Blackfin arch: revise anomaly handling by basing things on the compiler not the kconfig defines

revise anomaly handling by basing things on the compiler not the kconfig defines,
so the header is stable and usable outside of the kernel. This also allows us to
move some code from preprocessing to compiling (gcc culls dead code)
which should help with code quality (readability, catch minor bugs, etc...).

Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

1 files changed, 235 insertions, 202 deletions

diff --git a/include/asm-blackfin/mach-bf533/anomaly.h b/include/asm-blackfin/mach-bf533/anomaly.h
index 2a63ffc250a1..caea0b0f8326 100644
--- a/include/asm-blackfin/mach-bf533/anomaly.h
+++ b/include/asm-blackfin/mach-bf533/anomaly.h
@@ -7,219 +7,252 @@
  */
 
 /* This file shoule be up to date with:
- *  - Revision U, May 17, 2006; ADSP-BF533 Blackfin Processor Anomaly List
- *  - Revision Y, May 17, 2006; ADSP-BF532 Blackfin Processor Anomaly List
- *  - Revision T, May 17, 2006; ADSP-BF531 Blackfin Processor Anomaly List
+ *  - Revision X,  March 23, 2007; ADSP-BF533 Blackfin Processor Anomaly List
+ *  - Revision AB, March 23, 2007; ADSP-BF532 Blackfin Processor Anomaly List
+ *  - Revision W,  March 23, 2007; ADSP-BF531 Blackfin Processor Anomaly List
  */
 
 #ifndef _MACH_ANOMALY_H_
 #define _MACH_ANOMALY_H_
 
 /* We do not support 0.1 or 0.2 silicon - sorry */
-#if (defined(CONFIG_BF_REV_0_1) || defined(CONFIG_BF_REV_0_2))
-#error Kernel will not work on BF533 Version 0.1 or 0.2
+#if __SILICON_REVISION__ < 3
+# error Kernel will not work on BF533 silicon version 0.0, 0.1, or 0.2
 #endif
 
-/* Issues that are common to 0.5, 0.4, and 0.3 silicon */
-#if (defined(CONFIG_BF_REV_0_5) || defined(CONFIG_BF_REV_0_4) \
-                || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000074 /* A multi issue instruction with dsp32shiftimm in
-                          * slot1 and store of a P register in slot 2 is not
-                          * supported */
-#define ANOMALY_05000105 /* Watchpoint Status Register (WPSTAT) bits are set on
-                          * every corresponding match */
-#define ANOMALY_05000119 /* DMA_RUN bit is not valid after a Peripheral Receive
-                          * Channel DMA stops */
-#define ANOMALY_05000122 /* Rx.H can not be used to access 16-bit System MMR
-                          * registers. */
-#define ANOMALY_05000166 /* PPI Data Lengths Between 8 and 16 do not zero out
-                          * upper bits*/
-#define ANOMALY_05000167 /* Turning Serial Ports on With External Frame Syncs */
-#define ANOMALY_05000180 /* PPI_DELAY not functional in PPI modes with 0 frame
-                          * syncs */
-#define ANOMALY_05000208 /* VSTAT status bit in PLL_STAT register is not
-                          * functional */
-#define ANOMALY_05000219 /* NMI event at boot time results in unpredictable
-                          * state */
-#define ANOMALY_05000229 /* SPI Slave Boot Mode modifies registers */
-#define ANOMALY_05000272 /* Certain data cache write through modes fail for
-                          * VDDint <=0.9V */
-#define ANOMALY_05000273 /* Writes to Synchronous SDRAM memory may be lost */
-#define ANOMALY_05000277 /* Writes to a flag data register one SCLK cycle after
-                          * an edge is detected may clear interrupt */
-#define ANOMALY_05000278 /* Disabling Peripherals with DMA running may cause
-                          * DMA system instability */
-#define ANOMALY_05000281 /* False Hardware Error Exception when ISR context is
-                          * not restored */
-#define ANOMALY_05000282 /* Memory DMA corruption with 32-bit data and traffic
-                          * control */
-#define ANOMALY_05000283 /* A system MMR write is stalled indefinitely when
-                          * killed in a particular stage*/
-#define ANOMALY_05000311 /* Erroneous flag pin operations under specific
-                          * sequences */
-#define ANOMALY_05000312 /* Errors when SSYNC, CSYNC, or loads to LT, LB and LC
-                          * registers are interrupted */
-#define ANOMALY_05000313 /* PPI Is Level-Sensitive on First Transfer  */
-#define ANOMALY_05000315 /* Killed System MMR Write Completes Erroneously On
-                          *  Next System MMR Access */
-#define ANOMALY_05000319 /* Internal Voltage Regulator Values of 1.05V, 1.10V
-                          *  and 1.15V Not Allowed for LQFP Packages */
-#endif /* Issues that are common to 0.5, 0.4, and 0.3 silicon */
+#if defined(__ADSPBF531__)
+# define ANOMALY_BF531 1
+#else
+# define ANOMALY_BF531 0
+#endif
+#if defined(__ADSPBF532__)
+# define ANOMALY_BF532 1
+#else
+# define ANOMALY_BF532 0
+#endif
+#if defined(__ADSPBF533__)
+# define ANOMALY_BF533 1
+#else
+# define ANOMALY_BF533 0
+#endif
 
-/* These issues only occur on 0.3 or 0.4 BF533 */
-#if (defined(CONFIG_BF_REV_0_4) || defined(CONFIG_BF_REV_0_3))
-#define ANOMALY_05000099 /* UART Line Status Register (UART_LSR) bits are not
-                          * updated at the same time. */
-#define ANOMALY_05000158 /* Boot fails when data cache enabled: Data from a Data
-                          * Cache Fill can be corrupted after or during
-                          * Instruction DMA if certain core stalls exist */
-#define ANOMALY_05000179 /* PPI_COUNT cannot be programmed to 0 in General
-                          * Purpose TX or RX modes */
-#define ANOMALY_05000198 /* Failing SYSTEM MMR accesses when stalled by
-                          * preceding memory read */
-#define ANOMALY_05000200 /* SPORT TFS and DT are incorrectly driven during
-                          * inactive channels in certain conditions */
-#define ANOMALY_05000202 /* Possible infinite stall with specific dual dag
-                          * situation */
-#define ANOMALY_05000215 /* UART TX Interrupt masked erroneously */
-#define ANOMALY_05000225 /* Incorrect pulse-width of UART start-bit */
-#define ANOMALY_05000227 /* Scratchpad memory bank reads may return incorrect
-                          * data*/
-#define ANOMALY_05000230 /* UART Receiver is less robust against Baudrate
-                          * Differences in certain Conditions */
-#define ANOMALY_05000231 /* UART STB bit incorrectly affects receiver setting */
-#define ANOMALY_05000242 /* DF bit in PLL_CTL register does not respond to
-                          * hardware reset */
-#define ANOMALY_05000244 /* With instruction cache enabled, a CSYNC or SSYNC or
-                          * IDLE around a Change of Control causes
-                          * unpredictable results */
-#define ANOMALY_05000245 /* Spurious Hardware Error from an access in the
-                          * shadow of a conditional branch */
-#define ANOMALY_05000246 /* Data CPLB's should prevent spurious hardware
-                          * errors */
-#define ANOMALY_05000253 /* Maximum external clock speed for Timers */
-#define ANOMALY_05000255 /* Entering Hibernate Mode with RTC Seconds event
-                          * interrupt not functional */
-#define ANOMALY_05000257 /* An interrupt or exception during short Hardware
-                          * loops may cause the instruction fetch unit to
-                          * malfunction */
-#define ANOMALY_05000258 /* Instruction Cache is corrupted when bit 9 and 12 of
-                          * the ICPLB Data registers differ */
-#define ANOMALY_05000260 /* ICPLB_STATUS MMR register may be corrupted */
-#define ANOMALY_05000261 /* DCPLB_FAULT_ADDR MMR register may be corrupted */
-#define ANOMALY_05000262 /* Stores to data cache may be lost */
-#define ANOMALY_05000263 /* Hardware loop corrupted when taking an ICPLB exception */
-#define ANOMALY_05000264 /* A Sync instruction (CSYNC, SSYNC) or an IDLE
-                          * instruction will cause an infinite stall in the
-                          * second to last instruction in a hardware loop */
-#define ANOMALY_05000265 /* Sensitivity to noise with slow input edge rates on
-                          * SPORT external receive and transmit clocks. */
-#define ANOMALY_05000269 /* High I/O activity causes the output voltage of the
-                          * internal voltage regulator (VDDint) to increase. */
-#define ANOMALY_05000270 /* High I/O activity causes the output voltage of the
-                          * internal voltage regulator (VDDint) to decrease */
-#endif /* issues only occur on 0.3 or 0.4 BF533 */
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot 2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* UART Line Status Register (UART_LSR) Bits Are Not Updated at the Same Time */
+#define ANOMALY_05000099 (__SILICON_REVISION__ < 5)
+/* Watchpoint Status Register (WPSTAT) Bits Are Set on Every Corresponding Match */
+#define ANOMALY_05000105 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Instruction DMA Can Cause Data Cache Fills to Fail (Boot Implications) */
+#define ANOMALY_05000158 (__SILICON_REVISION__ < 5)
+/* PPI Data Lengths Between 8 and 16 Do Not Zero Out Upper Bits */
+#define ANOMALY_05000166 (1)
+/* Turning Serial Ports on with External Frame Syncs */
+#define ANOMALY_05000167 (1)
+/* PPI_COUNT Cannot Be Programmed to 0 in General Purpose TX or RX Modes */
+#define ANOMALY_05000179 (__SILICON_REVISION__ < 5)
+/* PPI_DELAY Not Functional in PPI Modes with 0 Frame Syncs */
+#define ANOMALY_05000180 (1)
+/* Timer Pin Limitations for PPI TX Modes with External Frame Syncs */
+#define ANOMALY_05000183 (__SILICON_REVISION__ < 4)
+/* False Protection Exceptions */
+#define ANOMALY_05000189 (__SILICON_REVISION__ < 4)
+/* False I/O Pin Interrupts on Edge-Sensitive Inputs When Polarity Setting Is Changed */
+#define ANOMALY_05000193 (__SILICON_REVISION__ < 4)
+/* Restarting SPORT in Specific Modes May Cause Data Corruption */
+#define ANOMALY_05000194 (__SILICON_REVISION__ < 4)
+/* Failing MMR Accesses When Stalled by Preceding Memory Read */
+#define ANOMALY_05000198 (__SILICON_REVISION__ < 5)
+/* Current DMA Address Shows Wrong Value During Carry Fix */
+#define ANOMALY_05000199 (__SILICON_REVISION__ < 4)
+/* SPORT TFS and DT Are Incorrectly Driven During Inactive Channels in Certain Conditions */
+#define ANOMALY_05000200 (__SILICON_REVISION__ < 5)
+/* Receive Frame Sync Not Ignored During Active Frames in SPORT Multi-Channel Mode */
+#define ANOMALY_05000201 (__SILICON_REVISION__ < 4)
+/* Possible Infinite Stall with Specific Dual-DAG Situation */
+#define ANOMALY_05000202 (__SILICON_REVISION__ < 5)
+/* Specific Sequence That Can Cause DMA Error or DMA Stopping */
+#define ANOMALY_05000203 (__SILICON_REVISION__ < 4)
+/* Incorrect data read with write-through cache and allocate cache lines on reads only mode */
+#define ANOMALY_05000204 (__SILICON_REVISION__ < 4 && ANOMALY_BF533)
+/* Recovery from "Brown-Out" Condition */
+#define ANOMALY_05000207 (__SILICON_REVISION__ < 4)
+/* VSTAT Status Bit in PLL_STAT Register Is Not Functional */
+#define ANOMALY_05000208 (1)
+/* Speed Path in Computational Unit Affects Certain Instructions */
+#define ANOMALY_05000209 (__SILICON_REVISION__ < 4)
+/* UART TX Interrupt Masked Erroneously */
+#define ANOMALY_05000215 (__SILICON_REVISION__ < 5)
+/* NMI Event at Boot Time Results in Unpredictable State */
+#define ANOMALY_05000219 (1)
+/* Incorrect Pulse-Width of UART Start Bit */
+#define ANOMALY_05000225 (__SILICON_REVISION__ < 5)
+/* Scratchpad Memory Bank Reads May Return Incorrect Data */
+#define ANOMALY_05000227 (__SILICON_REVISION__ < 5)
+/* SPI Slave Boot Mode Modifies Registers from Reset Value */
+#define ANOMALY_05000229 (1)
+/* UART Receiver is Less Robust Against Baudrate Differences in Certain Conditions */
+#define ANOMALY_05000230 (__SILICON_REVISION__ < 5)
+/* UART STB Bit Incorrectly Affects Receiver Setting */
+#define ANOMALY_05000231 (__SILICON_REVISION__ < 5)
+/* PPI_FS3 Is Not Driven in 2 or 3 Internal Frame Sync Transmit Modes */
+#define ANOMALY_05000233 (__SILICON_REVISION__ < 4)
+/* Incorrect Revision Number in DSPID Register */
+#define ANOMALY_05000234 (__SILICON_REVISION__ == 4)
+/* DF Bit in PLL_CTL Register Does Not Respond to Hardware Reset */
+#define ANOMALY_05000242 (__SILICON_REVISION__ < 4)
+/* If I-Cache Is On, CSYNC/SSYNC/IDLE Around Change of Control Causes Failures */
+#define ANOMALY_05000244 (__SILICON_REVISION__ < 5)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Data CPLBs Should Prevent Spurious Hardware Errors */
+#define ANOMALY_05000246 (__SILICON_REVISION__ < 5)
+/* Incorrect Bit Shift of Data Word in Multichannel (TDM) Mode in Certain Conditions */
+#define ANOMALY_05000250 (__SILICON_REVISION__ == 4)
+/* Maximum External Clock Speed for Timers */
+#define ANOMALY_05000253 (__SILICON_REVISION__ < 5)
+/* Incorrect Timer Pulse Width in Single-Shot PWM_OUT Mode with External Clock */
+#define ANOMALY_05000254 (__SILICON_REVISION__ > 4)
+/* Entering Hibernate State with RTC Seconds Interrupt Not Functional */
+#define ANOMALY_05000255 (__SILICON_REVISION__ < 5)
+/* Interrupt/Exception During Short Hardware Loop May Cause Bad Instruction Fetches */
+#define ANOMALY_05000257 (__SILICON_REVISION__ < 5)
+/* Instruction Cache Is Corrupted When Bits 9 and 12 of the ICPLB Data Registers Differ */
+#define ANOMALY_05000258 (__SILICON_REVISION__ < 5)
+/* ICPLB_STATUS MMR Register May Be Corrupted */
+#define ANOMALY_05000260 (__SILICON_REVISION__ < 5)
+/* DCPLB_FAULT_ADDR MMR Register May Be Corrupted */
+#define ANOMALY_05000261 (__SILICON_REVISION__ < 5)
+/* Stores To Data Cache May Be Lost */
+#define ANOMALY_05000262 (__SILICON_REVISION__ < 5)
+/* Hardware Loop Corrupted When Taking an ICPLB Exception */
+#define ANOMALY_05000263 (__SILICON_REVISION__ < 5)
+/* CSYNC/SSYNC/IDLE Causes Infinite Stall in Penultimate Instruction in Hardware Loop */
+#define ANOMALY_05000264 (__SILICON_REVISION__ < 5)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Increase */
+#define ANOMALY_05000269 (__SILICON_REVISION__ < 5)
+/* High I/O Activity Causes Output Voltage of Internal Voltage Regulator (Vddint) to Decrease */
+#define ANOMALY_05000270 (__SILICON_REVISION__ < 5)
+/* Spontaneous Reset of Internal Voltage Regulator */
+#define ANOMALY_05000271 (__SILICON_REVISION__ < 4)
+/* Certain Data Cache Writethrough Modes Fail for Vddint <= 0.9V */
+#define ANOMALY_05000272 (1)
+/* Writes to Synchronous SDRAM Memory May Be Lost */
+#define ANOMALY_05000273 (1)
+/* Timing Requirements Change for External Frame Sync PPI Modes with Non-Zero PPI_DELAY */
+#define ANOMALY_05000276 (1)
+/* Writes to an I/O Data Register One SCLK Cycle after an Edge Is Detected May Clear Interrupt */
+#define ANOMALY_05000277 (1)
+/* Disabling Peripherals with DMA Running May Cause DMA System Instability */
+#define ANOMALY_05000278 (1)
+/* False Hardware Error Exception When ISR Context Is Not Restored */
+#define ANOMALY_05000281 (1)
+/* Memory DMA Corruption with 32-Bit Data and Traffic Control */
+#define ANOMALY_05000282 (1)
+/* System MMR Write Is Stalled Indefinitely When Killed in a Particular Stage */
+#define ANOMALY_05000283 (1)
+/* SPORTs May Receive Bad Data If FIFOs Fill Up */
+#define ANOMALY_05000288 (1)
+/* Memory-To-Memory DMA Source/Destination Descriptors Must Be in Same Memory Space */
+#define ANOMALY_05000301 (1)
+/* SSYNCs After Writes To DMA MMR Registers May Not Be Handled Correctly */
+#define ANOMALY_05000302 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional Hysteresis on SPORT Input Pins (Not Available On Older Silicon) */
+#define ANOMALY_05000305 (__SILICON_REVISION__ < 5)
+/* New Feature: Additional PPI Frame Sync Sampling Options (Not Available On Older Silicon) */
+#define ANOMALY_05000306 (__SILICON_REVISION__ < 5)
+/* False Hardware Errors Caused by Fetches at the Boundary of Reserved Memory */
+#define ANOMALY_05000310 (1)
+/* Erroneous Flag (GPIO) Pin Operations under Specific Sequences */
+#define ANOMALY_05000311 (1)
+/* Errors When SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* PPI Is Level-Sensitive on First Transfer */
+#define ANOMALY_05000313 (1)
+/* Killed System MMR Write Completes Erroneously On Next System MMR Access */
+#define ANOMALY_05000315 (1)
+/* Internal Voltage Regulator Values of 1.05V, 1.10V and 1.15V Not Allowed for LQFP Packages */
+#define ANOMALY_05000319 (ANOMALY_BF531 || ANOMALY_BF532)
 
-/* These issues are only on 0.4 silicon */
-#if (defined(CONFIG_BF_REV_0_4))
-#define ANOMALY_05000234 /* Incorrect Revision Number in DSPID Register */
-#define ANOMALY_05000250 /* Incorrect Bit-Shift of Data Word in Multichannel
-                          * (TDM) */
-#endif /* issues are only on 0.4 silicon */
+/* These anomalies have been "phased" out of analog.com anomaly sheets and are
+ * here to show running on older silicon just isn't feasible.
+ */
 
-/* These issues are only on 0.3 silicon */
-#if defined(CONFIG_BF_REV_0_3)
-#define ANOMALY_05000183 /* Timer Pin limitations for PPI TX Modes with
-                          * External Frame Syncs */
-#define ANOMALY_05000189 /* False Protection Exceptions caused by Speculative
-                          * Instruction or Data Fetches, or by Fetches at the
-                          * boundary of reserved memory space */
-#define ANOMALY_05000193 /* False Flag Pin Interrupts on Edge Sensitive Inputs
-                          * when polarity setting is changed */
-#define ANOMALY_05000194 /* Sport Restarting in specific modes may cause data
-                          * corruption */
-#define ANOMALY_05000199 /* DMA current address shows wrong value during carry
-                          * fix */
-#define ANOMALY_05000201 /* Receive frame sync not ignored during active
-                          * frames in sport MCM */
-#define ANOMALY_05000203 /* Specific sequence that can cause DMA error or DMA
-                          * stopping */
-#if defined(CONFIG_BF533)
-#define ANOMALY_05000204 /* Incorrect data read with write-through cache and
-                          * allocate cache lines on reads only mode */
-#endif /* CONFIG_BF533 */
-#define ANOMALY_05000207 /* Recovery from "brown-out" condition */
-#define ANOMALY_05000209 /* Speed-Path in computational unit affects certain
-                          * instructions */
-#define ANOMALY_05000233 /* PPI_FS3 is not driven in 2 or 3 internal Frame
-                          * Sync Transmit Mode */
-#define ANOMALY_05000271 /* Spontaneous reset of Internal Voltage Regulator */
-#endif /* only on 0.3 silicon */
+/* Watchpoints (Hardware Breakpoints) are not supported */
+#define ANOMALY_05000067 (__SILICON_REVISION__ < 3)
+/* Reserved bits in SYSCFG register not set at power on */
+#define ANOMALY_05000109 (__SILICON_REVISION__ < 3)
+/* Trace Buffers may record discontinuities into emulation mode and/or exception, NMI, reset handlers */
+#define ANOMALY_05000116 (__SILICON_REVISION__ < 3)
+/* DTEST_COMMAND initiated memory access may be incorrect if data cache or DMA is active */
+#define ANOMALY_05000123 (__SILICON_REVISION__ < 3)
+/* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1, or 1:1 */
+#define ANOMALY_05000124 (__SILICON_REVISION__ < 3)
+/* Erroneous exception when enabling cache */
+#define ANOMALY_05000125 (__SILICON_REVISION__ < 3)
+/* SPI clock polarity and phase bits incorrect during booting */
+#define ANOMALY_05000126 (__SILICON_REVISION__ < 3)
+/* DMEM_CONTROL is not set on Reset */
+#define ANOMALY_05000137 (__SILICON_REVISION__ < 3)
+/* SPI boot will not complete if there is a zero fill block in the loader file */
+#define ANOMALY_05000138 (__SILICON_REVISION__ < 3)
+/* Allowing the SPORT RX FIFO to fill will cause an overflow */
+#define ANOMALY_05000140 (__SILICON_REVISION__ < 3)
+/* An Infinite Stall occurs with a particular sequence of consecutive dual dag events */
+#define ANOMALY_05000141 (__SILICON_REVISION__ < 3)
+/* Interrupts may be lost when a programmable input flag is configured to be edge sensitive */
+#define ANOMALY_05000142 (__SILICON_REVISION__ < 3)
+/* A read from external memory may return a wrong value with data cache enabled */
+#define ANOMALY_05000143 (__SILICON_REVISION__ < 3)
+/* DMA and TESTSET conflict when both are accessing external memory */
+#define ANOMALY_05000144 (__SILICON_REVISION__ < 3)
+/* In PWM_OUT mode, you must enable the PPI block to generate a waveform from PPI_CLK */
+#define ANOMALY_05000145 (__SILICON_REVISION__ < 3)
+/* MDMA may lose the first few words of a descriptor chain */
+#define ANOMALY_05000146 (__SILICON_REVISION__ < 3)
+/* The source MDMA descriptor may stop with a DMA Error */
+#define ANOMALY_05000147 (__SILICON_REVISION__ < 3)
+/* When booting from a 16-bit asynchronous memory device, the upper 8-bits of each word must be 0x00 */
+#define ANOMALY_05000148 (__SILICON_REVISION__ < 3)
+/* Frame Delay in SPORT Multichannel Mode */
+#define ANOMALY_05000153 (__SILICON_REVISION__ < 3)
+/* SPORT TFS signal is active in Multi-channel mode outside of valid channels */
+#define ANOMALY_05000154 (__SILICON_REVISION__ < 3)
+/* Timer1 can not be used for PWMOUT mode when a certain PPI mode is in use */
+#define ANOMALY_05000155 (__SILICON_REVISION__ < 3)
+/* A killed 32-bit System MMR write will lead to the next system MMR access thinking it should be 32-bit. */
+#define ANOMALY_05000157 (__SILICON_REVISION__ < 3)
+/* SPORT transmit data is not gated by external frame sync in certain conditions */
+#define ANOMALY_05000163 (__SILICON_REVISION__ < 3)
+/* SDRAM auto-refresh and subsequent Power Ups */
+#define ANOMALY_05000168 (__SILICON_REVISION__ < 3)
+/* DATA CPLB page miss can result in lost write-through cache data writes */
+#define ANOMALY_05000169 (__SILICON_REVISION__ < 3)
+/* DMA vs Core accesses to external memory */
+#define ANOMALY_05000173 (__SILICON_REVISION__ < 3)
+/* Cache Fill Buffer Data lost */
+#define ANOMALY_05000174 (__SILICON_REVISION__ < 3)
+/* Overlapping Sequencer and Memory Stalls */
+#define ANOMALY_05000175 (__SILICON_REVISION__ < 3)
+/* Multiplication of (-1) by (-1) followed by an accumulator saturation */
+#define ANOMALY_05000176 (__SILICON_REVISION__ < 3)
+/* Disabling the PPI resets the PPI configuration registers */
+#define ANOMALY_05000181 (__SILICON_REVISION__ < 3)
+/* PPI TX Mode with 2 External Frame Syncs */
+#define ANOMALY_05000185 (__SILICON_REVISION__ < 3)
+/* PPI does not invert the Driving PPICLK edge in Transmit Modes */
+#define ANOMALY_05000191 (__SILICON_REVISION__ < 3)
+/* In PPI Transmit Modes with External Frame Syncs POLC */
+#define ANOMALY_05000192 (__SILICON_REVISION__ < 3)
+/* Internal Voltage Regulator may not start up */
+#define ANOMALY_05000206 (__SILICON_REVISION__ < 3)
 
-#if defined(CONFIG_BF_REV_0_2)
-#define ANOMALY_05000067 /* Watchpoints (Hardware Breakpoints) are not
-                          *  supported */
-#define ANOMALY_05000109 /* Reserved bits in SYSCFG register not set at
-                          *  power on */
-#define ANOMALY_05000116 /* Trace Buffers may record discontinuities into
-                          *  emulation mode and/or exception, NMI, reset
-                          *  handlers */
-#define ANOMALY_05000123 /* DTEST_COMMAND initiated memory access may be
-                          *  incorrect if data cache or DMA is active */
-#define ANOMALY_05000124 /* DMA Lock-up at CCLK to SCLK ratios of 4:1, 2:1,
-                          *  or 1:1 */
-#define ANOMALY_05000125 /* Erroneous exception when enabling cache */
-#define ANOMALY_05000126 /* SPI clock polarity and phase bits incorrect
-                          *  during booting */
-#define ANOMALY_05000137 /* DMEM_CONTROL is not set on Reset */
-#define ANOMALY_05000138 /* SPI boot will not complete if there is a zero fill
-                          * block in the loader file */
-#define ANOMALY_05000140 /* Allowing the SPORT RX FIFO to fill will cause an
-                          *  overflow */
-#define ANOMALY_05000141 /* An Infinite Stall occurs with a particular sequence
-                          *  of consecutive dual dag events */
-#define ANOMALY_05000142 /* Interrupts may be lost when a programmable input
-                          *  flag is configured to be edge sensitive */
-#define ANOMALY_05000143 /* A read from external memory may return a wrong
-                          *  value with data cache enabled */
-#define ANOMALY_05000144 /* DMA and TESTSET conflict when both are accessing
-                          *  external memory */
-#define ANOMALY_05000145 /* In PWM_OUT mode, you must enable the PPI block to
-                          *  generate a waveform from PPI_CLK */
-#define ANOMALY_05000146 /* MDMA may lose the first few words of a descriptor
-                          *  chain */
-#define ANOMALY_05000147 /* The source MDMA descriptor may stop with a DMA
-                          *  Error */
-#define ANOMALY_05000148 /* When booting from a 16-bit asynchronous memory
-                          *  device, the upper 8-bits of each word must be
-                          *  0x00 */
-#define ANOMALY_05000153 /* Frame Delay in SPORT Multichannel Mode */
-#define ANOMALY_05000154 /* SPORT TFS signal is active in Multi-channel mode
-                          *  outside of valid channels */
-#define ANOMALY_05000155 /* Timer1 can not be used for PWMOUT mode when a
-                          *  certain PPI mode is in use */
-#define ANOMALY_05000157 /* A killed 32-bit System MMR write will lead to
-                          *  the next system MMR access thinking it should be
-                          *  32-bit. */
-#define ANOMALY_05000163 /* SPORT transmit data is not gated by external frame
-                          *  sync in certain conditions */
-#define ANOMALY_05000168 /* SDRAM auto-refresh and subsequent Power Ups */
-#define ANOMALY_05000169 /* DATA CPLB page miss can result in lost
-                          *  write-through cache data writes */
-#define ANOMALY_05000173 /* DMA vs Core accesses to external memory */
-#define ANOMALY_05000174 /* Cache Fill Buffer Data lost */
-#define ANOMALY_05000175 /* Overlapping Sequencer and Memory Stalls */
-#define ANOMALY_05000176 /* Multiplication of (-1) by (-1) followed by an
-                          *  accumulator saturation */
-#define ANOMALY_05000181 /* Disabling the PPI resets the PPI configuration
-                          *  registers */
-#define ANOMALY_05000185 /* PPI TX Mode with 2 External Frame Syncs */
-#define ANOMALY_05000191 /* PPI does not invert the Driving PPICLK edge in
-                          *  Transmit Modes */
-#define ANOMALY_05000192 /* In PPI Transmit Modes with External Frame Syncs
-                          *  POLC */
-#define ANOMALY_05000206 /* Internal Voltage Regulator may not start up */
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000266 (0)
 
 #endif
-
-#endif /*  _MACH_ANOMALY_H_ */