aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--Documentation/spi/pxa2xx234
-rw-r--r--drivers/spi/Kconfig8
-rw-r--r--drivers/spi/Makefile1
-rw-r--r--drivers/spi/pxa2xx_spi.c1399
-rw-r--r--include/asm-arm/arch-pxa/pxa2xx_spi.h68
5 files changed, 1710 insertions, 0 deletions
diff --git a/Documentation/spi/pxa2xx b/Documentation/spi/pxa2xx
new file mode 100644
index 000000000000..9c45f3df2e18
--- /dev/null
+++ b/Documentation/spi/pxa2xx
@@ -0,0 +1,234 @@
1PXA2xx SPI on SSP driver HOWTO
2===================================================
3This a mini howto on the pxa2xx_spi driver. The driver turns a PXA2xx
4synchronous serial port into a SPI master controller
5(see Documentation/spi/spi_summary). The driver has the following features
6
7- Support for any PXA2xx SSP
8- SSP PIO and SSP DMA data transfers.
9- External and Internal (SSPFRM) chip selects.
10- Per slave device (chip) configuration.
11- Full suspend, freeze, resume support.
12
13The driver is built around a "spi_message" fifo serviced by workqueue and a
14tasklet. The workqueue, "pump_messages", drives message fifo and the tasklet
15(pump_transfer) is responsible for queuing SPI transactions and setting up and
16launching the dma/interrupt driven transfers.
17
18Declaring PXA2xx Master Controllers
19-----------------------------------
20Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a
21"platform device". The master configuration is passed to the driver via a table
22found in include/asm-arm/arch-pxa/pxa2xx_spi.h:
23
24struct pxa2xx_spi_master {
25 enum pxa_ssp_type ssp_type;
26 u32 clock_enable;
27 u16 num_chipselect;
28 u8 enable_dma;
29};
30
31The "pxa2xx_spi_master.ssp_type" field must have a value between 1 and 3 and
32informs the driver which features a particular SSP supports.
33
34The "pxa2xx_spi_master.clock_enable" field is used to enable/disable the
35corresponding SSP peripheral block in the "Clock Enable Register (CKEN"). See
36the "PXA2xx Developer Manual" section "Clocks and Power Management".
37
38The "pxa2xx_spi_master.num_chipselect" field is used to determine the number of
39slave device (chips) attached to this SPI master.
40
41The "pxa2xx_spi_master.enable_dma" field informs the driver that SSP DMA should
42be used. This caused the driver to acquire two DMA channels: rx_channel and
43tx_channel. The rx_channel has a higher DMA service priority the tx_channel.
44See the "PXA2xx Developer Manual" section "DMA Controller".
45
46NSSP MASTER SAMPLE
47------------------
48Below is a sample configuration using the PXA255 NSSP.
49
50static struct resource pxa_spi_nssp_resources[] = {
51 [0] = {
52 .start = __PREG(SSCR0_P(2)), /* Start address of NSSP */
53 .end = __PREG(SSCR0_P(2)) + 0x2c, /* Range of registers */
54 .flags = IORESOURCE_MEM,
55 },
56 [1] = {
57 .start = IRQ_NSSP, /* NSSP IRQ */
58 .end = IRQ_NSSP,
59 .flags = IORESOURCE_IRQ,
60 },
61};
62
63static struct pxa2xx_spi_master pxa_nssp_master_info = {
64 .ssp_type = PXA25x_NSSP, /* Type of SSP */
65 .clock_enable = CKEN9_NSSP, /* NSSP Peripheral clock */
66 .num_chipselect = 1, /* Matches the number of chips attached to NSSP */
67 .enable_dma = 1, /* Enables NSSP DMA */
68};
69
70static struct platform_device pxa_spi_nssp = {
71 .name = "pxa2xx-spi", /* MUST BE THIS VALUE, so device match driver */
72 .id = 2, /* Bus number, MUST MATCH SSP number 1..n */
73 .resource = pxa_spi_nssp_resources,
74 .num_resources = ARRAY_SIZE(pxa_spi_nssp_resources),
75 .dev = {
76 .platform_data = &pxa_nssp_master_info, /* Passed to driver */
77 },
78};
79
80static struct platform_device *devices[] __initdata = {
81 &pxa_spi_nssp,
82};
83
84static void __init board_init(void)
85{
86 (void)platform_add_device(devices, ARRAY_SIZE(devices));
87}
88
89Declaring Slave Devices
90-----------------------
91Typically each SPI slave (chip) is defined in the arch/.../mach-*/board-*.c
92using the "spi_board_info" structure found in "linux/spi/spi.h". See
93"Documentation/spi/spi_summary" for additional information.
94
95Each slave device attached to the PXA must provide slave specific configuration
96information via the structure "pxa2xx_spi_chip" found in
97"include/asm-arm/arch-pxa/pxa2xx_spi.h". The pxa2xx_spi master controller driver
98will uses the configuration whenever the driver communicates with the slave
99device.
100
101struct pxa2xx_spi_chip {
102 u8 tx_threshold;
103 u8 rx_threshold;
104 u8 dma_burst_size;
105 u32 timeout_microsecs;
106 u8 enable_loopback;
107 void (*cs_control)(u32 command);
108};
109
110The "pxa2xx_spi_chip.tx_threshold" and "pxa2xx_spi_chip.rx_threshold" fields are
111used to configure the SSP hardware fifo. These fields are critical to the
112performance of pxa2xx_spi driver and misconfiguration will result in rx
113fifo overruns (especially in PIO mode transfers). Good default values are
114
115 .tx_threshold = 12,
116 .rx_threshold = 4,
117
118The "pxa2xx_spi_chip.dma_burst_size" field is used to configure PXA2xx DMA
119engine and is related the "spi_device.bits_per_word" field. Read and understand
120the PXA2xx "Developer Manual" sections on the DMA controller and SSP Controllers
121to determine the correct value. An SSP configured for byte-wide transfers would
122use a value of 8.
123
124The "pxa2xx_spi_chip.timeout_microsecs" fields is used to efficiently handle
125trailing bytes in the SSP receiver fifo. The correct value for this field is
126dependent on the SPI bus speed ("spi_board_info.max_speed_hz") and the specific
127slave device. Please note the the PXA2xx SSP 1 does not support trailing byte
128timeouts and must busy-wait any trailing bytes.
129
130The "pxa2xx_spi_chip.enable_loopback" field is used to place the SSP porting
131into internal loopback mode. In this mode the SSP controller internally
132connects the SSPTX pin the the SSPRX pin. This is useful for initial setup
133testing.
134
135The "pxa2xx_spi_chip.cs_control" field is used to point to a board specific
136function for asserting/deasserting a slave device chip select. If the field is
137NULL, the pxa2xx_spi master controller driver assumes that the SSP port is
138configured to use SSPFRM instead.
139
140NSSP SALVE SAMPLE
141-----------------
142The pxa2xx_spi_chip structure is passed to the pxa2xx_spi driver in the
143"spi_board_info.controller_data" field. Below is a sample configuration using
144the PXA255 NSSP.
145
146/* Chip Select control for the CS8415A SPI slave device */
147static void cs8415a_cs_control(u32 command)
148{
149 if (command & PXA2XX_CS_ASSERT)
150 GPCR(2) = GPIO_bit(2);
151 else
152 GPSR(2) = GPIO_bit(2);
153}
154
155/* Chip Select control for the CS8405A SPI slave device */
156static void cs8405a_cs_control(u32 command)
157{
158 if (command & PXA2XX_CS_ASSERT)
159 GPCR(3) = GPIO_bit(3);
160 else
161 GPSR(3) = GPIO_bit(3);
162}
163
164static struct pxa2xx_spi_chip cs8415a_chip_info = {
165 .tx_threshold = 12, /* SSP hardward FIFO threshold */
166 .rx_threshold = 4, /* SSP hardward FIFO threshold */
167 .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
168 .timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */
169 .cs_control = cs8415a_cs_control, /* Use external chip select */
170};
171
172static struct pxa2xx_spi_chip cs8405a_chip_info = {
173 .tx_threshold = 12, /* SSP hardward FIFO threshold */
174 .rx_threshold = 4, /* SSP hardward FIFO threshold */
175 .dma_burst_size = 8, /* Byte wide transfers used so 8 byte bursts */
176 .timeout_microsecs = 64, /* Wait at least 64usec to handle trailing */
177 .cs_control = cs8405a_cs_control, /* Use external chip select */
178};
179
180static struct spi_board_info streetracer_spi_board_info[] __initdata = {
181 {
182 .modalias = "cs8415a", /* Name of spi_driver for this device */
183 .max_speed_hz = 3686400, /* Run SSP as fast a possbile */
184 .bus_num = 2, /* Framework bus number */
185 .chip_select = 0, /* Framework chip select */
186 .platform_data = NULL; /* No spi_driver specific config */
187 .controller_data = &cs8415a_chip_info, /* Master chip config */
188 .irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */
189 },
190 {
191 .modalias = "cs8405a", /* Name of spi_driver for this device */
192 .max_speed_hz = 3686400, /* Run SSP as fast a possbile */
193 .bus_num = 2, /* Framework bus number */
194 .chip_select = 1, /* Framework chip select */
195 .controller_data = &cs8405a_chip_info, /* Master chip config */
196 .irq = STREETRACER_APCI_IRQ, /* Slave device interrupt */
197 },
198};
199
200static void __init streetracer_init(void)
201{
202 spi_register_board_info(streetracer_spi_board_info,
203 ARRAY_SIZE(streetracer_spi_board_info));
204}
205
206
207DMA and PIO I/O Support
208-----------------------
209The pxa2xx_spi driver support both DMA and interrupt driven PIO message
210transfers. The driver defaults to PIO mode and DMA transfers must enabled by
211setting the "enable_dma" flag in the "pxa2xx_spi_master" structure and and
212ensuring that the "pxa2xx_spi_chip.dma_burst_size" field is non-zero. The DMA
213mode support both coherent and stream based DMA mappings.
214
215The following logic is used to determine the type of I/O to be used on
216a per "spi_transfer" basis:
217
218if !enable_dma or dma_burst_size == 0 then
219 always use PIO transfers
220
221if spi_message.is_dma_mapped and rx_dma_buf != 0 and tx_dma_buf != 0 then
222 use coherent DMA mode
223
224if rx_buf and tx_buf are aligned on 8 byte boundary then
225 use streaming DMA mode
226
227otherwise
228 use PIO transfer
229
230THANKS TO
231---------
232
233David Brownell and others for mentoring the development of this driver.
234
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 7a75faeb0526..9ce1d01469b1 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -75,6 +75,14 @@ config SPI_BUTTERFLY
75 inexpensive battery powered microcontroller evaluation board. 75 inexpensive battery powered microcontroller evaluation board.
76 This same cable can be used to flash new firmware. 76 This same cable can be used to flash new firmware.
77 77
78config SPI_PXA2XX
79 tristate "PXA2xx SSP SPI master"
80 depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL
81 help
82 This enables using a PXA2xx SSP port as a SPI master controller.
83 The driver can be configured to use any SSP port and additional
84 documentation can be found a Documentation/spi/pxa2xx.
85
78# 86#
79# Add new SPI master controllers in alphabetical order above this line 87# Add new SPI master controllers in alphabetical order above this line
80# 88#
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index c2c87e845abf..1bca5f95de25 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_SPI_MASTER) += spi.o
13# SPI master controller drivers (bus) 13# SPI master controller drivers (bus)
14obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o 14obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
15obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o 15obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
16obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o
16# ... add above this line ... 17# ... add above this line ...
17 18
18# SPI protocol drivers (device/link on bus) 19# SPI protocol drivers (device/link on bus)
diff --git a/drivers/spi/pxa2xx_spi.c b/drivers/spi/pxa2xx_spi.c
new file mode 100644
index 000000000000..913e1aff0235
--- /dev/null
+++ b/drivers/spi/pxa2xx_spi.c
@@ -0,0 +1,1399 @@
1/*
2 * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
3 *
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License as published by
6 * the Free Software Foundation; either version 2 of the License, or
7 * (at your option) any later version.
8 *
9 * This program is distributed in the hope that it will be useful,
10 * but WITHOUT ANY WARRANTY; without even the implied warranty of
11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
12 * GNU General Public License for more details.
13 *
14 * You should have received a copy of the GNU General Public License
15 * along with this program; if not, write to the Free Software
16 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
17 */
18
19#include <linux/init.h>
20#include <linux/module.h>
21#include <linux/device.h>
22#include <linux/ioport.h>
23#include <linux/errno.h>
24#include <linux/interrupt.h>
25#include <linux/platform_device.h>
26#include <linux/dma-mapping.h>
27#include <linux/spi/spi.h>
28#include <linux/workqueue.h>
29#include <linux/errno.h>
30#include <linux/delay.h>
31
32#include <asm/io.h>
33#include <asm/irq.h>
34#include <asm/hardware.h>
35#include <asm/delay.h>
36#include <asm/dma.h>
37
38#include <asm/arch/hardware.h>
39#include <asm/arch/pxa-regs.h>
40#include <asm/arch/pxa2xx_spi.h>
41
42MODULE_AUTHOR("Stephen Street");
43MODULE_DESCRIPTION("PXA2xx SSP SPI Contoller");
44MODULE_LICENSE("GPL");
45
46#define MAX_BUSES 3
47
48#define DMA_INT_MASK (DCSR_ENDINTR | DCSR_STARTINTR | DCSR_BUSERR)
49#define RESET_DMA_CHANNEL (DCSR_NODESC | DMA_INT_MASK)
50#define IS_DMA_ALIGNED(x) (((u32)(x)&0x07)==0)
51
52#define DEFINE_SSP_REG(reg, off) \
53static inline u32 read_##reg(void *p) { return __raw_readl(p + (off)); } \
54static inline void write_##reg(u32 v, void *p) { __raw_writel(v, p + (off)); }
55
56DEFINE_SSP_REG(SSCR0, 0x00)
57DEFINE_SSP_REG(SSCR1, 0x04)
58DEFINE_SSP_REG(SSSR, 0x08)
59DEFINE_SSP_REG(SSITR, 0x0c)
60DEFINE_SSP_REG(SSDR, 0x10)
61DEFINE_SSP_REG(SSTO, 0x28)
62DEFINE_SSP_REG(SSPSP, 0x2c)
63
64#define START_STATE ((void*)0)
65#define RUNNING_STATE ((void*)1)
66#define DONE_STATE ((void*)2)
67#define ERROR_STATE ((void*)-1)
68
69#define QUEUE_RUNNING 0
70#define QUEUE_STOPPED 1
71
72struct driver_data {
73 /* Driver model hookup */
74 struct platform_device *pdev;
75
76 /* SPI framework hookup */
77 enum pxa_ssp_type ssp_type;
78 struct spi_master *master;
79
80 /* PXA hookup */
81 struct pxa2xx_spi_master *master_info;
82
83 /* DMA setup stuff */
84 int rx_channel;
85 int tx_channel;
86 u32 *null_dma_buf;
87
88 /* SSP register addresses */
89 void *ioaddr;
90 u32 ssdr_physical;
91
92 /* SSP masks*/
93 u32 dma_cr1;
94 u32 int_cr1;
95 u32 clear_sr;
96 u32 mask_sr;
97
98 /* Driver message queue */
99 struct workqueue_struct *workqueue;
100 struct work_struct pump_messages;
101 spinlock_t lock;
102 struct list_head queue;
103 int busy;
104 int run;
105
106 /* Message Transfer pump */
107 struct tasklet_struct pump_transfers;
108
109 /* Current message transfer state info */
110 struct spi_message* cur_msg;
111 struct spi_transfer* cur_transfer;
112 struct chip_data *cur_chip;
113 size_t len;
114 void *tx;
115 void *tx_end;
116 void *rx;
117 void *rx_end;
118 int dma_mapped;
119 dma_addr_t rx_dma;
120 dma_addr_t tx_dma;
121 size_t rx_map_len;
122 size_t tx_map_len;
123 int cs_change;
124 void (*write)(struct driver_data *drv_data);
125 void (*read)(struct driver_data *drv_data);
126 irqreturn_t (*transfer_handler)(struct driver_data *drv_data);
127 void (*cs_control)(u32 command);
128};
129
130struct chip_data {
131 u32 cr0;
132 u32 cr1;
133 u32 to;
134 u32 psp;
135 u32 timeout;
136 u8 n_bytes;
137 u32 dma_width;
138 u32 dma_burst_size;
139 u32 threshold;
140 u32 dma_threshold;
141 u8 enable_dma;
142 void (*write)(struct driver_data *drv_data);
143 void (*read)(struct driver_data *drv_data);
144 void (*cs_control)(u32 command);
145};
146
147static void pump_messages(void *data);
148
149static int flush(struct driver_data *drv_data)
150{
151 unsigned long limit = loops_per_jiffy << 1;
152
153 void *reg = drv_data->ioaddr;
154
155 do {
156 while (read_SSSR(reg) & SSSR_RNE) {
157 read_SSDR(reg);
158 }
159 } while ((read_SSSR(reg) & SSSR_BSY) && limit--);
160 write_SSSR(SSSR_ROR, reg);
161
162 return limit;
163}
164
165static void restore_state(struct driver_data *drv_data)
166{
167 void *reg = drv_data->ioaddr;
168
169 /* Clear status and disable clock */
170 write_SSSR(drv_data->clear_sr, reg);
171 write_SSCR0(drv_data->cur_chip->cr0 & ~SSCR0_SSE, reg);
172
173 /* Load the registers */
174 write_SSCR1(drv_data->cur_chip->cr1, reg);
175 write_SSCR0(drv_data->cur_chip->cr0, reg);
176 if (drv_data->ssp_type != PXA25x_SSP) {
177 write_SSTO(0, reg);
178 write_SSPSP(drv_data->cur_chip->psp, reg);
179 }
180}
181
182static void null_cs_control(u32 command)
183{
184}
185
186static void null_writer(struct driver_data *drv_data)
187{
188 void *reg = drv_data->ioaddr;
189 u8 n_bytes = drv_data->cur_chip->n_bytes;
190
191 while ((read_SSSR(reg) & SSSR_TNF)
192 && (drv_data->tx < drv_data->tx_end)) {
193 write_SSDR(0, reg);
194 drv_data->tx += n_bytes;
195 }
196}
197
198static void null_reader(struct driver_data *drv_data)
199{
200 void *reg = drv_data->ioaddr;
201 u8 n_bytes = drv_data->cur_chip->n_bytes;
202
203 while ((read_SSSR(reg) & SSSR_RNE)
204 && (drv_data->rx < drv_data->rx_end)) {
205 read_SSDR(reg);
206 drv_data->rx += n_bytes;
207 }
208}
209
210static void u8_writer(struct driver_data *drv_data)
211{
212 void *reg = drv_data->ioaddr;
213
214 while ((read_SSSR(reg) & SSSR_TNF)
215 && (drv_data->tx < drv_data->tx_end)) {
216 write_SSDR(*(u8 *)(drv_data->tx), reg);
217 ++drv_data->tx;
218 }
219}
220
221static void u8_reader(struct driver_data *drv_data)
222{
223 void *reg = drv_data->ioaddr;
224
225 while ((read_SSSR(reg) & SSSR_RNE)
226 && (drv_data->rx < drv_data->rx_end)) {
227 *(u8 *)(drv_data->rx) = read_SSDR(reg);
228 ++drv_data->rx;
229 }
230}
231
232static void u16_writer(struct driver_data *drv_data)
233{
234 void *reg = drv_data->ioaddr;
235
236 while ((read_SSSR(reg) & SSSR_TNF)
237 && (drv_data->tx < drv_data->tx_end)) {
238 write_SSDR(*(u16 *)(drv_data->tx), reg);
239 drv_data->tx += 2;
240 }
241}
242
243static void u16_reader(struct driver_data *drv_data)
244{
245 void *reg = drv_data->ioaddr;
246
247 while ((read_SSSR(reg) & SSSR_RNE)
248 && (drv_data->rx < drv_data->rx_end)) {
249 *(u16 *)(drv_data->rx) = read_SSDR(reg);
250 drv_data->rx += 2;
251 }
252}
253static void u32_writer(struct driver_data *drv_data)
254{
255 void *reg = drv_data->ioaddr;
256
257 while ((read_SSSR(reg) & SSSR_TNF)
258 && (drv_data->tx < drv_data->tx_end)) {
259 write_SSDR(*(u16 *)(drv_data->tx), reg);
260 drv_data->tx += 4;
261 }
262}
263
264static void u32_reader(struct driver_data *drv_data)
265{
266 void *reg = drv_data->ioaddr;
267
268 while ((read_SSSR(reg) & SSSR_RNE)
269 && (drv_data->rx < drv_data->rx_end)) {
270 *(u32 *)(drv_data->rx) = read_SSDR(reg);
271 drv_data->rx += 4;
272 }
273}
274
275static void *next_transfer(struct driver_data *drv_data)
276{
277 struct spi_message *msg = drv_data->cur_msg;
278 struct spi_transfer *trans = drv_data->cur_transfer;
279
280 /* Move to next transfer */
281 if (trans->transfer_list.next != &msg->transfers) {
282 drv_data->cur_transfer =
283 list_entry(trans->transfer_list.next,
284 struct spi_transfer,
285 transfer_list);
286 return RUNNING_STATE;
287 } else
288 return DONE_STATE;
289}
290
291static int map_dma_buffers(struct driver_data *drv_data)
292{
293 struct spi_message *msg = drv_data->cur_msg;
294 struct device *dev = &msg->spi->dev;
295
296 if (!drv_data->cur_chip->enable_dma)
297 return 0;
298
299 if (msg->is_dma_mapped)
300 return drv_data->rx_dma && drv_data->tx_dma;
301
302 if (!IS_DMA_ALIGNED(drv_data->rx) || !IS_DMA_ALIGNED(drv_data->tx))
303 return 0;
304
305 /* Modify setup if rx buffer is null */
306 if (drv_data->rx == NULL) {
307 *drv_data->null_dma_buf = 0;
308 drv_data->rx = drv_data->null_dma_buf;
309 drv_data->rx_map_len = 4;
310 } else
311 drv_data->rx_map_len = drv_data->len;
312
313
314 /* Modify setup if tx buffer is null */
315 if (drv_data->tx == NULL) {
316 *drv_data->null_dma_buf = 0;
317 drv_data->tx = drv_data->null_dma_buf;
318 drv_data->tx_map_len = 4;
319 } else
320 drv_data->tx_map_len = drv_data->len;
321
322 /* Stream map the rx buffer */
323 drv_data->rx_dma = dma_map_single(dev, drv_data->rx,
324 drv_data->rx_map_len,
325 DMA_FROM_DEVICE);
326 if (dma_mapping_error(drv_data->rx_dma))
327 return 0;
328
329 /* Stream map the tx buffer */
330 drv_data->tx_dma = dma_map_single(dev, drv_data->tx,
331 drv_data->tx_map_len,
332 DMA_TO_DEVICE);
333
334 if (dma_mapping_error(drv_data->tx_dma)) {
335 dma_unmap_single(dev, drv_data->rx_dma,
336 drv_data->rx_map_len, DMA_FROM_DEVICE);
337 return 0;
338 }
339
340 return 1;
341}
342
343static void unmap_dma_buffers(struct driver_data *drv_data)
344{
345 struct device *dev;
346
347 if (!drv_data->dma_mapped)
348 return;
349
350 if (!drv_data->cur_msg->is_dma_mapped) {
351 dev = &drv_data->cur_msg->spi->dev;
352 dma_unmap_single(dev, drv_data->rx_dma,
353 drv_data->rx_map_len, DMA_FROM_DEVICE);
354 dma_unmap_single(dev, drv_data->tx_dma,
355 drv_data->tx_map_len, DMA_TO_DEVICE);
356 }
357
358 drv_data->dma_mapped = 0;
359}
360
361/* caller already set message->status; dma and pio irqs are blocked */
362static void giveback(struct spi_message *message, struct driver_data *drv_data)
363{
364 struct spi_transfer* last_transfer;
365
366 last_transfer = list_entry(message->transfers.prev,
367 struct spi_transfer,
368 transfer_list);
369
370 if (!last_transfer->cs_change)
371 drv_data->cs_control(PXA2XX_CS_DEASSERT);
372
373 message->state = NULL;
374 if (message->complete)
375 message->complete(message->context);
376
377 drv_data->cur_msg = NULL;
378 drv_data->cur_transfer = NULL;
379 drv_data->cur_chip = NULL;
380 queue_work(drv_data->workqueue, &drv_data->pump_messages);
381}
382
383static int wait_ssp_rx_stall(void *ioaddr)
384{
385 unsigned long limit = loops_per_jiffy << 1;
386
387 while ((read_SSSR(ioaddr) & SSSR_BSY) && limit--)
388 cpu_relax();
389
390 return limit;
391}
392
393static int wait_dma_channel_stop(int channel)
394{
395 unsigned long limit = loops_per_jiffy << 1;
396
397 while (!(DCSR(channel) & DCSR_STOPSTATE) && limit--)
398 cpu_relax();
399
400 return limit;
401}
402
403static void dma_handler(int channel, void *data, struct pt_regs *regs)
404{
405 struct driver_data *drv_data = data;
406 struct spi_message *msg = drv_data->cur_msg;
407 void *reg = drv_data->ioaddr;
408 u32 irq_status = DCSR(channel) & DMA_INT_MASK;
409 u32 trailing_sssr = 0;
410
411 if (irq_status & DCSR_BUSERR) {
412
413 /* Disable interrupts, clear status and reset DMA */
414 if (drv_data->ssp_type != PXA25x_SSP)
415 write_SSTO(0, reg);
416 write_SSSR(drv_data->clear_sr, reg);
417 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
418 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
419 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
420
421 if (flush(drv_data) == 0)
422 dev_err(&drv_data->pdev->dev,
423 "dma_handler: flush fail\n");
424
425 unmap_dma_buffers(drv_data);
426
427 if (channel == drv_data->tx_channel)
428 dev_err(&drv_data->pdev->dev,
429 "dma_handler: bad bus address on "
430 "tx channel %d, source %x target = %x\n",
431 channel, DSADR(channel), DTADR(channel));
432 else
433 dev_err(&drv_data->pdev->dev,
434 "dma_handler: bad bus address on "
435 "rx channel %d, source %x target = %x\n",
436 channel, DSADR(channel), DTADR(channel));
437
438 msg->state = ERROR_STATE;
439 tasklet_schedule(&drv_data->pump_transfers);
440 }
441
442 /* PXA255x_SSP has no timeout interrupt, wait for tailing bytes */
443 if ((drv_data->ssp_type == PXA25x_SSP)
444 && (channel == drv_data->tx_channel)
445 && (irq_status & DCSR_ENDINTR)) {
446
447 /* Wait for rx to stall */
448 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
449 dev_err(&drv_data->pdev->dev,
450 "dma_handler: ssp rx stall failed\n");
451
452 /* Clear and disable interrupts on SSP and DMA channels*/
453 write_SSSR(drv_data->clear_sr, reg);
454 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
455 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
456 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
457 if (wait_dma_channel_stop(drv_data->rx_channel) == 0)
458 dev_err(&drv_data->pdev->dev,
459 "dma_handler: dma rx channel stop failed\n");
460
461 unmap_dma_buffers(drv_data);
462
463 /* Read trailing bytes */
464 /* Calculate number of trailing bytes, read them */
465 trailing_sssr = read_SSSR(reg);
466 if ((trailing_sssr & 0xf008) != 0xf000) {
467 drv_data->rx = drv_data->rx_end -
468 (((trailing_sssr >> 12) & 0x0f) + 1);
469 drv_data->read(drv_data);
470 }
471 msg->actual_length += drv_data->len;
472
473 /* Release chip select if requested, transfer delays are
474 * handled in pump_transfers */
475 if (drv_data->cs_change)
476 drv_data->cs_control(PXA2XX_CS_DEASSERT);
477
478 /* Move to next transfer */
479 msg->state = next_transfer(drv_data);
480
481 /* Schedule transfer tasklet */
482 tasklet_schedule(&drv_data->pump_transfers);
483 }
484}
485
486static irqreturn_t dma_transfer(struct driver_data *drv_data)
487{
488 u32 irq_status;
489 u32 trailing_sssr = 0;
490 struct spi_message *msg = drv_data->cur_msg;
491 void *reg = drv_data->ioaddr;
492
493 irq_status = read_SSSR(reg) & drv_data->mask_sr;
494 if (irq_status & SSSR_ROR) {
495 /* Clear and disable interrupts on SSP and DMA channels*/
496 if (drv_data->ssp_type != PXA25x_SSP)
497 write_SSTO(0, reg);
498 write_SSSR(drv_data->clear_sr, reg);
499 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
500 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
501 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
502 unmap_dma_buffers(drv_data);
503
504 if (flush(drv_data) == 0)
505 dev_err(&drv_data->pdev->dev,
506 "dma_transfer: flush fail\n");
507
508 dev_warn(&drv_data->pdev->dev, "dma_transfer: fifo overun\n");
509
510 drv_data->cur_msg->state = ERROR_STATE;
511 tasklet_schedule(&drv_data->pump_transfers);
512
513 return IRQ_HANDLED;
514 }
515
516 /* Check for false positive timeout */
517 if ((irq_status & SSSR_TINT) && DCSR(drv_data->tx_channel) & DCSR_RUN) {
518 write_SSSR(SSSR_TINT, reg);
519 return IRQ_HANDLED;
520 }
521
522 if (irq_status & SSSR_TINT || drv_data->rx == drv_data->rx_end) {
523
524 /* Clear and disable interrupts on SSP and DMA channels*/
525 if (drv_data->ssp_type != PXA25x_SSP)
526 write_SSTO(0, reg);
527 write_SSSR(drv_data->clear_sr, reg);
528 write_SSCR1(read_SSCR1(reg) & ~drv_data->dma_cr1, reg);
529 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
530 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
531
532 if (wait_dma_channel_stop(drv_data->rx_channel) == 0)
533 dev_err(&drv_data->pdev->dev,
534 "dma_transfer: dma rx channel stop failed\n");
535
536 if (wait_ssp_rx_stall(drv_data->ioaddr) == 0)
537 dev_err(&drv_data->pdev->dev,
538 "dma_transfer: ssp rx stall failed\n");
539
540 unmap_dma_buffers(drv_data);
541
542 /* Calculate number of trailing bytes, read them */
543 trailing_sssr = read_SSSR(reg);
544 if ((trailing_sssr & 0xf008) != 0xf000) {
545 drv_data->rx = drv_data->rx_end -
546 (((trailing_sssr >> 12) & 0x0f) + 1);
547 drv_data->read(drv_data);
548 }
549 msg->actual_length += drv_data->len;
550
551 /* Release chip select if requested, transfer delays are
552 * handled in pump_transfers */
553 if (drv_data->cs_change)
554 drv_data->cs_control(PXA2XX_CS_DEASSERT);
555
556 /* Move to next transfer */
557 msg->state = next_transfer(drv_data);
558
559 /* Schedule transfer tasklet */
560 tasklet_schedule(&drv_data->pump_transfers);
561
562 return IRQ_HANDLED;
563 }
564
565 /* Opps problem detected */
566 return IRQ_NONE;
567}
568
569static irqreturn_t interrupt_transfer(struct driver_data *drv_data)
570{
571 u32 irq_status;
572 struct spi_message *msg = drv_data->cur_msg;
573 void *reg = drv_data->ioaddr;
574 irqreturn_t handled = IRQ_NONE;
575 unsigned long limit = loops_per_jiffy << 1;
576
577 while ((irq_status = (read_SSSR(reg) & drv_data->mask_sr))) {
578
579 if (irq_status & SSSR_ROR) {
580
581 /* Clear and disable interrupts */
582 if (drv_data->ssp_type != PXA25x_SSP)
583 write_SSTO(0, reg);
584 write_SSSR(drv_data->clear_sr, reg);
585 write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
586
587 if (flush(drv_data) == 0)
588 dev_err(&drv_data->pdev->dev,
589 "interrupt_transfer: flush fail\n");
590
591 dev_warn(&drv_data->pdev->dev,
592 "interrupt_transfer: fifo overun\n");
593
594 msg->state = ERROR_STATE;
595 tasklet_schedule(&drv_data->pump_transfers);
596
597 return IRQ_HANDLED;
598 }
599
600 /* Look for false positive timeout */
601 if ((irq_status & SSSR_TINT)
602 && (drv_data->rx < drv_data->rx_end))
603 write_SSSR(SSSR_TINT, reg);
604
605 /* Pump data */
606 drv_data->read(drv_data);
607 drv_data->write(drv_data);
608
609 if (drv_data->tx == drv_data->tx_end) {
610 /* Disable tx interrupt */
611 write_SSCR1(read_SSCR1(reg) & ~SSCR1_TIE, reg);
612
613 /* PXA25x_SSP has no timeout, read trailing bytes */
614 if (drv_data->ssp_type == PXA25x_SSP) {
615 while ((read_SSSR(reg) & SSSR_BSY) && limit--)
616 drv_data->read(drv_data);
617
618 if (limit == 0)
619 dev_err(&drv_data->pdev->dev,
620 "interrupt_transfer: "
621 "trailing byte read failed\n");
622 }
623 }
624
625 if ((irq_status & SSSR_TINT)
626 || (drv_data->rx == drv_data->rx_end)) {
627
628 /* Clear timeout */
629 if (drv_data->ssp_type != PXA25x_SSP)
630 write_SSTO(0, reg);
631 write_SSSR(drv_data->clear_sr, reg);
632 write_SSCR1(read_SSCR1(reg) & ~drv_data->int_cr1, reg);
633
634 /* Update total byte transfered */
635 msg->actual_length += drv_data->len;
636
637 /* Release chip select if requested, transfer delays are
638 * handled in pump_transfers */
639 if (drv_data->cs_change)
640 drv_data->cs_control(PXA2XX_CS_DEASSERT);
641
642 /* Move to next transfer */
643 msg->state = next_transfer(drv_data);
644
645 /* Schedule transfer tasklet */
646 tasklet_schedule(&drv_data->pump_transfers);
647
648 return IRQ_HANDLED;
649 }
650
651 /* We did something */
652 handled = IRQ_HANDLED;
653 }
654
655 return handled;
656}
657
658static irqreturn_t ssp_int(int irq, void *dev_id, struct pt_regs *regs)
659{
660 struct driver_data *drv_data = (struct driver_data *)dev_id;
661
662 if (!drv_data->cur_msg) {
663 dev_err(&drv_data->pdev->dev, "bad message state "
664 "in interrupt handler\n");
665 /* Never fail */
666 return IRQ_HANDLED;
667 }
668
669 return drv_data->transfer_handler(drv_data);
670}
671
672static void pump_transfers(unsigned long data)
673{
674 struct driver_data *drv_data = (struct driver_data *)data;
675 struct spi_message *message = NULL;
676 struct spi_transfer *transfer = NULL;
677 struct spi_transfer *previous = NULL;
678 struct chip_data *chip = NULL;
679 void *reg = drv_data->ioaddr;
680
681 /* Get current state information */
682 message = drv_data->cur_msg;
683 transfer = drv_data->cur_transfer;
684 chip = drv_data->cur_chip;
685
686 /* Handle for abort */
687 if (message->state == ERROR_STATE) {
688 message->status = -EIO;
689 giveback(message, drv_data);
690 return;
691 }
692
693 /* Handle end of message */
694 if (message->state == DONE_STATE) {
695 message->status = 0;
696 giveback(message, drv_data);
697 return;
698 }
699
700 /* Delay if requested at end of transfer*/
701 if (message->state == RUNNING_STATE) {
702 previous = list_entry(transfer->transfer_list.prev,
703 struct spi_transfer,
704 transfer_list);
705 if (previous->delay_usecs)
706 udelay(previous->delay_usecs);
707 }
708
709 /* Setup the transfer state based on the type of transfer */
710 if (flush(drv_data) == 0) {
711 dev_err(&drv_data->pdev->dev, "pump_transfers: flush failed\n");
712 message->status = -EIO;
713 giveback(message, drv_data);
714 return;
715 }
716 drv_data->cs_control = chip->cs_control;
717 drv_data->tx = (void *)transfer->tx_buf;
718 drv_data->tx_end = drv_data->tx + transfer->len;
719 drv_data->rx = transfer->rx_buf;
720 drv_data->rx_end = drv_data->rx + transfer->len;
721 drv_data->rx_dma = transfer->rx_dma;
722 drv_data->tx_dma = transfer->tx_dma;
723 drv_data->len = transfer->len;
724 drv_data->write = drv_data->tx ? chip->write : null_writer;
725 drv_data->read = drv_data->rx ? chip->read : null_reader;
726 drv_data->cs_change = transfer->cs_change;
727 message->state = RUNNING_STATE;
728
729 /* Try to map dma buffer and do a dma transfer if successful */
730 if ((drv_data->dma_mapped = map_dma_buffers(drv_data))) {
731
732 /* Ensure we have the correct interrupt handler */
733 drv_data->transfer_handler = dma_transfer;
734
735 /* Setup rx DMA Channel */
736 DCSR(drv_data->rx_channel) = RESET_DMA_CHANNEL;
737 DSADR(drv_data->rx_channel) = drv_data->ssdr_physical;
738 DTADR(drv_data->rx_channel) = drv_data->rx_dma;
739 if (drv_data->rx == drv_data->null_dma_buf)
740 /* No target address increment */
741 DCMD(drv_data->rx_channel) = DCMD_FLOWSRC
742 | chip->dma_width
743 | chip->dma_burst_size
744 | drv_data->len;
745 else
746 DCMD(drv_data->rx_channel) = DCMD_INCTRGADDR
747 | DCMD_FLOWSRC
748 | chip->dma_width
749 | chip->dma_burst_size
750 | drv_data->len;
751
752 /* Setup tx DMA Channel */
753 DCSR(drv_data->tx_channel) = RESET_DMA_CHANNEL;
754 DSADR(drv_data->tx_channel) = drv_data->tx_dma;
755 DTADR(drv_data->tx_channel) = drv_data->ssdr_physical;
756 if (drv_data->tx == drv_data->null_dma_buf)
757 /* No source address increment */
758 DCMD(drv_data->tx_channel) = DCMD_FLOWTRG
759 | chip->dma_width
760 | chip->dma_burst_size
761 | drv_data->len;
762 else
763 DCMD(drv_data->tx_channel) = DCMD_INCSRCADDR
764 | DCMD_FLOWTRG
765 | chip->dma_width
766 | chip->dma_burst_size
767 | drv_data->len;
768
769 /* Enable dma end irqs on SSP to detect end of transfer */
770 if (drv_data->ssp_type == PXA25x_SSP)
771 DCMD(drv_data->tx_channel) |= DCMD_ENDIRQEN;
772
773 /* Fix me, need to handle cs polarity */
774 drv_data->cs_control(PXA2XX_CS_ASSERT);
775
776 /* Go baby, go */
777 write_SSSR(drv_data->clear_sr, reg);
778 DCSR(drv_data->rx_channel) |= DCSR_RUN;
779 DCSR(drv_data->tx_channel) |= DCSR_RUN;
780 if (drv_data->ssp_type != PXA25x_SSP)
781 write_SSTO(chip->timeout, reg);
782 write_SSCR1(chip->cr1
783 | chip->dma_threshold
784 | drv_data->dma_cr1,
785 reg);
786 } else {
787 /* Ensure we have the correct interrupt handler */
788 drv_data->transfer_handler = interrupt_transfer;
789
790 /* Fix me, need to handle cs polarity */
791 drv_data->cs_control(PXA2XX_CS_ASSERT);
792
793 /* Go baby, go */
794 write_SSSR(drv_data->clear_sr, reg);
795 if (drv_data->ssp_type != PXA25x_SSP)
796 write_SSTO(chip->timeout, reg);
797 write_SSCR1(chip->cr1
798 | chip->threshold
799 | drv_data->int_cr1,
800 reg);
801 }
802}
803
804static void pump_messages(void *data)
805{
806 struct driver_data *drv_data = data;
807 unsigned long flags;
808
809 /* Lock queue and check for queue work */
810 spin_lock_irqsave(&drv_data->lock, flags);
811 if (list_empty(&drv_data->queue) || drv_data->run == QUEUE_STOPPED) {
812 drv_data->busy = 0;
813 spin_unlock_irqrestore(&drv_data->lock, flags);
814 return;
815 }
816
817 /* Make sure we are not already running a message */
818 if (drv_data->cur_msg) {
819 spin_unlock_irqrestore(&drv_data->lock, flags);
820 return;
821 }
822
823 /* Extract head of queue */
824 drv_data->cur_msg = list_entry(drv_data->queue.next,
825 struct spi_message, queue);
826 list_del_init(&drv_data->cur_msg->queue);
827 drv_data->busy = 1;
828 spin_unlock_irqrestore(&drv_data->lock, flags);
829
830 /* Initial message state*/
831 drv_data->cur_msg->state = START_STATE;
832 drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next,
833 struct spi_transfer,
834 transfer_list);
835
836 /* Setup the SSP using the per chip configuration */
837 drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi);
838 restore_state(drv_data);
839
840 /* Mark as busy and launch transfers */
841 tasklet_schedule(&drv_data->pump_transfers);
842}
843
844static int transfer(struct spi_device *spi, struct spi_message *msg)
845{
846 struct driver_data *drv_data = spi_master_get_devdata(spi->master);
847 unsigned long flags;
848
849 spin_lock_irqsave(&drv_data->lock, flags);
850
851 if (drv_data->run == QUEUE_STOPPED) {
852 spin_unlock_irqrestore(&drv_data->lock, flags);
853 return -ESHUTDOWN;
854 }
855
856 msg->actual_length = 0;
857 msg->status = -EINPROGRESS;
858 msg->state = START_STATE;
859
860 list_add_tail(&msg->queue, &drv_data->queue);
861
862 if (drv_data->run == QUEUE_RUNNING && !drv_data->busy)
863 queue_work(drv_data->workqueue, &drv_data->pump_messages);
864
865 spin_unlock_irqrestore(&drv_data->lock, flags);
866
867 return 0;
868}
869
870static int setup(struct spi_device *spi)
871{
872 struct pxa2xx_spi_chip *chip_info = NULL;
873 struct chip_data *chip;
874 struct driver_data *drv_data = spi_master_get_devdata(spi->master);
875 unsigned int clk_div;
876
877 if (!spi->bits_per_word)
878 spi->bits_per_word = 8;
879
880 if (drv_data->ssp_type != PXA25x_SSP
881 && (spi->bits_per_word < 4 || spi->bits_per_word > 32))
882 return -EINVAL;
883 else if (spi->bits_per_word < 4 || spi->bits_per_word > 16)
884 return -EINVAL;
885
886 /* Only alloc (or use chip_info) on first setup */
887 chip = spi_get_ctldata(spi);
888 if (chip == NULL) {
889 chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
890 if (!chip)
891 return -ENOMEM;
892
893 chip->cs_control = null_cs_control;
894 chip->enable_dma = 0;
895 chip->timeout = 5;
896 chip->threshold = SSCR1_RxTresh(1) | SSCR1_TxTresh(1);
897 chip->dma_burst_size = drv_data->master_info->enable_dma ?
898 DCMD_BURST8 : 0;
899
900 chip_info = spi->controller_data;
901 }
902
903 /* chip_info isn't always needed */
904 if (chip_info) {
905 if (chip_info->cs_control)
906 chip->cs_control = chip_info->cs_control;
907
908 chip->timeout = (chip_info->timeout_microsecs * 10000) / 2712;
909
910 chip->threshold = SSCR1_RxTresh(chip_info->rx_threshold)
911 | SSCR1_TxTresh(chip_info->tx_threshold);
912
913 chip->enable_dma = chip_info->dma_burst_size != 0
914 && drv_data->master_info->enable_dma;
915 chip->dma_threshold = 0;
916
917 if (chip->enable_dma) {
918 if (chip_info->dma_burst_size <= 8) {
919 chip->dma_threshold = SSCR1_RxTresh(8)
920 | SSCR1_TxTresh(8);
921 chip->dma_burst_size = DCMD_BURST8;
922 } else if (chip_info->dma_burst_size <= 16) {
923 chip->dma_threshold = SSCR1_RxTresh(16)
924 | SSCR1_TxTresh(16);
925 chip->dma_burst_size = DCMD_BURST16;
926 } else {
927 chip->dma_threshold = SSCR1_RxTresh(32)
928 | SSCR1_TxTresh(32);
929 chip->dma_burst_size = DCMD_BURST32;
930 }
931 }
932
933
934 if (chip_info->enable_loopback)
935 chip->cr1 = SSCR1_LBM;
936 }
937
938 if (drv_data->ioaddr == SSP1_VIRT)
939 clk_div = SSP1_SerClkDiv(spi->max_speed_hz);
940 else if (drv_data->ioaddr == SSP2_VIRT)
941 clk_div = SSP2_SerClkDiv(spi->max_speed_hz);
942 else if (drv_data->ioaddr == SSP3_VIRT)
943 clk_div = SSP3_SerClkDiv(spi->max_speed_hz);
944 else
945 return -ENODEV;
946
947 chip->cr0 = clk_div
948 | SSCR0_Motorola
949 | SSCR0_DataSize(spi->bits_per_word & 0x0f)
950 | SSCR0_SSE
951 | (spi->bits_per_word > 16 ? SSCR0_EDSS : 0);
952 chip->cr1 |= (((spi->mode & SPI_CPHA) != 0) << 4)
953 | (((spi->mode & SPI_CPOL) != 0) << 3);
954
955 /* NOTE: PXA25x_SSP _could_ use external clocking ... */
956 if (drv_data->ssp_type != PXA25x_SSP)
957 dev_dbg(&spi->dev, "%d bits/word, %d Hz, mode %d\n",
958 spi->bits_per_word,
959 (CLOCK_SPEED_HZ)
960 / (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
961 spi->mode & 0x3);
962 else
963 dev_dbg(&spi->dev, "%d bits/word, %d Hz, mode %d\n",
964 spi->bits_per_word,
965 (CLOCK_SPEED_HZ/2)
966 / (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
967 spi->mode & 0x3);
968
969 if (spi->bits_per_word <= 8) {
970 chip->n_bytes = 1;
971 chip->dma_width = DCMD_WIDTH1;
972 chip->read = u8_reader;
973 chip->write = u8_writer;
974 } else if (spi->bits_per_word <= 16) {
975 chip->n_bytes = 2;
976 chip->dma_width = DCMD_WIDTH2;
977 chip->read = u16_reader;
978 chip->write = u16_writer;
979 } else if (spi->bits_per_word <= 32) {
980 chip->cr0 |= SSCR0_EDSS;
981 chip->n_bytes = 4;
982 chip->dma_width = DCMD_WIDTH4;
983 chip->read = u32_reader;
984 chip->write = u32_writer;
985 } else {
986 dev_err(&spi->dev, "invalid wordsize\n");
987 kfree(chip);
988 return -ENODEV;
989 }
990
991 spi_set_ctldata(spi, chip);
992
993 return 0;
994}
995
996static void cleanup(const struct spi_device *spi)
997{
998 struct chip_data *chip = spi_get_ctldata((struct spi_device *)spi);
999
1000 kfree(chip);
1001}
1002
1003static int init_queue(struct driver_data *drv_data)
1004{
1005 INIT_LIST_HEAD(&drv_data->queue);
1006 spin_lock_init(&drv_data->lock);
1007
1008 drv_data->run = QUEUE_STOPPED;
1009 drv_data->busy = 0;
1010
1011 tasklet_init(&drv_data->pump_transfers,
1012 pump_transfers, (unsigned long)drv_data);
1013
1014 INIT_WORK(&drv_data->pump_messages, pump_messages, drv_data);
1015 drv_data->workqueue = create_singlethread_workqueue(
1016 drv_data->master->cdev.dev->bus_id);
1017 if (drv_data->workqueue == NULL)
1018 return -EBUSY;
1019
1020 return 0;
1021}
1022
1023static int start_queue(struct driver_data *drv_data)
1024{
1025 unsigned long flags;
1026
1027 spin_lock_irqsave(&drv_data->lock, flags);
1028
1029 if (drv_data->run == QUEUE_RUNNING || drv_data->busy) {
1030 spin_unlock_irqrestore(&drv_data->lock, flags);
1031 return -EBUSY;
1032 }
1033
1034 drv_data->run = QUEUE_RUNNING;
1035 drv_data->cur_msg = NULL;
1036 drv_data->cur_transfer = NULL;
1037 drv_data->cur_chip = NULL;
1038 spin_unlock_irqrestore(&drv_data->lock, flags);
1039
1040 queue_work(drv_data->workqueue, &drv_data->pump_messages);
1041
1042 return 0;
1043}
1044
1045static int stop_queue(struct driver_data *drv_data)
1046{
1047 unsigned long flags;
1048 unsigned limit = 500;
1049 int status = 0;
1050
1051 spin_lock_irqsave(&drv_data->lock, flags);
1052
1053 /* This is a bit lame, but is optimized for the common execution path.
1054 * A wait_queue on the drv_data->busy could be used, but then the common
1055 * execution path (pump_messages) would be required to call wake_up or
1056 * friends on every SPI message. Do this instead */
1057 drv_data->run = QUEUE_STOPPED;
1058 while (!list_empty(&drv_data->queue) && drv_data->busy && limit--) {
1059 spin_unlock_irqrestore(&drv_data->lock, flags);
1060 msleep(10);
1061 spin_lock_irqsave(&drv_data->lock, flags);
1062 }
1063
1064 if (!list_empty(&drv_data->queue) || drv_data->busy)
1065 status = -EBUSY;
1066
1067 spin_unlock_irqrestore(&drv_data->lock, flags);
1068
1069 return status;
1070}
1071
1072static int destroy_queue(struct driver_data *drv_data)
1073{
1074 int status;
1075
1076 status = stop_queue(drv_data);
1077 if (status != 0)
1078 return status;
1079
1080 destroy_workqueue(drv_data->workqueue);
1081
1082 return 0;
1083}
1084
1085static int pxa2xx_spi_probe(struct platform_device *pdev)
1086{
1087 struct device *dev = &pdev->dev;
1088 struct pxa2xx_spi_master *platform_info;
1089 struct spi_master *master;
1090 struct driver_data *drv_data = 0;
1091 struct resource *memory_resource;
1092 int irq;
1093 int status = 0;
1094
1095 platform_info = dev->platform_data;
1096
1097 if (platform_info->ssp_type == SSP_UNDEFINED) {
1098 dev_err(&pdev->dev, "undefined SSP\n");
1099 return -ENODEV;
1100 }
1101
1102 /* Allocate master with space for drv_data and null dma buffer */
1103 master = spi_alloc_master(dev, sizeof(struct driver_data) + 16);
1104 if (!master) {
1105 dev_err(&pdev->dev, "can not alloc spi_master\n");
1106 return -ENOMEM;
1107 }
1108 drv_data = spi_master_get_devdata(master);
1109 drv_data->master = master;
1110 drv_data->master_info = platform_info;
1111 drv_data->pdev = pdev;
1112
1113 master->bus_num = pdev->id;
1114 master->num_chipselect = platform_info->num_chipselect;
1115 master->cleanup = cleanup;
1116 master->setup = setup;
1117 master->transfer = transfer;
1118
1119 drv_data->ssp_type = platform_info->ssp_type;
1120 drv_data->null_dma_buf = (u32 *)ALIGN((u32)(drv_data +
1121 sizeof(struct driver_data)), 8);
1122
1123 /* Setup register addresses */
1124 memory_resource = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1125 if (!memory_resource) {
1126 dev_err(&pdev->dev, "memory resources not defined\n");
1127 status = -ENODEV;
1128 goto out_error_master_alloc;
1129 }
1130
1131 drv_data->ioaddr = (void *)io_p2v(memory_resource->start);
1132 drv_data->ssdr_physical = memory_resource->start + 0x00000010;
1133 if (platform_info->ssp_type == PXA25x_SSP) {
1134 drv_data->int_cr1 = SSCR1_TIE | SSCR1_RIE;
1135 drv_data->dma_cr1 = 0;
1136 drv_data->clear_sr = SSSR_ROR;
1137 drv_data->mask_sr = SSSR_RFS | SSSR_TFS | SSSR_ROR;
1138 } else {
1139 drv_data->int_cr1 = SSCR1_TIE | SSCR1_RIE | SSCR1_TINTE;
1140 drv_data->dma_cr1 = SSCR1_TSRE | SSCR1_RSRE | SSCR1_TINTE;
1141 drv_data->clear_sr = SSSR_ROR | SSSR_TINT;
1142 drv_data->mask_sr = SSSR_TINT | SSSR_RFS | SSSR_TFS | SSSR_ROR;
1143 }
1144
1145 /* Attach to IRQ */
1146 irq = platform_get_irq(pdev, 0);
1147 if (irq < 0) {
1148 dev_err(&pdev->dev, "irq resource not defined\n");
1149 status = -ENODEV;
1150 goto out_error_master_alloc;
1151 }
1152
1153 status = request_irq(irq, ssp_int, SA_INTERRUPT, dev->bus_id, drv_data);
1154 if (status < 0) {
1155 dev_err(&pdev->dev, "can not get IRQ\n");
1156 goto out_error_master_alloc;
1157 }
1158
1159 /* Setup DMA if requested */
1160 drv_data->tx_channel = -1;
1161 drv_data->rx_channel = -1;
1162 if (platform_info->enable_dma) {
1163
1164 /* Get two DMA channels (rx and tx) */
1165 drv_data->rx_channel = pxa_request_dma("pxa2xx_spi_ssp_rx",
1166 DMA_PRIO_HIGH,
1167 dma_handler,
1168 drv_data);
1169 if (drv_data->rx_channel < 0) {
1170 dev_err(dev, "problem (%d) requesting rx channel\n",
1171 drv_data->rx_channel);
1172 status = -ENODEV;
1173 goto out_error_irq_alloc;
1174 }
1175 drv_data->tx_channel = pxa_request_dma("pxa2xx_spi_ssp_tx",
1176 DMA_PRIO_MEDIUM,
1177 dma_handler,
1178 drv_data);
1179 if (drv_data->tx_channel < 0) {
1180 dev_err(dev, "problem (%d) requesting tx channel\n",
1181 drv_data->tx_channel);
1182 status = -ENODEV;
1183 goto out_error_dma_alloc;
1184 }
1185
1186 if (drv_data->ioaddr == SSP1_VIRT) {
1187 DRCMRRXSSDR = DRCMR_MAPVLD
1188 | drv_data->rx_channel;
1189 DRCMRTXSSDR = DRCMR_MAPVLD
1190 | drv_data->tx_channel;
1191 } else if (drv_data->ioaddr == SSP2_VIRT) {
1192 DRCMRRXSS2DR = DRCMR_MAPVLD
1193 | drv_data->rx_channel;
1194 DRCMRTXSS2DR = DRCMR_MAPVLD
1195 | drv_data->tx_channel;
1196 } else if (drv_data->ioaddr == SSP3_VIRT) {
1197 DRCMRRXSS3DR = DRCMR_MAPVLD
1198 | drv_data->rx_channel;
1199 DRCMRTXSS3DR = DRCMR_MAPVLD
1200 | drv_data->tx_channel;
1201 } else {
1202 dev_err(dev, "bad SSP type\n");
1203 goto out_error_dma_alloc;
1204 }
1205 }
1206
1207 /* Enable SOC clock */
1208 pxa_set_cken(platform_info->clock_enable, 1);
1209
1210 /* Load default SSP configuration */
1211 write_SSCR0(0, drv_data->ioaddr);
1212 write_SSCR1(SSCR1_RxTresh(4) | SSCR1_TxTresh(12), drv_data->ioaddr);
1213 write_SSCR0(SSCR0_SerClkDiv(2)
1214 | SSCR0_Motorola
1215 | SSCR0_DataSize(8),
1216 drv_data->ioaddr);
1217 if (drv_data->ssp_type != PXA25x_SSP)
1218 write_SSTO(0, drv_data->ioaddr);
1219 write_SSPSP(0, drv_data->ioaddr);
1220
1221 /* Initial and start queue */
1222 status = init_queue(drv_data);
1223 if (status != 0) {
1224 dev_err(&pdev->dev, "problem initializing queue\n");
1225 goto out_error_clock_enabled;
1226 }
1227 status = start_queue(drv_data);
1228 if (status != 0) {
1229 dev_err(&pdev->dev, "problem starting queue\n");
1230 goto out_error_clock_enabled;
1231 }
1232
1233 /* Register with the SPI framework */
1234 platform_set_drvdata(pdev, drv_data);
1235 status = spi_register_master(master);
1236 if (status != 0) {
1237 dev_err(&pdev->dev, "problem registering spi master\n");
1238 goto out_error_queue_alloc;
1239 }
1240
1241 return status;
1242
1243out_error_queue_alloc:
1244 destroy_queue(drv_data);
1245
1246out_error_clock_enabled:
1247 pxa_set_cken(platform_info->clock_enable, 0);
1248
1249out_error_dma_alloc:
1250 if (drv_data->tx_channel != -1)
1251 pxa_free_dma(drv_data->tx_channel);
1252 if (drv_data->rx_channel != -1)
1253 pxa_free_dma(drv_data->rx_channel);
1254
1255out_error_irq_alloc:
1256 free_irq(irq, drv_data);
1257
1258out_error_master_alloc:
1259 spi_master_put(master);
1260 return status;
1261}
1262
1263static int pxa2xx_spi_remove(struct platform_device *pdev)
1264{
1265 struct driver_data *drv_data = platform_get_drvdata(pdev);
1266 int irq;
1267 int status = 0;
1268
1269 if (!drv_data)
1270 return 0;
1271
1272 /* Remove the queue */
1273 status = destroy_queue(drv_data);
1274 if (status != 0)
1275 return status;
1276
1277 /* Disable the SSP at the peripheral and SOC level */
1278 write_SSCR0(0, drv_data->ioaddr);
1279 pxa_set_cken(drv_data->master_info->clock_enable, 0);
1280
1281 /* Release DMA */
1282 if (drv_data->master_info->enable_dma) {
1283 if (drv_data->ioaddr == SSP1_VIRT) {
1284 DRCMRRXSSDR = 0;
1285 DRCMRTXSSDR = 0;
1286 } else if (drv_data->ioaddr == SSP2_VIRT) {
1287 DRCMRRXSS2DR = 0;
1288 DRCMRTXSS2DR = 0;
1289 } else if (drv_data->ioaddr == SSP3_VIRT) {
1290 DRCMRRXSS3DR = 0;
1291 DRCMRTXSS3DR = 0;
1292 }
1293 pxa_free_dma(drv_data->tx_channel);
1294 pxa_free_dma(drv_data->rx_channel);
1295 }
1296
1297 /* Release IRQ */
1298 irq = platform_get_irq(pdev, 0);
1299 if (irq >= 0)
1300 free_irq(irq, drv_data);
1301
1302 /* Disconnect from the SPI framework */
1303 spi_unregister_master(drv_data->master);
1304
1305 /* Prevent double remove */
1306 platform_set_drvdata(pdev, NULL);
1307
1308 return 0;
1309}
1310
1311static void pxa2xx_spi_shutdown(struct platform_device *pdev)
1312{
1313 int status = 0;
1314
1315 if ((status = pxa2xx_spi_remove(pdev)) != 0)
1316 dev_err(&pdev->dev, "shutdown failed with %d\n", status);
1317}
1318
1319#ifdef CONFIG_PM
1320static int suspend_devices(struct device *dev, void *pm_message)
1321{
1322 pm_message_t *state = pm_message;
1323
1324 if (dev->power.power_state.event != state->event) {
1325 dev_warn(dev, "pm state does not match request\n");
1326 return -1;
1327 }
1328
1329 return 0;
1330}
1331
1332static int pxa2xx_spi_suspend(struct platform_device *pdev, pm_message_t state)
1333{
1334 struct driver_data *drv_data = platform_get_drvdata(pdev);
1335 int status = 0;
1336
1337 /* Check all childern for current power state */
1338 if (device_for_each_child(&pdev->dev, &state, suspend_devices) != 0) {
1339 dev_warn(&pdev->dev, "suspend aborted\n");
1340 return -1;
1341 }
1342
1343 status = stop_queue(drv_data);
1344 if (status != 0)
1345 return status;
1346 write_SSCR0(0, drv_data->ioaddr);
1347 pxa_set_cken(drv_data->master_info->clock_enable, 0);
1348
1349 return 0;
1350}
1351
1352static int pxa2xx_spi_resume(struct platform_device *pdev)
1353{
1354 struct driver_data *drv_data = platform_get_drvdata(pdev);
1355 int status = 0;
1356
1357 /* Enable the SSP clock */
1358 pxa_set_cken(drv_data->master_info->clock_enable, 1);
1359
1360 /* Start the queue running */
1361 status = start_queue(drv_data);
1362 if (status != 0) {
1363 dev_err(&pdev->dev, "problem starting queue (%d)\n", status);
1364 return status;
1365 }
1366
1367 return 0;
1368}
1369#else
1370#define pxa2xx_spi_suspend NULL
1371#define pxa2xx_spi_resume NULL
1372#endif /* CONFIG_PM */
1373
1374static struct platform_driver driver = {
1375 .driver = {
1376 .name = "pxa2xx-spi",
1377 .bus = &platform_bus_type,
1378 .owner = THIS_MODULE,
1379 },
1380 .probe = pxa2xx_spi_probe,
1381 .remove = __devexit_p(pxa2xx_spi_remove),
1382 .shutdown = pxa2xx_spi_shutdown,
1383 .suspend = pxa2xx_spi_suspend,
1384 .resume = pxa2xx_spi_resume,
1385};
1386
1387static int __init pxa2xx_spi_init(void)
1388{
1389 platform_driver_register(&driver);
1390
1391 return 0;
1392}
1393module_init(pxa2xx_spi_init);
1394
1395static void __exit pxa2xx_spi_exit(void)
1396{
1397 platform_driver_unregister(&driver);
1398}
1399module_exit(pxa2xx_spi_exit);
diff --git a/include/asm-arm/arch-pxa/pxa2xx_spi.h b/include/asm-arm/arch-pxa/pxa2xx_spi.h
new file mode 100644
index 000000000000..1e70908b816f
--- /dev/null
+++ b/include/asm-arm/arch-pxa/pxa2xx_spi.h
@@ -0,0 +1,68 @@
1/*
2 * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
3 *
4 * This program is free software; you can redistribute it and/or modify
5 * it under the terms of the GNU General Public License as published by
6 * the Free Software Foundation; either version 2 of the License, or
7 * (at your option) any later version.
8 *
9 * This program is distributed in the hope that it will be useful,
10 * but WITHOUT ANY WARRANTY; without even the implied warranty of
11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
12 * GNU General Public License for more details.
13 *
14 * You should have received a copy of the GNU General Public License
15 * along with this program; if not, write to the Free Software
16 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
17 */
18
19#ifndef PXA2XX_SPI_H_
20#define PXA2XX_SPI_H_
21
22#define PXA2XX_CS_ASSERT (0x01)
23#define PXA2XX_CS_DEASSERT (0x02)
24
25#if defined(CONFIG_PXA25x)
26#define CLOCK_SPEED_HZ 3686400
27#define SSP1_SerClkDiv(x) (((CLOCK_SPEED_HZ/2/(x+1))<<8)&0x0000ff00)
28#define SSP2_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
29#define SSP3_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
30#elif defined(CONFIG_PXA27x)
31#define CLOCK_SPEED_HZ 13000000
32#define SSP1_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
33#define SSP2_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
34#define SSP3_SerClkDiv(x) (((CLOCK_SPEED_HZ/(x+1))<<8)&0x000fff00)
35#endif
36
37#define SSP1_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(1)))))
38#define SSP2_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(2)))))
39#define SSP3_VIRT ((void *)(io_p2v(__PREG(SSCR0_P(3)))))
40
41enum pxa_ssp_type {
42 SSP_UNDEFINED = 0,
43 PXA25x_SSP, /* pxa 210, 250, 255, 26x */
44 PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
45 PXA27x_SSP,
46};
47
48/* device.platform_data for SSP controller devices */
49struct pxa2xx_spi_master {
50 enum pxa_ssp_type ssp_type;
51 u32 clock_enable;
52 u16 num_chipselect;
53 u8 enable_dma;
54};
55
56/* spi_board_info.controller_data for SPI slave devices,
57 * copied to spi_device.platform_data ... mostly for dma tuning
58 */
59struct pxa2xx_spi_chip {
60 u8 tx_threshold;
61 u8 rx_threshold;
62 u8 dma_burst_size;
63 u32 timeout_microsecs;
64 u8 enable_loopback;
65 void (*cs_control)(u32 command);
66};
67
68#endif /*PXA2XX_SPI_H_*/
generated by cgit v1.2.2 (git 2.25.0) at 2025-11-15 06:47:17 -0500