1 files changed, 162 insertions, 26 deletions

diff --git a/drivers/net/e100.c b/drivers/net/e100.c
index 0c37dd97fa09..119dc5300f9d 100644
--- a/drivers/net/e100.c
+++ b/drivers/net/e100.c
@@ -143,6 +143,8 @@
  *      FIXES:
  * 2005/12/02 - Michael O'Donnell <Michael.ODonnell at stratus dot com>
  *      - Stratus87247: protect MDI control register manipulations
+ * 2009/06/01 - Andreas Mohr <andi at lisas dot de>
+ *      - add clean lowlevel I/O emulation for cards with MII-lacking PHYs
  */
 
 #include <linux/module.h>
@@ -372,6 +374,7 @@ enum eeprom_op {
 
 enum eeprom_offsets {
         eeprom_cnfg_mdix  = 0x03,
+        eeprom_phy_iface  = 0x06,
         eeprom_id         = 0x0A,
         eeprom_config_asf = 0x0D,
         eeprom_smbus_addr = 0x90,
@@ -381,6 +384,18 @@ enum eeprom_cnfg_mdix {
         eeprom_mdix_enabled = 0x0080,
 };
 
+enum eeprom_phy_iface {
+        NoSuchPhy = 0,
+        I82553AB,
+        I82553C,
+        I82503,
+        DP83840,
+        S80C240,
+        S80C24,
+        I82555,
+        DP83840A = 10,
+};
+
 enum eeprom_id {
         eeprom_id_wol = 0x0020,
 };
@@ -545,6 +560,7 @@ struct nic {
         u32 msg_enable                          ____cacheline_aligned;
         struct net_device *netdev;
         struct pci_dev *pdev;
+        u16 (*mdio_ctrl)(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data);
 
         struct rx *rxs                          ____cacheline_aligned;
         struct rx *rx_to_use;
@@ -899,7 +915,21 @@ err_unlock:
         return err;
 }
 
-static u16 mdio_ctrl(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data)
+static int mdio_read(struct net_device *netdev, int addr, int reg)
+{
+        struct nic *nic = netdev_priv(netdev);
+        return nic->mdio_ctrl(nic, addr, mdi_read, reg, 0);
+}
+
+static void mdio_write(struct net_device *netdev, int addr, int reg, int data)
+{
+        struct nic *nic = netdev_priv(netdev);
+
+        nic->mdio_ctrl(nic, addr, mdi_write, reg, data);
+}
+
+/* the standard mdio_ctrl() function for usual MII-compliant hardware */
+static u16 mdio_ctrl_hw(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data)
 {
         u32 data_out = 0;
         unsigned int i;
@@ -938,30 +968,83 @@ static u16 mdio_ctrl(struct nic *nic, u32 addr, u32 dir, u32 reg, u16 data)
         return (u16)data_out;
 }
 
-static int mdio_read(struct net_device *netdev, int addr, int reg)
-{
-        return mdio_ctrl(netdev_priv(netdev), addr, mdi_read, reg, 0);
+/* slightly tweaked mdio_ctrl() function for phy_82552_v specifics */
+static u16 mdio_ctrl_phy_82552_v(struct nic *nic,
+                                 u32 addr,
+                                 u32 dir,
+                                 u32 reg,
+                                 u16 data)
+{
+        if ((reg == MII_BMCR) && (dir == mdi_write)) {
+                if (data & (BMCR_ANRESTART | BMCR_ANENABLE)) {
+                        u16 advert = mdio_read(nic->netdev, nic->mii.phy_id,
+                                                        MII_ADVERTISE);
+
+                        /*
+                         * Workaround Si issue where sometimes the part will not
+                         * autoneg to 100Mbps even when advertised.
+                         */
+                        if (advert & ADVERTISE_100FULL)
+                                data |= BMCR_SPEED100 | BMCR_FULLDPLX;
+                        else if (advert & ADVERTISE_100HALF)
+                                data |= BMCR_SPEED100;
+                }
+        }
+        return mdio_ctrl_hw(nic, addr, dir, reg, data);
 }
 
-static void mdio_write(struct net_device *netdev, int addr, int reg, int data)
-{
-        struct nic *nic = netdev_priv(netdev);
-
-        if  ((nic->phy == phy_82552_v) && (reg == MII_BMCR) &&
-             (data & (BMCR_ANRESTART | BMCR_ANENABLE))) {
-                u16 advert = mdio_read(netdev, nic->mii.phy_id, MII_ADVERTISE);
-
-                /*
-                 * Workaround Si issue where sometimes the part will not
-                 * autoneg to 100Mbps even when advertised.
-                 */
-                if (advert & ADVERTISE_100FULL)
-                        data |= BMCR_SPEED100 | BMCR_FULLDPLX;
-                else if (advert & ADVERTISE_100HALF)
-                        data |= BMCR_SPEED100;
+/* Fully software-emulated mdio_ctrl() function for cards without
+ * MII-compliant PHYs.
+ * For now, this is mainly geared towards 80c24 support; in case of further
+ * requirements for other types (i82503, ...?) either extend this mechanism
+ * or split it, whichever is cleaner.
+ */
+static u16 mdio_ctrl_phy_mii_emulated(struct nic *nic,
+                                      u32 addr,
+                                      u32 dir,
+                                      u32 reg,
+                                      u16 data)
+{
+        /* might need to allocate a netdev_priv'ed register array eventually
+         * to be able to record state changes, but for now
+         * some fully hardcoded register handling ought to be ok I guess. */
+
+        if (dir == mdi_read) {
+                switch (reg) {
+                case MII_BMCR:
+                        /* Auto-negotiation, right? */
+                        return  BMCR_ANENABLE |
+                                BMCR_FULLDPLX;
+                case MII_BMSR:
+                        return  BMSR_LSTATUS /* for mii_link_ok() */ |
+                                BMSR_ANEGCAPABLE |
+                                BMSR_10FULL;
+                case MII_ADVERTISE:
+                        /* 80c24 is a "combo card" PHY, right? */
+                        return  ADVERTISE_10HALF |
+                                ADVERTISE_10FULL;
+                default:
+                        DPRINTK(HW, DEBUG,
+                "%s:addr=%d, reg=%d, data=0x%04X: unimplemented emulation!\n",
+                dir == mdi_read ? "READ" : "WRITE", addr, reg, data);
+                        return 0xFFFF;
+                }
+        } else {
+                switch (reg) {
+                default:
+                        DPRINTK(HW, DEBUG,
+                "%s:addr=%d, reg=%d, data=0x%04X: unimplemented emulation!\n",
+                dir == mdi_read ? "READ" : "WRITE", addr, reg, data);
+                        return 0xFFFF;
+                }
         }
-
-        mdio_ctrl(netdev_priv(netdev), addr, mdi_write, reg, data);
+}
+static inline int e100_phy_supports_mii(struct nic *nic)
+{
+        /* for now, just check it by comparing whether we
+           are using MII software emulation.
+        */
+        return (nic->mdio_ctrl != mdio_ctrl_phy_mii_emulated);
 }
 
 static void e100_get_defaults(struct nic *nic)
@@ -1013,7 +1096,8 @@ static void e100_configure(struct nic *nic, struct cb *cb, struct sk_buff *skb)
         config->standard_stat_counter = 0x1;    /* 1=standard, 0=extended */
         config->rx_discard_short_frames = 0x1;  /* 1=discard, 0=pass */
         config->tx_underrun_retry = 0x3;        /* # of underrun retries */
-        config->mii_mode = 0x1;                 /* 1=MII mode, 0=503 mode */
+        if (e100_phy_supports_mii(nic))
+                config->mii_mode = 1;           /* 1=MII mode, 0=i82503 mode */
         config->pad10 = 0x6;
         config->no_source_addr_insertion = 0x1; /* 1=no, 0=yes */
         config->preamble_length = 0x2;          /* 0=1, 1=3, 2=7, 3=15 bytes */
@@ -1270,6 +1354,42 @@ static void e100_dump(struct nic *nic, struct cb *cb, struct sk_buff *skb)
                 offsetof(struct mem, dump_buf));
 }
 
+static int e100_phy_check_without_mii(struct nic *nic)
+{
+        u8 phy_type;
+        int without_mii;
+
+        phy_type = (nic->eeprom[eeprom_phy_iface] >> 8) & 0x0f;
+
+        switch (phy_type) {
+        case NoSuchPhy: /* Non-MII PHY; UNTESTED! */
+        case I82503: /* Non-MII PHY; UNTESTED! */
+        case S80C24: /* Non-MII PHY; tested and working */
+                /* paragraph from the FreeBSD driver, "FXP_PHY_80C24":
+                 * The Seeq 80c24 AutoDUPLEX(tm) Ethernet Interface Adapter
+                 * doesn't have a programming interface of any sort.  The
+                 * media is sensed automatically based on how the link partner
+                 * is configured.  This is, in essence, manual configuration.
+                 */
+                DPRINTK(PROBE, INFO,
+                         "found MII-less i82503 or 80c24 or other PHY\n");
+
+                nic->mdio_ctrl = mdio_ctrl_phy_mii_emulated;
+                nic->mii.phy_id = 0; /* is this ok for an MII-less PHY? */
+
+                /* these might be needed for certain MII-less cards...
+                 * nic->flags |= ich;
+                 * nic->flags |= ich_10h_workaround; */
+
+                without_mii = 1;
+                break;
+        default:
+                without_mii = 0;
+                break;
+        }
+        return without_mii;
+}
+
 #define NCONFIG_AUTO_SWITCH     0x0080
 #define MII_NSC_CONG            MII_RESV1
 #define NSC_CONG_ENABLE         0x0100
@@ -1290,9 +1410,21 @@ static int e100_phy_init(struct nic *nic)
                 if (!((bmcr == 0xFFFF) || ((stat == 0) && (bmcr == 0))))
                         break;
         }
-        DPRINTK(HW, DEBUG, "phy_addr = %d\n", nic->mii.phy_id);
-        if (addr == 32)
-                return -EAGAIN;
+        if (addr == 32) {
+                /* uhoh, no PHY detected: check whether we seem to be some
+                 * weird, rare variant which is *known* to not have any MII.
+                 * But do this AFTER MII checking only, since this does
+                 * lookup of EEPROM values which may easily be unreliable. */
+                if (e100_phy_check_without_mii(nic))
+                        return 0; /* simply return and hope for the best */
+                else {
+                        /* for unknown cases log a fatal error */
+                        DPRINTK(HW, ERR,
+                                "Failed to locate any known PHY, aborting.\n");
+                        return -EAGAIN;
+                }
+        } else
+                DPRINTK(HW, DEBUG, "phy_addr = %d\n", nic->mii.phy_id);
 
         /* Isolate all the PHY ids */
         for (addr = 0; addr < 32; addr++)
@@ -1320,6 +1452,9 @@ static int e100_phy_init(struct nic *nic)
         if (nic->phy == phy_82552_v) {
                 u16 advert = mdio_read(netdev, nic->mii.phy_id, MII_ADVERTISE);
 
+                /* assign special tweaked mdio_ctrl() function */
+                nic->mdio_ctrl = mdio_ctrl_phy_82552_v;
+
                 /* Workaround Si not advertising flow-control during autoneg */
                 advert |= ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM;
                 mdio_write(netdev, nic->mii.phy_id, MII_ADVERTISE, advert);
@@ -2585,6 +2720,7 @@ static int __devinit e100_probe(struct pci_dev *pdev,
         nic->netdev = netdev;
         nic->pdev = pdev;
         nic->msg_enable = (1 << debug) - 1;
+        nic->mdio_ctrl = mdio_ctrl_hw;
         pci_set_drvdata(pdev, netdev);
 
         if ((err = pci_enable_device(pdev))) {