6 files changed, 2 insertions, 102 deletions

diff --git a/drivers/ide/alim15x3.c b/drivers/ide/alim15x3.c
index e59b6dee9ae2..0abc43f3101e 100644
--- a/drivers/ide/alim15x3.c
+++ b/drivers/ide/alim15x3.c
@@ -40,16 +40,6 @@
 #define DRV_NAME "alim15x3"
 
 /*
- * Allow UDMA on M1543C-E chipset for WDC disks that ignore CRC checking
- * (this is DANGEROUS and could result in data corruption).
- */
-static int wdc_udma;
-
-module_param(wdc_udma, bool, 0);
-MODULE_PARM_DESC(wdc_udma,
-                 "allow UDMA on M1543C-E chipset for WDC disks (DANGEROUS)");
-
-/*
  *      ALi devices are not plug in. Otherwise these static values would
  *      need to go. They ought to go away anyway
  */
@@ -132,7 +122,7 @@ static u8 ali_udma_filter(ide_drive_t *drive)
         if (m5229_revision > 0x20 && m5229_revision < 0xC2) {
                 if (drive->media != ide_disk)
                         return 0;
-                if (wdc_udma == 0 && chip_is_1543c_e &&
+                if (chip_is_1543c_e &&
                     strstr((char *)&drive->id[ATA_ID_PROD], "WDC "))
                         return 0;
         }
diff --git a/drivers/ide/cmd64x.c b/drivers/ide/cmd64x.c
index ca0c46f6580a..f2500c8826bb 100644
--- a/drivers/ide/cmd64x.c
+++ b/drivers/ide/cmd64x.c
@@ -20,14 +20,6 @@
 
 #define DRV_NAME "cmd64x"
 
-#define CMD_DEBUG 0
-
-#if CMD_DEBUG
-#define cmdprintk(x...) printk(x)
-#else
-#define cmdprintk(x...)
-#endif
-
 /*
  * CMD64x specific registers definition.
  */
@@ -76,9 +68,6 @@ static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_
                 {15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
         static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};
 
-        cmdprintk("program_cycle_times parameters: total=%d, active=%d\n",
-                  cycle_time, active_time);
-
         cycle_count     = quantize_timing( cycle_time, clock_time);
         active_count    = quantize_timing(active_time, clock_time);
         recovery_count  = cycle_count - active_count;
@@ -94,9 +83,6 @@ static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_
         if (active_count > 16)          /* shouldn't actually happen... */
                 active_count = 16;
 
-        cmdprintk("Final counts: total=%d, active=%d, recovery=%d\n",
-                  cycle_count, active_count, recovery_count);
-
         /*
          * Convert values to internal chipset representation
          */
@@ -106,7 +92,6 @@ static void program_cycle_times (ide_drive_t *drive, int cycle_time, int active_
         /* Program the active/recovery counts into the DRWTIM register */
         drwtim = (active_count << 4) | recovery_count;
         (void) pci_write_config_byte(dev, drwtim_regs[drive->dn], drwtim);
-        cmdprintk("Write 0x%02x to reg 0x%x\n", drwtim, drwtim_regs[drive->dn]);
 }
 
 /*
@@ -150,7 +135,6 @@ static void cmd64x_tune_pio(ide_drive_t *drive, const u8 pio)
 
         if (setup_count > 5)            /* shouldn't actually happen... */
                 setup_count = 5;
-        cmdprintk("Final address setup count: %d\n", setup_count);
 
         /*
          * Program the address setup clocks into the ARTTIM registers.
@@ -162,7 +146,6 @@ static void cmd64x_tune_pio(ide_drive_t *drive, const u8 pio)
         arttim &= ~0xc0;
         arttim |= setup_values[setup_count];
         (void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
-        cmdprintk("Write 0x%02x to reg 0x%x\n", arttim, arttim_regs[drive->dn]);
 }
 
 /*
diff --git a/drivers/ide/cy82c693.c b/drivers/ide/cy82c693.c
index 74fc5401f407..d6e2cbbc53a0 100644
--- a/drivers/ide/cy82c693.c
+++ b/drivers/ide/cy82c693.c
@@ -51,11 +51,6 @@
 #define DRV_NAME "cy82c693"
 
 /*
- *      The following are used to debug the driver.
- */
-#define CY82C693_DEBUG_INFO     0
-
-/*
  *      NOTE: the value for busmaster timeout is tricky and I got it by
  *      trial and error!  By using a to low value will cause DMA timeouts
  *      and drop IDE performance, and by using a to high value will cause
@@ -176,11 +171,6 @@ static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
         outb(index, CY82_INDEX_PORT);
         outb(data, CY82_DATA_PORT);
 
-#if CY82C693_DEBUG_INFO
-        printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n",
-                drive->name, hwif->channel, drive->dn & 1, mode & 3, single);
-#endif /* CY82C693_DEBUG_INFO */
-
         /*
          * note: below we set the value for Bus Master IDE TimeOut Register
          * I'm not absolutly sure what this does, but it solved my problem
@@ -194,11 +184,6 @@ static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode)
         data = BUSMASTER_TIMEOUT;
         outb(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT);
         outb(data, CY82_DATA_PORT);
-
-#if CY82C693_DEBUG_INFO
-        printk(KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n",
-                drive->name, data);
-#endif /* CY82C693_DEBUG_INFO */
 }
 
 static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
@@ -239,8 +224,6 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
                 pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r);
                 pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w);
                 pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8);
-
-                addrCtrl &= 0xF;
         } else {
                 /*
                  * set slave drive
@@ -257,17 +240,7 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
                 pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r);
                 pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w);
                 pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8);
-
-                addrCtrl >>= 4;
-                addrCtrl &= 0xF;
         }
-
-#if CY82C693_DEBUG_INFO
-        printk(KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to "
-                "(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n",
-                drive->name, hwif->channel, drive->dn & 1,
-                addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
-#endif /* CY82C693_DEBUG_INFO */
 }
 
 static void __devinit init_iops_cy82c693(ide_hwif_t *hwif)
diff --git a/drivers/ide/pdc202xx_old.c b/drivers/ide/pdc202xx_old.c
index cb812f3700e8..35161dd840a0 100644
--- a/drivers/ide/pdc202xx_old.c
+++ b/drivers/ide/pdc202xx_old.c
@@ -21,8 +21,6 @@
 
 #define DRV_NAME "pdc202xx_old"
 
-#define PDC202XX_DEBUG_DRIVE_INFO       0
-
 static void pdc_old_disable_66MHz_clock(ide_hwif_t *);
 
 static void pdc202xx_set_mode(ide_drive_t *drive, const u8 speed)
@@ -34,11 +32,6 @@ static void pdc202xx_set_mode(ide_drive_t *drive, const u8 speed)
         u8                      AP = 0, BP = 0, CP = 0;
         u8                      TA = 0, TB = 0, TC = 0;
 
-#if PDC202XX_DEBUG_DRIVE_INFO
-        u32                     drive_conf = 0;
-        pci_read_config_dword(dev, drive_pci, &drive_conf);
-#endif
-
         /*
          * TODO: do this once per channel
          */
@@ -89,14 +82,6 @@ static void pdc202xx_set_mode(ide_drive_t *drive, const u8 speed)
                 pci_write_config_byte(dev, drive_pci + 1, BP | TB);
                 pci_write_config_byte(dev, drive_pci + 2, CP | TC);
         }
-
-#if PDC202XX_DEBUG_DRIVE_INFO
-        printk(KERN_DEBUG "%s: %s drive%d 0x%08x ",
-                drive->name, ide_xfer_verbose(speed),
-                drive->dn, drive_conf);
-        pci_read_config_dword(dev, drive_pci, &drive_conf);
-        printk("0x%08x\n", drive_conf);
-#endif
 }
 
 static void pdc202xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
diff --git a/drivers/ide/sis5513.c b/drivers/ide/sis5513.c
index 3b88eba04c9c..468706082fb5 100644
--- a/drivers/ide/sis5513.c
+++ b/drivers/ide/sis5513.c
@@ -632,12 +632,3 @@ module_exit(sis5513_ide_exit);
 MODULE_AUTHOR("Lionel Bouton, L C Chang, Andre Hedrick, Vojtech Pavlik");
 MODULE_DESCRIPTION("PCI driver module for SIS IDE");
 MODULE_LICENSE("GPL");
-
-/*
- * TODO:
- *      - CLEANUP
- *      - More checks in the config registers (force values instead of
- *        relying on the BIOS setting them correctly).
- *      - Further optimisations ?
- *        . for example ATA66+ regs 0x48 & 0x4A
- */
diff --git a/drivers/ide/sl82c105.c b/drivers/ide/sl82c105.c
index d698da470d6f..3c2bbf0057ea 100644
--- a/drivers/ide/sl82c105.c
+++ b/drivers/ide/sl82c105.c
@@ -24,13 +24,6 @@
 
 #define DRV_NAME "sl82c105"
 
-#undef DEBUG
-
-#ifdef DEBUG
-#define DBG(arg) printk arg
-#else
-#define DBG(fmt,...)
-#endif
 /*
  * SL82C105 PCI config register 0x40 bits.
  */
@@ -104,9 +97,6 @@ static void sl82c105_set_dma_mode(ide_drive_t *drive, const u8 speed)
         unsigned long timings = (unsigned long)ide_get_drivedata(drive);
         u16 drv_ctrl;
 
-        DBG(("sl82c105_tune_chipset(drive:%s, speed:%s)\n",
-             drive->name, ide_xfer_verbose(speed)));
-
         drv_ctrl = mwdma_timings[speed - XFER_MW_DMA_0];
 
         /*
@@ -196,8 +186,6 @@ static void sl82c105_dma_start(ide_drive_t *drive)
         struct pci_dev *dev     = to_pci_dev(hwif->dev);
         int reg                 = 0x44 + drive->dn * 4;
 
-        DBG(("%s(drive:%s)\n", __func__, drive->name));
-
         pci_write_config_word(dev, reg,
                               (unsigned long)ide_get_drivedata(drive) >> 16);
 
@@ -209,8 +197,6 @@ static void sl82c105_dma_clear(ide_drive_t *drive)
 {
         struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
 
-        DBG(("sl82c105_dma_clear(drive:%s)\n", drive->name));
-
         sl82c105_reset_host(dev);
 }
 
@@ -218,11 +204,7 @@ static int sl82c105_dma_end(ide_drive_t *drive)
 {
         struct pci_dev *dev     = to_pci_dev(drive->hwif->dev);
         int reg                 = 0x44 + drive->dn * 4;
-        int ret;
-
-        DBG(("%s(drive:%s)\n", __func__, drive->name));
-
-        ret = ide_dma_end(drive);
+        int ret                 = ide_dma_end(drive);
 
         pci_write_config_word(dev, reg,
                               (unsigned long)ide_get_drivedata(drive));
@@ -239,8 +221,6 @@ static void sl82c105_resetproc(ide_drive_t *drive)
         struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
         u32 val;
 
-        DBG(("sl82c105_resetproc(drive:%s)\n", drive->name));
-
         pci_read_config_dword(dev, 0x40, &val);
         val |= (CTRL_P1F16 | CTRL_P0F16);
         pci_write_config_dword(dev, 0x40, val);
@@ -291,8 +271,6 @@ static int init_chipset_sl82c105(struct pci_dev *dev)
 {
         u32 val;
 
-        DBG(("init_chipset_sl82c105()\n"));
-
         pci_read_config_dword(dev, 0x40, &val);
         val |= CTRL_P0EN | CTRL_P0F16 | CTRL_P1F16;
         pci_write_config_dword(dev, 0x40, val);