cpupowerutils - cpufrequtils extended with quite some features

CPU power consumption vs performance tuning is no longer
limited to CPU frequency switching anymore: deep sleep states,
traditional dynamic frequency scaling and hidden turbo/boost
frequencies are tied close together and depend on each other.
The first two exist on different architectures like PPC, Itanium and
ARM, the latter (so far) only on X86. On X86 the APU (CPU+GPU) will
only run most efficiently if CPU and GPU has proper power management
in place.

Users and Developers want to have *one* tool to get an overview what
their system supports and to monitor and debug CPU power management
in detail. The tool should compile and work on as many architectures
as possible.

Once this tool stabilizes a bit, it is intended to replace the
Intel-specific tools in tools/power/x86

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>

6 files changed, 503 insertions, 0 deletions

diff --git a/tools/power/cpupower/man/cpupower-frequency-info.1 b/tools/power/cpupower/man/cpupower-frequency-info.1
new file mode 100644
index 000000000000..3194811d58f5
--- /dev/null
+++ b/tools/power/cpupower/man/cpupower-frequency-info.1
@@ -0,0 +1,76 @@
+.TH "cpufreq-info" "1" "0.1" "Mattia Dongili" ""
+.SH "NAME"
+.LP 
+cpufreq\-info \- Utility to retrieve cpufreq kernel information
+.SH "SYNTAX"
+.LP 
+cpufreq\-info [\fIoptions\fP]
+.SH "DESCRIPTION"
+.LP 
+A small tool which prints out cpufreq information helpful to developers and interested users.
+.SH "OPTIONS"
+.LP 
+.TP  
+\fB\-e\fR \fB\-\-debug\fR
+Prints out debug information.
+.TP  
+\fB\-f\fR \fB\-\-freq\fR
+Get frequency the CPU currently runs at, according to the cpufreq core.
+.TP  
+\fB\-w\fR \fB\-\-hwfreq\fR
+Get frequency the CPU currently runs at, by reading it from hardware (only available to root).
+.TP  
+\fB\-l\fR \fB\-\-hwlimits\fR
+Determine the minimum and maximum CPU frequency allowed.
+.TP  
+\fB\-d\fR \fB\-\-driver\fR
+Determines the used cpufreq kernel driver.
+.TP  
+\fB\-p\fR \fB\-\-policy\fR
+Gets the currently used cpufreq policy.
+.TP  
+\fB\-g\fR \fB\-\-governors\fR
+Determines available cpufreq governors.
+.TP  
+\fB\-a\fR \fB\-\-related\-cpus\fR
+Determines which CPUs run at the same hardware frequency.
+.TP  
+\fB\-a\fR \fB\-\-affected\-cpus\fR
+Determines which CPUs need to have their frequency coordinated by software.
+.TP  
+\fB\-s\fR \fB\-\-stats\fR
+Shows cpufreq statistics if available.
+.TP  
+\fB\-y\fR \fB\-\-latency\fR
+Determines the maximum latency on CPU frequency changes.
+.TP  
+\fB\-o\fR \fB\-\-proc\fR
+Prints out information like provided by the /proc/cpufreq interface in 2.4. and early 2.6. kernels.
+.TP  
+\fB\-m\fR \fB\-\-human\fR
+human\-readable output for the \-f, \-w, \-s and \-y parameters.
+.TP  
+\fB\-h\fR \fB\-\-help\fR
+Prints out the help screen.
+.SH "REMARKS"
+.LP 
+By default only values of core zero are displayed. How to display settings of
+other cores is described in the cpupower(1) manpage in the \-\-cpu option section.
+.LP 
+You can't specify more than one of the output specific options \-o \-e \-a \-g \-p \-d \-l \-w \-f \-y.
+.LP 
+You also can't specify the \-o option combined with the \-c option.
+.SH "FILES"
+.nf 
+\fI/sys/devices/system/cpu/cpu*/cpufreq/\fP  
+\fI/proc/cpufreq\fP (deprecated) 
+\fI/proc/sys/cpu/\fP (deprecated)
+.fi 
+.SH "AUTHORS"
+.nf
+Dominik Brodowski <linux@brodo.de> \- author 
+Mattia Dongili<malattia@gmail.com> \- first autolibtoolization
+.fi
+.SH "SEE ALSO"
+.LP 
+cpupower\-frequency\-set(1), cpupower(1)
diff --git a/tools/power/cpupower/man/cpupower-frequency-set.1 b/tools/power/cpupower/man/cpupower-frequency-set.1
new file mode 100644
index 000000000000..26e3e13eee3b
--- /dev/null
+++ b/tools/power/cpupower/man/cpupower-frequency-set.1
@@ -0,0 +1,54 @@
+.TH "cpufreq-set" "1" "0.1" "Mattia Dongili" ""
+.SH "NAME"
+.LP 
+cpufreq\-set \- A small tool which allows to modify cpufreq settings.
+.SH "SYNTAX"
+.LP 
+cpufreq\-set [\fIoptions\fP]
+.SH "DESCRIPTION"
+.LP 
+cpufreq\-set allows you to modify cpufreq settings without having to type e.g. "/sys/devices/system/cpu/cpu0/cpufreq/scaling_set_speed" all the time.
+.SH "OPTIONS"
+.LP 
+.TP 
+\fB\-d\fR \fB\-\-min\fR <FREQ>
+new minimum CPU frequency the governor may select.
+.TP 
+\fB\-u\fR \fB\-\-max\fR <FREQ>
+new maximum CPU frequency the governor may select.
+.TP 
+\fB\-g\fR \fB\-\-governor\fR <GOV>
+new cpufreq governor.
+.TP 
+\fB\-f\fR \fB\-\-freq\fR <FREQ>
+specific frequency to be set. Requires userspace governor to be available and loaded.
+.TP 
+\fB\-r\fR \fB\-\-related\fR
+modify all hardware-related CPUs at the same time
+.TP 
+\fB\-h\fR \fB\-\-help\fR
+Prints out the help screen.
+.SH "REMARKS"
+.LP 
+By default values are applied on all cores. How to modify single core
+configurations is described in the cpupower(1) manpage in the \-\-cpu option section.
+.LP 
+The \-f FREQ, \-\-freq FREQ parameter cannot be combined with any other parameter.
+.LP 
+FREQuencies can be passed in Hz, kHz (default), MHz, GHz, or THz by postfixing the value with the wanted unit name, without any space (frequency in kHz =^ Hz * 0.001 =^ MHz * 1000 =^ GHz * 1000000).
+.LP 
+On Linux kernels up to 2.6.29, the \-r or \-\-related parameter is ignored.
+.SH "FILES" 
+.nf
+\fI/sys/devices/system/cpu/cpu*/cpufreq/\fP  
+\fI/proc/cpufreq\fP (deprecated) 
+\fI/proc/sys/cpu/\fP (deprecated)
+.fi 
+.SH "AUTHORS"
+.nf 
+Dominik Brodowski <linux@brodo.de> \- author 
+Mattia Dongili<malattia@gmail.com> \- first autolibtoolization
+.fi
+.SH "SEE ALSO"
+.LP 
+cpupower\-frequency\-info(1), cpupower(1)
diff --git a/tools/power/cpupower/man/cpupower-info.1 b/tools/power/cpupower/man/cpupower-info.1
new file mode 100644
index 000000000000..58e21196f17f
--- /dev/null
+++ b/tools/power/cpupower/man/cpupower-info.1
@@ -0,0 +1,19 @@
+.TH CPUPOWER\-INFO "1" "22/02/2011" "" "cpupower Manual"
+.SH NAME
+cpupower\-info \- Shows processor power related kernel or hardware configurations
+.SH SYNOPSIS
+.ft B
+.B cpupower info [ \-b ] [ \-s ] [ \-m ]
+
+.SH DESCRIPTION
+\fBcpupower info \fP shows kernel configurations or processor hardware
+registers affecting processor power saving policies.
+
+Some options are platform wide, some affect single cores. By default values
+of core zero are displayed only. cpupower --cpu all cpuinfo will show the
+settings of all cores, see cpupower(1) how to choose specific cores.
+
+.SH "SEE ALSO"
+Options are described in detail in:
+
+cpupower(1), cpupower-set(1)
diff --git a/tools/power/cpupower/man/cpupower-monitor.1 b/tools/power/cpupower/man/cpupower-monitor.1
new file mode 100644
index 000000000000..d5cfa265c3d3
--- /dev/null
+++ b/tools/power/cpupower/man/cpupower-monitor.1
@@ -0,0 +1,179 @@
+.TH CPUPOWER\-MONITOR "1" "22/02/2011" "" "cpupower Manual"
+.SH NAME
+cpupower\-monitor \- Report processor frequency and idle statistics
+.SH SYNOPSIS
+.ft B
+.B cpupower monitor
+.RB "\-l"
+
+.B cpupower monitor
+.RB [ "\-m <mon1>," [ "<mon2>,..." ] ]
+.RB [ "\-i seconds" ]
+.br
+.B cpupower monitor
+.RB [ "\-m <mon1>," [ "<mon2>,..." ] ]
+.RB command
+.br
+.SH DESCRIPTION
+\fBcpupower-monitor \fP reports processor topology, frequency and idle power
+state statistics. Either \fBcommand\fP is forked and
+statistics are printed upon its completion, or statistics are printed periodically.
+
+\fBcpupower-monitor \fP implements independent processor sleep state and
+frequency counters. Some are retrieved from kernel statistics, some are
+directly reading out hardware registers. Use \-l to get an overview which are
+supported on your system.
+
+.SH Options
+.PP
+\-l
+.RS 4
+List available monitors on your system. Additional details about each monitor
+are shown:
+.RS 2
+.IP \(bu
+The name in quotation marks which can be passed to the \-m parameter.
+.IP \(bu
+The number of different counters the monitor supports in brackets.
+.IP \(bu
+The amount of time in seconds the counters might overflow, due to
+implementation constraints.
+.IP \(bu
+The name and a description of each counter and its processor hierarchy level
+coverage in square brackets:
+.RS 4
+.IP \(bu
+[T] \-> Thread
+.IP \(bu
+[C] \-> Core
+.IP \(bu
+[P] \-> Processor Package (Socket)
+.IP \(bu
+[M] \-> Machine/Platform wide counter
+.RE
+.RE
+.RE
+.PP
+\-m <mon1>,<mon2>,...
+.RS 4
+Only display specific monitors. Use the monitor string(s) provided by \-l option.
+.RE
+.PP
+\-i seconds
+.RS 4
+Measure intervall.
+.RE
+.PP
+command
+.RS 4
+Measure idle and frequency characteristics of an arbitrary command/workload.
+The executable \fBcommand\fP is forked and upon its exit, statistics gathered since it was
+forked are displayed.
+.RE
+.PP
+\-v
+.RS 4
+Increase verbosity if the binary was compiled with the DEBUG option set.
+.RE
+
+.SH MONITOR DESCRIPTIONS
+.SS "Idle_Stats"
+Shows statistics of the cpuidle kernel subsystem. Values are retrieved from
+/sys/devices/system/cpu/cpu*/cpuidle/state*/.
+The kernel updates these values every time an idle state is entered or
+left. Therefore there can be some inaccuracy when cores are in an idle
+state for some time when the measure starts or ends. In worst case it can happen
+that one core stayed in an idle state for the whole measure time and the idle
+state usage time as exported by the kernel did not get updated. In this case
+a state residency of 0 percent is shown while it was 100.
+
+.SS "Mperf"
+The name comes from the aperf/mperf (average and maximum) MSR registers used
+which are available on recent X86 processors. It shows the average frequency
+(including boost frequencies).
+The fact that on all recent hardware the mperf timer stops ticking in any idle
+state it is also used to show C0 (processor is active) and Cx (processor is in
+any sleep state) times. These counters do not have the inaccuracy restrictions
+the "Idle_Stats" counters may show.
+May work poorly on Linux-2.6.20 through 2.6.29, as the \fBacpi-cpufreq \fP
+kernel frequency driver periodically cleared aperf/mperf registers in those
+kernels.
+
+.SS "Nehalem" "SandyBridge"
+Intel Core and Package sleep state counters.
+Threads (hyperthreaded cores) may not be able to enter deeper core states if
+its sibling is utilized.
+Deepest package sleep states may in reality show up as machine/platform wide
+sleep states and can only be entered if all cores are idle. Look up Intel
+manuals (some are provided in the References section) for further details.
+
+.SS "Ontario" "Liano"
+AMD laptop and desktop processor (family 12h and 14h) sleep state counters.
+The registers are accessed via PCI and therefore can still be read out while
+cores have been offlined.
+
+There is one special counter: NBP1 (North Bridge P1).
+This one always returns 0 or 1, depending on whether the North Bridge P1
+power state got entered at least once during measure time.
+Being able to enter NBP1 state also depends on graphics power management.
+Therefore this counter can be used to verify whether the graphics' driver
+power management is working as expected.
+
+.SH EXAMPLES
+
+cpupower monitor -l" may show:
+.RS 4
+Monitor "Mperf" (3 states) \- Might overflow after 922000000 s
+
+   ...
+
+Monitor "Idle_Stats" (3 states) \- Might overflow after 4294967295 s
+
+   ...
+
+.RE
+cpupower monitor \-m "Idle_Stats,Mperf" scp /tmp/test /nfs/tmp
+
+Monitor the scp command, show both Mperf and Idle_Stats states counter
+statistics, but in exchanged order.
+
+
+
+.RE
+Be careful that the typical command to fully utilize one CPU by doing:
+
+cpupower monitor cat /dev/zero >/dev/null
+
+Does not work as expected, because the measured output is redirected to
+/dev/null. This could get workarounded by putting the line into an own, tiny
+shell script. Hit CTRL\-c to terminate the command and get the measure output
+displayed.
+
+.SH REFERENCES
+"BIOS and Kernel Developer’s Guide (BKDG) for AMD Family 14h Processors"
+http://support.amd.com/us/Processor_TechDocs/43170.pdf
+
+"Intel® Turbo Boost Technology
+in Intel® Core™ Microarchitecture (Nehalem) Based Processors"
+http://download.intel.com/design/processor/applnots/320354.pdf
+
+"Intel® 64 and IA-32 Architectures Software Developer's Manual
+Volume 3B: System Programming Guide"
+http://www.intel.com/products/processor/manuals
+
+.SH FILES
+.ta
+.nf
+/dev/cpu/*/msr
+/sys/devices/system/cpu/cpu*/cpuidle/state*/.
+.fi
+
+.SH "SEE ALSO"
+powertop(8), msr(4), vmstat(8)
+.PP
+.SH AUTHORS
+.nf
+Written by Thomas Renninger <trenn@suse.de>
+
+Nehalem, SandyBridge monitors and command passing
+based on turbostat.8 from Len Brown <len.brown@intel.com>
diff --git a/tools/power/cpupower/man/cpupower-set.1 b/tools/power/cpupower/man/cpupower-set.1
new file mode 100644
index 000000000000..c4954a9fe4e7
--- /dev/null
+++ b/tools/power/cpupower/man/cpupower-set.1
@@ -0,0 +1,103 @@
+.TH CPUPOWER\-SET "1" "22/02/2011" "" "cpupower Manual"
+.SH NAME
+cpupower\-set \- Set processor power related kernel or hardware configurations
+.SH SYNOPSIS
+.ft B
+.B cpupower set [ \-b VAL ] [ \-s VAL ] [ \-m VAL ]
+
+
+.SH DESCRIPTION
+\fBcpupower set \fP sets kernel configurations or directly accesses hardware
+registers affecting processor power saving policies.
+
+Some options are platform wide, some affect single cores. By default values
+are applied on all cores. How to modify single core configurations is
+described in the cpupower(1) manpage in the \-\-cpu option section. Whether an
+option affects the whole system or can be applied to individual cores is
+described in the Options sections.
+
+Use \fBcpupower info \fP to read out current settings and whether they are
+supported on the system at all.
+
+.SH Options
+.PP
+\-\-perf-bias, \-b
+.RS 4
+Sets a register on supported Intel processore which allows software to convey
+its policy for the relative importance of performance versus energy savings to
+the  processor.
+
+The range of valid numbers is 0-15, where 0 is maximum
+performance and 15 is maximum energy efficiency.
+
+The processor uses this information in model-specific ways
+when it must select trade-offs between performance and
+energy efficiency.
+
+This policy hint does not supersede Processor Performance states
+(P-states) or CPU Idle power states (C-states), but allows
+software to have influence where it would otherwise be unable
+to express a preference.
+
+For example, this setting may tell the hardware how
+aggressively or conservatively to control frequency
+in the "turbo range" above the explicitly OS-controlled
+P-state frequency range.  It may also tell the hardware
+how aggressively it should enter the OS requested C-states.
+
+This option can be applied to individual cores only via the \-\-cpu option,
+cpupower(1).
+
+Setting the performance bias value on one CPU can modify the setting on
+related CPUs as well (for example all CPUs on one socket), because of
+hardware restrictions.
+Use \fBcpupower -c all info -b\fP to verify.
+
+This options needs the msr kernel driver (CONFIG_X86_MSR) loaded.
+.RE
+.PP
+\-\-sched\-mc,  \-m [ VAL ]
+.RE
+\-\-sched\-smt, \-s [ VAL ]
+.RS 4
+\-\-sched\-mc utilizes cores in one processor package/socket first before
+processes are scheduled to other processor packages/sockets.
+
+\-\-sched\-smt utilizes thread siblings of one processor core first before
+processes are scheduled to other cores.
+
+The impact on power consumption and performance (positiv or negativ) heavily
+depends on processor support for deep sleep states, frequency scaling and
+frequency boost modes and their dependencies between other thread siblings
+and processor cores.
+
+Taken over from kernel documentation:
+
+Adjust the kernel's multi-core scheduler support.
+
+Possible values are:
+.RS 2
+0 - No power saving load balance (default value)
+
+1 - Fill one thread/core/package first for long running threads
+
+2 - Also bias task wakeups to semi-idle cpu package for power
+savings
+.RE
+
+sched_mc_power_savings is dependent upon SCHED_MC, which is
+itself architecture dependent.
+
+sched_smt_power_savings is dependent upon SCHED_SMT, which
+is itself architecture dependent.
+
+The two files are independent of each other. It is possible
+that one file may be present without the other.
+
+.SH "SEE ALSO"
+cpupower-info(1), cpupower-monitor(1), powertop(1)
+.PP
+.SH AUTHORS
+.nf
+\-\-perf\-bias parts written by Len Brown <len.brown@intel.com>
+Thomas Renninger <trenn@suse.de>
diff --git a/tools/power/cpupower/man/cpupower.1 b/tools/power/cpupower/man/cpupower.1
new file mode 100644
index 000000000000..78c20feab85c
--- /dev/null
+++ b/tools/power/cpupower/man/cpupower.1
@@ -0,0 +1,72 @@
+.TH CPUPOWER "1" "07/03/2011" "" "cpupower Manual"
+.SH NAME
+cpupower \- Shows and sets processor power related values
+.SH SYNOPSIS
+.ft B
+.B cpupower [ \-c cpulist ] subcommand [ARGS]
+
+.B cpupower \-v|\-\-version
+
+.B cpupower \-h|\-\-help
+
+.SH DESCRIPTION
+\fBcpupower \fP is a collection of tools to examine and tune power saving
+related features of your processor.
+
+The manpages of the subcommands (cpupower\-<subcommand>(1)) provide detailed
+descriptions of supported features. Run \fBcpupower help\fP to get an overview
+of supported subcommands.
+
+.SH Options
+.PP
+\-\-help, \-h
+.RS 4
+Shows supported subcommands and general usage.
+.RE
+.PP
+\-\-cpu cpulist,  \-c cpulist
+.RS 4
+Only show or set values for specific cores.
+This option is not supported by all subcommands, details can be found in the
+manpages of the subcommands.
+
+Some subcommands access all cores (typically the *\-set commands), some only
+the first core (typically the *\-info commands) by default.
+
+The syntax for <cpulist> is based on how the kernel exports CPU bitmasks via
+sysfs files. Some examples:
+.RS 4
+.TP 16
+Input
+Equivalent to
+.TP
+all
+all cores
+.TP
+0\-3
+0,1,2,3
+.TP
+0\-7:2
+0,2,4,6
+.TP
+1,3,5-7
+1,3,5,6,7
+.TP
+0\-3:2,8\-15:4
+0,2,8,12        
+.RE
+.RE
+.PP
+\-\-version,  \-v
+.RS 4
+Print the package name and version number.
+
+.SH "SEE ALSO"
+cpupower-set(1), cpupower-info(1), cpupower-idle(1),
+cpupower-frequency-set(1), cpupower-frequency-info(1), cpupower-monitor(1),
+powertop(1)
+.PP
+.SH AUTHORS
+.nf
+\-\-perf\-bias parts written by Len Brown <len.brown@intel.com>
+Thomas Renninger <trenn@suse.de>