mmc: enable/disable functions for SDIO

Like many other buses, the devices (functions) on the SDIO bus
must be enabled before they can be used. Add functions that allow
drivers to do so.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

1 files changed, 92 insertions, 0 deletions

diff --git a/include/linux/mmc/sdio.h b/include/linux/mmc/sdio.h
index e5f06de7d527..56239f4aab04 100644
--- a/include/linux/mmc/sdio.h
+++ b/include/linux/mmc/sdio.h
@@ -49,5 +49,97 @@
 #define R5_STATUS(x)            (x & 0xCB00)
 #define R5_IO_CURRENT_STATE(x)  ((x & 0x3000) >> 12) /* s, b */
 
+/*
+ * Card Common Control Registers (CCCR)
+ */
+
+#define SDIO_CCCR_CCCR          0x00
+
+#define  SDIO_CCCR_REV_1_00     0       /* CCCR/FBR Version 1.00 */
+#define  SDIO_CCCR_REV_1_10     1       /* CCCR/FBR Version 1.10 */
+#define  SDIO_CCCR_REV_1_20     2       /* CCCR/FBR Version 1.20 */
+
+#define  SDIO_SDIO_REV_1_00     0       /* SDIO Spec Version 1.00 */
+#define  SDIO_SDIO_REV_1_10     1       /* SDIO Spec Version 1.10 */
+#define  SDIO_SDIO_REV_1_20     2       /* SDIO Spec Version 1.20 */
+#define  SDIO_SDIO_REV_2_00     3       /* SDIO Spec Version 2.00 */
+
+#define SDIO_CCCR_SD            0x01
+
+#define  SDIO_SD_REV_1_01       0       /* SD Physical Spec Version 1.01 */
+#define  SDIO_SD_REV_1_10       1       /* SD Physical Spec Version 1.10 */
+#define  SDIO_SD_REV_2_00       2       /* SD Physical Spec Version 2.00 */
+
+#define SDIO_CCCR_IOEx          0x02
+#define SDIO_CCCR_IORx          0x03
+
+#define SDIO_CCCR_IENx          0x04    /* Function/Master Interrupt Enable */
+#define SDIO_CCCR_INTx          0x05    /* Function Interrupt Pending */
+
+#define SDIO_CCCR_ABORT         0x06    /* function abort/card reset */
+
+#define SDIO_CCCR_IF            0x07    /* bus interface controls */
+
+#define  SDIO_BUS_WIDTH_1BIT    0x00
+#define  SDIO_BUS_WIDTH_4BIT    0x02
+
+#define  SDIO_BUS_CD_DISABLE     0x80   /* disable pull-up on DAT3 (pin 1) */
+
+#define SDIO_CCCR_CAPS          0x08
+
+#define  SDIO_CCCR_CAP_SDC      0x01    /* can do CMD52 while data transfer */
+#define  SDIO_CCCR_CAP_SMB      0x02    /* can do multi-block xfers (CMD53) */
+#define  SDIO_CCCR_CAP_SRW      0x04    /* supports read-wait protocol */
+#define  SDIO_CCCR_CAP_SBS      0x08    /* supports suspend/resume */
+#define  SDIO_CCCR_CAP_S4MI     0x10    /* interrupt during 4-bit CMD53 */
+#define  SDIO_CCCR_CAP_E4MI     0x20    /* enable ints during 4-bit CMD53 */
+#define  SDIO_CCCR_CAP_LSC      0x40    /* low speed card */
+#define  SDIO_CCCR_CAP_4BLS     0x80    /* 4 bit low speed card */
+
+#define SDIO_CCCR_CIS           0x09    /* common CIS pointer (3 bytes) */
+
+/* Following 4 regs are valid only if SBS is set */
+#define SDIO_CCCR_SUSPEND       0x0c
+#define SDIO_CCCR_SELx          0x0d
+#define SDIO_CCCR_EXECx         0x0e
+#define SDIO_CCCR_READYx        0x0f
+
+#define SDIO_CCCR_BLKSIZE       0x10
+
+#define SDIO_CCCR_POWER         0x12
+
+#define  SDIO_POWER_SMPC        0x01    /* Supports Master Power Control */
+#define  SDIO_POWER_EMPC        0x02    /* Enable Master Power Control */
+
+#define SDIO_CCCR_SPEED         0x13
+
+#define  SDIO_SPEED_SHS         0x01    /* Supports High-Speed mode */
+#define  SDIO_SPEED_EHS         0x02    /* Enable High-Speed mode */
+
+/*
+ * Function Basic Registers (FBR)
+ */
+
+#define SDIO_FBR_STD_IF         0x00
+
+#define  SDIO_FBR_SUPPORTS_CSA  0x40    /* supports Code Storage Area */
+#define  SDIO_FBR_ENABLE_CSA    0x80    /* enable Code Storage Area */
+
+#define SDIO_FBR_STD_IF_EXT     0x01
+
+#define SDIO_FBR_POWER          0x02
+
+#define  SDIO_FBR_POWER_SPS     0x01    /* Supports Power Selection */
+#define  SDIO_FBR_POWER_EPS     0x02    /* Enable (low) Power Selection */
+
+#define SDIO_FBR_CIS            0x09    /* CIS pointer (3 bytes) */
+
+
+#define SDIO_FBR_CSA            0x0C    /* CSA pointer (3 bytes) */
+
+#define SDIO_FBR_CSA_DATA       0x0F
+
+#define SDIO_FBR_BLKSIZE        0x10    /* block size (2 bytes) */
+
 #endif