Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 115 insertions, 0 deletions

diff --git a/include/linux/com20020.h b/include/linux/com20020.h
new file mode 100644
index 000000000000..ac6d9a43e085
--- /dev/null
+++ b/include/linux/com20020.h
@@ -0,0 +1,115 @@
+/*
+ * Linux ARCnet driver - COM20020 chipset support - function declarations
+ * 
+ * Written 1997 by David Woodhouse.
+ * Written 1994-1999 by Avery Pennarun.
+ * Derived from skeleton.c by Donald Becker.
+ *
+ * Special thanks to Contemporary Controls, Inc. (www.ccontrols.com)
+ *  for sponsoring the further development of this driver.
+ *
+ * **********************
+ *
+ * The original copyright of skeleton.c was as follows:
+ *
+ * skeleton.c Written 1993 by Donald Becker.
+ * Copyright 1993 United States Government as represented by the
+ * Director, National Security Agency.  This software may only be used
+ * and distributed according to the terms of the GNU General Public License as
+ * modified by SRC, incorporated herein by reference.
+ *
+ * **********************
+ *
+ * For more details, see drivers/net/arcnet.c
+ *
+ * **********************
+ */
+#ifndef __COM20020_H
+#define __COM20020_H
+
+int com20020_check(struct net_device *dev);
+int com20020_found(struct net_device *dev, int shared);
+
+/* The number of low I/O ports used by the card. */
+#define ARCNET_TOTAL_SIZE 8
+
+/* various register addresses */
+#ifdef CONFIG_SA1100_CT6001
+#define BUS_ALIGN  2  /* 8 bit device on a 16 bit bus - needs padding */
+#else
+#define BUS_ALIGN  1
+#endif
+
+
+#define _INTMASK  (ioaddr+BUS_ALIGN*0)  /* writable */
+#define _STATUS   (ioaddr+BUS_ALIGN*0)  /* readable */
+#define _COMMAND  (ioaddr+BUS_ALIGN*1)  /* standard arcnet commands */
+#define _DIAGSTAT (ioaddr+BUS_ALIGN*1)  /* diagnostic status register */
+#define _ADDR_HI  (ioaddr+BUS_ALIGN*2)  /* control registers for IO-mapped memory */
+#define _ADDR_LO  (ioaddr+BUS_ALIGN*3)
+#define _MEMDATA  (ioaddr+BUS_ALIGN*4)  /* data port for IO-mapped memory */
+#define _SUBADR   (ioaddr+BUS_ALIGN*5)  /* the extended port _XREG refers to */
+#define _CONFIG   (ioaddr+BUS_ALIGN*6)  /* configuration register */
+#define _XREG     (ioaddr+BUS_ALIGN*7)  /* extra registers (indexed by _CONFIG
+                                        or _SUBADR) */
+
+/* in the ADDR_HI register */
+#define RDDATAflag      0x80    /* next access is a read (not a write) */
+
+/* in the DIAGSTAT register */
+#define NEWNXTIDflag    0x02    /* ID to which token is passed has changed */
+
+/* in the CONFIG register */
+#define RESETcfg        0x80    /* put card in reset state */
+#define TXENcfg         0x20    /* enable TX */
+
+/* in SETUP register */
+#define PROMISCset      0x10    /* enable RCV_ALL */
+#define P1MODE          0x80    /* enable P1-MODE for Backplane */
+#define SLOWARB         0x01    /* enable Slow Arbitration for >=5Mbps */
+
+/* COM2002x */
+#define SUB_TENTATIVE   0       /* tentative node ID */
+#define SUB_NODE        1       /* node ID */
+#define SUB_SETUP1      2       /* various options */
+#define SUB_TEST        3       /* test/diag register */
+
+/* COM20022 only */
+#define SUB_SETUP2      4       /* sundry options */
+#define SUB_BUSCTL      5       /* bus control options */
+#define SUB_DMACOUNT    6       /* DMA count options */
+
+#define SET_SUBADR(x) do { \
+        if ((x) < 4) \
+        { \
+                lp->config = (lp->config & ~0x03) | (x); \
+                SETCONF; \
+        } \
+        else \
+        { \
+                outb(x, _SUBADR); \
+        } \
+} while (0)
+
+#undef ARCRESET
+#undef ASTATUS
+#undef ACOMMAND
+#undef AINTMASK
+
+#define ARCRESET { outb(lp->config | 0x80, _CONFIG); \
+                    udelay(5);                        \
+                    outb(lp->config , _CONFIG);       \
+                  }
+#define ARCRESET0 { outb(0x18 | 0x80, _CONFIG);   \
+                    udelay(5);                       \
+                    outb(0x18 , _CONFIG);            \
+                  }
+
+#define ASTATUS()       inb(_STATUS)
+#define ADIAGSTATUS()   inb(_DIAGSTAT)
+#define ACOMMAND(cmd)   outb((cmd),_COMMAND)
+#define AINTMASK(msk)   outb((msk),_INTMASK)
+
+#define SETCONF         outb(lp->config, _CONFIG)
+
+#endif /* __COM20020_H */