aboutsummaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
Diffstat
-rw-r--r--drivers/serial/Kconfig10
-rw-r--r--drivers/serial/Makefile1
-rw-r--r--drivers/serial/mfd.c1488
-rw-r--r--include/linux/serial_core.h2
-rw-r--r--include/linux/serial_mfd.h47
-rw-r--r--include/linux/serial_reg.h16
6 files changed, 1564 insertions, 0 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index c34c217878b3..a22e60c06f48 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -724,6 +724,16 @@ config MRST_MAX3110_IRQ
724 help 724 help
725 This has to be enabled after Moorestown GPIO driver is loaded 725 This has to be enabled after Moorestown GPIO driver is loaded
726 726
727config SERIAL_MFD_HSU
728 tristate "Medfield High Speed UART support"
729 depends on PCI
730 select SERIAL_CORE
731
732config SERIAL_MFD_HSU_CONSOLE
733 boolean "Medfile HSU serial console support"
734 depends on SERIAL_MFD_HSU=y
735 select SERIAL_CORE_CONSOLE
736
727config SERIAL_BFIN 737config SERIAL_BFIN
728 tristate "Blackfin serial port support" 738 tristate "Blackfin serial port support"
729 depends on BLACKFIN 739 depends on BLACKFIN
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 424067ac3347..1ca4fd599ffe 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -87,3 +87,4 @@ obj-$(CONFIG_SERIAL_GRLIB_GAISLER_APBUART) += apbuart.o
87obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o 87obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o
88obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o 88obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
89obj-$(CONFIG_SERIAL_MRST_MAX3110) += mrst_max3110.o 89obj-$(CONFIG_SERIAL_MRST_MAX3110) += mrst_max3110.o
90obj-$(CONFIG_SERIAL_MFD_HSU) += mfd.o
diff --git a/drivers/serial/mfd.c b/drivers/serial/mfd.c
new file mode 100644
index 000000000000..300dcb134e07
--- /dev/null
+++ b/drivers/serial/mfd.c
@@ -0,0 +1,1488 @@
1/*
2 * mfd.c: driver for High Speed UART device of Intel Medfield platform
3 *
4 * Refer pxa.c, 8250.c and some other drivers in drivers/serial/
5 *
6 * (C) Copyright 2009 Intel Corporation
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License
10 * as published by the Free Software Foundation; version 2
11 * of the License.
12 */
13
14
15/* Notes:
16 * 1. there should be 2 types of register access method, one for
17 * UART ports, the other for the general purpose registers
18 *
19 * 2. It used to have a Irda port, but was defeatured recently
20 *
21 * 3. Based on the info from HSU MAS, 0/1 channel are assigned to
22 * port0, 2/3 chan to port 1, 4/5 chan to port 3. Even number
23 * chan will be read, odd chan for write
24 *
25 * 4. HUS supports both the 64B and 16B FIFO version, but this driver
26 * will only use 64B version
27 *
28 * 5. In A0 stepping, UART will not support TX half empty flag, thus
29 * need add a #ifdef judgement
30 *
31 * 6. One more bug for A0, the loopback mode won't support AFC
32 * auto-flow control
33 *
34 * 7. HSU has some special FCR control bits, we add it to serial_reg.h
35 *
36 * 8. The RI/DSR/DCD/DTR are not pinned out, DCD & DSR are always asserted,
37 * only when the HW is reset the DDCD and DDSR will be triggered
38 */
39
40#include <linux/module.h>
41#include <linux/init.h>
42#include <linux/console.h>
43#include <linux/sysrq.h>
44#include <linux/serial_reg.h>
45#include <linux/circ_buf.h>
46#include <linux/delay.h>
47#include <linux/interrupt.h>
48#include <linux/tty.h>
49#include <linux/tty_flip.h>
50#include <linux/serial_core.h>
51#include <linux/serial_mfd.h>
52#include <linux/dma-mapping.h>
53#include <linux/pci.h>
54#include <linux/io.h>
55#include <linux/debugfs.h>
56
57#define MFD_HSU_A0_STEPPING 1
58
59#define HSU_DMA_BUF_SIZE 2048
60
61#define chan_readl(chan, offset) readl(chan->reg + offset)
62#define chan_writel(chan, offset, val) writel(val, chan->reg + offset)
63
64#define mfd_readl(obj, offset) readl(obj->reg + offset)
65#define mfd_writel(obj, offset, val) writel(val, obj->reg + offset)
66
67struct hsu_dma_buffer {
68 u8 *buf;
69 dma_addr_t dma_addr;
70 u32 dma_size;
71 u32 ofs;
72};
73
74struct hsu_dma_chan {
75 u32 id;
76 u32 dirt; /* to or from device */
77 struct uart_hsu_port *uport;
78 void __iomem *reg;
79};
80
81struct uart_hsu_port {
82 struct uart_port port;
83 unsigned char ier;
84 unsigned char lcr;
85 unsigned char mcr;
86 unsigned int lsr_break_flag;
87 char name[12];
88 int index;
89 struct device *dev;
90
91 struct hsu_dma_chan *txc;
92 struct hsu_dma_chan *rxc;
93 struct hsu_dma_buffer txbuf;
94 struct hsu_dma_buffer rxbuf;
95 int use_dma; /* flag for DMA/PIO */
96 int running;
97 int dma_tx_on;
98};
99
100/* Top level data structure of HSU */
101struct hsu_port {
102 struct pci_device *pdev;
103
104 void __iomem *reg;
105 unsigned long paddr;
106 unsigned long iolen;
107 u32 irq;
108
109 struct uart_hsu_port port[3];
110 struct hsu_dma_chan chans[10];
111
112#ifdef CONFIG_DEBUG_FS
113 struct dentry *debugfs;
114#endif
115};
116
117static inline void hexdump(char *str, u8 *addr, int cnt)
118{
119 int i;
120
121 for (i = 0; i < cnt; i += 8) {
122 printk("0x%02x 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x 0x%02x",
123 addr[i], addr[i+1], addr[i+2], addr[i+3],
124 addr[i+4], addr[i+5], addr[i+6], addr[i+7]);
125 printk("\n");
126 }
127}
128
129static inline unsigned int serial_in(struct uart_hsu_port *up, int offset)
130{
131 unsigned int val;
132
133 if (offset > UART_MSR) {
134 offset <<= 2;
135 val = readl(up->port.membase + offset);
136 } else
137 val = (unsigned int)readb(up->port.membase + offset);
138
139 return val;
140}
141
142static inline void serial_out(struct uart_hsu_port *up, int offset, int value)
143{
144 if (offset > UART_MSR) {
145 offset <<= 2;
146 writel(value, up->port.membase + offset);
147 } else {
148 unsigned char val = value & 0xff;
149 writeb(val, up->port.membase + offset);
150 }
151}
152
153#ifdef CONFIG_DEBUG_FS
154
155#define HSU_REGS_BUFSIZE 1024
156
157static int hsu_show_regs_open(struct inode *inode, struct file *file)
158{
159 file->private_data = inode->i_private;
160 return 0;
161}
162
163static ssize_t port_show_regs(struct file *file, char __user *user_buf,
164 size_t count, loff_t *ppos)
165{
166 struct uart_hsu_port *up = file->private_data;
167 char *buf;
168 u32 len = 0;
169 ssize_t ret;
170
171 buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL);
172 if (!buf)
173 return 0;
174
175 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
176 "MFD HSU port[%d] regs:\n", up->index);
177
178 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
179 "=================================\n");
180 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
181 "IER: \t\t0x%08x\n", serial_in(up, UART_IER));
182 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
183 "IIR: \t\t0x%08x\n", serial_in(up, UART_IIR));
184 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
185 "LCR: \t\t0x%08x\n", serial_in(up, UART_LCR));
186 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
187 "MCR: \t\t0x%08x\n", serial_in(up, UART_MCR));
188 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
189 "LSR: \t\t0x%08x\n", serial_in(up, UART_LSR));
190 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
191 "MSR: \t\t0x%08x\n", serial_in(up, UART_MSR));
192 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
193 "FOR: \t\t0x%08x\n", serial_in(up, UART_FOR));
194 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
195 "PS: \t\t0x%08x\n", serial_in(up, UART_PS));
196 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
197 "MUL: \t\t0x%08x\n", serial_in(up, UART_MUL));
198 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
199 "DIV: \t\t0x%08x\n", serial_in(up, UART_DIV));
200
201 ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
202 kfree(buf);
203 return ret;
204}
205
206static ssize_t dma_show_regs(struct file *file, char __user *user_buf,
207 size_t count, loff_t *ppos)
208{
209 struct hsu_dma_chan *chan = file->private_data;
210 char *buf;
211 u32 len = 0;
212 ssize_t ret;
213
214 buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL);
215 if (!buf)
216 return 0;
217
218 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
219 "MFD HSU DMA channel [%d] regs:\n", chan->id);
220
221 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
222 "=================================\n");
223 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
224 "CR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_CR));
225 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
226 "DCR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_DCR));
227 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
228 "BSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_BSR));
229 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
230 "MOTSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_MOTSR));
231 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
232 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0SAR));
233 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
234 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0TSR));
235 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
236 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1SAR));
237 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
238 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1TSR));
239 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
240 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2SAR));
241 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
242 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2TSR));
243 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
244 "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3SAR));
245 len += snprintf(buf + len, HSU_REGS_BUFSIZE - len,
246 "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3TSR));
247
248 ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
249 kfree(buf);
250 return ret;
251}
252
253static const struct file_operations port_regs_ops = {
254 .owner = THIS_MODULE,
255 .open = hsu_show_regs_open,
256 .read = port_show_regs,
257};
258
259static const struct file_operations dma_regs_ops = {
260 .owner = THIS_MODULE,
261 .open = hsu_show_regs_open,
262 .read = dma_show_regs,
263};
264
265static int hsu_debugfs_init(struct hsu_port *hsu)
266{
267 int i;
268 char name[32];
269
270 hsu->debugfs = debugfs_create_dir("hsu", NULL);
271 if (!hsu->debugfs)
272 return -ENOMEM;
273
274 for (i = 0; i < 3; i++) {
275 snprintf(name, sizeof(name), "port_%d_regs", i);
276 debugfs_create_file(name, S_IFREG | S_IRUGO,
277 hsu->debugfs, (void *)(&hsu->port[i]), &port_regs_ops);
278 }
279
280 for (i = 0; i < 6; i++) {
281 snprintf(name, sizeof(name), "dma_chan_%d_regs", i);
282 debugfs_create_file(name, S_IFREG | S_IRUGO,
283 hsu->debugfs, (void *)&hsu->chans[i], &dma_regs_ops);
284 }
285
286 return 0;
287}
288
289static void hsu_debugfs_remove(struct hsu_port *hsu)
290{
291 if (hsu->debugfs)
292 debugfs_remove_recursive(hsu->debugfs);
293}
294
295#else
296static inline int hsu_debugfs_init(struct hsu_port *hsu)
297{
298 return 0;
299}
300
301static inline void hsu_debugfs_remove(struct hsu_port *hsu)
302{
303}
304#endif /* CONFIG_DEBUG_FS */
305
306static void serial_hsu_enable_ms(struct uart_port *port)
307{
308 struct uart_hsu_port *up =
309 container_of(port, struct uart_hsu_port, port);
310
311 up->ier |= UART_IER_MSI;
312 serial_out(up, UART_IER, up->ier);
313}
314
315void hsu_dma_tx(struct uart_hsu_port *up)
316{
317 struct circ_buf *xmit = &up->port.state->xmit;
318 struct hsu_dma_buffer *dbuf = &up->txbuf;
319 int count;
320
321 /* test_and_set_bit may be better, but anyway it's in lock protected mode */
322 if (up->dma_tx_on)
323 return;
324
325 /* Update the circ buf info */
326 xmit->tail += dbuf->ofs;
327 xmit->tail &= UART_XMIT_SIZE - 1;
328
329 up->port.icount.tx += dbuf->ofs;
330 dbuf->ofs = 0;
331
332 /* Disable the channel */
333 chan_writel(up->txc, HSU_CH_CR, 0x0);
334
335 if (!uart_circ_empty(xmit) && !uart_tx_stopped(&up->port)) {
336 dma_sync_single_for_device(up->port.dev,
337 dbuf->dma_addr,
338 dbuf->dma_size,
339 DMA_TO_DEVICE);
340
341 count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
342 dbuf->ofs = count;
343
344 /* Reprogram the channel */
345 chan_writel(up->txc, HSU_CH_D0SAR, dbuf->dma_addr + xmit->tail);
346 chan_writel(up->txc, HSU_CH_D0TSR, count);
347
348 /* Reenable the channel */
349 chan_writel(up->txc, HSU_CH_DCR, 0x1
350 | (0x1 << 8)
351 | (0x1 << 16)
352 | (0x1 << 24));
353
354 WARN(chan_readl(up->txc, HSU_CH_CR) & 0x1,
355 "TX channel has already be started!!\n");
356 up->dma_tx_on = 1;
357 chan_writel(up->txc, HSU_CH_CR, 0x1);
358 }
359
360 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
361 uart_write_wakeup(&up->port);
362}
363
364/* The buffer is already cache coherent */
365void hsu_dma_start_rx_chan(struct hsu_dma_chan *rxc, struct hsu_dma_buffer *dbuf)
366{
367 /* Need start RX dma channel here */
368 dbuf->ofs = 0;
369
370 chan_writel(rxc, HSU_CH_BSR, 32);
371 chan_writel(rxc, HSU_CH_MOTSR, 4);
372
373 chan_writel(rxc, HSU_CH_D0SAR, dbuf->dma_addr);
374 chan_writel(rxc, HSU_CH_D0TSR, dbuf->dma_size);
375 chan_writel(rxc, HSU_CH_DCR, 0x1 | (0x1 << 8)
376 | (0x1 << 16)
377 | (0x1 << 24) /* timeout bit, see HSU Errata 1 */
378 );
379 chan_writel(rxc, HSU_CH_CR, 0x3);
380}
381
382/* Protected by spin_lock_irqsave(port->lock) */
383static void serial_hsu_start_tx(struct uart_port *port)
384{
385 struct uart_hsu_port *up =
386 container_of(port, struct uart_hsu_port, port);
387
388 if (up->use_dma) {
389 hsu_dma_tx(up);
390 } else if (!(up->ier & UART_IER_THRI)) {
391 up->ier |= UART_IER_THRI;
392 serial_out(up, UART_IER, up->ier);
393 }
394}
395
396static void serial_hsu_stop_tx(struct uart_port *port)
397{
398 struct uart_hsu_port *up =
399 container_of(port, struct uart_hsu_port, port);
400 struct hsu_dma_chan *txc = up->txc;
401
402 if (up->use_dma)
403 chan_writel(txc, HSU_CH_CR, 0x0);
404 else if (up->ier & UART_IER_THRI) {
405 up->ier &= ~UART_IER_THRI;
406 serial_out(up, UART_IER, up->ier);
407 }
408}
409
410/* This is always called in spinlock protected mode, so
411 * modify timeout timer is safe here */
412void hsu_dma_rx(struct uart_hsu_port *up, u32 int_sts)
413{
414 struct hsu_dma_buffer *dbuf = &up->rxbuf;
415 struct hsu_dma_chan *chan = up->rxc;
416 struct uart_port *port = &up->port;
417 struct tty_struct *tty = port->state->port.tty;
418 int count;
419
420 if (!tty)
421 return;
422
423 /*
424 * first need to know how many is already transferred,
425 * then check if its a timeout DMA irq, and return
426 * the trail bytes out, push them up and reenable the
427 * channel, better to use 2 descriptors at the same time
428 */
429
430 /* timeout IRQ, need wait some time, see Errata 2 */
431 if (int_sts & 0xf00)
432 udelay(2);
433
434 /* Stop the channel */
435 chan_writel(chan, HSU_CH_CR, 0x0);
436
437 /* We can use 2 ways to calc the actual transfer len */
438 count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr;
439
440 if (!count)
441 return;
442
443 dma_sync_single_for_cpu(port->dev, dbuf->dma_addr,
444 dbuf->dma_size, DMA_FROM_DEVICE);
445
446 /*
447 * head will only wrap around when we recycle
448 * the DMA buffer, and when that happens, we
449 * explicitly set tail to 0. So head will
450 * always be greater than tail.
451 */
452 tty_insert_flip_string(tty, dbuf->buf, count);
453 port->icount.rx += count;
454
455 dma_sync_single_for_device(up->port.dev, dbuf->dma_addr,
456 dbuf->dma_size, DMA_FROM_DEVICE);
457
458 /* Reprogram the channel */
459 chan_writel(chan, HSU_CH_D0SAR, dbuf->dma_addr);
460 chan_writel(chan, HSU_CH_D0TSR, dbuf->dma_size);
461 chan_writel(chan, HSU_CH_DCR, 0x1
462 | (0x1 << 8)
463 | (0x1 << 16)
464 | (0x1 << 24) /* timeout bit, see HSU Errata 1 */
465 );
466 chan_writel(chan, HSU_CH_CR, 0x3);
467
468 tty_flip_buffer_push(tty);
469}
470
471static void serial_hsu_stop_rx(struct uart_port *port)
472{
473 struct uart_hsu_port *up =
474 container_of(port, struct uart_hsu_port, port);
475 struct hsu_dma_chan *chan = up->rxc;
476
477 if (up->use_dma)
478 chan_writel(chan, HSU_CH_CR, 0x2);
479 else {
480 up->ier &= ~UART_IER_RLSI;
481 up->port.read_status_mask &= ~UART_LSR_DR;
482 serial_out(up, UART_IER, up->ier);
483 }
484}
485
486/*
487 * if there is error flag, should we just reset the FIFO or keeps
488 * working on it
489 */
490static inline void receive_chars(struct uart_hsu_port *up, int *status)
491{
492 struct tty_struct *tty = up->port.state->port.tty;
493 unsigned int ch, flag;
494 unsigned int max_count = 256;
495
496 if (!tty)
497 return;
498
499 do {
500 ch = serial_in(up, UART_RX);
501 flag = TTY_NORMAL;
502 up->port.icount.rx++;
503
504 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
505 UART_LSR_FE | UART_LSR_OE))) {
506
507 dev_warn(up->dev, "We really rush into ERR/BI case"
508 "status = 0x%02x", *status);
509 /* For statistics only */
510 if (*status & UART_LSR_BI) {
511 *status &= ~(UART_LSR_FE | UART_LSR_PE);
512 up->port.icount.brk++;
513 /*
514 * We do the SysRQ and SAK checking
515 * here because otherwise the break
516 * may get masked by ignore_status_mask
517 * or read_status_mask.
518 */
519 if (uart_handle_break(&up->port))
520 goto ignore_char;
521 } else if (*status & UART_LSR_PE)
522 up->port.icount.parity++;
523 else if (*status & UART_LSR_FE)
524 up->port.icount.frame++;
525 if (*status & UART_LSR_OE)
526 up->port.icount.overrun++;
527
528 /* Mask off conditions which should be ignored. */
529 *status &= up->port.read_status_mask;
530
531#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
532 if (up->port.cons &&
533 up->port.cons->index == up->port.line) {
534 /* Recover the break flag from console xmit */
535 *status |= up->lsr_break_flag;
536 up->lsr_break_flag = 0;
537 }
538#endif
539 if (*status & UART_LSR_BI) {
540 flag = TTY_BREAK;
541 } else if (*status & UART_LSR_PE)
542 flag = TTY_PARITY;
543 else if (*status & UART_LSR_FE)
544 flag = TTY_FRAME;
545 }
546
547 if (uart_handle_sysrq_char(&up->port, ch))
548 goto ignore_char;
549
550 uart_insert_char(&up->port, *status, UART_LSR_OE, ch, flag);
551 ignore_char:
552 *status = serial_in(up, UART_LSR);
553 } while ((*status & UART_LSR_DR) && max_count--);
554 tty_flip_buffer_push(tty);
555}
556
557static void transmit_chars(struct uart_hsu_port *up)
558{
559 struct circ_buf *xmit = &up->port.state->xmit;
560 int count;
561 int i = 0; /* for debug use */
562
563 if (up->port.x_char) {
564 serial_out(up, UART_TX, up->port.x_char);
565 up->port.icount.tx++;
566 up->port.x_char = 0;
567 return;
568 }
569 if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
570 serial_hsu_stop_tx(&up->port);
571 return;
572 }
573
574#ifndef MFD_HSU_A0_STEPPING
575 count = up->port.fifosize / 2;
576#else
577 /*
578 * A0 only supports fully empty IRQ, and the first char written
579 * into it won't clear the EMPT bit, so we may need be cautious
580 * by useing a shorter buffer
581 */
582 /* count = up->port.fifosize; */
583 count = up->port.fifosize - 4;
584#endif
585 do {
586 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
587 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
588 i++;
589
590 up->port.icount.tx++;
591 if (uart_circ_empty(xmit))
592 break;
593 } while (--count > 0);
594
595 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
596 uart_write_wakeup(&up->port);
597
598 if (uart_circ_empty(xmit))
599 serial_hsu_stop_tx(&up->port);
600}
601
602static inline void check_modem_status(struct uart_hsu_port *up)
603{
604 int status;
605
606 status = serial_in(up, UART_MSR);
607
608 if ((status & UART_MSR_ANY_DELTA) == 0)
609 return;
610
611 if (status & UART_MSR_TERI)
612 up->port.icount.rng++;
613 if (status & UART_MSR_DDSR)
614 up->port.icount.dsr++;
615 /* We may only get DDCD when HW init and reset */
616 if (status & UART_MSR_DDCD)
617 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
618 /* will start/stop_tx accordingly */
619 if (status & UART_MSR_DCTS)
620 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
621
622 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
623}
624
625/*
626 * This handles the interrupt from one port.
627 */
628static irqreturn_t port_irq(int irq, void *dev_id)
629{
630 struct uart_hsu_port *up = dev_id;
631 unsigned int iir, lsr;
632 unsigned long flags;
633
634 if (unlikely(!up->running))
635 return IRQ_NONE;
636
637 if (up->use_dma) {
638 lsr = serial_in(up, UART_LSR);
639 if (unlikely(lsr & (UART_LSR_BI | UART_LSR_PE |
640 UART_LSR_FE | UART_LSR_OE)))
641 dev_warn(up->dev,
642 "Got lsr irq while using DMA, lsr = 0x%2x\n",
643 lsr);
644 check_modem_status(up);
645 return IRQ_HANDLED;
646 }
647
648 spin_lock_irqsave(&up->port.lock, flags);
649 iir = serial_in(up, UART_IIR);
650 if (iir & UART_IIR_NO_INT) {
651 spin_unlock_irqrestore(&up->port.lock, flags);
652 return IRQ_NONE;
653 }
654
655 lsr = serial_in(up, UART_LSR);
656
657 if (lsr & UART_LSR_DR)
658 receive_chars(up, &lsr);
659
660 /* lsr will be renewed during the receive_chars */
661 if (lsr & UART_LSR_THRE)
662 transmit_chars(up);
663
664 spin_unlock_irqrestore(&up->port.lock, flags);
665 return IRQ_HANDLED;
666}
667
668static inline void dma_chan_irq(struct hsu_dma_chan *chan)
669{
670 struct uart_hsu_port *up = chan->uport;
671 unsigned long flags;
672 u32 int_sts;
673
674 spin_lock_irqsave(&up->port.lock, flags);
675
676 if (!up->use_dma || !up->running)
677 goto exit;
678
679 /*
680 * No matter what situation, need read clear the IRQ status
681 * There is a bug, see Errata 5, HSD 2900918
682 */
683 int_sts = chan_readl(chan, HSU_CH_SR);
684
685 /* Rx channel */
686 if (chan->dirt == DMA_FROM_DEVICE)
687 hsu_dma_rx(up, int_sts);
688
689 /* Tx channel */
690 if (chan->dirt == DMA_TO_DEVICE) {
691 /* dma for irq should be done */
692 chan_writel(chan, HSU_CH_CR, 0x0);
693 up->dma_tx_on = 0;
694 hsu_dma_tx(up);
695 }
696
697exit:
698 spin_unlock_irqrestore(&up->port.lock, flags);
699 return;
700}
701
702static irqreturn_t dma_irq(int irq, void *dev_id)
703{
704 struct hsu_port *hsu = dev_id;
705 u32 int_sts, i;
706
707 int_sts = mfd_readl(hsu, HSU_GBL_DMAISR);
708
709 /* Currently we only have 6 channels may be used */
710 for (i = 0; i < 6; i++) {
711 if (int_sts & 0x1)
712 dma_chan_irq(&hsu->chans[i]);
713 int_sts >>= 1;
714 }
715
716 return IRQ_HANDLED;
717}
718
719static unsigned int serial_hsu_tx_empty(struct uart_port *port)
720{
721 struct uart_hsu_port *up =
722 container_of(port, struct uart_hsu_port, port);
723 unsigned long flags;
724 unsigned int ret;
725
726 spin_lock_irqsave(&up->port.lock, flags);
727 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
728 spin_unlock_irqrestore(&up->port.lock, flags);
729
730 return ret;
731}
732
733static unsigned int serial_hsu_get_mctrl(struct uart_port *port)
734{
735 struct uart_hsu_port *up =
736 container_of(port, struct uart_hsu_port, port);
737 unsigned char status;
738 unsigned int ret;
739
740 status = serial_in(up, UART_MSR);
741
742 ret = 0;
743 if (status & UART_MSR_DCD)
744 ret |= TIOCM_CAR;
745 if (status & UART_MSR_RI)
746 ret |= TIOCM_RNG;
747 if (status & UART_MSR_DSR)
748 ret |= TIOCM_DSR;
749 if (status & UART_MSR_CTS)
750 ret |= TIOCM_CTS;
751 return ret;
752}
753
754static void serial_hsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
755{
756 struct uart_hsu_port *up =
757 container_of(port, struct uart_hsu_port, port);
758 unsigned char mcr = 0;
759
760 if (mctrl & TIOCM_RTS)
761 mcr |= UART_MCR_RTS;
762 if (mctrl & TIOCM_DTR)
763 mcr |= UART_MCR_DTR;
764 if (mctrl & TIOCM_OUT1)
765 mcr |= UART_MCR_OUT1;
766 if (mctrl & TIOCM_OUT2)
767 mcr |= UART_MCR_OUT2;
768 if (mctrl & TIOCM_LOOP)
769 mcr |= UART_MCR_LOOP;
770
771 mcr |= up->mcr;
772
773 serial_out(up, UART_MCR, mcr);
774}
775
776static void serial_hsu_break_ctl(struct uart_port *port, int break_state)
777{
778 struct uart_hsu_port *up =
779 container_of(port, struct uart_hsu_port, port);
780 unsigned long flags;
781
782 spin_lock_irqsave(&up->port.lock, flags);
783 if (break_state == -1)
784 up->lcr |= UART_LCR_SBC;
785 else
786 up->lcr &= ~UART_LCR_SBC;
787 serial_out(up, UART_LCR, up->lcr);
788 spin_unlock_irqrestore(&up->port.lock, flags);
789}
790
791/*
792 * What special to do:
793 * 1. chose the 64B fifo mode
794 * 2. make sure not to select half empty mode for A0 stepping
795 * 3. start dma or pio depends on configuration
796 * 4. we only allocate dma memory when needed
797 */
798static int serial_hsu_startup(struct uart_port *port)
799{
800 struct uart_hsu_port *up =
801 container_of(port, struct uart_hsu_port, port);
802 unsigned long flags;
803
804 /*
805 * Clear the FIFO buffers and disable them.
806 * (they will be reenabled in set_termios())
807 */
808 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
809 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
810 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
811 serial_out(up, UART_FCR, 0);
812
813 /* Clear the interrupt registers. */
814 (void) serial_in(up, UART_LSR);
815 (void) serial_in(up, UART_RX);
816 (void) serial_in(up, UART_IIR);
817 (void) serial_in(up, UART_MSR);
818
819 /* Now, initialize the UART, default is 8n1 */
820 serial_out(up, UART_LCR, UART_LCR_WLEN8);
821
822 spin_lock_irqsave(&up->port.lock, flags);
823
824 up->port.mctrl |= TIOCM_OUT2;
825 serial_hsu_set_mctrl(&up->port, up->port.mctrl);
826
827 /*
828 * Finally, enable interrupts. Note: Modem status interrupts
829 * are set via set_termios(), which will be occurring imminently
830 * anyway, so we don't enable them here.
831 */
832 if (!up->use_dma)
833 up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE;
834 else
835 up->ier = 0;
836 serial_out(up, UART_IER, up->ier);
837
838 spin_unlock_irqrestore(&up->port.lock, flags);
839
840 /* DMA init */
841 /* When use DMA, TX/RX's FIFO and IRQ should be disabled */
842 if (up->use_dma) {
843 struct hsu_dma_buffer *dbuf;
844 struct circ_buf *xmit = &port->state->xmit;
845
846 up->dma_tx_on = 0;
847
848 /* First allocate the RX buffer */
849 dbuf = &up->rxbuf;
850 dbuf->buf = kzalloc(HSU_DMA_BUF_SIZE, GFP_KERNEL);
851 if (!dbuf->buf) {
852 up->use_dma = 0;
853 goto exit;
854 }
855 dbuf->dma_addr = dma_map_single(port->dev,
856 dbuf->buf,
857 HSU_DMA_BUF_SIZE,
858 DMA_FROM_DEVICE);
859 dbuf->dma_size = HSU_DMA_BUF_SIZE;
860
861 /* Start the RX channel right now */
862 hsu_dma_start_rx_chan(up->rxc, dbuf);
863
864 /* Next init the TX DMA */
865 dbuf = &up->txbuf;
866 dbuf->buf = xmit->buf;
867 dbuf->dma_addr = dma_map_single(port->dev,
868 dbuf->buf,
869 UART_XMIT_SIZE,
870 DMA_TO_DEVICE);
871 dbuf->dma_size = UART_XMIT_SIZE;
872
873 /* This should not be changed all around */
874 chan_writel(up->txc, HSU_CH_BSR, 32);
875 chan_writel(up->txc, HSU_CH_MOTSR, 4);
876 dbuf->ofs = 0;
877 }
878
879exit:
880 /* And clear the interrupt registers again for luck. */
881 (void) serial_in(up, UART_LSR);
882 (void) serial_in(up, UART_RX);
883 (void) serial_in(up, UART_IIR);
884 (void) serial_in(up, UART_MSR);
885
886 up->running = 1;
887 return 0;
888}
889
890static void serial_hsu_shutdown(struct uart_port *port)
891{
892 struct uart_hsu_port *up =
893 container_of(port, struct uart_hsu_port, port);
894 unsigned long flags;
895
896 /* Disable interrupts from this port */
897 up->ier = 0;
898 serial_out(up, UART_IER, 0);
899 up->running = 0;
900
901 spin_lock_irqsave(&up->port.lock, flags);
902 up->port.mctrl &= ~TIOCM_OUT2;
903 serial_hsu_set_mctrl(&up->port, up->port.mctrl);
904 spin_unlock_irqrestore(&up->port.lock, flags);
905
906 /* Disable break condition and FIFOs */
907 serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC);
908 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
909 UART_FCR_CLEAR_RCVR |
910 UART_FCR_CLEAR_XMIT);
911 serial_out(up, UART_FCR, 0);
912}
913
914static void
915serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios,
916 struct ktermios *old)
917{
918 struct uart_hsu_port *up =
919 container_of(port, struct uart_hsu_port, port);
920 struct tty_struct *tty = port->state->port.tty;
921 unsigned char cval, fcr = 0;
922 unsigned long flags;
923 unsigned int baud, quot;
924 u32 mul = 0x3600;
925 u32 ps = 0x10;
926
927 switch (termios->c_cflag & CSIZE) {
928 case CS5:
929 cval = UART_LCR_WLEN5;
930 break;
931 case CS6:
932 cval = UART_LCR_WLEN6;
933 break;
934 case CS7:
935 cval = UART_LCR_WLEN7;
936 break;
937 default:
938 case CS8:
939 cval = UART_LCR_WLEN8;
940 break;
941 }
942
943 /* CMSPAR isn't supported by this driver */
944 if (tty)
945 tty->termios->c_cflag &= ~CMSPAR;
946
947 if (termios->c_cflag & CSTOPB)
948 cval |= UART_LCR_STOP;
949 if (termios->c_cflag & PARENB)
950 cval |= UART_LCR_PARITY;
951 if (!(termios->c_cflag & PARODD))
952 cval |= UART_LCR_EPAR;
953
954 /*
955 * For those basic low baud rate we can get the direct
956 * scalar from 2746800, like 115200 = 2746800/24, for those
957 * higher baud rate, we have to handle them case by case,
958 * but DIV reg is never touched as its default value 0x3d09
959 */
960 baud = uart_get_baud_rate(port, termios, old, 0, 4000000);
961 quot = uart_get_divisor(port, baud);
962
963 switch (baud) {
964 case 3500000:
965 mul = 0x3345;
966 ps = 0xC;
967 quot = 1;
968 break;
969 case 2500000:
970 mul = 0x2710;
971 ps = 0x10;
972 quot = 1;
973 break;
974 case 18432000:
975 mul = 0x2400;
976 ps = 0x10;
977 quot = 1;
978 break;
979 case 1500000:
980 mul = 0x1D4C;
981 ps = 0xc;
982 quot = 1;
983 break;
984 default:
985 ;
986 }
987
988 if ((up->port.uartclk / quot) < (2400 * 16))
989 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_1B;
990 else if ((up->port.uartclk / quot) < (230400 * 16))
991 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_16B;
992 else
993 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_32B;
994
995 fcr |= UART_FCR_HSU_64B_FIFO;
996#ifdef MFD_HSU_A0_STEPPING
997 /* A0 doesn't support half empty IRQ */
998 fcr |= UART_FCR_FULL_EMPT_TXI;
999#endif
1000
1001 /*
1002 * Ok, we're now changing the port state. Do it with
1003 * interrupts disabled.
1004 */
1005 spin_lock_irqsave(&up->port.lock, flags);
1006
1007 /* Update the per-port timeout */
1008 uart_update_timeout(port, termios->c_cflag, baud);
1009
1010 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
1011 if (termios->c_iflag & INPCK)
1012 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
1013 if (termios->c_iflag & (BRKINT | PARMRK))
1014 up->port.read_status_mask |= UART_LSR_BI;
1015
1016 /* Characters to ignore */
1017 up->port.ignore_status_mask = 0;
1018 if (termios->c_iflag & IGNPAR)
1019 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
1020 if (termios->c_iflag & IGNBRK) {
1021 up->port.ignore_status_mask |= UART_LSR_BI;
1022 /*
1023 * If we're ignoring parity and break indicators,
1024 * ignore overruns too (for real raw support).
1025 */
1026 if (termios->c_iflag & IGNPAR)
1027 up->port.ignore_status_mask |= UART_LSR_OE;
1028 }
1029
1030 /* Ignore all characters if CREAD is not set */
1031 if ((termios->c_cflag & CREAD) == 0)
1032 up->port.ignore_status_mask |= UART_LSR_DR;
1033
1034 /*
1035 * CTS flow control flag and modem status interrupts, disable
1036 * MSI by default
1037 */
1038 up->ier &= ~UART_IER_MSI;
1039 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
1040 up->ier |= UART_IER_MSI;
1041
1042 serial_out(up, UART_IER, up->ier);
1043
1044 if (termios->c_cflag & CRTSCTS)
1045 up->mcr |= UART_MCR_AFE | UART_MCR_RTS;
1046 else
1047 up->mcr &= ~UART_MCR_AFE;
1048
1049 serial_out(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */
1050 serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
1051 serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
1052 serial_out(up, UART_LCR, cval); /* reset DLAB */
1053 serial_out(up, UART_MUL, mul); /* set MUL */
1054 serial_out(up, UART_PS, ps); /* set PS */
1055 up->lcr = cval; /* Save LCR */
1056 serial_hsu_set_mctrl(&up->port, up->port.mctrl);
1057 serial_out(up, UART_FCR, fcr);
1058 spin_unlock_irqrestore(&up->port.lock, flags);
1059}
1060
1061static void
1062serial_hsu_pm(struct uart_port *port, unsigned int state,
1063 unsigned int oldstate)
1064{
1065}
1066
1067static void serial_hsu_release_port(struct uart_port *port)
1068{
1069}
1070
1071static int serial_hsu_request_port(struct uart_port *port)
1072{
1073 return 0;
1074}
1075
1076static void serial_hsu_config_port(struct uart_port *port, int flags)
1077{
1078#if 0
1079 struct uart_hsu_port *up =
1080 container_of(port, struct uart_hsu_port, port);
1081 up->port.type = PORT_MFD;
1082#endif
1083}
1084
1085static int
1086serial_hsu_verify_port(struct uart_port *port, struct serial_struct *ser)
1087{
1088 /* We don't want the core code to modify any port params */
1089 return -EINVAL;
1090}
1091
1092static const char *
1093serial_hsu_type(struct uart_port *port)
1094{
1095 struct uart_hsu_port *up =
1096 container_of(port, struct uart_hsu_port, port);
1097 return up->name;
1098}
1099
1100/* Mainly for uart console use */
1101static struct uart_hsu_port *serial_hsu_ports[3];
1102static struct uart_driver serial_hsu_reg;
1103
1104#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
1105
1106#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1107
1108/* Wait for transmitter & holding register to empty */
1109static inline void wait_for_xmitr(struct uart_hsu_port *up)
1110{
1111 unsigned int status, tmout = 1000;
1112
1113 /* Wait up to 1ms for the character to be sent. */
1114 do {
1115 status = serial_in(up, UART_LSR);
1116
1117 if (status & UART_LSR_BI)
1118 up->lsr_break_flag = UART_LSR_BI;
1119
1120 if (--tmout == 0)
1121 break;
1122 udelay(1);
1123 } while (!(status & BOTH_EMPTY));
1124
1125 /* Wait up to 1s for flow control if necessary */
1126 if (up->port.flags & UPF_CONS_FLOW) {
1127 tmout = 1000000;
1128 while (--tmout &&
1129 ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1130 udelay(1);
1131 }
1132}
1133
1134static void serial_hsu_console_putchar(struct uart_port *port, int ch)
1135{
1136 struct uart_hsu_port *up =
1137 container_of(port, struct uart_hsu_port, port);
1138
1139 wait_for_xmitr(up);
1140 serial_out(up, UART_TX, ch);
1141}
1142
1143/*
1144 * Print a string to the serial port trying not to disturb
1145 * any possible real use of the port...
1146 *
1147 * The console_lock must be held when we get here.
1148 */
1149static void
1150serial_hsu_console_write(struct console *co, const char *s, unsigned int count)
1151{
1152 struct uart_hsu_port *up = serial_hsu_ports[co->index];
1153 unsigned long flags;
1154 unsigned int ier;
1155 int locked = 1;
1156
1157 local_irq_save(flags);
1158 if (up->port.sysrq)
1159 locked = 0;
1160 else if (oops_in_progress) {
1161 locked = spin_trylock(&up->port.lock);
1162 } else
1163 spin_lock(&up->port.lock);
1164
1165 /* First save the IER then disable the interrupts */
1166 ier = serial_in(up, UART_IER);
1167 serial_out(up, UART_IER, 0);
1168
1169 uart_console_write(&up->port, s, count, serial_hsu_console_putchar);
1170
1171 /*
1172 * Finally, wait for transmitter to become empty
1173 * and restore the IER
1174 */
1175 wait_for_xmitr(up);
1176 serial_out(up, UART_IER, ier);
1177
1178 if (locked)
1179 spin_unlock(&up->port.lock);
1180 local_irq_restore(flags);
1181}
1182
1183static struct console serial_hsu_console;
1184
1185static int __init
1186serial_hsu_console_setup(struct console *co, char *options)
1187{
1188 struct uart_hsu_port *up;
1189 int baud = 115200;
1190 int bits = 8;
1191 int parity = 'n';
1192 int flow = 'n';
1193 int ret;
1194
1195 if (co->index == -1 || co->index >= serial_hsu_reg.nr)
1196 co->index = 0;
1197 up = serial_hsu_ports[co->index];
1198 if (!up)
1199 return -ENODEV;
1200
1201 if (options)
1202 uart_parse_options(options, &baud, &parity, &bits, &flow);
1203
1204 ret = uart_set_options(&up->port, co, baud, parity, bits, flow);
1205
1206 return ret;
1207}
1208
1209static struct console serial_hsu_console = {
1210 .name = "ttyMFD",
1211 .write = serial_hsu_console_write,
1212 .device = uart_console_device,
1213 .setup = serial_hsu_console_setup,
1214 .flags = CON_PRINTBUFFER,
1215 .index = 2,
1216 .data = &serial_hsu_reg,
1217};
1218#endif
1219
1220struct uart_ops serial_hsu_pops = {
1221 .tx_empty = serial_hsu_tx_empty,
1222 .set_mctrl = serial_hsu_set_mctrl,
1223 .get_mctrl = serial_hsu_get_mctrl,
1224 .stop_tx = serial_hsu_stop_tx,
1225 .start_tx = serial_hsu_start_tx,
1226 .stop_rx = serial_hsu_stop_rx,
1227 .enable_ms = serial_hsu_enable_ms,
1228 .break_ctl = serial_hsu_break_ctl,
1229 .startup = serial_hsu_startup,
1230 .shutdown = serial_hsu_shutdown,
1231 .set_termios = serial_hsu_set_termios,
1232 .pm = serial_hsu_pm,
1233 .type = serial_hsu_type,
1234 .release_port = serial_hsu_release_port,
1235 .request_port = serial_hsu_request_port,
1236 .config_port = serial_hsu_config_port,
1237 .verify_port = serial_hsu_verify_port,
1238};
1239
1240static struct uart_driver serial_hsu_reg = {
1241 .owner = THIS_MODULE,
1242 .driver_name = "MFD serial",
1243 .dev_name = "ttyMFD",
1244 .major = TTY_MAJOR,
1245 .minor = 128,
1246 .nr = 3,
1247};
1248
1249#ifdef CONFIG_PM
1250static int serial_hsu_suspend(struct pci_dev *pdev, pm_message_t state)
1251{
1252 struct uart_hsu_port *up;
1253
1254 up = pci_get_drvdata(pdev);
1255 if (!up)
1256 return 0;
1257
1258 uart_suspend_port(&serial_hsu_reg, &up->port);
1259
1260 return 0;
1261}
1262
1263static int serial_hsu_resume(struct pci_dev *pdev)
1264{
1265 struct uart_hsu_port *up;
1266
1267 up = pci_get_drvdata(pdev);
1268 if (!up)
1269 return 0;
1270 uart_resume_port(&serial_hsu_reg, &up->port);
1271 return 0;
1272}
1273#else
1274#define serial_hsu_suspend NULL
1275#define serial_hsu_resume NULL
1276#endif
1277
1278/* temp global pointer before we settle down on using one or four PCI dev */
1279static struct hsu_port *phsu;
1280
1281static int serial_hsu_probe(struct pci_dev *pdev,
1282 const struct pci_device_id *ent)
1283{
1284 struct uart_hsu_port *uport;
1285 int index, ret;
1286
1287 printk(KERN_INFO "HSU: found PCI Serial controller(ID: %04x:%04x)\n",
1288 pdev->vendor, pdev->device);
1289
1290 switch (pdev->device) {
1291 case 0x081B:
1292 index = 0;
1293 break;
1294 case 0x081C:
1295 index = 1;
1296 break;
1297 case 0x081D:
1298 index = 2;
1299 break;
1300 case 0x081E:
1301 /* internal DMA controller */
1302 index = 3;
1303 break;
1304 default:
1305 dev_err(&pdev->dev, "HSU: out of index!");
1306 return -ENODEV;
1307 }
1308
1309 ret = pci_enable_device(pdev);
1310 if (ret)
1311 return ret;
1312
1313 if (index == 3) {
1314 /* DMA controller */
1315 ret = request_irq(pdev->irq, dma_irq, 0, "hsu_dma", phsu);
1316 if (ret) {
1317 dev_err(&pdev->dev, "can not get IRQ\n");
1318 goto err_disable;
1319 }
1320 pci_set_drvdata(pdev, phsu);
1321 } else {
1322 /* UART port 0~2 */
1323 uport = &phsu->port[index];
1324 uport->port.irq = pdev->irq;
1325 uport->port.dev = &pdev->dev;
1326 uport->dev = &pdev->dev;
1327
1328 ret = request_irq(pdev->irq, port_irq, 0, uport->name, uport);
1329 if (ret) {
1330 dev_err(&pdev->dev, "can not get IRQ\n");
1331 goto err_disable;
1332 }
1333 uart_add_one_port(&serial_hsu_reg, &uport->port);
1334
1335#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE
1336 if (index == 2) {
1337 register_console(&serial_hsu_console);
1338 uport->port.cons = &serial_hsu_console;
1339 }
1340#endif
1341 pci_set_drvdata(pdev, uport);
1342 }
1343
1344 return 0;
1345
1346err_disable:
1347 pci_disable_device(pdev);
1348 return ret;
1349}
1350
1351static void hsu_global_init(void)
1352{
1353 struct hsu_port *hsu;
1354 struct uart_hsu_port *uport;
1355 struct hsu_dma_chan *dchan;
1356 int i, ret;
1357
1358 hsu = kzalloc(sizeof(struct hsu_port), GFP_KERNEL);
1359 if (!hsu)
1360 return;
1361
1362 /* Get basic io resource and map it */
1363 hsu->paddr = 0xffa28000;
1364 hsu->iolen = 0x1000;
1365
1366 if (!(request_mem_region(hsu->paddr, hsu->iolen, "HSU global")))
1367 pr_warning("HSU: error in request mem region\n");
1368
1369 hsu->reg = ioremap_nocache((unsigned long)hsu->paddr, hsu->iolen);
1370 if (!hsu->reg) {
1371 pr_err("HSU: error in ioremap\n");
1372 ret = -ENOMEM;
1373 goto err_free_region;
1374 }
1375
1376 /* Initialise the 3 UART ports */
1377 uport = hsu->port;
1378 for (i = 0; i < 3; i++) {
1379 uport->port.type = PORT_MFD;
1380 uport->port.iotype = UPIO_MEM;
1381 uport->port.mapbase = (resource_size_t)hsu->paddr
1382 + HSU_PORT_REG_OFFSET
1383 + i * HSU_PORT_REG_LENGTH;
1384 uport->port.membase = hsu->reg + HSU_PORT_REG_OFFSET
1385 + i * HSU_PORT_REG_LENGTH;
1386
1387 sprintf(uport->name, "hsu_port%d", i);
1388 uport->port.fifosize = 64;
1389 uport->port.ops = &serial_hsu_pops;
1390 uport->port.line = i;
1391 uport->port.flags = UPF_IOREMAP;
1392 /* make the maxim support rate to 2746800 bps */
1393 uport->port.uartclk = 115200 * 24 * 16;
1394
1395 uport->running = 0;
1396 uport->txc = &hsu->chans[i * 2];
1397 uport->rxc = &hsu->chans[i * 2 + 1];
1398
1399 serial_hsu_ports[i] = uport;
1400 uport->index = i;
1401 uport++;
1402 }
1403
1404 /* Initialise 6 dma channels */
1405 dchan = hsu->chans;
1406 for (i = 0; i < 6; i++) {
1407 dchan->id = i;
1408 dchan->dirt = (i & 0x1) ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
1409 dchan->uport = &hsu->port[i/2];
1410 dchan->reg = hsu->reg + HSU_DMA_CHANS_REG_OFFSET +
1411 i * HSU_DMA_CHANS_REG_LENGTH;
1412 dchan++;
1413 }
1414
1415 phsu = hsu;
1416
1417 hsu_debugfs_init(hsu);
1418 return;
1419
1420err_free_region:
1421 release_mem_region(hsu->paddr, hsu->iolen);
1422 kfree(hsu);
1423 return;
1424}
1425
1426static void serial_hsu_remove(struct pci_dev *pdev)
1427{
1428 struct hsu_port *hsu;
1429 int i;
1430
1431 hsu = pci_get_drvdata(pdev);
1432 if (!hsu)
1433 return;
1434
1435 for (i = 0; i < 3; i++)
1436 uart_remove_one_port(&serial_hsu_reg, &hsu->port[i].port);
1437
1438 pci_set_drvdata(pdev, NULL);
1439 free_irq(hsu->irq, hsu);
1440 pci_disable_device(pdev);
1441}
1442
1443/* First 3 are UART ports, and the 4th is the DMA */
1444static const struct pci_device_id pci_ids[] __devinitdata = {
1445 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081B) },
1446 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081C) },
1447 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081D) },
1448 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081E) },
1449 {},
1450};
1451
1452static struct pci_driver hsu_pci_driver = {
1453 .name = "HSU serial",
1454 .id_table = pci_ids,
1455 .probe = serial_hsu_probe,
1456 .remove = __devexit_p(serial_hsu_remove),
1457 .suspend = serial_hsu_suspend,
1458 .resume = serial_hsu_resume,
1459};
1460
1461static int __init hsu_pci_init(void)
1462{
1463 int ret;
1464
1465 hsu_global_init();
1466
1467 ret = uart_register_driver(&serial_hsu_reg);
1468 if (ret)
1469 return ret;
1470
1471 return pci_register_driver(&hsu_pci_driver);
1472}
1473
1474static void __exit hsu_pci_exit(void)
1475{
1476 pci_unregister_driver(&hsu_pci_driver);
1477 uart_unregister_driver(&serial_hsu_reg);
1478
1479 hsu_debugfs_remove(phsu);
1480
1481 kfree(phsu);
1482}
1483
1484module_init(hsu_pci_init);
1485module_exit(hsu_pci_exit);
1486
1487MODULE_LICENSE("GPL v2");
1488MODULE_ALIAS("platform:medfield-hsu");
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 9ddc866ccc09..f8fce351463d 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -189,6 +189,8 @@
189/* MAX3107 */ 189/* MAX3107 */
190#define PORT_MAX3107 94 190#define PORT_MAX3107 94
191 191
192/* High Speed UART for Medfield */
193#define PORT_MFD 95
192 194
193#ifdef __KERNEL__ 195#ifdef __KERNEL__
194 196
diff --git a/include/linux/serial_mfd.h b/include/linux/serial_mfd.h
new file mode 100644
index 000000000000..2b071e0b034d
--- /dev/null
+++ b/include/linux/serial_mfd.h
@@ -0,0 +1,47 @@
1#ifndef _SERIAL_MFD_H_
2#define _SERIAL_MFD_H_
3
4/* HW register offset definition */
5#define UART_FOR 0x08
6#define UART_PS 0x0C
7#define UART_MUL 0x0D
8#define UART_DIV 0x0E
9
10#define HSU_GBL_IEN 0x0
11#define HSU_GBL_IST 0x4
12
13#define HSU_GBL_INT_BIT_PORT0 0x0
14#define HSU_GBL_INT_BIT_PORT1 0x1
15#define HSU_GBL_INT_BIT_PORT2 0x2
16#define HSU_GBL_INT_BIT_IRI 0x3
17#define HSU_GBL_INT_BIT_HDLC 0x4
18#define HSU_GBL_INT_BIT_DMA 0x5
19
20#define HSU_GBL_ISR 0x8
21#define HSU_GBL_DMASR 0x400
22#define HSU_GBL_DMAISR 0x404
23
24#define HSU_PORT_REG_OFFSET 0x80
25#define HSU_PORT0_REG_OFFSET 0x80
26#define HSU_PORT1_REG_OFFSET 0x100
27#define HSU_PORT2_REG_OFFSET 0x180
28#define HSU_PORT_REG_LENGTH 0x80
29
30#define HSU_DMA_CHANS_REG_OFFSET 0x500
31#define HSU_DMA_CHANS_REG_LENGTH 0x40
32
33#define HSU_CH_SR 0x0 /* channel status reg */
34#define HSU_CH_CR 0x4 /* control reg */
35#define HSU_CH_DCR 0x8 /* descriptor control reg */
36#define HSU_CH_BSR 0x10 /* max fifo buffer size reg */
37#define HSU_CH_MOTSR 0x14 /* minimum ocp transfer size */
38#define HSU_CH_D0SAR 0x20 /* desc 0 start addr */
39#define HSU_CH_D0TSR 0x24 /* desc 0 transfer size */
40#define HSU_CH_D1SAR 0x28
41#define HSU_CH_D1TSR 0x2C
42#define HSU_CH_D2SAR 0x30
43#define HSU_CH_D2TSR 0x34
44#define HSU_CH_D3SAR 0x38
45#define HSU_CH_D3TSR 0x3C
46
47#endif
diff --git a/include/linux/serial_reg.h b/include/linux/serial_reg.h
index cf9327c051ad..c7a0ce11cd47 100644
--- a/include/linux/serial_reg.h
+++ b/include/linux/serial_reg.h
@@ -221,8 +221,24 @@
221#define UART_FCR_PXAR16 0x80 /* receive FIFO threshold = 16 */ 221#define UART_FCR_PXAR16 0x80 /* receive FIFO threshold = 16 */
222#define UART_FCR_PXAR32 0xc0 /* receive FIFO threshold = 32 */ 222#define UART_FCR_PXAR32 0xc0 /* receive FIFO threshold = 32 */
223 223
224/*
225 * Intel MID on-chip HSU (High Speed UART) defined bits
226 */
227#define UART_FCR_HSU_64_1B 0x00 /* receive FIFO treshold = 1 */
228#define UART_FCR_HSU_64_16B 0x40 /* receive FIFO treshold = 16 */
229#define UART_FCR_HSU_64_32B 0x80 /* receive FIFO treshold = 32 */
230#define UART_FCR_HSU_64_56B 0xc0 /* receive FIFO treshold = 56 */
231
232#define UART_FCR_HSU_16_1B 0x00 /* receive FIFO treshold = 1 */
233#define UART_FCR_HSU_16_4B 0x40 /* receive FIFO treshold = 4 */
234#define UART_FCR_HSU_16_8B 0x80 /* receive FIFO treshold = 8 */
235#define UART_FCR_HSU_16_14B 0xc0 /* receive FIFO treshold = 14 */
224 236
237#define UART_FCR_HSU_64B_FIFO 0x20 /* chose 64 bytes FIFO */
238#define UART_FCR_HSU_16B_FIFO 0x00 /* chose 16 bytes FIFO */
225 239
240#define UART_FCR_HALF_EMPT_TXI 0x00 /* trigger TX_EMPT IRQ for half empty */
241#define UART_FCR_FULL_EMPT_TXI 0x08 /* trigger TX_EMPT IRQ for full empty */
226 242
227/* 243/*
228 * These register definitions are for the 16C950 244 * These register definitions are for the 16C950
generated by cgit v1.2.2 (git 2.25.0) at 2025-12-01 06:00:37 -0500