[POWERPC] Generalize tsi108 PHY types

Add a phy_type field to the tsi108 ethernet structures to indicate which PHY
is used on a board.  This is derived from the "compatible" property in the
ethernet-phy node of the device tree.  The default remains the MV88E PHY.

Also, convert the setup code to use of_get_mac_address instead of hard coding
a lookup for the "address" property in the ethernet node.

Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>

2 files changed, 7 insertions, 14 deletions

diff --git a/drivers/net/tsi108_eth.c b/drivers/net/tsi108_eth.c
index 0bfc2c9c1c08..1aabc91f6458 100644
--- a/drivers/net/tsi108_eth.c
+++ b/drivers/net/tsi108_eth.c
@@ -82,6 +82,7 @@ struct tsi108_prv_data {
         unsigned int phy;               /* Index of PHY for this interface */
         unsigned int irq_num;
         unsigned int id;
+        unsigned int phy_type;
 
         struct timer_list timer;/* Timer that triggers the check phy function */
         unsigned int rxtail;    /* Next entry in rxring to read */
@@ -1256,11 +1257,11 @@ static void tsi108_init_phy(struct net_device *dev)
         if (i == 0)
                 printk(KERN_ERR "%s function time out \n", __FUNCTION__);
 
-#if (TSI108_PHY_TYPE == PHY_BCM54XX)    /* Broadcom BCM54xx PHY */
-        tsi108_write_mii(data, 0x09, 0x0300);
-        tsi108_write_mii(data, 0x10, 0x1020);
-        tsi108_write_mii(data, 0x1c, 0x8c00);
-#endif
+        if (data->phy_type == TSI108_PHY_BCM54XX) {
+                tsi108_write_mii(data, 0x09, 0x0300);
+                tsi108_write_mii(data, 0x10, 0x1020);
+                tsi108_write_mii(data, 0x1c, 0x8c00);
+        }
 
         tsi108_write_mii(data,
                          MII_BMCR,
@@ -1587,6 +1588,7 @@ tsi108_init_one(struct platform_device *pdev)
         data->mii_if.supports_gmii = mii_check_gmii_support(&data->mii_if);
 
         data->phy = einfo->phy;
+        data->phy_type = einfo->phy_type;
         data->irq_num = einfo->irq_num;
         data->id = pdev->id;
         dev->open = tsi108_open;
diff --git a/drivers/net/tsi108_eth.h b/drivers/net/tsi108_eth.h
index 77a769df228a..5a77ae6c5f36 100644
--- a/drivers/net/tsi108_eth.h
+++ b/drivers/net/tsi108_eth.h
@@ -43,15 +43,6 @@
         in_be32((data->phyregs + (offset)))
 
 /*
- * PHY Configuration Options
- *
- * NOTE: Enable set of definitions corresponding to your board type
- */
-#define PHY_MV88E       1       /* Marvel 88Exxxx PHY */
-#define PHY_BCM54XX     2       /* Broardcom BCM54xx PHY */
-#define TSI108_PHY_TYPE PHY_MV88E
-
-/*
  * TSI108 GIGE port registers
  */