+{
+        return platform_driver_probe(&at91_ide_driver, at91_ide_probe);
+}
+static void __exit at91_ide_exit(void)
+{
+        platform_driver_unregister(&at91_ide_driver);
+}
+module_init(at91_ide_init);
+module_exit(at91_ide_exit);
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Stanislaw Gruszka <stf_xl@wp.pl>");
diff --git a/drivers/ide/ide-disk_proc.c b/drivers/ide/ide-disk_proc.c
index 1146f4204c6e..1f86dcbd2b1c 100644
--- a/drivers/ide/ide-disk_proc.c
+++ b/drivers/ide/ide-disk_proc.c
@@ -125,5 +125,5 @@ const struct ide_proc_devset ide_disk_settings[] = {
        IDE_PROC_DEVSET(multcount,      0,    16),
        IDE_PROC_DEVSET(nowerr,         0,     1),
        IDE_PROC_DEVSET(wcache,         0,     1),
-        { 0 },
+        { NULL },
 };
diff --git a/drivers/ide/ide-floppy_proc.c b/drivers/ide/ide-floppy_proc.c
index 3ec762cb60ab..fcd4d8153df5 100644
--- a/drivers/ide/ide-floppy_proc.c
+++ b/drivers/ide/ide-floppy_proc.c
@@ -29,5 +29,5 @@ const struct ide_proc_devset ide_floppy_settings[] = {
        IDE_PROC_DEVSET(bios_head, 0,  255),
        IDE_PROC_DEVSET(bios_sect, 0,   63),
        IDE_PROC_DEVSET(ticks,     0,  255),
-        { 0 },
+        { NULL },
 };
diff --git a/drivers/ide/ide-io.c b/drivers/ide/ide-io.c
index 9ee51adf567f..a9a6c208288a 100644
--- a/drivers/ide/ide-io.c
+++ b/drivers/ide/ide-io.c
@@ -908,7 +908,7 @@ void ide_timer_expiry (unsigned long data)
        ide_drive_t     *uninitialized_var(drive);
        ide_handler_t   *handler;
        unsigned long   flags;
-        unsigned long   wait = -1;
+        int             wait = -1;
        int             plug_device = 0;
        spin_lock_irqsave(&hwif->lock, flags);
@@ -1162,6 +1162,7 @@ out_early:
        return irq_ret;
 }
+EXPORT_SYMBOL_GPL(ide_intr);
 /**
 *      ide_do_drive_cmd        -       issue IDE special command
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 753b92ebe0ae..b1892bd95c6f 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -315,6 +315,8 @@ void ide_output_data(ide_drive_t *drive, struct request *rq, void *buf,
        u8 io_32bit = drive->io_32bit;
        u8 mmio = (hwif->host_flags & IDE_HFLAG_MMIO) ? 1 : 0;
+        len++;
        if (io_32bit) {
                unsigned long uninitialized_var(flags);
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index ce0818a993f6..ee8e3e7cad51 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -950,6 +950,7 @@ static int ide_port_setup_devices(ide_hwif_t *hwif)
 static int init_irq (ide_hwif_t *hwif)
 {
        struct ide_io_ports *io_ports = &hwif->io_ports;
+        irq_handler_t irq_handler;
        int sa = 0;
        mutex_lock(&ide_cfg_mtx);
@@ -959,6 +960,10 @@ static int init_irq (ide_hwif_t *hwif)
        hwif->timer.function = &ide_timer_expiry;
        hwif->timer.data = (unsigned long)hwif;
+        irq_handler = hwif->host->irq_handler;
+        if (irq_handler == NULL)
+                irq_handler = ide_intr;
 #if defined(__mc68000__)
        sa = IRQF_SHARED;
 #endif /* __mc68000__ */
@@ -969,7 +974,7 @@ static int init_irq (ide_hwif_t *hwif)
        if (io_ports->ctl_addr)
                hwif->tp_ops->set_irq(hwif, 1);
-        if (request_irq(hwif->irq, &ide_intr, sa, hwif->name, hwif))
+        if (request_irq(hwif->irq, irq_handler, sa, hwif->name, hwif))
                goto out_up;
        if (!hwif->rqsize) {
diff --git a/drivers/ide/ide-proc.c b/drivers/ide/ide-proc.c
index 1d8978b3314a..a7b9287ee0d4 100644
--- a/drivers/ide/ide-proc.c
+++ b/drivers/ide/ide-proc.c
@@ -231,7 +231,7 @@ static const struct ide_proc_devset ide_generic_settings[] = {
        IDE_PROC_DEVSET(pio_mode, 0, 255),
        IDE_PROC_DEVSET(unmaskirq, 0, 1),
        IDE_PROC_DEVSET(using_dma, 0, 1),
-        { 0 },
+        { NULL },
 };
 static void proc_ide_settings_warn(void)
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index bb450a7608c2..4e6181c7bbda 100644
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -2166,7 +2166,7 @@ static const struct ide_proc_devset idetape_settings[] = {
        __IDE_PROC_DEVSET(speed,        0, 0xffff, NULL, NULL),
        __IDE_PROC_DEVSET(tdsc,         IDETAPE_DSC_RW_MIN, IDETAPE_DSC_RW_MAX,
                                        mulf_tdsc, divf_tdsc),
-        { 0 },
+        { NULL },
 };
 #endif
diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
index 9c50e6f1c236..34ce2703d29a 100644
--- a/drivers/mmc/core/mmc_ops.c
+++ b/drivers/mmc/core/mmc_ops.c
@@ -248,12 +248,15 @@ mmc_send_cxd_data(struct mmc_card *card, struct mmc_host *host,
        sg_init_one(&sg, data_buf, len);
-        /*
+        if (opcode == MMC_SEND_CSD || opcode == MMC_SEND_CID) {
-         * The spec states that CSR and CID accesses have a timeout
+                /*
-         * of 64 clock cycles.
+                 * The spec states that CSR and CID accesses have a timeout
-         */
+                 * of 64 clock cycles.
-        data.timeout_ns = 0;
+                 */
-        data.timeout_clks = 64;
+                data.timeout_ns = 0;
+                data.timeout_clks = 64;
+        } else
+                mmc_set_data_timeout(&data, card);
        mmc_wait_for_req(host, &mrq);
diff --git a/drivers/watchdog/gef_wdt.c b/drivers/watchdog/gef_wdt.c
index f0c2b7a1a175..734d9806a872 100644
--- a/drivers/watchdog/gef_wdt.c
+++ b/drivers/watchdog/gef_wdt.c
@@ -269,7 +269,7 @@ static int __devinit gef_wdt_probe(struct of_device *dev,
        bus_clk = 133; /* in MHz */
        freq = fsl_get_sys_freq();
-        if (freq > 0)
+        if (freq != -1)
                bus_clk = freq;
        /* Map devices registers into memory */
diff --git a/drivers/watchdog/ks8695_wdt.c b/drivers/watchdog/ks8695_wdt.c
index 0b798fdaa378..74c92d384112 100644
--- a/drivers/watchdog/ks8695_wdt.c
+++ b/drivers/watchdog/ks8695_wdt.c
@@ -21,6 +21,7 @@
 #include <linux/watchdog.h>
 #include <linux/io.h>
 #include <linux/uaccess.h>
+#include <mach/timex.h>
 #include <mach/regs-timer.h>
 #define WDT_DEFAULT_TIME        5       /* seconds */
diff --git a/drivers/watchdog/orion5x_wdt.c b/drivers/watchdog/orion5x_wdt.c
index 14a339f58b6a..b64ae1a17832 100644
--- a/drivers/watchdog/orion5x_wdt.c
+++ b/drivers/watchdog/orion5x_wdt.c
@@ -29,6 +29,7 @@
 #define  WDT_EN                 0x0010
 #define WDT_VAL                 (TIMER_VIRT_BASE + 0x0024)
+#define ORION5X_TCLK            166666667
 #define WDT_MAX_DURATION        (0xffffffff / ORION5X_TCLK)
 #define WDT_IN_USE              0
 #define WDT_OK_TO_CLOSE         1
diff --git a/drivers/watchdog/rc32434_wdt.c b/drivers/watchdog/rc32434_wdt.c
index 57027f4653ce..f3553fa40b17 100644
--- a/drivers/watchdog/rc32434_wdt.c
+++ b/drivers/watchdog/rc32434_wdt.c
@@ -34,104 +34,89 @@
 #include <asm/time.h>
 #include <asm/mach-rc32434/integ.h>
-#define MAX_TIMEOUT                     20
+#define VERSION "0.4"
-#define RC32434_WDT_INTERVAL            (15 * HZ)
-#define VERSION "0.2"
 static struct {
-        struct completion stop;
-        int running;
-        struct timer_list timer;
-        int queue;
-        int default_ticks;
        unsigned long inuse;
 } rc32434_wdt_device;
 static struct integ __iomem *wdt_reg;
-static int ticks = 100 * HZ;
 static int expect_close;
-static int timeout;
+/* Board internal clock speed in Hz,
+ * the watchdog timer ticks at. */
+extern unsigned int idt_cpu_freq;
+/* translate wtcompare value to seconds and vice versa */
+#define WTCOMP2SEC(x)   (x / idt_cpu_freq)
+#define SEC2WTCOMP(x)   (x * idt_cpu_freq)
+/* Use a default timeout of 20s. This should be
+ * safe for CPU clock speeds up to 400MHz, as
+ * ((2 ^ 32) - 1) / (400MHz / 2) = 21s.  */
+#define WATCHDOG_TIMEOUT 20
+static int timeout = WATCHDOG_TIMEOUT;
 static int nowayout = WATCHDOG_NOWAYOUT;
 module_param(nowayout, int, 0);
 MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default="
        __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+/* apply or and nand masks to data read from addr and write back */
+#define SET_BITS(addr, or, nand) \
+        writel((readl(&addr) | or) & ~nand, &addr)
 static void rc32434_wdt_start(void)
 {
-        u32 val;
+        u32 or, nand;
-        if (!rc32434_wdt_device.inuse) {
-                writel(0, &wdt_reg->wtcount);
-                val = RC32434_ERR_WRE;
+        /* zero the counter before enabling */
-                writel(readl(&wdt_reg->errcs) | val, &wdt_reg->errcs);
+        writel(0, &wdt_reg->wtcount);
-                val = RC32434_WTC_EN;
+        /* don't generate a non-maskable interrupt,
-                writel(readl(&wdt_reg->wtc) | val, &wdt_reg->wtc);
+         * do a warm reset instead */
-        }
+        nand = 1 << RC32434_ERR_WNE;
-        rc32434_wdt_device.running++;
+        or = 1 << RC32434_ERR_WRE;
-}
-static void rc32434_wdt_stop(void)
+        /* reset the ERRCS timeout bit in case it's set */
-{
+        nand |= 1 << RC32434_ERR_WTO;
-        u32 val;
-        if (rc32434_wdt_device.running) {
+        SET_BITS(wdt_reg->errcs, or, nand);
-                val = ~RC32434_WTC_EN;
+        /* reset WTC timeout bit and enable WDT */
-                writel(readl(&wdt_reg->wtc) & val, &wdt_reg->wtc);
+        nand = 1 << RC32434_WTC_TO;
+        or = 1 << RC32434_WTC_EN;
-                val = ~RC32434_ERR_WRE;
+        SET_BITS(wdt_reg->wtc, or, nand);
-                writel(readl(&wdt_reg->errcs) & val, &wdt_reg->errcs);
+}
-                rc32434_wdt_device.running = 0;
+static void rc32434_wdt_stop(void)
-        }
+{
+        /* Disable WDT */
+        SET_BITS(wdt_reg->wtc, 0, 1 << RC32434_WTC_EN);
 }
-static void rc32434_wdt_set(int new_timeout)
+static int rc32434_wdt_set(int new_timeout)
 {
-        u32 cmp = new_timeout * HZ;
+        int max_to = WTCOMP2SEC((u32)-1);
-        u32 state, val;
+        if (new_timeout < 0 || new_timeout > max_to) {
+                printk(KERN_ERR KBUILD_MODNAME
+                        ": timeout value must be between 0 and %d",
+                        max_to);
+                return -EINVAL;
+        }
        timeout = new_timeout;
-        /*
+        writel(SEC2WTCOMP(timeout), &wdt_reg->wtcompare);
-         * store and disable WTC
-         */
-        state = (u32)(readl(&wdt_reg->wtc) & RC32434_WTC_EN);
-        val = ~RC32434_WTC_EN;
-        writel(readl(&wdt_reg->wtc) & val, &wdt_reg->wtc);
-        writel(0, &wdt_reg->wtcount);
-        writel(cmp, &wdt_reg->wtcompare);
-        /*
-         * restore WTC
-         */
-        writel(readl(&wdt_reg->wtc) | state, &wdt_reg);
-}
-static void rc32434_wdt_reset(void)
+        return 0;
-{
-        ticks = rc32434_wdt_device.default_ticks;
 }
-static void rc32434_wdt_update(unsigned long unused)
+static void rc32434_wdt_ping(void)
 {
-        if (rc32434_wdt_device.running)
-                ticks--;
        writel(0, &wdt_reg->wtcount);
-        if (rc32434_wdt_device.queue && ticks)
-                mod_timer(&rc32434_wdt_device.timer,
-                        jiffies + RC32434_WDT_INTERVAL);
-        else
-                complete(&rc32434_wdt_device.stop);
 }
 static int rc32434_wdt_open(struct inode *inode, struct file *file)
@@ -142,19 +127,23 @@ static int rc32434_wdt_open(struct inode *inode, struct file *file)
        if (nowayout)
                __module_get(THIS_MODULE);
+        rc32434_wdt_start();
+        rc32434_wdt_ping();
        return nonseekable_open(inode, file);
 }
 static int rc32434_wdt_release(struct inode *inode, struct file *file)
 {
-        if (expect_close && nowayout == 0) {
+        if (expect_close == 42) {
                rc32434_wdt_stop();
                printk(KERN_INFO KBUILD_MODNAME ": disabling watchdog timer\n");
                module_put(THIS_MODULE);
-        } else
+        } else {
                printk(KERN_CRIT KBUILD_MODNAME
                        ": device closed unexpectedly. WDT will not stop !\n");
+                rc32434_wdt_ping();
+        }
        clear_bit(0, &rc32434_wdt_device.inuse);
        return 0;
 }
@@ -174,10 +163,10 @@ static ssize_t rc32434_wdt_write(struct file *file, const char *data,
                                if (get_user(c, data + i))
                                        return -EFAULT;
                                if (c == 'V')
-                                        expect_close = 1;
+                                        expect_close = 42;
                        }
                }
-                rc32434_wdt_update(0);
+                rc32434_wdt_ping();
                return len;
        }
        return 0;
@@ -197,11 +186,11 @@ static long rc32434_wdt_ioctl(struct file *file, unsigned int cmd,
        };
        switch (cmd) {
        case WDIOC_KEEPALIVE:
-                rc32434_wdt_reset();
+                rc32434_wdt_ping();
                break;
        case WDIOC_GETSTATUS:
        case WDIOC_GETBOOTSTATUS:
-                value = readl(&wdt_reg->wtcount);
+                value = 0;
                if (copy_to_user(argp, &value, sizeof(int)))
                        return -EFAULT;
                break;
@@ -218,6 +207,7 @@ static long rc32434_wdt_ioctl(struct file *file, unsigned int cmd,
                        break;
                case WDIOS_DISABLECARD:
                        rc32434_wdt_stop();
+                        break;
                default:
                        return -EINVAL;
                }
@@ -225,11 +215,9 @@ static long rc32434_wdt_ioctl(struct file *file, unsigned int cmd,
        case WDIOC_SETTIMEOUT:
                if (copy_from_user(&new_timeout, argp, sizeof(int)))
                        return -EFAULT;
-                if (new_timeout < 1)
+                if (rc32434_wdt_set(new_timeout))
                        return -EINVAL;
-                if (new_timeout > MAX_TIMEOUT)
+                /* Fall through */
-                        return -EINVAL;
-                rc32434_wdt_set(new_timeout);
        case WDIOC_GETTIMEOUT:
                return copy_to_user(argp, &timeout, sizeof(int));
        default:
@@ -254,15 +242,15 @@ static struct miscdevice rc32434_wdt_miscdev = {
        .fops   = &rc32434_wdt_fops,
 };
-static char banner[] = KERN_INFO KBUILD_MODNAME
+static char banner[] __devinitdata = KERN_INFO KBUILD_MODNAME
                ": Watchdog Timer version " VERSION ", timer margin: %d sec\n";
-static int rc32434_wdt_probe(struct platform_device *pdev)
+static int __devinit rc32434_wdt_probe(struct platform_device *pdev)
 {
        int ret;
        struct resource *r;
-        r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rb500_wdt_res");
+        r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rb532_wdt_res");
        if (!r) {
                printk(KERN_ERR KBUILD_MODNAME
                        "failed to retrieve resources\n");
@@ -277,24 +265,12 @@ static int rc32434_wdt_probe(struct platform_device *pdev)
        }
        ret = misc_register(&rc32434_wdt_miscdev);
        if (ret < 0) {
                printk(KERN_ERR KBUILD_MODNAME
                        "failed to register watchdog device\n");
                goto unmap;
        }
-        init_completion(&rc32434_wdt_device.stop);
-        rc32434_wdt_device.queue = 0;
-        clear_bit(0, &rc32434_wdt_device.inuse);
-        setup_timer(&rc32434_wdt_device.timer, rc32434_wdt_update, 0L);
-        rc32434_wdt_device.default_ticks = ticks;
-        rc32434_wdt_start();
        printk(banner, timeout);
        return 0;
@@ -304,23 +280,17 @@ unmap:
        return ret;
 }
-static int rc32434_wdt_remove(struct platform_device *pdev)
+static int __devexit rc32434_wdt_remove(struct platform_device *pdev)
 {
-        if (rc32434_wdt_device.queue) {
-                rc32434_wdt_device.queue = 0;
-                wait_for_completion(&rc32434_wdt_device.stop);
-        }
        misc_deregister(&rc32434_wdt_miscdev);
        iounmap(wdt_reg);
        return 0;
 }
 static struct platform_driver rc32434_wdt = {
        .probe  = rc32434_wdt_probe,
-        .remove = rc32434_wdt_remove,
+        .remove = __devexit_p(rc32434_wdt_remove),
-        .driver = {
+        .driver = {
                .name = "rc32434_wdt",
        }
 };
diff --git a/fs/ext4/ialloc.c b/fs/ext4/ialloc.c
index f18a919be70b..627f8c3337a3 100644
--- a/fs/ext4/ialloc.c
+++ b/fs/ext4/ialloc.c
@@ -188,7 +188,7 @@ void ext4_free_inode(handle_t *handle, struct inode *inode)
        struct ext4_group_desc *gdp;
        struct ext4_super_block *es;
        struct ext4_sb_info *sbi;
-        int fatal = 0, err, count;
+        int fatal = 0, err, count, cleared;
        ext4_group_t flex_group;
        if (atomic_read(&inode->i_count) > 1) {
@@ -248,8 +248,10 @@ void ext4_free_inode(handle_t *handle, struct inode *inode)
                goto error_return;
        /* Ok, now we can actually update the inode bitmaps.. */
-        if (!ext4_clear_bit_atomic(sb_bgl_lock(sbi, block_group),
+        spin_lock(sb_bgl_lock(sbi, block_group));
-                                        bit, bitmap_bh->b_data))
+        cleared = ext4_clear_bit(bit, bitmap_bh->b_data);
+        spin_unlock(sb_bgl_lock(sbi, block_group));
+        if (!cleared)
                ext4_error(sb, "ext4_free_inode",
                           "bit already cleared for inode %lu", ino);
        else {
diff --git a/fs/squashfs/block.c b/fs/squashfs/block.c
index c837dfc2b3c6..321728f48f2d 100644
--- a/fs/squashfs/block.c
+++ b/fs/squashfs/block.c
@@ -80,7 +80,7 @@ static struct buffer_head *get_block_length(struct super_block *sb,
 * generated a larger block - this does occasionally happen with zlib).
 */
 int squashfs_read_data(struct super_block *sb, void **buffer, u64 index,
-                        int length, u64 *next_index, int srclength)
+                        int length, u64 *next_index, int srclength, int pages)
 {
        struct squashfs_sb_info *msblk = sb->s_fs_info;
        struct buffer_head **bh;
@@ -185,6 +185,14 @@ int squashfs_read_data(struct super_block *sb, void **buffer, u64 index,
                        }
                        if (msblk->stream.avail_out == 0) {
+                                if (page == pages) {
+                                        ERROR("zlib_inflate tried to "
+                                                "decompress too much data, "
+                                                "expected %d bytes.  Zlib "
+                                                "data probably corrupt\n",
+                                                srclength);
+                                        goto release_mutex;
+                                }
                                msblk->stream.next_out = buffer[page++];
                                msblk->stream.avail_out = PAGE_CACHE_SIZE;
                        }
@@ -268,7 +276,8 @@ block_release:
                put_bh(bh[k]);
 read_failure:
-        ERROR("sb_bread failed reading block 0x%llx\n", cur_index);
+        ERROR("squashfs_read_data failed to read block 0x%llx\n",
+                                        (unsigned long long) index);
        kfree(bh);
        return -EIO;
 }
diff --git a/fs/squashfs/cache.c b/fs/squashfs/cache.c
index f29eda16d25e..1c4739e33af6 100644
--- a/fs/squashfs/cache.c
+++ b/fs/squashfs/cache.c
@@ -119,7 +119,7 @@ struct squashfs_cache_entry *squashfs_cache_get(struct super_block *sb,
                        entry->length = squashfs_read_data(sb, entry->data,
                                block, length, &entry->next_index,
-                                cache->block_size);
+                                cache->block_size, cache->pages);
                        spin_lock(&cache->lock);
@@ -406,7 +406,7 @@ int squashfs_read_table(struct super_block *sb, void *buffer, u64 block,
        for (i = 0; i < pages; i++, buffer += PAGE_CACHE_SIZE)
                data[i] = buffer;
        res = squashfs_read_data(sb, data, block, length |
-                SQUASHFS_COMPRESSED_BIT_BLOCK, NULL, length);
+                SQUASHFS_COMPRESSED_BIT_BLOCK, NULL, length, pages);
        kfree(data);
        return res;
 }
diff --git a/fs/squashfs/inode.c b/fs/squashfs/inode.c
index 7a63398bb855..9101dbde39ec 100644
--- a/fs/squashfs/inode.c
+++ b/fs/squashfs/inode.c
@@ -133,7 +133,8 @@ int squashfs_read_inode(struct inode *inode, long long ino)
        type = le16_to_cpu(sqshb_ino->inode_type);
        switch (type) {
        case SQUASHFS_REG_TYPE: {
-                unsigned int frag_offset, frag_size, frag;
+                unsigned int frag_offset, frag;
+                int frag_size;
                u64 frag_blk;
                struct squashfs_reg_inode *sqsh_ino = &squashfs_ino.reg;
@@ -175,7 +176,8 @@ int squashfs_read_inode(struct inode *inode, long long ino)
                break;
        }
        case SQUASHFS_LREG_TYPE: {
-                unsigned int frag_offset, frag_size, frag;
+                unsigned int frag_offset, frag;
+                int frag_size;
                u64 frag_blk;
                struct squashfs_lreg_inode *sqsh_ino = &squashfs_ino.lreg;
diff --git a/fs/squashfs/squashfs.h b/fs/squashfs/squashfs.h
index 6b2515d027d5..0e9feb6adf7e 100644
--- a/fs/squashfs/squashfs.h
+++ b/fs/squashfs/squashfs.h
@@ -34,7 +34,7 @@ static inline struct squashfs_inode_info *squashfs_i(struct inode *inode)
 /* block.c */
 extern int squashfs_read_data(struct super_block *, void **, u64, int, u64 *,
-                                int);
+                                int, int);
 /* cache.c */
 extern struct squashfs_cache *squashfs_cache_init(char *, int, int);
diff --git a/fs/squashfs/super.c b/fs/squashfs/super.c
index 071df5b5b491..681ec0d83799 100644
--- a/fs/squashfs/super.c
+++ b/fs/squashfs/super.c
@@ -389,7 +389,7 @@ static int __init init_squashfs_fs(void)
                return err;
        }
-        printk(KERN_INFO "squashfs: version 4.0 (2009/01/03) "
+        printk(KERN_INFO "squashfs: version 4.0 (2009/01/31) "
                "Phillip Lougher\n");
        return 0;
diff --git a/include/asm-generic/vmlinux.lds.h b/include/asm-generic/vmlinux.lds.h
index 89997dfdf3d0..0e0f39be6c8b 100644
--- a/include/asm-generic/vmlinux.lds.h
+++ b/include/asm-generic/vmlinux.lds.h
@@ -98,6 +98,7 @@
        VMLINUX_SYMBOL(__stop___tracepoints) = .;                       \
        LIKELY_PROFILE()                                                \
        BRANCH_PROFILE()                                                \
+        TRACE_PRINTKS()                                                 \
        FTRACE_EVENTS()
 #define RO_DATA(align)                                                  \
@@ -108,7 +109,6 @@
                *(__vermagic)           /* Kernel version magic */      \
                *(__markers_strings)    /* Markers: strings */          \
                *(__tracepoints_strings)/* Tracepoints: strings */      \
-                TRACE_PRINTKS()                                 \
        }                                                               \
                                                                        \
        .rodata1          : AT(ADDR(.rodata1) - LOAD_OFFSET) {          \
diff --git a/include/linux/ata.h b/include/linux/ata.h
index 08a86d5cdf1b..9a061accd8b8 100644
--- a/include/linux/ata.h
+++ b/include/linux/ata.h
@@ -89,6 +89,8 @@ enum {
        ATA_ID_DLF              = 128,
        ATA_ID_CSFO             = 129,
        ATA_ID_CFA_POWER        = 160,
+        ATA_ID_CFA_KEY_MGMT     = 162,
+        ATA_ID_CFA_MODES        = 163,
        ATA_ID_ROT_SPEED        = 217,
        ATA_ID_PIO4             = (1 << 1),
diff --git a/include/linux/dmaengine.h b/include/linux/dmaengine.h
index f0413845f20e..1956c8d46d32 100644
--- a/include/linux/dmaengine.h
+++ b/include/linux/dmaengine.h
@@ -97,7 +97,6 @@ typedef struct { DECLARE_BITMAP(bits, DMA_TX_TYPE_END); } dma_cap_mask_t;
 /**
 * struct dma_chan_percpu - the per-CPU part of struct dma_chan
- * @refcount: local_t used for open-coded "bigref" counting
 * @memcpy_count: transaction counter
 * @bytes_transferred: byte counter
 */
@@ -114,9 +113,6 @@ struct dma_chan_percpu {
 * @cookie: last cookie value returned to client
 * @chan_id: channel ID for sysfs
 * @dev: class device for sysfs
- * @refcount: kref, used in "bigref" slow-mode
- * @slow_ref: indicates that the DMA channel is free
- * @rcu: the DMA channel's RCU head
 * @device_node: used to add this to the device chan list
 * @local: per-cpu pointer to a struct dma_chan_percpu
 * @client-count: how many clients are using this channel
@@ -213,8 +209,6 @@ struct dma_async_tx_descriptor {
 * @global_node: list_head for global dma_device_list
 * @cap_mask: one or more dma_capability flags
 * @max_xor: maximum number of xor sources, 0 if no capability
- * @refcount: reference count
- * @done: IO completion struct
 * @dev_id: unique device ID
 * @dev: struct device reference for dma mapping api
 * @device_alloc_chan_resources: allocate resources and return the
@@ -227,6 +221,7 @@ struct dma_async_tx_descriptor {
 * @device_prep_dma_interrupt: prepares an end of chain interrupt operation
 * @device_prep_slave_sg: prepares a slave dma operation
 * @device_terminate_all: terminate all pending operations
+ * @device_is_tx_complete: poll for transaction completion
 * @device_issue_pending: push pending transactions to hardware
 */
 struct dma_device {
diff --git a/include/linux/hdreg.h b/include/linux/hdreg.h
index c37e9241fae7..ed21bd3dbd25 100644
--- a/include/linux/hdreg.h
+++ b/include/linux/hdreg.h
@@ -511,7 +511,6 @@ struct hd_driveid {
        unsigned short  words69_70[2];  /* reserved words 69-70
                                         * future command overlap and queuing
                                         */
-        /* HDIO_GET_IDENTITY currently returns only words 0 through 70 */
        unsigned short  words71_74[4];  /* reserved words 71-74
                                         * for IDENTIFY PACKET DEVICE command
                                         */
diff --git a/include/linux/ide.h b/include/linux/ide.h
index fe235b65207e..e0cedfe9fad4 100644
--- a/include/linux/ide.h
+++ b/include/linux/ide.h
@@ -866,6 +866,7 @@ struct ide_host {
        unsigned int    n_ports;
        struct device   *dev[2];
        unsigned int    (*init_chipset)(struct pci_dev *);
+        irq_handler_t   irq_handler;
        unsigned long   host_flags;
        void            *host_priv;
        ide_hwif_t      *cur_port;      /* for hosts requiring serialization */
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index 4e726b9a71ec..7742798c9208 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -454,7 +454,10 @@ do {									\
 do {                                                                    \
        static const char *trace_printk_fmt                             \
        __attribute__((section("__trace_printk_fmt")));                 \
-        trace_printk_fmt = fmt;                                 \
+                                                                        \
+        if (!trace_printk_fmt)                                          \
+                trace_printk_fmt = fmt;                                 \
+                                                                        \
        __trace_printk_check_format(fmt, ##args);                       \
        __trace_printk(_THIS_IP_, trace_printk_fmt, ##args);            \
 } while (0)
@@ -467,7 +470,10 @@ __trace_printk(unsigned long ip, const char *fmt, ...)
 do {                                                                    \
        static const char *trace_printk_fmt                             \
        __attribute__((section("__trace_printk_fmt")));                 \
-        trace_printk_fmt = fmt;                                 \
+                                                                        \
+        if (!trace_printk_fmt)                                          \
+                trace_printk_fmt = fmt;                                 \
+                                                                        \
        __ftrace_vprintk(_THIS_IP_, trace_printk_fmt, vargs);           \
 } while (0)
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 5d87bc09a1f5..dc18b87ed722 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -275,7 +275,7 @@ enum {
         * advised to wait only for the following duration before
         * doing SRST.
         */
-        ATA_TMOUT_PMP_SRST_WAIT = 1000,
+        ATA_TMOUT_PMP_SRST_WAIT = 5000,
        /* ATA bus states */
        BUS_UNKNOWN             = 0,
@@ -530,6 +530,7 @@ struct ata_queued_cmd {
        unsigned long           flags;          /* ATA_QCFLAG_xxx */
        unsigned int            tag;
        unsigned int            n_elem;
+        unsigned int            orig_n_elem;
        int                     dma_dir;
@@ -750,7 +751,8 @@ struct ata_port {
        acpi_handle             acpi_handle;
        struct ata_acpi_gtm     __acpi_init_gtm; /* use ata_acpi_init_gtm() */
 #endif
-        u8                      sector_buf[ATA_SECT_SIZE]; /* owned by EH */
+        /* owned by EH */
+        u8                      sector_buf[ATA_SECT_SIZE] ____cacheline_aligned;
 };
 /* The following initializer overrides a method to NULL whether one of
diff --git a/include/linux/serio.h b/include/linux/serio.h
index 1bcb357a01a1..e0417e4d3f15 100644
--- a/include/linux/serio.h
+++ b/include/linux/serio.h
@@ -212,7 +212,7 @@ static inline void serio_unpin_driver(struct serio *serio)
 #define SERIO_FUJITSU   0x35
 #define SERIO_ZHENHUA   0x36
 #define SERIO_INEXIO    0x37
-#define SERIO_TOUCHIT213        0x37
+#define SERIO_TOUCHIT213        0x38
 #define SERIO_W8001     0x39
 #endif
diff --git a/kernel/softirq.c b/kernel/softirq.c
index 98dd68eea9e6..bbf6d6496f05 100644
--- a/kernel/softirq.c
+++ b/kernel/softirq.c
@@ -637,6 +637,7 @@ static int ksoftirqd(void * __bind_cpu)
                        preempt_enable_no_resched();
                        cond_resched();
                        preempt_disable();
+                        rcu_qsctr_inc((long)__bind_cpu);
                }
                preempt_enable();
                set_current_state(TASK_INTERRUPTIBLE);
diff --git a/security/smack/smack_lsm.c b/security/smack/smack_lsm.c
index 0278bc083044..e7ded1326b0f 100644
--- a/security/smack/smack_lsm.c
+++ b/security/smack/smack_lsm.c
@@ -1498,58 +1498,31 @@ static int smack_socket_post_create(struct socket *sock, int family,
 * looks for host based access restrictions
 *
 * This version will only be appropriate for really small
- * sets of single label hosts. Because of the masking
+ * sets of single label hosts.
- * it cannot shortcut out on the first match. There are
- * numerious ways to address the problem, but none of them
- * have been applied here.
 *
 * Returns the label of the far end or NULL if it's not special.
 */
 static char *smack_host_label(struct sockaddr_in *sip)
 {
        struct smk_netlbladdr *snp;
-        char *bestlabel = NULL;
        struct in_addr *siap = &sip->sin_addr;
-        struct in_addr *liap;
-        struct in_addr *miap;
-        struct in_addr bestmask;
        if (siap->s_addr == 0)
                return NULL;
-        bestmask.s_addr = 0;
        for (snp = smack_netlbladdrs; snp != NULL; snp = snp->smk_next) {
-                liap = &snp->smk_host.sin_addr;
-                miap = &snp->smk_mask;
-                /*
-                 * If the addresses match after applying the list entry mask
-                 * the entry matches the address. If it doesn't move along to
-                 * the next entry.
-                 */
-                if ((liap->s_addr & miap->s_addr) !=
-                    (siap->s_addr & miap->s_addr))
-                        continue;
                /*
-                 * If the list entry mask identifies a single address
+                 * we break after finding the first match because
-                 * it can't get any more specific.
+                 * the list is sorted from longest to shortest mask
+                 * so we have found the most specific match
                 */
-                if (miap->s_addr == 0xffffffff)
+                if ((&snp->smk_host.sin_addr)->s_addr  ==
+                        (siap->s_addr & (&snp->smk_mask)->s_addr)) {
                        return snp->smk_label;
-                /*
+                }
-                 * If the list entry mask is less specific than the best
-                 * already found this entry is uninteresting.
-                 */
-                if ((miap->s_addr | bestmask.s_addr) == bestmask.s_addr)
-                        continue;
-                /*
-                 * This is better than any entry found so far.
-                 */
-                bestmask.s_addr = miap->s_addr;
-                bestlabel = snp->smk_label;
        }
-        return bestlabel;
+        return NULL;
 }
 /**
diff --git a/security/smack/smackfs.c b/security/smack/smackfs.c
index 8e42800878f4..51f0efc50dab 100644
--- a/security/smack/smackfs.c
+++ b/security/smack/smackfs.c
@@ -650,10 +650,6 @@ static void *netlbladdr_seq_next(struct seq_file *s, void *v, loff_t *pos)
        return skp;
 }
-/*
-#define BEMASK  0x80000000
-*/
-#define BEMASK  0x00000001
 #define BEBITS  (sizeof(__be32) * 8)
 /*
@@ -663,12 +659,10 @@ static int netlbladdr_seq_show(struct seq_file *s, void *v)
 {
        struct smk_netlbladdr *skp = (struct smk_netlbladdr *) v;
        unsigned char *hp = (char *) &skp->smk_host.sin_addr.s_addr;
-        __be32 bebits;
+        int maskn;
-        int maskn = 0;
+        u32 temp_mask = be32_to_cpu(skp->smk_mask.s_addr);
-        for (bebits = BEMASK; bebits != 0; maskn++, bebits <<= 1)
+        for (maskn = 0; temp_mask; temp_mask <<= 1, maskn++);
-                if ((skp->smk_mask.s_addr & bebits) == 0)
-                        break;
        seq_printf(s, "%u.%u.%u.%u/%d %s\n",
                hp[0], hp[1], hp[2], hp[3], maskn, skp->smk_label);
@@ -702,6 +696,42 @@ static int smk_open_netlbladdr(struct inode *inode, struct file *file)
 }
 /**
+ * smk_netlbladdr_insert
+ * @new : netlabel to insert
+ *
+ * This helper insert netlabel in the smack_netlbladdrs list
+ * sorted by netmask length (longest to smallest)
+ */
+static void smk_netlbladdr_insert(struct smk_netlbladdr *new)
+{
+        struct smk_netlbladdr *m;
+        if (smack_netlbladdrs == NULL) {
+                smack_netlbladdrs = new;
+                return;
+        }
+        /* the comparison '>' is a bit hacky, but works */
+        if (new->smk_mask.s_addr > smack_netlbladdrs->smk_mask.s_addr) {
+                new->smk_next = smack_netlbladdrs;
+                smack_netlbladdrs = new;
+                return;
+        }
+        for (m = smack_netlbladdrs; m != NULL; m = m->smk_next) {
+                if (m->smk_next == NULL) {
+                        m->smk_next = new;
+                        return;
+                }
+                if (new->smk_mask.s_addr > m->smk_next->smk_mask.s_addr) {
+                        new->smk_next = m->smk_next;
+                        m->smk_next = new;
+                        return;
+                }
+        }
+}
+/**
 * smk_write_netlbladdr - write() for /smack/netlabel
 * @filp: file pointer, not actually used
 * @buf: where to get the data from
@@ -724,8 +754,9 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
        struct netlbl_audit audit_info;
        struct in_addr mask;
        unsigned int m;
-        __be32 bebits = BEMASK;
+        u32 mask_bits = (1<<31);
        __be32 nsa;
+        u32 temp_mask;
        /*
         * Must have privilege.
@@ -761,10 +792,13 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
        if (sp == NULL)
                return -EINVAL;
-        for (mask.s_addr = 0; m > 0; m--) {
+        for (temp_mask = 0; m > 0; m--) {
-                mask.s_addr |= bebits;
+                temp_mask |= mask_bits;
-                bebits <<= 1;
+                mask_bits >>= 1;
        }
+        mask.s_addr = cpu_to_be32(temp_mask);
+        newname.sin_addr.s_addr &= mask.s_addr;
        /*
         * Only allow one writer at a time. Writes should be
         * quite rare and small in any case.
@@ -772,6 +806,7 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
        mutex_lock(&smk_netlbladdr_lock);
        nsa = newname.sin_addr.s_addr;
+        /* try to find if the prefix is already in the list */
        for (skp = smack_netlbladdrs; skp != NULL; skp = skp->smk_next)
                if (skp->smk_host.sin_addr.s_addr == nsa &&
                    skp->smk_mask.s_addr == mask.s_addr)
@@ -787,9 +822,8 @@ static ssize_t smk_write_netlbladdr(struct file *file, const char __user *buf,
                        rc = 0;
                        skp->smk_host.sin_addr.s_addr = newname.sin_addr.s_addr;
                        skp->smk_mask.s_addr = mask.s_addr;
-                        skp->smk_next = smack_netlbladdrs;
                        skp->smk_label = sp;
-                        smack_netlbladdrs = skp;
+                        smk_netlbladdr_insert(skp);
                }
        } else {
                rc = netlbl_cfg_unlbl_static_del(&init_net, NULL,
diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index 3bc427645da8..6094344fb223 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -1207,7 +1207,7 @@ static const char *slave_vols[] = {
        "LFE Playback Volume",
        "Side Playback Volume",
        "Headphone Playback Volume",
-        "Headphone Playback Volume",
+        "Headphone2 Playback Volume",
        "Speaker Playback Volume",
        "External Speaker Playback Volume",
        "Speaker2 Playback Volume",
@@ -1221,7 +1221,7 @@ static const char *slave_sws[] = {
        "LFE Playback Switch",
        "Side Playback Switch",
        "Headphone Playback Switch",
-        "Headphone Playback Switch",
+        "Headphone2 Playback Switch",
        "Speaker Playback Switch",
        "External Speaker Playback Switch",
        "Speaker2 Playback Switch",
@@ -3516,6 +3516,7 @@ static int stac92xx_parse_auto_config(struct hda_codec *codec, hda_nid_t dig_out
        if (! spec->autocfg.line_outs)
                return 0; /* can't find valid pin config */
+#if 0 /* FIXME: temporarily disabled */
        /* If we have no real line-out pin and multiple hp-outs, HPs should
         * be set up as multi-channel outputs.
         */
@@ -3535,6 +3536,7 @@ static int stac92xx_parse_auto_config(struct hda_codec *codec, hda_nid_t dig_out
                spec->autocfg.line_out_type = AUTO_PIN_HP_OUT;
                spec->autocfg.hp_outs = 0;
        }
+#endif /* FIXME: temporarily disabled */
        if (spec->autocfg.mono_out_pin) {
                int dir = get_wcaps(codec, spec->autocfg.mono_out_pin) &
                        (AC_WCAP_OUT_AMP | AC_WCAP_IN_AMP);