USB: UHCI: add support for Intel's wakeup flags

This patch (as1396) adds code to uhci-hcd to support the
vendor-specific wakeup settings found in Intel's ICHx hardware.  A
couple of unnecessary memory barriers are removed.  And the root hub
isn't put back into the "suspended" state if power was lost during a
system sleep -- there's not much point in doing so because the root hub
will be resumed shortly.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 17 insertions, 13 deletions

diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c
index 9d4d81248f96..b04506036b64 100644
--- a/drivers/usb/host/uhci-hcd.c
+++ b/drivers/usb/host/uhci-hcd.c
@@ -176,6 +176,8 @@ static void check_and_reset_hc(struct uhci_hcd *uhci)
  */
 static void configure_hc(struct uhci_hcd *uhci)
 {
+        struct pci_dev *pdev = to_pci_dev(uhci_dev(uhci));
+
         /* Set the frame length to the default: 1 ms exactly */
         outb(USBSOF_DEFAULT, uhci->io_addr + USBSOF);
 
@@ -191,8 +193,11 @@ static void configure_hc(struct uhci_hcd *uhci)
         mb();
 
         /* Enable PIRQ */
-        pci_write_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP,
-                        USBLEGSUP_DEFAULT);
+        pci_write_config_word(pdev, USBLEGSUP, USBLEGSUP_DEFAULT);
+
+        /* Disable platform-specific non-PME# wakeup */
+        if (pdev->vendor == PCI_VENDOR_ID_INTEL)
+                pci_write_config_byte(pdev, USBRES_INTEL, 0);
 }
 
 
@@ -791,6 +796,7 @@ static int uhci_rh_resume(struct usb_hcd *hcd)
 static int uhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
 {
         struct uhci_hcd *uhci = hcd_to_uhci(hcd);
+        struct pci_dev *pdev = to_pci_dev(uhci_dev(uhci));
         int rc = 0;
 
         dev_dbg(uhci_dev(uhci), "%s\n", __func__);
@@ -808,11 +814,15 @@ static int uhci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup)
         /* All PCI host controllers are required to disable IRQ generation
          * at the source, so we must turn off PIRQ.
          */
-        pci_write_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP, 0);
-        mb();
+        pci_write_config_word(pdev, USBLEGSUP, 0);
         clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
 
-        /* FIXME: Enable non-PME# remote wakeup? */
+        /* Enable platform-specific non-PME# wakeup */
+        if (do_wakeup) {
+                if (pdev->vendor == PCI_VENDOR_ID_INTEL)
+                        pci_write_config_byte(pdev, USBRES_INTEL,
+                                        USBPORT1EN | USBPORT2EN);
+        }
 
 done_okay:
         clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
@@ -831,7 +841,6 @@ static int uhci_pci_resume(struct usb_hcd *hcd, bool hibernated)
          * even if the controller was dead.
          */
         set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
-        mb();
 
         spin_lock_irq(&uhci->lock);
 
@@ -839,8 +848,6 @@ static int uhci_pci_resume(struct usb_hcd *hcd, bool hibernated)
         if (hibernated)
                 uhci_hc_died(uhci);
 
-        /* FIXME: Disable non-PME# remote wakeup? */
-
         /* The firmware or a boot kernel may have changed the controller
          * settings during a system wakeup.  Check it and reconfigure
          * to avoid problems.
@@ -850,12 +857,9 @@ static int uhci_pci_resume(struct usb_hcd *hcd, bool hibernated)
         /* If the controller was dead before, it's back alive now */
         configure_hc(uhci);
 
-        if (uhci->rh_state == UHCI_RH_RESET) {
-
-                /* The controller had to be reset */
+        /* Tell the core if the controller had to be reset */
+        if (uhci->rh_state == UHCI_RH_RESET)
                 usb_root_hub_lost_power(hcd->self.root_hub);
-                suspend_rh(uhci, UHCI_RH_SUSPENDED);
-        }
 
         spin_unlock_irq(&uhci->lock);