ssb: Implement the remaining rev.8 SPROM vars needed for LP-PHY

Also add a "SPEX32" macro for extracting 32-bit SPROM variables.

Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 37 insertions, 7 deletions

diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
index 5ae8fa22d331..17ffc1f84d76 100644
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -27,24 +27,54 @@ struct ssb_sprom {
         u8 et1mdcport;          /* MDIO for enet1 */
         u8 board_rev;           /* Board revision number from SPROM. */
         u8 country_code;        /* Country Code */
-        u8 ant_available_a;     /* A-PHY antenna available bits (up to 4) */
-        u8 ant_available_bg;    /* B/G-PHY antenna available bits (up to 4) */
+        u8 ant_available_a;     /* 2GHz antenna available bits (up to 4) */
+        u8 ant_available_bg;    /* 5GHz antenna available bits (up to 4) */
         u16 pa0b0;
         u16 pa0b1;
         u16 pa0b2;
         u16 pa1b0;
         u16 pa1b1;
         u16 pa1b2;
+        u16 pa1lob0;
+        u16 pa1lob1;
+        u16 pa1lob2;
+        u16 pa1hib0;
+        u16 pa1hib1;
+        u16 pa1hib2;
         u8 gpio0;               /* GPIO pin 0 */
         u8 gpio1;               /* GPIO pin 1 */
         u8 gpio2;               /* GPIO pin 2 */
         u8 gpio3;               /* GPIO pin 3 */
-        u16 maxpwr_a;           /* A-PHY Amplifier Max Power (in dBm Q5.2) */
-        u16 maxpwr_bg;          /* B/G-PHY Amplifier Max Power (in dBm Q5.2) */
+        u16 maxpwr_bg;          /* 2.4GHz Amplifier Max Power (in dBm Q5.2) */
+        u16 maxpwr_al;          /* 5.2GHz Amplifier Max Power (in dBm Q5.2) */
+        u16 maxpwr_a;           /* 5.3GHz Amplifier Max Power (in dBm Q5.2) */
+        u16 maxpwr_ah;          /* 5.8GHz Amplifier Max Power (in dBm Q5.2) */
         u8 itssi_a;             /* Idle TSSI Target for A-PHY */
         u8 itssi_bg;            /* Idle TSSI Target for B/G-PHY */
-        u16 boardflags_lo;      /* Boardflags (low 16 bits) */
-        u16 boardflags_hi;      /* Boardflags (high 16 bits) */
+        u8 tri2g;               /* 2.4GHz TX isolation */
+        u8 tri5gl;              /* 5.2GHz TX isolation */
+        u8 tri5g;               /* 5.3GHz TX isolation */
+        u8 tri5gh;              /* 5.8GHz TX isolation */
+        u8 rxpo2g;              /* 2GHz RX power offset */
+        u8 rxpo5g;              /* 5GHz RX power offset */
+        u8 rssisav2g;           /* 2GHz RSSI params */
+        u8 rssismc2g;
+        u8 rssismf2g;
+        u8 bxa2g;               /* 2GHz BX arch */
+        u8 rssisav5g;           /* 5GHz RSSI params */
+        u8 rssismc5g;
+        u8 rssismf5g;
+        u8 bxa5g;               /* 5GHz BX arch */
+        u16 cck2gpo;            /* CCK power offset */
+        u32 ofdm2gpo;           /* 2.4GHz OFDM power offset */
+        u32 ofdm5glpo;          /* 5.2GHz OFDM power offset */
+        u32 ofdm5gpo;           /* 5.3GHz OFDM power offset */
+        u32 ofdm5ghpo;          /* 5.8GHz OFDM power offset */
+        u16 boardflags_lo;      /* Board flags (bits 0-15) */
+        u16 boardflags_hi;      /* Board flags (bits 16-31) */
+        u16 boardflags2_lo;     /* Board flags (bits 32-47) */
+        u16 boardflags2_hi;     /* Board flags (bits 48-63) */
+        /* TODO store board flags in a single u64 */
 
         /* Antenna gain values for up to 4 antennas
          * on each band. Values in dBm/4 (Q5.2). Negative gain means the
@@ -58,7 +88,7 @@ struct ssb_sprom {
                 } ghz5;         /* 5GHz band */
         } antenna_gain;
 
-        /* TODO - add any parameters needed from rev 2, 3, or 4 SPROMs */
+        /* TODO - add any parameters needed from rev 2, 3, 4, 5 or 8 SPROMs */
 };
 
 /* Information about the PCB the circuitry is soldered on. */