1 files changed, 24 insertions, 22 deletions

diff --git a/drivers/mtd/chips/Kconfig b/drivers/mtd/chips/Kconfig
index baac35339172..35c6a23b183b 100644
--- a/drivers/mtd/chips/Kconfig
+++ b/drivers/mtd/chips/Kconfig
@@ -1,4 +1,5 @@
 menu "RAM/ROM/Flash chip drivers"
+        depends on MTD!=n
 
 config MTD_CFI
         tristate "Detect flash chips by Common Flash Interface (CFI) probe"
@@ -26,10 +27,9 @@ config MTD_JEDECPROBE
 config MTD_GEN_PROBE
         tristate
 
-if MTD_GEN_PROBE
-
 config MTD_CFI_ADV_OPTIONS
         bool "Flash chip driver advanced configuration options"
+        depends on MTD_GEN_PROBE
         help
           If you need to specify a specific endianness for access to flash
           chips, or if you wish to reduce the size of the kernel by including
@@ -39,10 +39,9 @@ config MTD_CFI_ADV_OPTIONS
 
           If unsure, say 'N'.
 
-if MTD_CFI_ADV_OPTIONS
-
 choice
         prompt "Flash cmd/query data swapping"
+        depends on MTD_CFI_ADV_OPTIONS
         default MTD_CFI_NOSWAP
 
 config MTD_CFI_NOSWAP
@@ -73,6 +72,7 @@ endchoice
 
 config MTD_CFI_GEOMETRY
         bool "Specific CFI Flash geometry selection"
+        depends on MTD_CFI_ADV_OPTIONS
         help
           This option does not affect the code directly, but will enable
           some other configuration options which would allow you to reduce
@@ -80,78 +80,81 @@ config MTD_CFI_GEOMETRY
           arrangements of CFI chips. If unsure, say 'N' and all options
           which are supported by the current code will be enabled.
 
-if MTD_CFI_GEOMETRY
-
 config MTD_MAP_BANK_WIDTH_1
-        bool "Support  8-bit buswidth"
+        bool "Support  8-bit buswidth" if MTD_CFI_GEOMETRY
         default y
         help
           If you wish to support CFI devices on a physical bus which is
           8 bits wide, say 'Y'.
 
 config MTD_MAP_BANK_WIDTH_2
-        bool "Support 16-bit buswidth"
+        bool "Support 16-bit buswidth" if MTD_CFI_GEOMETRY
         default y
         help
           If you wish to support CFI devices on a physical bus which is
           16 bits wide, say 'Y'.
 
 config MTD_MAP_BANK_WIDTH_4
-        bool "Support 32-bit buswidth"
+        bool "Support 32-bit buswidth" if MTD_CFI_GEOMETRY
         default y
         help
           If you wish to support CFI devices on a physical bus which is
           32 bits wide, say 'Y'.
 
 config MTD_MAP_BANK_WIDTH_8
-        bool "Support 64-bit buswidth"
+        bool "Support 64-bit buswidth" if MTD_CFI_GEOMETRY
+        default n
         help
           If you wish to support CFI devices on a physical bus which is
           64 bits wide, say 'Y'.
 
 config MTD_MAP_BANK_WIDTH_16
-        bool "Support 128-bit buswidth"
+        bool "Support 128-bit buswidth" if MTD_CFI_GEOMETRY
+        default n
         help
           If you wish to support CFI devices on a physical bus which is
           128 bits wide, say 'Y'.
 
 config MTD_MAP_BANK_WIDTH_32
-        bool "Support 256-bit buswidth"
+        bool "Support 256-bit buswidth" if MTD_CFI_GEOMETRY
+        default n
         help
           If you wish to support CFI devices on a physical bus which is
           256 bits wide, say 'Y'.
 
 config MTD_CFI_I1
-        bool "Support 1-chip flash interleave"
+        bool "Support 1-chip flash interleave" if MTD_CFI_GEOMETRY
         default y
         help
           If your flash chips are not interleaved - i.e. you only have one
           flash chip addressed by each bus cycle, then say 'Y'.
 
 config MTD_CFI_I2
-        bool "Support 2-chip flash interleave"
+        bool "Support 2-chip flash interleave" if MTD_CFI_GEOMETRY
         default y
         help
           If your flash chips are interleaved in pairs - i.e. you have two
           flash chips addressed by each bus cycle, then say 'Y'.
 
 config MTD_CFI_I4
-        bool "Support 4-chip flash interleave"
+        bool "Support 4-chip flash interleave" if MTD_CFI_GEOMETRY
+        default n
         help
           If your flash chips are interleaved in fours - i.e. you have four
           flash chips addressed by each bus cycle, then say 'Y'.
 
 config MTD_CFI_I8
-        bool "Support 8-chip flash interleave"
+        bool "Support 8-chip flash interleave" if MTD_CFI_GEOMETRY
+        default n
         help
           If your flash chips are interleaved in eights - i.e. you have eight
           flash chips addressed by each bus cycle, then say 'Y'.
 
-endif # MTD_CFI_GEOMETRY
-
 config MTD_OTP
         bool "Protection Registers aka one-time programmable (OTP) bits"
+        depends on MTD_CFI_ADV_OPTIONS
         select HAVE_MTD_OTP
+        default n
         help
           This enables support for reading, writing and locking so called
           "Protection Registers" present on some flash chips.
@@ -173,10 +176,9 @@ config MTD_OTP
           This feature should therefore be used with extreme care. Any mistake
           in the programming of OTP bits will waste them.
 
-endif # MTD_CFI_ADV_OPTIONS
-
 config MTD_CFI_INTELEXT
         tristate "Support for Intel/Sharp flash chips"
+        depends on MTD_GEN_PROBE
         select MTD_CFI_UTIL
         help
           The Common Flash Interface defines a number of different command
@@ -186,6 +188,7 @@ config MTD_CFI_INTELEXT
 
 config MTD_CFI_AMDSTD
         tristate "Support for AMD/Fujitsu/Spansion flash chips"
+        depends on MTD_GEN_PROBE
         select MTD_CFI_UTIL
         help
           The Common Flash Interface defines a number of different command
@@ -195,14 +198,13 @@ config MTD_CFI_AMDSTD
 
 config MTD_CFI_STAA
         tristate "Support for ST (Advanced Architecture) flash chips"
+        depends on MTD_GEN_PROBE
         select MTD_CFI_UTIL
         help
           The Common Flash Interface defines a number of different command
           sets which a CFI-compliant chip may claim to implement. This code
           provides support for one of those command sets.
 
-endif # MTD_GEN_PROBE
-
 config MTD_CFI_UTIL
         tristate