[PATCH] SPI: spi_butterfly, restore lost deltas

This resolves some minor version skew glitches that accumulated for the AVR
Butterfly adapter driver, which caused among other things the existence of
a duplicate Kconfig entry.  Most of it boils down to comment updates, but in
one case it removes some now-superfluous code that would be better if not
copied into other controller-level drivers.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

2 files changed, 17 insertions, 29 deletions

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index b77dbd63e596..7a75faeb0526 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -75,16 +75,6 @@ config SPI_BUTTERFLY
           inexpensive battery powered microcontroller evaluation board.
           This same cable can be used to flash new firmware.
 
-config SPI_BUTTERFLY
-        tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
-        depends on SPI_MASTER && PARPORT && EXPERIMENTAL
-        select SPI_BITBANG
-        help
-          This uses a custom parallel port cable to connect to an AVR
-          Butterfly <http://www.atmel.com/products/avr/butterfly>, an
-          inexpensive battery powered microcontroller evaluation board.
-          This same cable can be used to flash new firmware.
-
 #
 # Add new SPI master controllers in alphabetical order above this line
 #
diff --git a/drivers/spi/spi_butterfly.c b/drivers/spi/spi_butterfly.c
index 79a3c59615ab..ff9e5faa4dc9 100644
--- a/drivers/spi/spi_butterfly.c
+++ b/drivers/spi/spi_butterfly.c
@@ -163,21 +163,20 @@ static void butterfly_chipselect(struct spi_device *spi, int value)
         struct butterfly        *pp = spidev_to_pp(spi);
 
         /* set default clock polarity */
-        if (value)
+        if (value != BITBANG_CS_INACTIVE)
                 setsck(spi, spi->mode & SPI_CPOL);
 
         /* no chipselect on this USI link config */
         if (is_usidev(spi))
                 return;
 
-        /* here, value == "activate or not" */
-
-        /* most PARPORT_CONTROL_* bits are negated */
+        /* here, value == "activate or not";
+         * most PARPORT_CONTROL_* bits are negated, so we must
+         * morph it to value == "bit value to write in control register"
+         */
         if (spi_cs_bit == PARPORT_CONTROL_INIT)
                 value = !value;
 
-        /* here, value == "bit value to write in control register"  */
-
         parport_frob_control(pp->port, spi_cs_bit, value ? spi_cs_bit : 0);
 }
 
@@ -202,7 +201,9 @@ butterfly_txrx_word_mode0(struct spi_device *spi,
 
 /* override default partitioning with cmdlinepart */
 static struct mtd_partition partitions[] = { {
-        /* JFFS2 wants partitions of 4*N blocks for this device ... */
+        /* JFFS2 wants partitions of 4*N blocks for this device,
+         * so sectors 0 and 1 can't be partitions by themselves.
+         */
 
         /* sector 0 = 8 pages * 264 bytes/page (1 block)
          * sector 1 = 248 pages * 264 bytes/page
@@ -316,8 +317,9 @@ static void butterfly_attach(struct parport *p)
         if (status < 0)
                 goto clean2;
 
-        /* Bus 1 lets us talk to at45db041b (firmware disables AVR)
-         * or AVR (firmware resets at45, acts as spi slave)
+        /* Bus 1 lets us talk to at45db041b (firmware disables AVR SPI), AVR
+         * (firmware resets at45, acts as spi slave) or neither (we ignore
+         * both, AVR uses AT45).  Here we expect firmware for the first option.
          */
         pp->info[0].max_speed_hz = 15 * 1000 * 1000;
         strcpy(pp->info[0].modalias, "mtd_dataflash");
@@ -330,7 +332,9 @@ static void butterfly_attach(struct parport *p)
                                 pp->dataflash->dev.bus_id);
 
 #ifdef  HAVE_USI
-        /* even more custom AVR firmware */
+        /* Bus 2 is only for talking to the AVR, and it can work no
+         * matter who masters bus 1; needs appropriate AVR firmware.
+         */
         pp->info[1].max_speed_hz = 10 /* ?? */ * 1000 * 1000;
         strcpy(pp->info[1].modalias, "butterfly");
         // pp->info[1].platform_data = ... TBD ... ;
@@ -378,13 +382,8 @@ static void butterfly_detach(struct parport *p)
         pp = butterfly;
         butterfly = NULL;
 
-#ifdef  HAVE_USI
-        spi_unregister_device(pp->butterfly);
-        pp->butterfly = NULL;
-#endif
-        spi_unregister_device(pp->dataflash);
-        pp->dataflash = NULL;
-
+        /* stop() unregisters child devices too */
+        pdev = to_platform_device(pp->bitbang.master->cdev.dev);
         status = spi_bitbang_stop(&pp->bitbang);
 
         /* turn off VCC */
@@ -394,8 +393,6 @@ static void butterfly_detach(struct parport *p)
         parport_release(pp->pd);
         parport_unregister_device(pp->pd);
 
-        pdev = to_platform_device(pp->bitbang.master->cdev.dev);
-
         (void) spi_master_put(pp->bitbang.master);
 
         platform_device_unregister(pdev);
@@ -420,4 +417,5 @@ static void __exit butterfly_exit(void)
 }
 module_exit(butterfly_exit);
 
+MODULE_DESCRIPTION("Parport Adapter driver for AVR Butterfly");
 MODULE_LICENSE("GPL");