[ARM] 2861/1: PXA: Add some extra pxa27x register definitions

Patch from Richard Purdie

Add some extra pxa27x register definitions needed for the Sharp
SL-C3000 (Spitz).

Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 29 insertions, 0 deletions

diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h
index 51f0fe0ac165..939d9e5020a0 100644
--- a/include/asm-arm/arch-pxa/pxa-regs.h
+++ b/include/asm-arm/arch-pxa/pxa-regs.h
@@ -818,6 +818,23 @@
 #define UDCOTGICR_IEIDF (1 << 0)        /* OTG ID Change Falling Edge
                                            Interrupt Enable */
 
+#define UP2OCR            __REG(0x40600020)  /* USB Port 2 Output Control register */
+
+#define UP2OCR_CPVEN    (1 << 0)        /* Charge Pump Vbus Enable */
+#define UP2OCR_CPVPE    (1 << 1)        /* Charge Pump Vbus Pulse Enable */
+#define UP2OCR_DPPDE    (1 << 2)        /* Host Port 2 Transceiver D+ Pull Down Enable */
+#define UP2OCR_DMPDE    (1 << 3)        /* Host Port 2 Transceiver D- Pull Down Enable */
+#define UP2OCR_DPPUE    (1 << 4)        /* Host Port 2 Transceiver D+ Pull Up Enable */
+#define UP2OCR_DMPUE    (1 << 5)        /* Host Port 2 Transceiver D- Pull Up Enable */
+#define UP2OCR_DPPUBE   (1 << 6)        /* Host Port 2 Transceiver D+ Pull Up Bypass Enable */
+#define UP2OCR_DMPUBE   (1 << 7)        /* Host Port 2 Transceiver D- Pull Up Bypass Enable */
+#define UP2OCR_EXSP             (1 << 8)        /* External Transceiver Speed Control */
+#define UP2OCR_EXSUS    (1 << 9)        /* External Transceiver Speed Enable */
+#define UP2OCR_IDON             (1 << 10)       /* OTG ID Read Enable */
+#define UP2OCR_HXS              (1 << 16)       /* Host Port 2 Transceiver Output Select */
+#define UP2OCR_HXOE             (1 << 17)       /* Host Port 2 Transceiver Output Enable */
+#define UP2OCR_SEOS             (1 << 24)       /* Single-Ended Output Select */
+
 #define UDCCSN(x)       __REG2(0x40600100, (x) << 2)
 #define UDCCSR0         __REG(0x40600100) /* UDC Control/Status register - Endpoint 0 */
 #define UDCCSR0_SA      (1 << 7)        /* Setup Active */
@@ -1423,6 +1440,7 @@
 #define GPIO84_NSSP_RX          (84 | GPIO_ALT_FN_2_IN)
 #define GPIO85_nPCE_1_MD        (85 | GPIO_ALT_FN_1_OUT)
 #define GPIO92_MMCDAT0_MD       (92 | GPIO_ALT_FN_1_OUT)
+#define GPIO104_pSKTSEL_MD      (104 | GPIO_ALT_FN_1_OUT)
 #define GPIO109_MMCDAT1_MD      (109 | GPIO_ALT_FN_1_OUT)
 #define GPIO110_MMCDAT2_MD      (110 | GPIO_ALT_FN_1_OUT)
 #define GPIO110_MMCCS0_MD       (110 | GPIO_ALT_FN_1_OUT)
@@ -1510,6 +1528,8 @@
 #define PSSR_BFS        (1 << 1)        /* Battery Fault Status */
 #define PSSR_SSS        (1 << 0)        /* Software Sleep Status */
 
+#define PSLR_SL_ROD     (1 << 20)       /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */
+
 #define PCFR_RO         (1 << 15)       /* RDH Override */
 #define PCFR_PO         (1 << 14)       /* PH Override */
 #define PCFR_GPROD      (1 << 12)       /* GPIO nRESET_OUT Disable */
@@ -1517,6 +1537,7 @@
 #define PCFR_FVC        (1 << 10)       /* Frequency/Voltage Change */
 #define PCFR_DC_EN      (1 << 7)        /* Sleep/deep-sleep DC-DC Converter Enable */
 #define PCFR_PI2CEN     (1 << 6)        /* Enable PI2C controller */
+#define PCFR_GPR_EN     (1 << 4)        /* nRESET_GPIO Pin Enable */
 #define PCFR_DS         (1 << 3)        /* Deep Sleep Mode */
 #define PCFR_FS         (1 << 2)        /* Float Static Chip Selects */
 #define PCFR_FP         (1 << 1)        /* Float PCMCIA controls */
@@ -1810,6 +1831,11 @@
 #define LCCR0_PDD_S     12
 #define LCCR0_BM        (1 << 20)       /* Branch mask */
 #define LCCR0_OUM       (1 << 21)       /* Output FIFO underrun mask */
+#define LCCR0_LCDT      (1 << 22)       /* LCD panel type */
+#define LCCR0_RDSTM     (1 << 23)       /* Read status interrupt mask */
+#define LCCR0_CMDIM     (1 << 24)       /* Command interrupt mask */
+#define LCCR0_OUC       (1 << 25)       /* Overlay Underlay control bit */
+#define LCCR0_LDDALT    (1 << 26)       /* LDD alternate mapping control */
 
 #define LCCR1_PPL       Fld (10, 0)      /* Pixels Per Line - 1 */
 #define LCCR1_DisWdth(Pixel)            /* Display Width [1..800 pix.]  */ \
@@ -2062,7 +2088,10 @@
 #define UHCFMN          __REG(0x4C00003C) /* UHC Frame Number */
 #define UHCPERS         __REG(0x4C000040) /* UHC Periodic Start */
 #define UHCLS           __REG(0x4C000044) /* UHC Low Speed Threshold */
+
 #define UHCRHDA         __REG(0x4C000048) /* UHC Root Hub Descriptor A */
+#define UHCRHDA_NOCP    (1 << 12)       /* No over current protection */
+
 #define UHCRHDB         __REG(0x4C00004C) /* UHC Root Hub Descriptor B */
 #define UHCRHS          __REG(0x4C000050) /* UHC Root Hub Status */
 #define UHCRHPS1        __REG(0x4C000054) /* UHC Root Hub Port 1 Status */