[NET]: move config options out to individual protocols

Move the protocol specific config options out to the specific protocols.
With this change net/Kconfig now starts to become readable and serve as a
good basis for further re-structuring.

The menu structure is left almost intact, except that indention is
fixed in most cases. Most visible are the INET changes where several
"depends on INET" are replaced with a single ifdef INET / endif pair.

Several new files were created to accomplish this change - they are
small but serve the purpose that config options are now distributed
out where they belongs.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

17 files changed, 447 insertions, 452 deletions

diff --git a/net/8021q/Kconfig b/net/8021q/Kconfig
new file mode 100644
index 000000000000..c4a382e450e2
--- /dev/null
+++ b/net/8021q/Kconfig
@@ -0,0 +1,19 @@
+#
+# Configuration for 802.1Q VLAN support
+#
+
+config VLAN_8021Q
+        tristate "802.1Q VLAN Support"
+        ---help---
+          Select this and you will be able to create 802.1Q VLAN interfaces
+          on your ethernet interfaces.  802.1Q VLAN supports almost
+          everything a regular ethernet interface does, including
+          firewalling, bridging, and of course IP traffic.  You will need
+          the 'vconfig' tool from the VLAN project in order to effectively
+          use VLANs.  See the VLAN web page for more information:
+          <http://www.candelatech.com/~greear/vlan.html>
+
+          To compile this code as a module, choose M here: the module
+          will be called 8021q.
+
+          If unsure, say N.
diff --git a/net/Kconfig b/net/Kconfig
index f46fc326c00b..2684e809a649 100644
--- a/net/Kconfig
+++ b/net/Kconfig
@@ -22,57 +22,14 @@ config NET
           recommended to read the NET-HOWTO, available from
           <http://www.tldp.org/docs.html#howto>.
 
-menu "Networking options"
-        depends on NET
-
-config PACKET
-        tristate "Packet socket"
-        ---help---
-          The Packet protocol is used by applications which communicate
-          directly with network devices without an intermediate network
-          protocol implemented in the kernel, e.g. tcpdump.  If you want them
-          to work, choose Y.
-
-          To compile this driver as a module, choose M here: the module will
-          be called af_packet.
-
-          If unsure, say Y.
+# Make sure that all config symbols are dependent on NET
+if NET
 
-config PACKET_MMAP
-        bool "Packet socket: mmapped IO"
-        depends on PACKET
-        help
-          If you say Y here, the Packet protocol driver will use an IO
-          mechanism that results in faster communication.
-
-          If unsure, say N.
-
-config UNIX
-        tristate "Unix domain sockets"
-        ---help---
-          If you say Y here, you will include support for Unix domain sockets;
-          sockets are the standard Unix mechanism for establishing and
-          accessing network connections.  Many commonly used programs such as
-          the X Window system and syslog use these sockets even if your
-          machine is not connected to any network.  Unless you are working on
-          an embedded system or something similar, you therefore definitely
-          want to say Y here.
-
-          To compile this driver as a module, choose M here: the module will be
-          called unix.  Note that several important services won't work
-          correctly if you say M here and then neglect to load the module.
-
-          Say Y unless you know what you are doing.
-
-config NET_KEY
-        tristate "PF_KEY sockets"
-        select XFRM
-        ---help---
-          PF_KEYv2 socket family, compatible to KAME ones.
-          They are required if you are going to use IPsec tools ported
-          from KAME.
+menu "Networking options"
 
-          Say Y unless you know what you are doing.
+source "net/packet/Kconfig"
+source "net/unix/Kconfig"
+source "net/xfrm/Kconfig"
 
 config INET
         bool "TCP/IP networking"
@@ -96,30 +53,12 @@ config INET
 
           Short answer: say Y.
 
+if INET
 source "net/ipv4/Kconfig"
-
-#   IPv6 as module will cause a CRASH if you try to unload it
-config IPV6
-        tristate "The IPv6 protocol"
-        depends on INET
-        default m
-        select CRYPTO if IPV6_PRIVACY
-        select CRYPTO_MD5 if IPV6_PRIVACY
-        ---help---
-          This is complemental support for the IP version 6.
-          You will still be able to do traditional IPv4 networking as well.
-
-          For general information about IPv6, see
-          <http://playground.sun.com/pub/ipng/html/ipng-main.html>.
-          For Linux IPv6 development information, see <http://www.linux-ipv6.org>.
-          For specific information about IPv6 under Linux, read the HOWTO at
-          <http://www.bieringer.de/linux/IPv6/>.
-
-          To compile this protocol support as a module, choose M here: the 
-          module will be called ipv6.
-
 source "net/ipv6/Kconfig"
 
+endif # if INET
+
 menuconfig NETFILTER
         bool "Network packet filtering (replaces ipchains)"
         ---help---
@@ -208,269 +147,16 @@ source "net/bridge/netfilter/Kconfig"
 
 endif
 
-config XFRM
-       bool
-       depends on NET
-
-source "net/xfrm/Kconfig"
-
 source "net/sctp/Kconfig"
-
-config ATM
-        tristate "Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)"
-        depends on EXPERIMENTAL
-        ---help---
-          ATM is a high-speed networking technology for Local Area Networks
-          and Wide Area Networks.  It uses a fixed packet size and is
-          connection oriented, allowing for the negotiation of minimum
-          bandwidth requirements.
-
-          In order to participate in an ATM network, your Linux box needs an
-          ATM networking card. If you have that, say Y here and to the driver
-          of your ATM card below.
-
-          Note that you need a set of user-space programs to actually make use
-          of ATM.  See the file <file:Documentation/networking/atm.txt> for
-          further details.
-
-config ATM_CLIP
-        tristate "Classical IP over ATM (EXPERIMENTAL)"
-        depends on ATM && INET
-        help
-          Classical IP over ATM for PVCs and SVCs, supporting InARP and
-          ATMARP. If you want to communication with other IP hosts on your ATM
-          network, you will typically either say Y here or to "LAN Emulation
-          (LANE)" below.
-
-config ATM_CLIP_NO_ICMP
-        bool "Do NOT send ICMP if no neighbour (EXPERIMENTAL)"
-        depends on ATM_CLIP
-        help
-          Normally, an "ICMP host unreachable" message is sent if a neighbour
-          cannot be reached because there is no VC to it in the kernel's
-          ATMARP table. This may cause problems when ATMARP table entries are
-          briefly removed during revalidation. If you say Y here, packets to
-          such neighbours are silently discarded instead.
-
-config ATM_LANE
-        tristate "LAN Emulation (LANE) support (EXPERIMENTAL)"
-        depends on ATM
-        help
-          LAN Emulation emulates services of existing LANs across an ATM
-          network. Besides operating as a normal ATM end station client, Linux
-          LANE client can also act as an proxy client bridging packets between
-          ELAN and Ethernet segments. You need LANE if you want to try MPOA.
-
-config ATM_MPOA
-        tristate "Multi-Protocol Over ATM (MPOA) support (EXPERIMENTAL)"
-        depends on ATM && INET && ATM_LANE!=n
-        help
-          Multi-Protocol Over ATM allows ATM edge devices such as routers,
-          bridges and ATM attached hosts establish direct ATM VCs across
-          subnetwork boundaries. These shortcut connections bypass routers
-          enhancing overall network performance.
-
-config ATM_BR2684
-        tristate "RFC1483/2684 Bridged protocols"
-        depends on ATM && INET
-        help
-          ATM PVCs can carry ethernet PDUs according to RFC2684 (formerly 1483)
-          This device will act like an ethernet from the kernels point of view,
-          with the traffic being carried by ATM PVCs (currently 1 PVC/device).
-          This is sometimes used over DSL lines.  If in doubt, say N.
-
-config ATM_BR2684_IPFILTER
-        bool "Per-VC IP filter kludge"
-        depends on ATM_BR2684
-        help
-          This is an experimental mechanism for users who need to terminate a
-          large number of IP-only vcc's.  Do not enable this unless you are sure
-          you know what you are doing.
-
-config BRIDGE
-        tristate "802.1d Ethernet Bridging"
-        ---help---
-          If you say Y here, then your Linux box will be able to act as an
-          Ethernet bridge, which means that the different Ethernet segments it
-          is connected to will appear as one Ethernet to the participants.
-          Several such bridges can work together to create even larger
-          networks of Ethernets using the IEEE 802.1 spanning tree algorithm.
-          As this is a standard, Linux bridges will cooperate properly with
-          other third party bridge products.
-
-          In order to use the Ethernet bridge, you'll need the bridge
-          configuration tools; see <file:Documentation/networking/bridge.txt>
-          for location. Please read the Bridge mini-HOWTO for more
-          information.
-
-          If you enable iptables support along with the bridge support then you
-          turn your bridge into a bridging IP firewall.
-          iptables will then see the IP packets being bridged, so you need to
-          take this into account when setting up your firewall rules.
-          Enabling arptables support when bridging will let arptables see
-          bridged ARP traffic in the arptables FORWARD chain.
-
-          To compile this code as a module, choose M here: the module
-          will be called bridge.
-
-          If unsure, say N.
-
-config VLAN_8021Q
-        tristate "802.1Q VLAN Support"
-        ---help---
-          Select this and you will be able to create 802.1Q VLAN interfaces
-          on your ethernet interfaces.  802.1Q VLAN supports almost
-          everything a regular ethernet interface does, including
-          firewalling, bridging, and of course IP traffic.  You will need
-          the 'vconfig' tool from the VLAN project in order to effectively
-          use VLANs.  See the VLAN web page for more information:
-          <http://www.candelatech.com/~greear/vlan.html>
-
-          To compile this code as a module, choose M here: the module
-          will be called 8021q.
-
-          If unsure, say N.
-
-config DECNET
-        tristate "DECnet Support"
-        ---help---
-          The DECnet networking protocol was used in many products made by
-          Digital (now Compaq).  It provides reliable stream and sequenced
-          packet communications over which run a variety of services similar
-          to those which run over TCP/IP.
-
-          To find some tools to use with the kernel layer support, please
-          look at Patrick Caulfield's web site:
-          <http://linux-decnet.sourceforge.net/>.
-
-          More detailed documentation is available in
-          <file:Documentation/networking/decnet.txt>.
-
-          Be sure to say Y to "/proc file system support" and "Sysctl support"
-          below when using DECnet, since you will need sysctl support to aid
-          in configuration at run time.
-
-          The DECnet code is also available as a module ( = code which can be
-          inserted in and removed from the running kernel whenever you want).
-          The module is called decnet.
-
+source "net/atm/Kconfig"
+source "net/bridge/Kconfig"
+source "net/8021q/Kconfig"
 source "net/decnet/Kconfig"
-
 source "net/llc/Kconfig"
-
-config IPX
-        tristate "The IPX protocol"
-        select LLC
-        ---help---
-          This is support for the Novell networking protocol, IPX, commonly
-          used for local networks of Windows machines.  You need it if you
-          want to access Novell NetWare file or print servers using the Linux
-          Novell client ncpfs (available from
-          <ftp://platan.vc.cvut.cz/pub/linux/ncpfs/>) or from
-          within the Linux DOS emulator DOSEMU (read the DOSEMU-HOWTO,
-          available from <http://www.tldp.org/docs.html#howto>).  In order
-          to do the former, you'll also have to say Y to "NCP file system
-          support", below.
-
-          IPX is similar in scope to IP, while SPX, which runs on top of IPX,
-          is similar to TCP. There is also experimental support for SPX in
-          Linux (see "SPX networking", below).
-
-          To turn your Linux box into a fully featured NetWare file server and
-          IPX router, say Y here and fetch either lwared from
-          <ftp://ibiblio.org/pub/Linux/system/network/daemons/> or
-          mars_nwe from <ftp://www.compu-art.de/mars_nwe/>. For more
-          information, read the IPX-HOWTO available from
-          <http://www.tldp.org/docs.html#howto>.
-
-          General information about how to connect Linux, Windows machines and
-          Macs is on the WWW at <http://www.eats.com/linux_mac_win.html>.
-
-          The IPX driver would enlarge your kernel by about 16 KB. To compile
-          this driver as a module, choose M here: the module will be called ipx.
-          Unless you want to integrate your Linux box with a local Novell
-          network, say N.
-
 source "net/ipx/Kconfig"
-
-config ATALK
-        tristate "Appletalk protocol support"
-        select LLC
-        ---help---
-          AppleTalk is the protocol that Apple computers can use to communicate
-          on a network.  If your Linux box is connected to such a network and you
-          wish to connect to it, say Y.  You will need to use the netatalk package
-          so that your Linux box can act as a print and file server for Macs as
-          well as access AppleTalk printers.  Check out
-          <http://www.zettabyte.net/netatalk/> on the WWW for details.
-          EtherTalk is the name used for AppleTalk over Ethernet and the
-          cheaper and slower LocalTalk is AppleTalk over a proprietary Apple
-          network using serial links.  EtherTalk and LocalTalk are fully
-          supported by Linux.
-
-          General information about how to connect Linux, Windows machines and
-          Macs is on the WWW at <http://www.eats.com/linux_mac_win.html>.  The
-          NET-3-HOWTO, available from
-          <http://www.tldp.org/docs.html#howto>, contains valuable
-          information as well.
-
-          To compile this driver as a module, choose M here: the module will be
-          called appletalk. You almost certainly want to compile it as a
-          module so you can restart your AppleTalk stack without rebooting
-          your machine. I hear that the GNU boycott of Apple is over, so
-          even politically correct people are allowed to say Y here.
-
 source "drivers/net/appletalk/Kconfig"
-
-config X25
-        tristate "CCITT X.25 Packet Layer (EXPERIMENTAL)"
-        depends on EXPERIMENTAL
-        ---help---
-          X.25 is a set of standardized network protocols, similar in scope to
-          frame relay; the one physical line from your box to the X.25 network
-          entry point can carry several logical point-to-point connections
-          (called "virtual circuits") to other computers connected to the X.25
-          network. Governments, banks, and other organizations tend to use it
-          to connect to each other or to form Wide Area Networks (WANs). Many
-          countries have public X.25 networks. X.25 consists of two
-          protocols: the higher level Packet Layer Protocol (PLP) (say Y here
-          if you want that) and the lower level data link layer protocol LAPB
-          (say Y to "LAPB Data Link Driver" below if you want that).
-
-          You can read more about X.25 at <http://www.sangoma.com/x25.htm> and
-          <http://www.cisco.com/univercd/cc/td/doc/product/software/ios11/cbook/cx25.htm>.
-          Information about X.25 for Linux is contained in the files
-          <file:Documentation/networking/x25.txt> and
-          <file:Documentation/networking/x25-iface.txt>.
-
-          One connects to an X.25 network either with a dedicated network card
-          using the X.21 protocol (not yet supported by Linux) or one can do
-          X.25 over a standard telephone line using an ordinary modem (say Y
-          to "X.25 async driver" below) or over Ethernet using an ordinary
-          Ethernet card and the LAPB over Ethernet (say Y to "LAPB Data Link
-          Driver" and "LAPB over Ethernet driver" below).
-
-          To compile this driver as a module, choose M here: the module
-          will be called x25. If unsure, say N.
-
-config LAPB
-        tristate "LAPB Data Link Driver (EXPERIMENTAL)"
-        depends on EXPERIMENTAL
-        ---help---
-          Link Access Procedure, Balanced (LAPB) is the data link layer (i.e.
-          the lower) part of the X.25 protocol. It offers a reliable
-          connection service to exchange data frames with one other host, and
-          it is used to transport higher level protocols (mostly X.25 Packet
-          Layer, the higher part of X.25, but others are possible as well).
-          Usually, LAPB is used with specialized X.21 network cards, but Linux
-          currently supports LAPB only over Ethernet connections. If you want
-          to use LAPB connections over Ethernet, say Y here and to "LAPB over
-          Ethernet driver" below. Read
-          <file:Documentation/networking/lapb-module.txt> for technical
-          details.
-
-          To compile this driver as a module, choose M here: the
-          module will be called lapb.  If unsure, say N.
+source "net/x25/Kconfig"
+source "net/lapb/Kconfig"
 
 config NET_DIVERT
         bool "Frame Diverter (EXPERIMENTAL)"
@@ -498,107 +184,10 @@ config NET_DIVERT
 
           If unsure, say N.
 
-config ECONET
-        tristate "Acorn Econet/AUN protocols (EXPERIMENTAL)"
-        depends on EXPERIMENTAL && INET
-        ---help---
-          Econet is a fairly old and slow networking protocol mainly used by
-          Acorn computers to access file and print servers. It uses native
-          Econet network cards. AUN is an implementation of the higher level
-          parts of Econet that runs over ordinary Ethernet connections, on
-          top of the UDP packet protocol, which in turn runs on top of the
-          Internet protocol IP.
-
-          If you say Y here, you can choose with the next two options whether
-          to send Econet/AUN traffic over a UDP Ethernet connection or over
-          a native Econet network card.
-
-          To compile this driver as a module, choose M here: the module
-          will be called econet.
-
-config ECONET_AUNUDP
-        bool "AUN over UDP"
-        depends on ECONET
-        help
-          Say Y here if you want to send Econet/AUN traffic over a UDP
-          connection (UDP is a packet based protocol that runs on top of the
-          Internet protocol IP) using an ordinary Ethernet network card.
-
-config ECONET_NATIVE
-        bool "Native Econet"
-        depends on ECONET
-        help
-          Say Y here if you have a native Econet network card installed in
-          your computer.
-
-config WAN_ROUTER
-        tristate "WAN router"
-        depends on EXPERIMENTAL
-        ---help---
-          Wide Area Networks (WANs), such as X.25, frame relay and leased
-          lines, are used to interconnect Local Area Networks (LANs) over vast
-          distances with data transfer rates significantly higher than those
-          achievable with commonly used asynchronous modem connections.
-          Usually, a quite expensive external device called a `WAN router' is
-          needed to connect to a WAN.
-
-          As an alternative, WAN routing can be built into the Linux kernel.
-          With relatively inexpensive WAN interface cards available on the
-          market, a perfectly usable router can be built for less than half
-          the price of an external router.  If you have one of those cards and
-          wish to use your Linux box as a WAN router, say Y here and also to
-          the WAN driver for your card, below.  You will then need the
-          wan-tools package which is available from <ftp://ftp.sangoma.com/>.
-          Read <file:Documentation/networking/wan-router.txt> for more
-          information.
-
-          To compile WAN routing support as a module, choose M here: the
-          module will be called wanrouter.
-
-          If unsure, say N.
-
-menu "QoS and/or fair queueing"
-
-config NET_SCHED
-        bool "QoS and/or fair queueing"
-        ---help---
-          When the kernel has several packets to send out over a network
-          device, it has to decide which ones to send first, which ones to
-          delay, and which ones to drop. This is the job of the packet
-          scheduler, and several different algorithms for how to do this
-          "fairly" have been proposed.
-
-          If you say N here, you will get the standard packet scheduler, which
-          is a FIFO (first come, first served). If you say Y here, you will be
-          able to choose from among several alternative algorithms which can
-          then be attached to different network devices. This is useful for
-          example if some of your network devices are real time devices that
-          need a certain minimum data flow rate, or if you need to limit the
-          maximum data flow rate for traffic which matches specified criteria.
-          This code is considered to be experimental.
-
-          To administer these schedulers, you'll need the user-level utilities
-          from the package iproute2+tc at <ftp://ftp.tux.org/pub/net/ip-routing/>.
-          That package also contains some documentation; for more, check out
-          <http://snafu.freedom.org/linux2.2/iproute-notes.html>.
-
-          This Quality of Service (QoS) support will enable you to use
-          Differentiated Services (diffserv) and Resource Reservation Protocol
-          (RSVP) on your Linux router if you also say Y to "QoS support",
-          "Packet classifier API" and to some classifiers below. Documentation
-          and software is at <http://diffserv.sourceforge.net/>.
-
-          If you say Y here and to "/proc file system" below, you will be able
-          to read status information about packet schedulers from the file
-          /proc/net/psched.
-
-          The available schedulers are listed in the following questions; you
-          can say Y to as many as you like. If unsure, say N now.
-
+source "net/econet/Kconfig"
+source "net/wanrouter/Kconfig"
 source "net/sched/Kconfig"
 
-endmenu
-
 menu "Network testing"
 
 config NET_PKTGEN
@@ -637,10 +226,9 @@ config NET_POLL_CONTROLLER
         def_bool NETPOLL
 
 source "net/ax25/Kconfig"
-
 source "net/irda/Kconfig"
-
 source "net/bluetooth/Kconfig"
 
+endif   # if NET
 endmenu # Networking
 
diff --git a/net/atm/Kconfig b/net/atm/Kconfig
new file mode 100644
index 000000000000..bea2426229b1
--- /dev/null
+++ b/net/atm/Kconfig
@@ -0,0 +1,74 @@
+#
+# Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)
+#
+
+config ATM
+        tristate "Asynchronous Transfer Mode (ATM) (EXPERIMENTAL)"
+        depends on EXPERIMENTAL
+        ---help---
+          ATM is a high-speed networking technology for Local Area Networks
+          and Wide Area Networks.  It uses a fixed packet size and is
+          connection oriented, allowing for the negotiation of minimum
+          bandwidth requirements.
+
+          In order to participate in an ATM network, your Linux box needs an
+          ATM networking card. If you have that, say Y here and to the driver
+          of your ATM card below.
+
+          Note that you need a set of user-space programs to actually make use
+          of ATM.  See the file <file:Documentation/networking/atm.txt> for
+          further details.
+
+config ATM_CLIP
+        tristate "Classical IP over ATM (EXPERIMENTAL)"
+        depends on ATM && INET
+        help
+          Classical IP over ATM for PVCs and SVCs, supporting InARP and
+          ATMARP. If you want to communication with other IP hosts on your ATM
+          network, you will typically either say Y here or to "LAN Emulation
+          (LANE)" below.
+
+config ATM_CLIP_NO_ICMP
+        bool "Do NOT send ICMP if no neighbour (EXPERIMENTAL)"
+        depends on ATM_CLIP
+        help
+          Normally, an "ICMP host unreachable" message is sent if a neighbour
+          cannot be reached because there is no VC to it in the kernel's
+          ATMARP table. This may cause problems when ATMARP table entries are
+          briefly removed during revalidation. If you say Y here, packets to
+          such neighbours are silently discarded instead.
+
+config ATM_LANE
+        tristate "LAN Emulation (LANE) support (EXPERIMENTAL)"
+        depends on ATM
+        help
+          LAN Emulation emulates services of existing LANs across an ATM
+          network. Besides operating as a normal ATM end station client, Linux
+          LANE client can also act as an proxy client bridging packets between
+          ELAN and Ethernet segments. You need LANE if you want to try MPOA.
+
+config ATM_MPOA
+        tristate "Multi-Protocol Over ATM (MPOA) support (EXPERIMENTAL)"
+        depends on ATM && INET && ATM_LANE!=n
+        help
+          Multi-Protocol Over ATM allows ATM edge devices such as routers,
+          bridges and ATM attached hosts establish direct ATM VCs across
+          subnetwork boundaries. These shortcut connections bypass routers
+          enhancing overall network performance.
+
+config ATM_BR2684
+        tristate "RFC1483/2684 Bridged protocols"
+        depends on ATM && INET
+        help
+          ATM PVCs can carry ethernet PDUs according to rfc2684 (formerly 1483)
+          This device will act like an ethernet from the kernels point of view,
+          with the traffic being carried by ATM PVCs (currently 1 PVC/device).
+          This is sometimes used over DSL lines.  If in doubt, say N.
+
+config ATM_BR2684_IPFILTER
+        bool "Per-VC IP filter kludge"
+        depends on ATM_BR2684
+        help
+          This is an experimental mechanism for users who need to terminating a
+          large number of IP-only vcc's.  Do not enable this unless you are sure
+          you know what you are doing.
diff --git a/net/bridge/Kconfig b/net/bridge/Kconfig
new file mode 100644
index 000000000000..db23d59746cf
--- /dev/null
+++ b/net/bridge/Kconfig
@@ -0,0 +1,31 @@
+#
+# 802.1d Ethernet Bridging
+#
+
+config BRIDGE
+        tristate "802.1d Ethernet Bridging"
+        ---help---
+          If you say Y here, then your Linux box will be able to act as an
+          Ethernet bridge, which means that the different Ethernet segments it
+          is connected to will appear as one Ethernet to the participants.
+          Several such bridges can work together to create even larger
+          networks of Ethernets using the IEEE 802.1 spanning tree algorithm.
+          As this is a standard, Linux bridges will cooperate properly with
+          other third party bridge products.
+
+          In order to use the Ethernet bridge, you'll need the bridge
+          configuration tools; see <file:Documentation/networking/bridge.txt>
+          for location. Please read the Bridge mini-HOWTO for more
+          information.
+
+          If you enable iptables support along with the bridge support then you
+          turn your bridge into a bridging IP firewall.
+          iptables will then see the IP packets being bridged, so you need to
+          take this into account when setting up your firewall rules.
+          Enabling arptables support when bridging will let arptables see
+          bridged ARP traffic in the arptables FORWARD chain.
+
+          To compile this code as a module, choose M here: the module
+          will be called bridge.
+
+          If unsure, say N.
diff --git a/net/decnet/Kconfig b/net/decnet/Kconfig
index 2101da542ba8..92f2ec46fd22 100644
--- a/net/decnet/Kconfig
+++ b/net/decnet/Kconfig
@@ -1,6 +1,29 @@
 #
 # DECnet configuration
 #
+config DECNET
+        tristate "DECnet Support"
+        ---help---
+          The DECnet networking protocol was used in many products made by
+          Digital (now Compaq).  It provides reliable stream and sequenced
+          packet communications over which run a variety of services similar
+          to those which run over TCP/IP.
+
+          To find some tools to use with the kernel layer support, please
+          look at Patrick Caulfield's web site:
+          <http://linux-decnet.sourceforge.net/>.
+
+          More detailed documentation is available in
+          <file:Documentation/networking/decnet.txt>.
+
+          Be sure to say Y to "/proc file system support" and "Sysctl support"
+          below when using DECnet, since you will need sysctl support to aid
+          in configuration at run time.
+
+          The DECnet code is also available as a module ( = code which can be
+          inserted in and removed from the running kernel whenever you want).
+          The module is called decnet.
+
 config DECNET_ROUTER
         bool "DECnet: router support (EXPERIMENTAL)"
         depends on DECNET && EXPERIMENTAL
diff --git a/net/econet/Kconfig b/net/econet/Kconfig
new file mode 100644
index 000000000000..39a2d2975e0e
--- /dev/null
+++ b/net/econet/Kconfig
@@ -0,0 +1,36 @@
+#
+# Acorn Econet/AUN protocols 
+#
+
+config ECONET
+        tristate "Acorn Econet/AUN protocols (EXPERIMENTAL)"
+        depends on EXPERIMENTAL && INET
+        ---help---
+          Econet is a fairly old and slow networking protocol mainly used by
+          Acorn computers to access file and print servers. It uses native
+          Econet network cards. AUN is an implementation of the higher level
+          parts of Econet that runs over ordinary Ethernet connections, on
+          top of the UDP packet protocol, which in turn runs on top of the
+          Internet protocol IP.
+
+          If you say Y here, you can choose with the next two options whether
+          to send Econet/AUN traffic over a UDP Ethernet connection or over
+          a native Econet network card.
+
+          To compile this driver as a module, choose M here: the module
+          will be called econet.
+
+config ECONET_AUNUDP
+        bool "AUN over UDP"
+        depends on ECONET
+        help
+          Say Y here if you want to send Econet/AUN traffic over a UDP
+          connection (UDP is a packet based protocol that runs on top of the
+          Internet protocol IP) using an ordinary Ethernet network card.
+
+config ECONET_NATIVE
+        bool "Native Econet"
+        depends on ECONET
+        help
+          Say Y here if you have a native Econet network card installed in
+          your computer.
diff --git a/net/ipv4/Kconfig b/net/ipv4/Kconfig
index 3e63123f7bbd..df5386885a90 100644
--- a/net/ipv4/Kconfig
+++ b/net/ipv4/Kconfig
@@ -3,7 +3,6 @@
 #
 config IP_MULTICAST
         bool "IP: multicasting"
-        depends on INET
         help
           This is code for addressing several networked computers at once,
           enlarging your kernel by about 2 KB. You need multicasting if you
@@ -17,7 +16,6 @@ config IP_MULTICAST
 
 config IP_ADVANCED_ROUTER
         bool "IP: advanced router"
-        depends on INET
         ---help---
           If you intend to run your Linux box mostly as a router, i.e. as a
           computer that forwards and redistributes network packets, say Y; you
@@ -183,7 +181,6 @@ config IP_ROUTE_VERBOSE
 
 config IP_PNP
         bool "IP: kernel level autoconfiguration"
-        depends on INET
         help
           This enables automatic configuration of IP addresses of devices and
           of the routing table during kernel boot, based on either information
@@ -242,7 +239,6 @@ config IP_PNP_RARP
 #   bool '    IP: ARP support' CONFIG_IP_PNP_ARP                
 config NET_IPIP
         tristate "IP: tunneling"
-        depends on INET
         select INET_TUNNEL
         ---help---
           Tunneling means encapsulating data of one protocol type within
@@ -260,7 +256,6 @@ config NET_IPIP
 
 config NET_IPGRE
         tristate "IP: GRE tunnels over IP"
-        depends on INET
         select XFRM
         help
           Tunneling means encapsulating data of one protocol type within
@@ -319,7 +314,7 @@ config IP_PIMSM_V2
 
 config ARPD
         bool "IP: ARP daemon support (EXPERIMENTAL)"
-        depends on INET && EXPERIMENTAL
+        depends on EXPERIMENTAL
         ---help---
           Normally, the kernel maintains an internal cache which maps IP
           addresses to hardware addresses on the local network, so that
@@ -344,7 +339,6 @@ config ARPD
 
 config SYN_COOKIES
         bool "IP: TCP syncookie support (disabled per default)"
-        depends on INET
         ---help---
           Normal TCP/IP networking is open to an attack known as "SYN
           flooding". This denial-of-service attack prevents legitimate remote
@@ -381,7 +375,6 @@ config SYN_COOKIES
 
 config INET_AH
         tristate "IP: AH transformation"
-        depends on INET
         select XFRM
         select CRYPTO
         select CRYPTO_HMAC
@@ -394,7 +387,6 @@ config INET_AH
 
 config INET_ESP
         tristate "IP: ESP transformation"
-        depends on INET
         select XFRM
         select CRYPTO
         select CRYPTO_HMAC
@@ -408,7 +400,6 @@ config INET_ESP
 
 config INET_IPCOMP
         tristate "IP: IPComp transformation"
-        depends on INET
         select XFRM
         select INET_TUNNEL
         select CRYPTO
@@ -421,7 +412,6 @@ config INET_IPCOMP
 
 config INET_TUNNEL
         tristate "IP: tunnel transformation"
-        depends on INET
         select XFRM
         ---help---
           Support for generic IP tunnel transformation, which is required by
@@ -431,7 +421,6 @@ config INET_TUNNEL
 
 config IP_TCPDIAG
         tristate "IP: TCP socket monitoring interface"
-        depends on INET
         default y
         ---help---
           Support for TCP socket monitoring interface used by native Linux
@@ -447,7 +436,6 @@ config IP_TCPDIAG_IPV6
 
 config TCP_CONG_ADVANCED
         bool "TCP: advanced congestion control"
-        depends on INET
         ---help---
           Support for selection of various TCP congestion control
           modules.
@@ -463,7 +451,6 @@ menu "TCP congestion control"
 
 config TCP_CONG_BIC
         tristate "Binary Increase Congestion (BIC) control"
-        depends on INET
         default y
         ---help---
         BIC-TCP is a sender-side only change that ensures a linear RTT
@@ -478,7 +465,6 @@ config TCP_CONG_BIC
 
 config TCP_CONG_WESTWOOD
         tristate "TCP Westwood+"
-        depends on INET
         default m
         ---help---
         TCP Westwood+ is a sender-side only modification of the TCP Reno
@@ -493,7 +479,6 @@ config TCP_CONG_WESTWOOD
 
 config TCP_CONG_HTCP
         tristate "H-TCP"
-        depends on INET
         default m
         ---help---
         H-TCP is a send-side only modifications of the TCP Reno
@@ -505,7 +490,7 @@ config TCP_CONG_HTCP
 
 config TCP_CONG_HSTCP
         tristate "High Speed TCP"
-        depends on INET && EXPERIMENTAL
+        depends on EXPERIMENTAL
         default n
         ---help---
         Sally Floyd's High Speed TCP (RFC 3649) congestion control.
@@ -516,7 +501,7 @@ config TCP_CONG_HSTCP
 
 config TCP_CONG_HYBLA
         tristate "TCP-Hybla congestion control algorithm"
-        depends on INET && EXPERIMENTAL
+        depends on EXPERIMENTAL
         default n
         ---help---
         TCP-Hybla is a sender-side only change that eliminates penalization of
@@ -526,7 +511,7 @@ config TCP_CONG_HYBLA
 
 config TCP_CONG_VEGAS
         tristate "TCP Vegas"
-        depends on INET && EXPERIMENTAL
+        depends on EXPERIMENTAL
         default n
         ---help---
         TCP Vegas is a sender-side only change to TCP that anticipates
@@ -537,7 +522,7 @@ config TCP_CONG_VEGAS
 
 config TCP_CONG_SCALABLE
         tristate "Scalable TCP"
-        depends on INET && EXPERIMENTAL
+        depends on EXPERIMENTAL
         default n
         ---help---
         Scalable TCP is a sender-side only change to TCP which uses a
diff --git a/net/ipv4/ipvs/Kconfig b/net/ipv4/ipvs/Kconfig
index 63a82b4b64bb..c9820bfc493a 100644
--- a/net/ipv4/ipvs/Kconfig
+++ b/net/ipv4/ipvs/Kconfig
@@ -2,11 +2,11 @@
 # IP Virtual Server configuration
 #
 menu    "IP: Virtual Server Configuration"
-        depends on INET && NETFILTER
+        depends on NETFILTER
 
 config  IP_VS
         tristate "IP virtual server support (EXPERIMENTAL)"
-        depends on INET && NETFILTER
+        depends on NETFILTER
         ---help---
           IP Virtual Server support will let you build a high-performance
           virtual server based on cluster of two or more real servers. This
diff --git a/net/ipv6/Kconfig b/net/ipv6/Kconfig
index e66ca9381cfd..95163cd52ae0 100644
--- a/net/ipv6/Kconfig
+++ b/net/ipv6/Kconfig
@@ -1,6 +1,26 @@
 #
 # IPv6 configuration
-# 
+#
+
+#   IPv6 as module will cause a CRASH if you try to unload it
+config IPV6
+        tristate "The IPv6 protocol"
+        default m
+        select CRYPTO if IPV6_PRIVACY
+        select CRYPTO_MD5 if IPV6_PRIVACY
+        ---help---
+          This is complemental support for the IP version 6.
+          You will still be able to do traditional IPv4 networking as well.
+
+          For general information about IPv6, see
+          <http://playground.sun.com/pub/ipng/html/ipng-main.html>.
+          For Linux IPv6 development information, see <http://www.linux-ipv6.org>.
+          For specific information about IPv6 under Linux, read the HOWTO at
+          <http://www.bieringer.de/linux/IPv6/>.
+
+          To compile this protocol support as a module, choose M here: the 
+          module will be called ipv6.
+
 config IPV6_PRIVACY
         bool "IPv6: Privacy Extensions (RFC 3041) support"
         depends on IPV6
diff --git a/net/ipx/Kconfig b/net/ipx/Kconfig
index a16237c0e783..980a826f5d02 100644
--- a/net/ipx/Kconfig
+++ b/net/ipx/Kconfig
@@ -1,6 +1,39 @@
 #
 # IPX configuration
 #
+config IPX
+        tristate "The IPX protocol"
+        select LLC
+        ---help---
+          This is support for the Novell networking protocol, IPX, commonly
+          used for local networks of Windows machines.  You need it if you
+          want to access Novell NetWare file or print servers using the Linux
+          Novell client ncpfs (available from
+          <ftp://platan.vc.cvut.cz/pub/linux/ncpfs/>) or from
+          within the Linux DOS emulator DOSEMU (read the DOSEMU-HOWTO,
+          available from <http://www.tldp.org/docs.html#howto>).  In order
+          to do the former, you'll also have to say Y to "NCP file system
+          support", below.
+
+          IPX is similar in scope to IP, while SPX, which runs on top of IPX,
+          is similar to TCP. There is also experimental support for SPX in
+          Linux (see "SPX networking", below).
+
+          To turn your Linux box into a fully featured NetWare file server and
+          IPX router, say Y here and fetch either lwared from
+          <ftp://ibiblio.org/pub/Linux/system/network/daemons/> or
+          mars_nwe from <ftp://www.compu-art.de/mars_nwe/>. For more
+          information, read the IPX-HOWTO available from
+          <http://www.tldp.org/docs.html#howto>.
+
+          General information about how to connect Linux, Windows machines and
+          Macs is on the WWW at <http://www.eats.com/linux_mac_win.html>.
+
+          The IPX driver would enlarge your kernel by about 16 KB. To compile
+          this driver as a module, choose M here: the module will be called ipx.
+          Unless you want to integrate your Linux box with a local Novell
+          network, say N.
+
 config IPX_INTERN
         bool "IPX: Full internal IPX network"
         depends on IPX
diff --git a/net/lapb/Kconfig b/net/lapb/Kconfig
new file mode 100644
index 000000000000..f0b5efb31a00
--- /dev/null
+++ b/net/lapb/Kconfig
@@ -0,0 +1,22 @@
+#
+# LAPB Data Link Drive
+#
+
+config LAPB
+        tristate "LAPB Data Link Driver (EXPERIMENTAL)"
+        depends on EXPERIMENTAL
+        ---help---
+          Link Access Procedure, Balanced (LAPB) is the data link layer (i.e.
+          the lower) part of the X.25 protocol. It offers a reliable
+          connection service to exchange data frames with one other host, and
+          it is used to transport higher level protocols (mostly X.25 Packet
+          Layer, the higher part of X.25, but others are possible as well).
+          Usually, LAPB is used with specialized X.21 network cards, but Linux
+          currently supports LAPB only over Ethernet connections. If you want
+          to use LAPB connections over Ethernet, say Y here and to "LAPB over
+          Ethernet driver" below. Read
+          <file:Documentation/networking/lapb-module.txt> for technical
+          details.
+
+          To compile this driver as a module, choose M here: the
+          module will be called lapb.  If unsure, say N.
diff --git a/net/packet/Kconfig b/net/packet/Kconfig
new file mode 100644
index 000000000000..34ff93ff894d
--- /dev/null
+++ b/net/packet/Kconfig
@@ -0,0 +1,26 @@
+#
+# Packet configuration
+#
+
+config PACKET
+        tristate "Packet socket"
+        ---help---
+          The Packet protocol is used by applications which communicate
+          directly with network devices without an intermediate network
+          protocol implemented in the kernel, e.g. tcpdump.  If you want them
+          to work, choose Y.
+
+          To compile this driver as a module, choose M here: the module will
+          be called af_packet.
+
+          If unsure, say Y.
+
+config PACKET_MMAP
+        bool "Packet socket: mmapped IO"
+        depends on PACKET
+        help
+          If you say Y here, the Packet protocol driver will use an IO
+          mechanism that results in faster communication.
+
+          If unsure, say N.
+
diff --git a/net/sched/Kconfig b/net/sched/Kconfig
index 7bac249258e3..59d3e71f8b85 100644
--- a/net/sched/Kconfig
+++ b/net/sched/Kconfig
@@ -1,6 +1,43 @@
 #
 # Traffic control configuration.
 # 
+
+menuconfig NET_SCHED
+        bool "QoS and/or fair queueing"
+        ---help---
+          When the kernel has several packets to send out over a network
+          device, it has to decide which ones to send first, which ones to
+          delay, and which ones to drop. This is the job of the packet
+          scheduler, and several different algorithms for how to do this
+          "fairly" have been proposed.
+
+          If you say N here, you will get the standard packet scheduler, which
+          is a FIFO (first come, first served). If you say Y here, you will be
+          able to choose from among several alternative algorithms which can
+          then be attached to different network devices. This is useful for
+          example if some of your network devices are real time devices that
+          need a certain minimum data flow rate, or if you need to limit the
+          maximum data flow rate for traffic which matches specified criteria.
+          This code is considered to be experimental.
+
+          To administer these schedulers, you'll need the user-level utilities
+          from the package iproute2+tc at <ftp://ftp.tux.org/pub/net/ip-routing/>.
+          That package also contains some documentation; for more, check out
+          <http://snafu.freedom.org/linux2.2/iproute-notes.html>.
+
+          This Quality of Service (QoS) support will enable you to use
+          Differentiated Services (diffserv) and Resource Reservation Protocol
+          (RSVP) on your Linux router if you also say Y to "QoS support",
+          "Packet classifier API" and to some classifiers below. Documentation
+          and software is at <http://diffserv.sourceforge.net/>.
+
+          If you say Y here and to "/proc file system" below, you will be able
+          to read status information about packet schedulers from the file
+          /proc/net/psched.
+
+          The available schedulers are listed in the following questions; you
+          can say Y to as many as you like. If unsure, say N now.
+
 choice
         prompt "Packet scheduler clock source"
         depends on NET_SCHED
diff --git a/net/unix/Kconfig b/net/unix/Kconfig
new file mode 100644
index 000000000000..5a69733bcdad
--- /dev/null
+++ b/net/unix/Kconfig
@@ -0,0 +1,21 @@
+#
+# Unix Domain Sockets
+#
+
+config UNIX
+        tristate "Unix domain sockets"
+        ---help---
+          If you say Y here, you will include support for Unix domain sockets;
+          sockets are the standard Unix mechanism for establishing and
+          accessing network connections.  Many commonly used programs such as
+          the X Window system and syslog use these sockets even if your
+          machine is not connected to any network.  Unless you are working on
+          an embedded system or something similar, you therefore definitely
+          want to say Y here.
+
+          To compile this driver as a module, choose M here: the module will be
+          called unix.  Note that several important services won't work
+          correctly if you say M here and then neglect to load the module.
+
+          Say Y unless you know what you are doing.
+
diff --git a/net/wanrouter/Kconfig b/net/wanrouter/Kconfig
new file mode 100644
index 000000000000..1debe1cb054e
--- /dev/null
+++ b/net/wanrouter/Kconfig
@@ -0,0 +1,29 @@
+#
+# Configuration for WAN router
+#
+
+config WAN_ROUTER
+        tristate "WAN router"
+        depends on EXPERIMENTAL
+        ---help---
+          Wide Area Networks (WANs), such as X.25, frame relay and leased
+          lines, are used to interconnect Local Area Networks (LANs) over vast
+          distances with data transfer rates significantly higher than those
+          achievable with commonly used asynchronous modem connections.
+          Usually, a quite expensive external device called a `WAN router' is
+          needed to connect to a WAN.
+
+          As an alternative, WAN routing can be built into the Linux kernel.
+          With relatively inexpensive WAN interface cards available on the
+          market, a perfectly usable router can be built for less than half
+          the price of an external router.  If you have one of those cards and
+          wish to use your Linux box as a WAN router, say Y here and also to
+          the WAN driver for your card, below.  You will then need the
+          wan-tools package which is available from <ftp://ftp.sangoma.com/>.
+          Read <file:Documentation/networking/wan-router.txt> for more
+          information.
+
+          To compile WAN routing support as a module, choose M here: the
+          module will be called wanrouter.
+
+          If unsure, say N.
diff --git a/net/x25/Kconfig b/net/x25/Kconfig
new file mode 100644
index 000000000000..e6759c9660bb
--- /dev/null
+++ b/net/x25/Kconfig
@@ -0,0 +1,36 @@
+#
+# CCITT X.25 Packet Layer
+#
+
+config X25
+        tristate "CCITT X.25 Packet Layer (EXPERIMENTAL)"
+        depends on EXPERIMENTAL
+        ---help---
+          X.25 is a set of standardized network protocols, similar in scope to
+          frame relay; the one physical line from your box to the X.25 network
+          entry point can carry several logical point-to-point connections
+          (called "virtual circuits") to other computers connected to the X.25
+          network. Governments, banks, and other organizations tend to use it
+          to connect to each other or to form Wide Area Networks (WANs). Many
+          countries have public X.25 networks. X.25 consists of two
+          protocols: the higher level Packet Layer Protocol (PLP) (say Y here
+          if you want that) and the lower level data link layer protocol LAPB
+          (say Y to "LAPB Data Link Driver" below if you want that).
+
+          You can read more about X.25 at <http://www.sangoma.com/x25.htm> and
+          <http://www.cisco.com/univercd/cc/td/doc/product/software/ios11/cbook/cx25.htm>.
+          Information about X.25 for Linux is contained in the files
+          <file:Documentation/networking/x25.txt> and
+          <file:Documentation/networking/x25-iface.txt>.
+
+          One connects to an X.25 network either with a dedicated network card
+          using the X.21 protocol (not yet supported by Linux) or one can do
+          X.25 over a standard telephone line using an ordinary modem (say Y
+          to "X.25 async driver" below) or over Ethernet using an ordinary
+          Ethernet card and the LAPB over Ethernet (say Y to "LAPB Data Link
+          Driver" and "LAPB over Ethernet driver" below).
+
+          To compile this driver as a module, choose M here: the module
+          will be called x25. If unsure, say N.
+
+
diff --git a/net/xfrm/Kconfig b/net/xfrm/Kconfig
index 58ca6a972c48..0c1c04322baf 100644
--- a/net/xfrm/Kconfig
+++ b/net/xfrm/Kconfig
@@ -1,6 +1,10 @@
 #
 # XFRM configuration
 #
+config XFRM
+       bool
+       depends on NET
+
 config XFRM_USER
         tristate "IPsec user configuration interface"
         depends on INET && XFRM
@@ -10,3 +14,14 @@ config XFRM_USER
 
           If unsure, say Y.
 
+config NET_KEY
+        tristate "PF_KEY sockets"
+        select XFRM
+        ---help---
+          PF_KEYv2 socket family, compatible to KAME ones.
+          They are required if you are going to use IPsec tools ported
+          from KAME.
+
+          Say Y unless you know what you are doing.
+
+