4 files changed, 283 insertions, 27 deletions

diff --git a/Documentation/cciss.txt b/Documentation/cciss.txt
index 68a711fb82cf..15378422fc46 100644
--- a/Documentation/cciss.txt
+++ b/Documentation/cciss.txt
@@ -133,3 +133,32 @@ hardware and it is important to prevent the kernel from attempting to directly
 access these devices too, as if the array controller were merely a SCSI 
 controller in the same way that we are allowing it to access SCSI tape drives.
 
+SCSI error handling for tape drives and medium changers
+-------------------------------------------------------
+
+The linux SCSI mid layer provides an error handling protocol which
+kicks into gear whenever a SCSI command fails to complete within a
+certain amount of time (which can vary depending on the command).
+The cciss driver participates in this protocol to some extent.  The
+normal protocol is a four step process.  First the device is told
+to abort the command.  If that doesn't work, the device is reset.
+If that doesn't work, the SCSI bus is reset.  If that doesn't work
+the host bus adapter is reset.  Because the cciss driver is a block
+driver as well as a SCSI driver and only the tape drives and medium
+changers are presented to the SCSI mid layer, and unlike more 
+straightforward SCSI drivers, disk i/o continues through the block
+side during the SCSI error recovery process, the cciss driver only
+implements the first two of these actions, aborting the command, and
+resetting the device.  Additionally, most tape drives will not oblige 
+in aborting commands, and sometimes it appears they will not even 
+obey a reset coommand, though in most circumstances they will.  In
+the case that the command cannot be aborted and the device cannot be 
+reset, the device will be set offline.
+
+In the event the error handling code is triggered and a tape drive is
+successfully reset or the tardy command is successfully aborted, the 
+tape drive may still not allow i/o to continue until some command
+is issued which positions the tape to a known position.  Typically you
+must rewind the tape (by issuing "mt -f /dev/st0 rewind" for example)
+before i/o can proceed again to a tape drive which was reset.
+
diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c
index 486b6e1c7dfb..482786068ff9 100644
--- a/drivers/block/cciss.c
+++ b/drivers/block/cciss.c
@@ -148,6 +148,7 @@ static struct board_type products[] = {
 static ctlr_info_t *hba[MAX_CTLR];
 
 static void do_cciss_request(request_queue_t *q);
+static irqreturn_t do_cciss_intr(int irq, void *dev_id, struct pt_regs *regs);
 static int cciss_open(struct inode *inode, struct file *filep);
 static int cciss_release(struct inode *inode, struct file *filep);
 static int cciss_ioctl(struct inode *inode, struct file *filep, 
@@ -1586,6 +1587,24 @@ static int fill_cmd(CommandList_struct *c, __u8 cmd, int ctlr, void *buff,
                 }
         } else if (cmd_type == TYPE_MSG) {
                 switch (cmd) {
+                case 0: /* ABORT message */
+                        c->Request.CDBLen = 12;
+                        c->Request.Type.Attribute = ATTR_SIMPLE;
+                        c->Request.Type.Direction = XFER_WRITE;
+                        c->Request.Timeout = 0;
+                        c->Request.CDB[0] = cmd; /* abort */
+                        c->Request.CDB[1] = 0;   /* abort a command */
+                        /* buff contains the tag of the command to abort */
+                        memcpy(&c->Request.CDB[4], buff, 8);
+                        break;
+                case 1: /* RESET message */
+                        c->Request.CDBLen = 12;
+                        c->Request.Type.Attribute = ATTR_SIMPLE;
+                        c->Request.Type.Direction = XFER_WRITE;
+                        c->Request.Timeout = 0;
+                        memset(&c->Request.CDB[0], 0, sizeof(c->Request.CDB));
+                        c->Request.CDB[0] = cmd;  /* reset */
+                        c->Request.CDB[1] = 0x04; /* reset a LUN */
                 case 3: /* No-Op message */
                         c->Request.CDBLen = 1;
                         c->Request.Type.Attribute = ATTR_SIMPLE;
@@ -1872,6 +1891,52 @@ static unsigned long pollcomplete(int ctlr)
         /* Invalid address to tell caller we ran out of time */
         return 1;
 }
+
+static int add_sendcmd_reject(__u8 cmd, int ctlr, unsigned long complete)
+{
+        /* We get in here if sendcmd() is polling for completions
+           and gets some command back that it wasn't expecting -- 
+           something other than that which it just sent down.  
+           Ordinarily, that shouldn't happen, but it can happen when 
+           the scsi tape stuff gets into error handling mode, and
+           starts using sendcmd() to try to abort commands and 
+           reset tape drives.  In that case, sendcmd may pick up
+           completions of commands that were sent to logical drives
+           through the block i/o system, or cciss ioctls completing, etc. 
+           In that case, we need to save those completions for later
+           processing by the interrupt handler.
+        */
+
+#ifdef CONFIG_CISS_SCSI_TAPE
+        struct sendcmd_reject_list *srl = &hba[ctlr]->scsi_rejects;     
+
+        /* If it's not the scsi tape stuff doing error handling, (abort */
+        /* or reset) then we don't expect anything weird. */
+        if (cmd != CCISS_RESET_MSG && cmd != CCISS_ABORT_MSG) {
+#endif
+                printk( KERN_WARNING "cciss cciss%d: SendCmd "
+                      "Invalid command list address returned! (%lx)\n",
+                        ctlr, complete);
+                /* not much we can do. */
+#ifdef CONFIG_CISS_SCSI_TAPE
+                return 1;
+        }
+
+        /* We've sent down an abort or reset, but something else
+           has completed */
+        if (srl->ncompletions >= (NR_CMDS + 2)) {
+                /* Uh oh.  No room to save it for later... */
+                printk(KERN_WARNING "cciss%d: Sendcmd: Invalid command addr, "
+                        "reject list overflow, command lost!\n", ctlr);
+                return 1;
+        }
+        /* Save it for later */
+        srl->complete[srl->ncompletions] = complete;
+        srl->ncompletions++;
+#endif
+        return 0;
+}
+
 /*
  * Send a command to the controller, and wait for it to complete.  
  * Only used at init time. 
@@ -1894,7 +1959,7 @@ static int sendcmd(
         unsigned long complete;
         ctlr_info_t *info_p= hba[ctlr];
         u64bit buff_dma_handle;
-        int status;
+        int status, done = 0;
 
         if ((c = cmd_alloc(info_p, 1)) == NULL) {
                 printk(KERN_WARNING "cciss: unable to get memory");
@@ -1916,7 +1981,9 @@ resend_cmd1:
         info_p->access.set_intr_mask(info_p, CCISS_INTR_OFF);
         
         /* Make sure there is room in the command FIFO */
-        /* Actually it should be completely empty at this time. */
+        /* Actually it should be completely empty at this time */
+        /* unless we are in here doing error handling for the scsi */
+        /* tape side of the driver. */
         for (i = 200000; i > 0; i--) 
         {
                 /* if fifo isn't full go */
@@ -1933,13 +2000,25 @@ resend_cmd1:
          * Send the cmd
          */
         info_p->access.submit_command(info_p, c);
-        complete = pollcomplete(ctlr);
+        done = 0;
+        do {
+                complete = pollcomplete(ctlr);
 
 #ifdef CCISS_DEBUG
-        printk(KERN_DEBUG "cciss: command completed\n");
+                printk(KERN_DEBUG "cciss: command completed\n");
 #endif /* CCISS_DEBUG */
 
-        if (complete != 1) {
+                if (complete == 1) {
+                        printk( KERN_WARNING
+                                "cciss cciss%d: SendCmd Timeout out, "
+                                "No command list address returned!\n",
+                                ctlr);
+                        status = IO_ERROR;
+                        done = 1;
+                        break;
+                }
+
+                /* This will need to change for direct lookup completions */
                 if ( (complete & CISS_ERROR_BIT)
                      && (complete & ~CISS_ERROR_BIT) == c->busaddr)
                      {
@@ -1979,6 +2058,10 @@ resend_cmd1:
                                                 status = IO_ERROR;
                                                 goto cleanup1;
                                         }
+                                } else if (c->err_info->CommandStatus == CMD_UNABORTABLE) {
+                                        printk(KERN_WARNING "cciss%d: command could not be aborted.\n", ctlr);
+                                        status = IO_ERROR;
+                                        goto cleanup1;
                                 }
                                 printk(KERN_WARNING "ciss ciss%d: sendcmd"
                                 " Error %x \n", ctlr, 
@@ -1993,20 +2076,15 @@ resend_cmd1:
                                 goto cleanup1;
                         }
                 }
+                /* This will need changing for direct lookup completions */
                 if (complete != c->busaddr) {
-                        printk( KERN_WARNING "cciss cciss%d: SendCmd "
-                      "Invalid command list address returned! (%lx)\n",
-                                ctlr, complete);
-                        status = IO_ERROR;
-                        goto cleanup1;
-                }
-        } else {
-                printk( KERN_WARNING
-                        "cciss cciss%d: SendCmd Timeout out, "
-                        "No command list address returned!\n",
-                        ctlr);
-                status = IO_ERROR;
-        }
+                        if (add_sendcmd_reject(cmd, ctlr, complete) != 0) {
+                                BUG(); /* we are pretty much hosed if we get here. */
+                        }
+                        continue;
+                } else
+                        done = 1;
+        } while (!done);
                 
 cleanup1:       
         /* unlock the data buffer from DMA */
@@ -2014,6 +2092,11 @@ cleanup1:
         buff_dma_handle.val32.upper = c->SG[0].Addr.upper;
         pci_unmap_single(info_p->pdev, (dma_addr_t) buff_dma_handle.val,
                                 c->SG[0].Len, PCI_DMA_BIDIRECTIONAL);
+#ifdef CONFIG_CISS_SCSI_TAPE
+        /* if we saved some commands for later, process them now. */
+        if (info_p->scsi_rejects.ncompletions > 0)
+                do_cciss_intr(0, info_p, NULL);
+#endif
         cmd_free(info_p, c, 1);
         return (status);
 } 
@@ -2338,6 +2421,48 @@ startio:
         start_io(h);
 }
 
+static inline unsigned long get_next_completion(ctlr_info_t *h)
+{
+#ifdef CONFIG_CISS_SCSI_TAPE
+        /* Any rejects from sendcmd() lying around? Process them first */
+        if (h->scsi_rejects.ncompletions == 0)
+                return h->access.command_completed(h);
+        else {
+                struct sendcmd_reject_list *srl;
+                int n;
+                srl = &h->scsi_rejects;
+                n = --srl->ncompletions;
+                /* printk("cciss%d: processing saved reject\n", h->ctlr); */
+                printk("p");
+                return srl->complete[n];
+        }
+#else
+        return h->access.command_completed(h);
+#endif
+}
+
+static inline int interrupt_pending(ctlr_info_t *h)
+{
+#ifdef CONFIG_CISS_SCSI_TAPE
+        return ( h->access.intr_pending(h) 
+                || (h->scsi_rejects.ncompletions > 0));
+#else
+        return h->access.intr_pending(h);
+#endif
+}
+
+static inline long interrupt_not_for_us(ctlr_info_t *h)
+{
+#ifdef CONFIG_CISS_SCSI_TAPE
+        return (((h->access.intr_pending(h) == 0) || 
+                 (h->interrupts_enabled == 0)) 
+              && (h->scsi_rejects.ncompletions == 0));
+#else
+        return (((h->access.intr_pending(h) == 0) || 
+                 (h->interrupts_enabled == 0)));
+#endif
+}
+
 static irqreturn_t do_cciss_intr(int irq, void *dev_id, struct pt_regs *regs)
 {
         ctlr_info_t *h = dev_id;
@@ -2347,19 +2472,15 @@ static irqreturn_t do_cciss_intr(int irq, void *dev_id, struct pt_regs *regs)
         int j;
         int start_queue = h->next_to_run;
 
-        /* Is this interrupt for us? */
-        if (( h->access.intr_pending(h) == 0) || (h->interrupts_enabled == 0))
+        if (interrupt_not_for_us(h))
                 return IRQ_NONE;
-
         /*
          * If there are completed commands in the completion queue,
          * we had better do something about it.
          */
         spin_lock_irqsave(CCISS_LOCK(h->ctlr), flags);
-        while( h->access.intr_pending(h))
-        {
-                while((a = h->access.command_completed(h)) != FIFO_EMPTY) 
-                {
+        while (interrupt_pending(h)) {
+                while((a = get_next_completion(h)) != FIFO_EMPTY) {
                         a1 = a;
                         if ((a & 0x04)) {
                                 a2 = (a >> 3);
@@ -2966,7 +3087,15 @@ static int __devinit cciss_init_one(struct pci_dev *pdev,
                 printk( KERN_ERR "cciss: out of memory");
                 goto clean4;
         }
-
+#ifdef CONFIG_CISS_SCSI_TAPE
+        hba[i]->scsi_rejects.complete = 
+                kmalloc(sizeof(hba[i]->scsi_rejects.complete[0]) * 
+                        (NR_CMDS + 5), GFP_KERNEL);
+        if (hba[i]->scsi_rejects.complete == NULL) {
+                printk( KERN_ERR "cciss: out of memory");
+                goto clean4;
+        }
+#endif
         spin_lock_init(&hba[i]->lock);
 
         /* Initialize the pdev driver private data. 
@@ -3034,6 +3163,10 @@ static int __devinit cciss_init_one(struct pci_dev *pdev,
         return(1);
 
 clean4:
+#ifdef CONFIG_CISS_SCSI_TAPE
+        if(hba[i]->scsi_rejects.complete)
+                kfree(hba[i]->scsi_rejects.complete);
+#endif
         if(hba[i]->cmd_pool_bits)
                 kfree(hba[i]->cmd_pool_bits);
         if(hba[i]->cmd_pool)
@@ -3107,6 +3240,9 @@ static void __devexit cciss_remove_one (struct pci_dev *pdev)
         pci_free_consistent(hba[i]->pdev, NR_CMDS * sizeof( ErrorInfo_struct),
                 hba[i]->errinfo_pool, hba[i]->errinfo_pool_dhandle);
         kfree(hba[i]->cmd_pool_bits);
+#ifdef CONFIG_CISS_SCSI_TAPE
+        kfree(hba[i]->scsi_rejects.complete);
+#endif
         release_io_mem(hba[i]);
         free_hba(i);
 }       
diff --git a/drivers/block/cciss.h b/drivers/block/cciss.h
index ef277baee9fd..3b0858c83897 100644
--- a/drivers/block/cciss.h
+++ b/drivers/block/cciss.h
@@ -44,6 +44,14 @@ typedef struct _drive_info_struct
                                   */
 } drive_info_struct;
 
+#ifdef CONFIG_CISS_SCSI_TAPE
+
+struct sendcmd_reject_list {
+        int ncompletions;
+        unsigned long *complete; /* array of NR_CMDS tags */
+};
+
+#endif
 struct ctlr_info 
 {
         int     ctlr;
@@ -100,6 +108,9 @@ struct ctlr_info
         struct gendisk   *gendisk[NWD];
 #ifdef CONFIG_CISS_SCSI_TAPE
         void *scsi_ctlr; /* ptr to structure containing scsi related stuff */
+        /* list of block side commands the scsi error handling sucked up */
+        /* and saved for later processing */
+        struct sendcmd_reject_list scsi_rejects;
 #endif
         unsigned char alive;
 };
diff --git a/drivers/block/cciss_scsi.c b/drivers/block/cciss_scsi.c
index ec27976a57da..3226aa11c6ef 100644
--- a/drivers/block/cciss_scsi.c
+++ b/drivers/block/cciss_scsi.c
@@ -42,6 +42,9 @@
 
 #include "cciss_scsi.h"
 
+#define CCISS_ABORT_MSG 0x00
+#define CCISS_RESET_MSG 0x01
+
 /* some prototypes... */ 
 static int sendcmd(
         __u8    cmd,
@@ -67,6 +70,8 @@ static int cciss_scsi_proc_info(
 
 static int cciss_scsi_queue_command (struct scsi_cmnd *cmd,
                 void (* done)(struct scsi_cmnd *));
+static int cciss_eh_device_reset_handler(struct scsi_cmnd *);
+static int cciss_eh_abort_handler(struct scsi_cmnd *);
 
 static struct cciss_scsi_hba_t ccissscsi[MAX_CTLR] = {
         { .name = "cciss0", .ndevices = 0 },
@@ -90,6 +95,9 @@ static struct scsi_host_template cciss_driver_template = {
         .sg_tablesize           = MAXSGENTRIES,
         .cmd_per_lun            = 1,
         .use_clustering         = DISABLE_CLUSTERING,
+        /* Can't have eh_bus_reset_handler or eh_host_reset_handler for cciss */
+        .eh_device_reset_handler= cciss_eh_device_reset_handler,
+        .eh_abort_handler       = cciss_eh_abort_handler,
 };
 
 #pragma pack(1)
@@ -247,7 +255,7 @@ scsi_cmd_stack_free(int ctlr)
 #define DEVICETYPE(n) (n<0 || n>MAX_SCSI_DEVICE_CODE) ? \
         "Unknown" : scsi_device_types[n]
 
-#if 0
+#if 1
 static int xmargin=8;
 static int amargin=60;
 
@@ -1448,6 +1456,78 @@ cciss_proc_tape_report(int ctlr, unsigned char *buffer, off_t *pos, off_t *len)
         *pos += size; *len += size;
 }
 
+/* Need at least one of these error handlers to keep ../scsi/hosts.c from 
+ * complaining.  Doing a host- or bus-reset can't do anything good here. 
+ * Despite what it might say in scsi_error.c, there may well be commands
+ * on the controller, as the cciss driver registers twice, once as a block
+ * device for the logical drives, and once as a scsi device, for any tape
+ * drives.  So we know there are no commands out on the tape drives, but we
+ * don't know there are no commands on the controller, and it is likely 
+ * that there probably are, as the cciss block device is most commonly used
+ * as a boot device (embedded controller on HP/Compaq systems.)
+*/
+
+static int cciss_eh_device_reset_handler(struct scsi_cmnd *scsicmd)
+{
+        int rc;
+        CommandList_struct *cmd_in_trouble;
+        ctlr_info_t **c;
+        int ctlr;
+
+        /* find the controller to which the command to be aborted was sent */
+        c = (ctlr_info_t **) &scsicmd->device->host->hostdata[0];       
+        if (c == NULL) /* paranoia */
+                return FAILED;
+        ctlr = (*c)->ctlr;
+        printk(KERN_WARNING "cciss%d: resetting tape drive or medium changer.\n", ctlr);
+
+        /* find the command that's giving us trouble */
+        cmd_in_trouble = (CommandList_struct *) scsicmd->host_scribble;
+        if (cmd_in_trouble == NULL) { /* paranoia */
+                return FAILED;
+        }
+        /* send a reset to the SCSI LUN which the command was sent to */
+        rc = sendcmd(CCISS_RESET_MSG, ctlr, NULL, 0, 2, 0, 0, 
+                (unsigned char *) &cmd_in_trouble->Header.LUN.LunAddrBytes[0], 
+                TYPE_MSG);
+        /* sendcmd turned off interrputs on the board, turn 'em back on. */
+        (*c)->access.set_intr_mask(*c, CCISS_INTR_ON);
+        if (rc == 0)
+                return SUCCESS;
+        printk(KERN_WARNING "cciss%d: resetting device failed.\n", ctlr);
+        return FAILED;
+}
+
+static int  cciss_eh_abort_handler(struct scsi_cmnd *scsicmd)
+{
+        int rc;
+        CommandList_struct *cmd_to_abort;
+        ctlr_info_t **c;
+        int ctlr;
+
+        /* find the controller to which the command to be aborted was sent */
+        c = (ctlr_info_t **) &scsicmd->device->host->hostdata[0];       
+        if (c == NULL) /* paranoia */
+                return FAILED;
+        ctlr = (*c)->ctlr;
+        printk(KERN_WARNING "cciss%d: aborting tardy SCSI cmd\n", ctlr);
+
+        /* find the command to be aborted */
+        cmd_to_abort = (CommandList_struct *) scsicmd->host_scribble;
+        if (cmd_to_abort == NULL) /* paranoia */
+                return FAILED;
+        rc = sendcmd(CCISS_ABORT_MSG, ctlr, &cmd_to_abort->Header.Tag, 
+                0, 2, 0, 0, 
+                (unsigned char *) &cmd_to_abort->Header.LUN.LunAddrBytes[0], 
+                TYPE_MSG);
+        /* sendcmd turned off interrputs on the board, turn 'em back on. */
+        (*c)->access.set_intr_mask(*c, CCISS_INTR_ON);
+        if (rc == 0)
+                return SUCCESS;
+        return FAILED;
+
+}
+
 #else /* no CONFIG_CISS_SCSI_TAPE */
 
 /* If no tape support, then these become defined out of existence */