cfg80211/mac80211: add mesh join/leave commands

Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.

Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.

We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.

In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 29 insertions, 9 deletions

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 902895dfbd49..788c3989a9e8 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -258,13 +258,9 @@ struct ieee80211_supported_band {
 
 /**
  * struct vif_params - describes virtual interface parameters
- * @mesh_id: mesh ID to use
- * @mesh_id_len: length of the mesh ID
  * @use_4addr: use 4-address frames
  */
 struct vif_params {
-       u8 *mesh_id;
-       int mesh_id_len;
        int use_4addr;
 };
 
@@ -615,6 +611,11 @@ struct bss_parameters {
         int ap_isolate;
 };
 
+/*
+ * struct mesh_config - 802.11s mesh configuration
+ *
+ * These parameters can be changed while the mesh is active.
+ */
 struct mesh_config {
         /* Timeouts in ms */
         /* Mesh plink management parameters */
@@ -638,6 +639,18 @@ struct mesh_config {
 };
 
 /**
+ * struct mesh_setup - 802.11s mesh setup configuration
+ * @mesh_id: the mesh ID
+ * @mesh_id_len: length of the mesh ID, at least 1 and at most 32 bytes
+ *
+ * These parameters are fixed when the mesh is created.
+ */
+struct mesh_setup {
+        const u8 *mesh_id;
+        u8 mesh_id_len;
+};
+
+/**
  * struct ieee80211_txq_params - TX queue parameters
  * @queue: TX queue identifier (NL80211_TXQ_Q_*)
  * @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled
@@ -1078,7 +1091,7 @@ struct cfg80211_pmksa {
  *
  * @get_mesh_params: Put the current mesh parameters into *params
  *
- * @set_mesh_params: Set mesh parameters.
+ * @update_mesh_params: Update mesh parameters on a running mesh.
  *      The mask is a bitfield which tells us which parameters to
  *      set, and which to leave alone.
  *
@@ -1229,9 +1242,14 @@ struct cfg80211_ops {
         int     (*get_mesh_params)(struct wiphy *wiphy,
                                 struct net_device *dev,
                                 struct mesh_config *conf);
-        int     (*set_mesh_params)(struct wiphy *wiphy,
-                                struct net_device *dev,
-                                const struct mesh_config *nconf, u32 mask);
+        int     (*update_mesh_params)(struct wiphy *wiphy,
+                                      struct net_device *dev, u32 mask,
+                                      const struct mesh_config *nconf);
+        int     (*join_mesh)(struct wiphy *wiphy, struct net_device *dev,
+                             const struct mesh_config *conf,
+                             const struct mesh_setup *setup);
+        int     (*leave_mesh)(struct wiphy *wiphy, struct net_device *dev);
+
         int     (*change_bss)(struct wiphy *wiphy, struct net_device *dev,
                               struct bss_parameters *params);
 
@@ -1647,6 +1665,8 @@ struct cfg80211_cached_keys;
  * @bssid: (private) Used by the internal configuration code
  * @ssid: (private) Used by the internal configuration code
  * @ssid_len: (private) Used by the internal configuration code
+ * @mesh_id_len: (private) Used by the internal configuration code
+ * @mesh_id_up_len: (private) Used by the internal configuration code
  * @wext: (private) Used by the internal wireless extensions compat code
  * @use_4addr: indicates 4addr mode is used on this interface, must be
  *      set by driver (if supported) on add_interface BEFORE registering the
@@ -1676,7 +1696,7 @@ struct wireless_dev {
 
         /* currently used for IBSS and SME - might be rearranged later */
         u8 ssid[IEEE80211_MAX_SSID_LEN];
-        u8 ssid_len;
+        u8 ssid_len, mesh_id_len, mesh_id_up_len;
         enum {
                 CFG80211_SME_IDLE,
                 CFG80211_SME_CONNECTING,