Merge ../linux-2.6

15 files changed, 633 insertions, 23 deletions

diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig
index 5a8a2c91c2b2..5c60be521561 100644
--- a/drivers/usb/serial/Kconfig
+++ b/drivers/usb/serial/Kconfig
@@ -71,6 +71,16 @@ config USB_SERIAL_ANYDATA
           To compile this driver as a module, choose M here: the
           module will be called anydata.
 
+config USB_SERIAL_ARK3116
+        tristate "USB ARK Micro 3116 USB Serial Driver (EXPERIMENTAL)"
+        depends on USB_SERIAL && EXPERIMENTAL
+        help
+          Say Y here if you want to use a ARK Micro 3116 USB to Serial
+          device.
+
+          To compile this driver as a module, choose M here: the
+          module will be called ark3116
+
 config USB_SERIAL_BELKIN
         tristate "USB Belkin and Peracom Single Port Serial Driver"
         depends on USB_SERIAL
@@ -158,6 +168,15 @@ config USB_SERIAL_FTDI_SIO
           To compile this driver as a module, choose M here: the
           module will be called ftdi_sio.
 
+config USB_SERIAL_FUNSOFT
+        tristate "USB Fundamental Software Dongle Driver"
+        depends on USB_SERIAL
+        ---help---
+          Say Y here if you want to use the Fundamental Software dongle.
+
+          To compile this driver as a module, choose M here: the
+          module will be called funsoft.
+
 config USB_SERIAL_VISOR
         tristate "USB Handspring Visor / Palm m50x / Sony Clie Driver"
         depends on USB_SERIAL
diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile
index f7fe4172efed..5a0960fc9d3e 100644
--- a/drivers/usb/serial/Makefile
+++ b/drivers/usb/serial/Makefile
@@ -13,6 +13,7 @@ usbserial-objs	:= usb-serial.o generic.o bus.o $(usbserial-obj-y)
 
 obj-$(CONFIG_USB_SERIAL_AIRPRIME)               += airprime.o
 obj-$(CONFIG_USB_SERIAL_ANYDATA)                += anydata.o
+obj-$(CONFIG_USB_SERIAL_ARK3116)                += ark3116.o
 obj-$(CONFIG_USB_SERIAL_BELKIN)                 += belkin_sa.o
 obj-$(CONFIG_USB_SERIAL_CP2101)                 += cp2101.o
 obj-$(CONFIG_USB_SERIAL_CYBERJACK)              += cyberjack.o
@@ -22,6 +23,7 @@ obj-$(CONFIG_USB_SERIAL_EDGEPORT)		+= io_edgeport.o
 obj-$(CONFIG_USB_SERIAL_EDGEPORT_TI)            += io_ti.o
 obj-$(CONFIG_USB_SERIAL_EMPEG)                  += empeg.o
 obj-$(CONFIG_USB_SERIAL_FTDI_SIO)               += ftdi_sio.o
+obj-$(CONFIG_USB_SERIAL_FUNSOFT)                += funsoft.o
 obj-$(CONFIG_USB_SERIAL_GARMIN)                 += garmin_gps.o
 obj-$(CONFIG_USB_SERIAL_HP4X)                   += hp4x.o
 obj-$(CONFIG_USB_SERIAL_IPAQ)                   += ipaq.o
diff --git a/drivers/usb/serial/airprime.c b/drivers/usb/serial/airprime.c
index dbf1f063098c..694b205f9b73 100644
--- a/drivers/usb/serial/airprime.c
+++ b/drivers/usb/serial/airprime.c
@@ -18,6 +18,7 @@
 static struct usb_device_id id_table [] = {
         { USB_DEVICE(0xf3d, 0x0112) },  /* AirPrime CDMA Wireless PC Card */
         { USB_DEVICE(0x1410, 0x1110) }, /* Novatel Wireless Merlin CDMA */
+        { USB_DEVICE(0x1199, 0x0112) }, /* Sierra Wireless Aircard 580 */
         { },
 };
 MODULE_DEVICE_TABLE(usb, id_table);
diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c
new file mode 100644
index 000000000000..8dec796222a0
--- /dev/null
+++ b/drivers/usb/serial/ark3116.c
@@ -0,0 +1,465 @@
+/*
+ * ark3116
+ * - implements a driver for the arkmicro ark3116 chipset (vendor=0x6547,
+ *   productid=0x0232) (used in a datacable called KQ-U8A)
+ *
+ * - based on code by krisfx -> thanks !!
+ *   (see http://www.linuxquestions.org/questions/showthread.php?p=2184457#post2184457)
+ *
+ *  - based on logs created by usbsnoopy
+ *
+ *  Author   : Simon Schulz [ark3116_driver<AT>auctionant.de]
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include "usb-serial.h"
+
+
+static int debug;
+
+static struct usb_device_id id_table [] = {
+        { USB_DEVICE(0x6547, 0x0232) },
+        { },
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+struct ark3116_private {
+        spinlock_t lock;
+        u8 termios_initialized;
+};
+
+static inline void ARK3116_SND(struct usb_serial *serial, int seq,
+                               __u8 request, __u8 requesttype,
+                               __u16 value, __u16 index)
+{
+        int result;
+        result = usb_control_msg(serial->dev,
+                                 usb_sndctrlpipe(serial->dev,0),
+                                 request, requesttype, value, index,
+                                 NULL,0x00, 1000);
+        dbg("%03d > ok",seq);
+}
+
+static inline void ARK3116_RCV(struct usb_serial *serial, int seq,
+                               __u8 request, __u8 requesttype,
+                               __u16 value, __u16 index, __u8 expected,
+                               char *buf)
+{
+        int result;
+        result = usb_control_msg(serial->dev,
+                              usb_rcvctrlpipe(serial->dev,0),
+                              request, requesttype, value, index,
+                              buf, 0x0000001, 1000);
+        if (result)
+                dbg("%03d < %d bytes [0x%02X]",seq, result, buf[0]);
+        else
+                dbg("%03d < 0 bytes", seq);
+}
+
+
+static inline void ARK3116_RCV_QUIET(struct usb_serial *serial,
+                                     __u8 request, __u8 requesttype,
+                                     __u16 value, __u16 index, char *buf)
+{
+        usb_control_msg(serial->dev,
+                        usb_rcvctrlpipe(serial->dev,0),
+                        request, requesttype, value, index,
+                        buf, 0x0000001, 1000);
+}
+
+
+static int ark3116_attach(struct usb_serial *serial)
+{
+        char *buf;
+        struct ark3116_private *priv;
+        int i;
+
+        for (i = 0; i < serial->num_ports; ++i) {
+                priv = kmalloc (sizeof (struct ark3116_private), GFP_KERNEL);
+                if (!priv)
+                        goto cleanup;
+                memset (priv, 0x00, sizeof (struct ark3116_private));
+                spin_lock_init(&priv->lock);
+
+                usb_set_serial_port_data(serial->port[i], priv);
+        }
+
+        buf = kmalloc(1, GFP_KERNEL);
+        if (!buf) {
+                dbg("error kmalloc -> out of mem ?");
+                goto cleanup;
+        }
+
+        /* 3 */
+        ARK3116_SND(serial, 3,0xFE,0x40,0x0008,0x0002);
+        ARK3116_SND(serial, 4,0xFE,0x40,0x0008,0x0001);
+        ARK3116_SND(serial, 5,0xFE,0x40,0x0000,0x0008);
+        ARK3116_SND(serial, 6,0xFE,0x40,0x0000,0x000B);
+
+        /* <-- seq7 */
+        ARK3116_RCV(serial, 7,0xFE,0xC0,0x0000,0x0003, 0x00, buf);
+        ARK3116_SND(serial, 8,0xFE,0x40,0x0080,0x0003);
+        ARK3116_SND(serial, 9,0xFE,0x40,0x001A,0x0000);
+        ARK3116_SND(serial,10,0xFE,0x40,0x0000,0x0001);
+        ARK3116_SND(serial,11,0xFE,0x40,0x0000,0x0003);
+
+        /* <-- seq12 */
+        ARK3116_RCV(serial,12,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+        ARK3116_SND(serial,13,0xFE,0x40,0x0000,0x0004);
+
+        /* 14 */
+        ARK3116_RCV(serial,14,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+        ARK3116_SND(serial,15,0xFE,0x40,0x0000,0x0004);
+
+        /* 16 */
+        ARK3116_RCV(serial,16,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+        /* --> seq17 */
+        ARK3116_SND(serial,17,0xFE,0x40,0x0001,0x0004);
+
+        /* <-- seq18 */
+        ARK3116_RCV(serial,18,0xFE,0xC0,0x0000,0x0004, 0x01, buf);
+
+        /* --> seq19 */
+        ARK3116_SND(serial,19,0xFE,0x40,0x0003,0x0004);
+
+
+        /* <-- seq20 */
+        /* seems like serial port status info (RTS, CTS,...) */
+        /* returns modem control line status ?! */
+        ARK3116_RCV(serial,20,0xFE,0xC0,0x0000,0x0006, 0xFF, buf);
+
+        /* set 9600 baud & do some init ?! */
+        ARK3116_SND(serial,147,0xFE,0x40,0x0083,0x0003);
+        ARK3116_SND(serial,148,0xFE,0x40,0x0038,0x0000);
+        ARK3116_SND(serial,149,0xFE,0x40,0x0001,0x0001);
+        ARK3116_SND(serial,150,0xFE,0x40,0x0003,0x0003);
+        ARK3116_RCV(serial,151,0xFE,0xC0,0x0000,0x0004,0x03, buf);
+        ARK3116_SND(serial,152,0xFE,0x40,0x0000,0x0003);
+        ARK3116_RCV(serial,153,0xFE,0xC0,0x0000,0x0003,0x00, buf);
+        ARK3116_SND(serial,154,0xFE,0x40,0x0003,0x0003);
+
+        kfree(buf);
+        return(0);
+
+cleanup:
+        for (--i; i>=0; --i)
+                usb_set_serial_port_data(serial->port[i], NULL);
+        return -ENOMEM;
+}
+
+static void ark3116_set_termios(struct usb_serial_port *port,
+                                struct termios *old_termios)
+{
+        struct usb_serial *serial = port->serial;
+        struct ark3116_private *priv = usb_get_serial_port_data(port);
+        unsigned int cflag = port->tty->termios->c_cflag;
+        unsigned long flags;
+        int baud;
+        int ark3116_baud;
+        char *buf;
+        char config;
+
+        config = 0;
+
+        dbg("%s - port %d", __FUNCTION__, port->number);
+
+        if ((!port->tty) || (!port->tty->termios)) {
+                dbg("%s - no tty structures", __FUNCTION__);
+                return;
+        }
+
+        spin_lock_irqsave(&priv->lock, flags);
+        if (!priv->termios_initialized) {
+                *(port->tty->termios) = tty_std_termios;
+                port->tty->termios->c_cflag = B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+                priv->termios_initialized = 1;
+        }
+        spin_unlock_irqrestore(&priv->lock, flags);
+
+        cflag = port->tty->termios->c_cflag;
+
+        /* check that they really want us to change something: */
+        if (old_termios) {
+                if ((cflag == old_termios->c_cflag) &&
+                    (RELEVANT_IFLAG(port->tty->termios->c_iflag) ==
+                     RELEVANT_IFLAG(old_termios->c_iflag))) {
+                        dbg("%s - nothing to change...", __FUNCTION__);
+                        return;
+                }
+        }
+
+        buf = kmalloc(1, GFP_KERNEL);
+        if (!buf) {
+                dbg("error kmalloc");
+                return;
+        }
+
+        /* set data bit count (8/7/6/5) */
+        if (cflag & CSIZE){
+                switch (cflag & CSIZE){
+                case CS5:
+                        config |= 0x00;
+                        dbg("setting CS5");
+                        break;
+                case CS6:
+                        config |= 0x01;
+                        dbg("setting CS6");
+                        break;
+                case CS7:
+                        config |= 0x02;
+                        dbg("setting CS7");
+                        break;
+                default:
+                        err ("CSIZE was set but not CS5-CS8, using CS8!");
+                case CS8:
+                        config |= 0x03;
+                        dbg("setting CS8");
+                        break;
+                }
+        }
+
+        /* set parity (NONE,EVEN,ODD) */
+        if (cflag & PARENB){
+                if (cflag & PARODD) {
+                        config |= 0x08;
+                        dbg("setting parity to ODD");
+                } else {
+                        config |= 0x18;
+                        dbg("setting parity to EVEN");
+                }
+        } else {
+                dbg("setting parity to NONE");
+        }
+
+        /* SET STOPBIT (1/2) */
+        if (cflag & CSTOPB) {
+                config |= 0x04;
+                dbg ("setting 2 stop bits");
+        } else {
+                dbg ("setting 1 stop bit");
+        }
+
+
+        /* set baudrate: */
+        baud = 0;
+        switch (cflag & CBAUD){
+                case B0:
+                        err("can't set 0baud, using 9600 instead");
+                        break;
+                case B75:       baud = 75;      break;
+                case B150:      baud = 150;     break;
+                case B300:      baud = 300;     break;
+                case B600:      baud = 600;     break;
+                case B1200:     baud = 1200;    break;
+                case B1800:     baud = 1800;    break;
+                case B2400:     baud = 2400;    break;
+                case B4800:     baud = 4800;    break;
+                case B9600:     baud = 9600;    break;
+                case B19200:    baud = 19200;   break;
+                case B38400:    baud = 38400;   break;
+                case B57600:    baud = 57600;   break;
+                case B115200:   baud = 115200;  break;
+                case B230400:   baud = 230400;  break;
+                case B460800:   baud = 460800;  break;
+                default:
+                        dbg("does not support the baudrate requested (fix it)");
+                        break;
+        }
+
+        /* set 9600 as default (if given baudrate is invalid for example) */
+        if (baud == 0)
+                baud = 9600;
+
+        /*
+         * found by try'n'error, be careful, maybe there are other options
+         * for multiplicator etc!
+         */
+        if (baud == 460800)
+                /* strange, for 460800 the formula is wrong
+                 * (dont use round(), then 9600baud is wrong) */
+                ark3116_baud = 7;
+        else
+                ark3116_baud = 3000000 / baud;
+
+        /* ? */
+        ARK3116_RCV(serial,0,0xFE,0xC0,0x0000,0x0003, 0x03, buf);
+        /* offset = buf[0]; */
+        /* offset = 0x03; */
+        /* dbg("using 0x%04X as target for 0x0003:",0x0080+offset); */
+
+
+        /* set baudrate */
+        dbg("setting baudrate to %d (->reg=%d)",baud,ark3116_baud);
+        ARK3116_SND(serial,147,0xFE,0x40,0x0083,0x0003);
+        ARK3116_SND(serial,148,0xFE,0x40,(ark3116_baud & 0x00FF)   ,0x0000);
+        ARK3116_SND(serial,149,0xFE,0x40,(ark3116_baud & 0xFF00)>>8,0x0001);
+        ARK3116_SND(serial,150,0xFE,0x40,0x0003,0x0003);
+
+        /* ? */
+        ARK3116_RCV(serial,151,0xFE,0xC0,0x0000,0x0004,0x03, buf);
+        ARK3116_SND(serial,152,0xFE,0x40,0x0000,0x0003);
+
+        /* set data bit count, stop bit count & parity: */
+        dbg("updating bit count, stop bit or parity (cfg=0x%02X)", config);
+        ARK3116_RCV(serial,153,0xFE,0xC0,0x0000,0x0003,0x00, buf);
+        ARK3116_SND(serial,154,0xFE,0x40,config,0x0003);
+
+        if (cflag & CRTSCTS)
+                dbg("CRTSCTS not supported by chipset ?!");
+
+        /* TEST ARK3116_SND(154,0xFE,0x40,0xFFFF, 0x0006); */
+
+        kfree(buf);
+        return;
+}
+
+static int ark3116_open(struct usb_serial_port *port, struct file *filp)
+{
+        struct termios tmp_termios;
+        struct usb_serial *serial = port->serial;
+        char *buf;
+        int result = 0;
+
+        dbg("%s -  port %d", __FUNCTION__, port->number);
+
+        buf = kmalloc(1, GFP_KERNEL);
+        if (!buf) {
+                dbg("error kmalloc -> out of mem ?");
+                return -ENOMEM;
+        }
+
+        result = usb_serial_generic_open(port, filp);
+        if (result)
+                return result;
+
+        /* open */
+        ARK3116_RCV(serial,111,0xFE,0xC0,0x0000,0x0003, 0x02, buf);
+
+        ARK3116_SND(serial,112,0xFE,0x40,0x0082,0x0003);
+        ARK3116_SND(serial,113,0xFE,0x40,0x001A,0x0000);
+        ARK3116_SND(serial,114,0xFE,0x40,0x0000,0x0001);
+        ARK3116_SND(serial,115,0xFE,0x40,0x0002,0x0003);
+
+        ARK3116_RCV(serial,116,0xFE,0xC0,0x0000,0x0004, 0x03, buf);
+        ARK3116_SND(serial,117,0xFE,0x40,0x0002,0x0004);
+
+        ARK3116_RCV(serial,118,0xFE,0xC0,0x0000,0x0004, 0x02, buf);
+        ARK3116_SND(serial,119,0xFE,0x40,0x0000,0x0004);
+
+        ARK3116_RCV(serial,120,0xFE,0xC0,0x0000,0x0004, 0x00, buf);
+
+        ARK3116_SND(serial,121,0xFE,0x40,0x0001,0x0004);
+
+        ARK3116_RCV(serial,122,0xFE,0xC0,0x0000,0x0004, 0x01, buf);
+
+        ARK3116_SND(serial,123,0xFE,0x40,0x0003,0x0004);
+
+        /* returns different values (control lines ?!) */
+        ARK3116_RCV(serial,124,0xFE,0xC0,0x0000,0x0006, 0xFF, buf);
+
+        /* initialise termios: */
+        if (port->tty)
+                ark3116_set_termios(port, &tmp_termios);
+
+        kfree(buf);
+
+        return result;
+
+}
+
+static int ark3116_ioctl(struct usb_serial_port *port, struct file *file,
+                         unsigned int cmd, unsigned long arg)
+{
+        dbg("ioctl not supported yet...");
+        return -ENOIOCTLCMD;
+}
+
+static int ark3116_tiocmget(struct usb_serial_port *port, struct file *file)
+{
+        struct usb_serial *serial = port->serial;
+        char *buf;
+        char temp;
+
+        /* seems like serial port status info (RTS, CTS,...) is stored
+         * in reg(?) 0x0006
+         * pcb connection point 11 = GND -> sets bit4 of response
+         * pcb connection point  7 = GND -> sets bit6 of response
+         */
+
+        buf = kmalloc(1, GFP_KERNEL);
+        if (!buf) {
+                dbg("error kmalloc");
+                return -ENOMEM;
+        }
+
+        /* read register: */
+        ARK3116_RCV_QUIET(serial,0xFE,0xC0,0x0000,0x0006,buf);
+        temp = buf[0];
+        kfree(buf);
+
+        /* i do not really know if bit4=CTS and bit6=DSR... was just a
+         * quick guess !!
+         */
+        return  (temp & (1<<4) ? TIOCM_CTS : 0) |
+                (temp & (1<<6) ? TIOCM_DSR : 0);
+}
+
+static struct usb_driver ark3116_driver = {
+        .name =         "ark3116",
+        .probe =        usb_serial_probe,
+        .disconnect =   usb_serial_disconnect,
+        .id_table =     id_table,
+};
+
+static struct usb_serial_driver ark3116_device = {
+        .driver = {
+                .owner =        THIS_MODULE,
+                .name =         "ark3116",
+        },
+        .id_table =             id_table,
+        .num_interrupt_in =     1,
+        .num_bulk_in =          1,
+        .num_bulk_out =         1,
+        .num_ports =            1,
+        .attach =               ark3116_attach,
+        .set_termios =          ark3116_set_termios,
+        .ioctl =                ark3116_ioctl,
+        .tiocmget =             ark3116_tiocmget,
+        .open =                 ark3116_open,
+};
+
+static int __init ark3116_init(void)
+{
+        int retval;
+
+        retval = usb_serial_register(&ark3116_device);
+        if (retval)
+                return retval;
+        retval = usb_register(&ark3116_driver);
+        if (retval)
+                usb_serial_deregister(&ark3116_device);
+        return retval;
+}
+
+static void __exit ark3116_exit(void)
+{
+        usb_deregister(&ark3116_driver);
+        usb_serial_deregister(&ark3116_device);
+}
+
+module_init(ark3116_init);
+module_exit(ark3116_exit);
+MODULE_LICENSE("GPL");
+
+module_param(debug, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Debug enabled or not");
+
diff --git a/drivers/usb/serial/console.c b/drivers/usb/serial/console.c
index 167f8ec56131..8023bb7279b1 100644
--- a/drivers/usb/serial/console.c
+++ b/drivers/usb/serial/console.c
@@ -54,7 +54,7 @@ static struct console usbcons;
  * serial.c code, except that the specifier is "ttyUSB" instead
  * of "ttyS".
  */
-static int __init usb_console_setup(struct console *co, char *options)
+static int usb_console_setup(struct console *co, char *options)
 {
         struct usbcons_info *info = &usbcons_info;
         int baud = 9600;
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index f3af81b4dd29..986d7622273d 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -307,7 +307,9 @@ static struct ftdi_sio_quirk ftdi_HE_TIRA1_quirk = {
 
 
 static struct usb_device_id id_table_combined [] = {
+        { USB_DEVICE(FTDI_VID, FTDI_ACTZWAVE_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_IRTRANS_PID) },
+        { USB_DEVICE(FTDI_VID, FTDI_IPLUS_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_SIO_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_8U232AM_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_8U232AM_ALT_PID) },
@@ -489,10 +491,15 @@ static struct usb_device_id id_table_combined [] = {
         { USB_DEVICE(KOBIL_VID, KOBIL_CONV_KAAN_PID) },
         { USB_DEVICE(POSIFLEX_VID, POSIFLEX_PP7000_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_TTUSB_PID) },
+        { USB_DEVICE(FTDI_VID, FTDI_ECLO_COM_1WIRE_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_777_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_WESTREX_MODEL_8900F_PID) },
         { USB_DEVICE(FTDI_VID, FTDI_PCDJ_DAC2_PID) },
+        { USB_DEVICE(FTDI_VID, FTDI_RRCIRKITS_LOCOBUFFER_PID) },
+        { USB_DEVICE(FTDI_VID, FTDI_ASK_RDR400_PID) },
         { USB_DEVICE(ICOM_ID1_VID, ICOM_ID1_PID) },
+        { USB_DEVICE(PAPOUCH_VID, PAPOUCH_TMU_PID) },
+        { USB_DEVICE(FTDI_VID, FTDI_ACG_HFDUAL_PID) },
         { },                                    /* Optional parameter entry */
         { }                                     /* Terminating entry */
 };
diff --git a/drivers/usb/serial/ftdi_sio.h b/drivers/usb/serial/ftdi_sio.h
index 8da773c2744d..d69a917e768f 100644
--- a/drivers/usb/serial/ftdi_sio.h
+++ b/drivers/usb/serial/ftdi_sio.h
@@ -32,6 +32,10 @@
 #define FTDI_NF_RIC_PID 0x0001  /* Product Id */
 
 
+/* ACT Solutions HomePro ZWave interface (http://www.act-solutions.com/HomePro.htm) */
+#define FTDI_ACTZWAVE_PID       0xF2D0
+
+
 /* www.irtrans.de device */
 #define FTDI_IRTRANS_PID 0xFC60 /* Product Id */
 
@@ -39,6 +43,9 @@
 /* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */
 #define FTDI_TTUSB_PID 0xFF20 /* Product Id */
 
+/* iPlus device */
+#define FTDI_IPLUS_PID 0xD070 /* Product Id */
+
 /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
 /* they use the ftdi chipset for the USB interface and the vendor id is the same */
 #define FTDI_XF_632_PID 0xFC08  /* 632: 16x2 Character Display */
@@ -153,6 +160,11 @@
 #define ICOM_ID1_PID            0x0004
 
 /*
+ * ASK.fr devices
+ */
+#define FTDI_ASK_RDR400_PID     0xC991  /* ASK RDR 400 series card reader */
+
+/*
  * DSS-20 Sync Station for Sony Ericsson P800
  */
  
@@ -399,6 +411,31 @@
 #define FTDI_WESTREX_MODEL_777_PID      0xDC00  /* Model 777 */
 #define FTDI_WESTREX_MODEL_8900F_PID    0xDC01  /* Model 8900F */
 
+/*
+ * RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com)
+ */
+#define FTDI_RRCIRKITS_LOCOBUFFER_PID   0xc7d0  /* LocoBuffer USB */
+
+/*
+ * Eclo (http://www.eclo.pt/) product IDs.
+ * PID 0xEA90 submitted by Martin Grill.
+ */
+#define FTDI_ECLO_COM_1WIRE_PID 0xEA90  /* COM to 1-Wire USB adaptor */
+
+/*
+ * Papouch products (http://www.papouch.com/)
+ * Submitted by Folkert van Heusden
+ */
+
+#define PAPOUCH_VID                     0x5050  /* Vendor ID */
+#define PAPOUCH_TMU_PID                 0x0400  /* TMU USB Thermometer */
+
+/*
+ * ACG Identification Technologies GmbH products (http://www.acg.de/).
+ * Submitted by anton -at- goto10 -dot- org.
+ */
+#define FTDI_ACG_HFDUAL_PID             0xDD20  /* HF Dual ISO Reader (RFID) */
+
 /* Commands */
 #define FTDI_SIO_RESET          0 /* Reset the port */
 #define FTDI_SIO_MODEM_CTRL     1 /* Set the modem control register */
diff --git a/drivers/usb/serial/funsoft.c b/drivers/usb/serial/funsoft.c
new file mode 100644
index 000000000000..803721b97e2e
--- /dev/null
+++ b/drivers/usb/serial/funsoft.c
@@ -0,0 +1,65 @@
+/*
+ * Funsoft Serial USB driver
+ *
+ * Copyright (C) 2006 Greg Kroah-Hartman <gregkh@suse.de>
+ *
+ *      This program is free software; you can redistribute it and/or
+ *      modify it under the terms of the GNU General Public License version
+ *      2 as published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include "usb-serial.h"
+
+static struct usb_device_id id_table [] = {
+        { USB_DEVICE(0x1404, 0xcddc) },
+        { },
+};
+MODULE_DEVICE_TABLE(usb, id_table);
+
+static struct usb_driver funsoft_driver = {
+        .name =         "funsoft",
+        .probe =        usb_serial_probe,
+        .disconnect =   usb_serial_disconnect,
+        .id_table =     id_table,
+        .no_dynamic_id =        1,
+};
+
+static struct usb_serial_driver funsoft_device = {
+        .driver = {
+                .owner =        THIS_MODULE,
+                .name =         "funsoft",
+        },
+        .id_table =             id_table,
+        .num_interrupt_in =     NUM_DONT_CARE,
+        .num_bulk_in =          NUM_DONT_CARE,
+        .num_bulk_out =         NUM_DONT_CARE,
+        .num_ports =            1,
+};
+
+static int __init funsoft_init(void)
+{
+        int retval;
+
+        retval = usb_serial_register(&funsoft_device);
+        if (retval)
+                return retval;
+        retval = usb_register(&funsoft_driver);
+        if (retval)
+                usb_serial_deregister(&funsoft_device);
+        return retval;
+}
+
+static void __exit funsoft_exit(void)
+{
+        usb_deregister(&funsoft_driver);
+        usb_serial_deregister(&funsoft_device);
+}
+
+module_init(funsoft_init);
+module_exit(funsoft_exit);
+MODULE_LICENSE("GPL");
diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c
index 476cda107f4f..c62cc2876519 100644
--- a/drivers/usb/serial/generic.c
+++ b/drivers/usb/serial/generic.c
@@ -138,6 +138,7 @@ int usb_serial_generic_open (struct usb_serial_port *port, struct file *filp)
 
         return result;
 }
+EXPORT_SYMBOL_GPL(usb_serial_generic_open);
 
 static void generic_cleanup (struct usb_serial_port *port)
 {
diff --git a/drivers/usb/serial/omninet.c b/drivers/usb/serial/omninet.c
index 4d40704dea2c..238033a87092 100644
--- a/drivers/usb/serial/omninet.c
+++ b/drivers/usb/serial/omninet.c
@@ -257,14 +257,14 @@ static int omninet_write (struct usb_serial_port *port, const unsigned char *buf
                 return (0);
         }
 
-        spin_lock(&port->lock);
-        if (port->write_urb_busy) {
-                spin_unlock(&port->lock);
+        spin_lock(&wport->lock);
+        if (wport->write_urb_busy) {
+                spin_unlock(&wport->lock);
                 dbg("%s - already writing", __FUNCTION__);
                 return 0;
         }
-        port->write_urb_busy = 1;
-        spin_unlock(&port->lock);
+        wport->write_urb_busy = 1;
+        spin_unlock(&wport->lock);
 
         count = (count > OMNINET_BULKOUTSIZE) ? OMNINET_BULKOUTSIZE : count;
 
@@ -283,7 +283,7 @@ static int omninet_write (struct usb_serial_port *port, const unsigned char *buf
         wport->write_urb->dev = serial->dev;
         result = usb_submit_urb(wport->write_urb, GFP_ATOMIC);
         if (result) {
-                port->write_urb_busy = 0;
+                wport->write_urb_busy = 0;
                 err("%s - failed submitting write urb, error %d", __FUNCTION__, result);
         } else
                 result = count;
diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c
index b3014fda645c..c96714bb1cb8 100644
--- a/drivers/usb/serial/pl2303.c
+++ b/drivers/usb/serial/pl2303.c
@@ -61,6 +61,7 @@ static struct usb_device_id id_table [] = {
         { USB_DEVICE(ELCOM_VENDOR_ID, ELCOM_PRODUCT_ID) },
         { USB_DEVICE(ELCOM_VENDOR_ID, ELCOM_PRODUCT_ID_UCSGT) },
         { USB_DEVICE(ITEGNO_VENDOR_ID, ITEGNO_PRODUCT_ID) },
+        { USB_DEVICE(ITEGNO_VENDOR_ID, ITEGNO_PRODUCT_ID_2080) },
         { USB_DEVICE(MA620_VENDOR_ID, MA620_PRODUCT_ID) },
         { USB_DEVICE(RATOC_VENDOR_ID, RATOC_PRODUCT_ID) },
         { USB_DEVICE(TRIPP_VENDOR_ID, TRIPP_PRODUCT_ID) },
@@ -78,6 +79,7 @@ static struct usb_device_id id_table [] = {
         { USB_DEVICE(SAGEM_VENDOR_ID, SAGEM_PRODUCT_ID) },
         { USB_DEVICE(LEADTEK_VENDOR_ID, LEADTEK_9531_PRODUCT_ID) },
         { USB_DEVICE(SPEEDDRAGON_VENDOR_ID, SPEEDDRAGON_PRODUCT_ID) },
+        { USB_DEVICE(OTI_VENDOR_ID, OTI_PRODUCT_ID) },
         { }                                     /* Terminating entry */
 };
 
diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h
index 77901d143979..7f29e81d3e35 100644
--- a/drivers/usb/serial/pl2303.h
+++ b/drivers/usb/serial/pl2303.h
@@ -26,6 +26,7 @@
 
 #define ITEGNO_VENDOR_ID        0x0eba
 #define ITEGNO_PRODUCT_ID       0x1080
+#define ITEGNO_PRODUCT_ID_2080  0x2080
 
 #define MA620_VENDOR_ID         0x0df7
 #define MA620_PRODUCT_ID        0x0620
@@ -79,3 +80,7 @@
 /* USB GSM cable from Speed Dragon Multimedia, Ltd */
 #define SPEEDDRAGON_VENDOR_ID   0x0e55
 #define SPEEDDRAGON_PRODUCT_ID  0x110b
+
+/* Ours Technology Inc DKU-5 clone, chipset: Prolific Technology Inc */
+#define OTI_VENDOR_ID   0x0ea0
+#define OTI_PRODUCT_ID  0x6858
diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c
index 097f4e8488fe..9c36f0ece20f 100644
--- a/drivers/usb/serial/usb-serial.c
+++ b/drivers/usb/serial/usb-serial.c
@@ -27,10 +27,10 @@
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/spinlock.h>
+#include <linux/mutex.h>
 #include <linux/list.h>
 #include <linux/smp_lock.h>
 #include <asm/uaccess.h>
-#include <asm/semaphore.h>
 #include <linux/usb.h>
 #include "usb-serial.h"
 #include "pl2303.h"
@@ -189,11 +189,15 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
 
         portNumber = tty->index - serial->minor;
         port = serial->port[portNumber];
-        if (!port)
-                return -ENODEV;
+        if (!port) {
+                retval = -ENODEV;
+                goto bailout_kref_put;
+        }
 
-        if (down_interruptible(&port->sem))
-                return -ERESTARTSYS;
+        if (mutex_lock_interruptible(&port->mutex)) {
+                retval = -ERESTARTSYS;
+                goto bailout_kref_put;
+        }
          
         ++port->open_count;
 
@@ -209,7 +213,7 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
                  * safe because we are called with BKL held */
                 if (!try_module_get(serial->type->driver.owner)) {
                         retval = -ENODEV;
-                        goto bailout_kref_put;
+                        goto bailout_mutex_unlock;
                 }
 
                 /* only call the device specific open if this 
@@ -219,15 +223,16 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
                         goto bailout_module_put;
         }
 
-        up(&port->sem);
+        mutex_unlock(&port->mutex);
         return 0;
 
 bailout_module_put:
         module_put(serial->type->driver.owner);
+bailout_mutex_unlock:
+        port->open_count = 0;
+        mutex_unlock(&port->mutex);
 bailout_kref_put:
         kref_put(&serial->kref, destroy_serial);
-        port->open_count = 0;
-        up(&port->sem);
         return retval;
 }
 
@@ -240,10 +245,10 @@ static void serial_close(struct tty_struct *tty, struct file * filp)
 
         dbg("%s - port %d", __FUNCTION__, port->number);
 
-        down(&port->sem);
+        mutex_lock(&port->mutex);
 
         if (port->open_count == 0) {
-                up(&port->sem);
+                mutex_unlock(&port->mutex);
                 return;
         }
 
@@ -262,7 +267,7 @@ static void serial_close(struct tty_struct *tty, struct file * filp)
                 module_put(port->serial->type->driver.owner);
         }
 
-        up(&port->sem);
+        mutex_unlock(&port->mutex);
         kref_put(&port->serial->kref, destroy_serial);
 }
 
@@ -783,7 +788,7 @@ int usb_serial_probe(struct usb_interface *interface,
                 port->number = i + serial->minor;
                 port->serial = serial;
                 spin_lock_init(&port->lock);
-                sema_init(&port->sem, 1);
+                mutex_init(&port->mutex);
                 INIT_WORK(&port->work, usb_serial_port_softint, port);
                 serial->port[i] = port;
         }
diff --git a/drivers/usb/serial/usb-serial.h b/drivers/usb/serial/usb-serial.h
index d7d27c3385b3..dc89d8710460 100644
--- a/drivers/usb/serial/usb-serial.h
+++ b/drivers/usb/serial/usb-serial.h
@@ -16,7 +16,7 @@
 
 #include <linux/config.h>
 #include <linux/kref.h>
-#include <asm/semaphore.h>
+#include <linux/mutex.h>
 
 #define SERIAL_TTY_MAJOR        188     /* Nice legal number now */
 #define SERIAL_TTY_MINORS       255     /* loads of devices :) */
@@ -31,7 +31,7 @@
  * @serial: pointer back to the struct usb_serial owner of this port.
  * @tty: pointer to the corresponding tty for this port.
  * @lock: spinlock to grab when updating portions of this structure.
- * @sem: semaphore used to synchronize serial_open() and serial_close()
+ * @mutex: mutex used to synchronize serial_open() and serial_close()
  *      access for this port.
  * @number: the number of the port (the minor number).
  * @interrupt_in_buffer: pointer to the interrupt in buffer for this port.
@@ -63,7 +63,7 @@ struct usb_serial_port {
         struct usb_serial *     serial;
         struct tty_struct *     tty;
         spinlock_t              lock;
-        struct semaphore        sem;
+        struct mutex            mutex;
         unsigned char           number;
 
         unsigned char *         interrupt_in_buffer;
diff --git a/drivers/usb/serial/whiteheat.c b/drivers/usb/serial/whiteheat.c
index 557411c6e7c7..f806553cd9a4 100644
--- a/drivers/usb/serial/whiteheat.c
+++ b/drivers/usb/serial/whiteheat.c
@@ -508,6 +508,7 @@ no_firmware:
         err("%s: Unable to retrieve firmware version, try replugging\n", serial->type->description);
         err("%s: If the firmware is not running (status led not blinking)\n", serial->type->description);
         err("%s: please contact support@connecttech.com\n", serial->type->description);
+        kfree(result);
         return -ENODEV;
 
 no_command_private: