Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 287 insertions, 0 deletions

diff --git a/drivers/scsi/sata_uli.c b/drivers/scsi/sata_uli.c
new file mode 100644
index 000000000000..0bff4f475f26
--- /dev/null
+++ b/drivers/scsi/sata_uli.c
@@ -0,0 +1,287 @@
+/*
+ *  sata_uli.c - ULi Electronics SATA
+ *
+ *  The contents of this file are subject to the Open
+ *  Software License version 1.1 that can be found at
+ *  http://www.opensource.org/licenses/osl-1.1.txt and is included herein
+ *  by reference.
+ *
+ *  Alternatively, the contents of this file may be used under the terms
+ *  of the GNU General Public License version 2 (the "GPL") as distributed
+ *  in the kernel source COPYING file, in which case the provisions of
+ *  the GPL are applicable instead of the above.  If you wish to allow
+ *  the use of your version of this file only under the terms of the
+ *  GPL and not to allow others to use your version of this file under
+ *  the OSL, indicate your decision by deleting the provisions above and
+ *  replace them with the notice and other provisions required by the GPL.
+ *  If you do not delete the provisions above, a recipient may use your
+ *  version of this file under either the OSL or the GPL.
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include "scsi.h"
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME        "sata_uli"
+#define DRV_VERSION     "0.5"
+
+enum {
+        uli_5289                = 0,
+        uli_5287                = 1,
+        uli_5281                = 2,
+
+        /* PCI configuration registers */
+        ULI5287_BASE            = 0x90, /* sata0 phy SCR registers */
+        ULI5287_OFFS            = 0x10, /* offset from sata0->sata1 phy regs */
+        ULI5281_BASE            = 0x60, /* sata0 phy SCR  registers */
+        ULI5281_OFFS            = 0x60, /* offset from sata0->sata1 phy regs */
+};
+
+static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg);
+static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+
+static struct pci_device_id uli_pci_tbl[] = {
+        { PCI_VENDOR_ID_AL, 0x5289, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5289 },
+        { PCI_VENDOR_ID_AL, 0x5287, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5287 },
+        { PCI_VENDOR_ID_AL, 0x5281, PCI_ANY_ID, PCI_ANY_ID, 0, 0, uli_5281 },
+        { }     /* terminate list */
+};
+
+
+static struct pci_driver uli_pci_driver = {
+        .name                   = DRV_NAME,
+        .id_table               = uli_pci_tbl,
+        .probe                  = uli_init_one,
+        .remove                 = ata_pci_remove_one,
+};
+
+static Scsi_Host_Template uli_sht = {
+        .module                 = THIS_MODULE,
+        .name                   = DRV_NAME,
+        .ioctl                  = ata_scsi_ioctl,
+        .queuecommand           = ata_scsi_queuecmd,
+        .eh_strategy_handler    = ata_scsi_error,
+        .can_queue              = ATA_DEF_QUEUE,
+        .this_id                = ATA_SHT_THIS_ID,
+        .sg_tablesize           = LIBATA_MAX_PRD,
+        .max_sectors            = ATA_MAX_SECTORS,
+        .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
+        .emulated               = ATA_SHT_EMULATED,
+        .use_clustering         = ATA_SHT_USE_CLUSTERING,
+        .proc_name              = DRV_NAME,
+        .dma_boundary           = ATA_DMA_BOUNDARY,
+        .slave_configure        = ata_scsi_slave_config,
+        .bios_param             = ata_std_bios_param,
+        .ordered_flush          = 1,
+};
+
+static struct ata_port_operations uli_ops = {
+        .port_disable           = ata_port_disable,
+
+        .tf_load                = ata_tf_load,
+        .tf_read                = ata_tf_read,
+        .check_status           = ata_check_status,
+        .exec_command           = ata_exec_command,
+        .dev_select             = ata_std_dev_select,
+
+        .phy_reset              = sata_phy_reset,
+
+        .bmdma_setup            = ata_bmdma_setup,
+        .bmdma_start            = ata_bmdma_start,
+        .bmdma_stop             = ata_bmdma_stop,
+        .bmdma_status           = ata_bmdma_status,
+        .qc_prep                = ata_qc_prep,
+        .qc_issue               = ata_qc_issue_prot,
+
+        .eng_timeout            = ata_eng_timeout,
+
+        .irq_handler            = ata_interrupt,
+        .irq_clear              = ata_bmdma_irq_clear,
+
+        .scr_read               = uli_scr_read,
+        .scr_write              = uli_scr_write,
+
+        .port_start             = ata_port_start,
+        .port_stop              = ata_port_stop,
+};
+
+static struct ata_port_info uli_port_info = {
+        .sht            = &uli_sht,
+        .host_flags     = ATA_FLAG_SATA | ATA_FLAG_SATA_RESET |
+                          ATA_FLAG_NO_LEGACY,
+        .pio_mask       = 0x03,         //support pio mode 4 (FIXME)
+        .udma_mask      = 0x7f,         //support udma mode 6
+        .port_ops       = &uli_ops,
+};
+
+
+MODULE_AUTHOR("Peer Chen");
+MODULE_DESCRIPTION("low-level driver for ULi Electronics SATA controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, uli_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+static unsigned int get_scr_cfg_addr(struct ata_port *ap, unsigned int sc_reg)
+{
+        return ap->ioaddr.scr_addr + (4 * sc_reg);
+}
+
+static u32 uli_scr_cfg_read (struct ata_port *ap, unsigned int sc_reg)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        unsigned int cfg_addr = get_scr_cfg_addr(ap, sc_reg);
+        u32 val;
+
+        pci_read_config_dword(pdev, cfg_addr, &val);
+        return val;
+}
+
+static void uli_scr_cfg_write (struct ata_port *ap, unsigned int scr, u32 val)
+{
+        struct pci_dev *pdev = to_pci_dev(ap->host_set->dev);
+        unsigned int cfg_addr = get_scr_cfg_addr(ap, scr);
+
+        pci_write_config_dword(pdev, cfg_addr, val);
+}
+
+static u32 uli_scr_read (struct ata_port *ap, unsigned int sc_reg)
+{
+        if (sc_reg > SCR_CONTROL)
+                return 0xffffffffU;
+
+        return uli_scr_cfg_read(ap, sc_reg);
+}
+
+static void uli_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+{
+        if (sc_reg > SCR_CONTROL)       //SCR_CONTROL=2, SCR_ERROR=1, SCR_STATUS=0
+                return;
+
+        uli_scr_cfg_write(ap, sc_reg, val);
+}
+
+/* move to PCI layer, integrate w/ MSI stuff */
+static void pci_enable_intx(struct pci_dev *pdev)
+{
+        u16 pci_command;
+
+        pci_read_config_word(pdev, PCI_COMMAND, &pci_command);
+        if (pci_command & PCI_COMMAND_INTX_DISABLE) {
+                pci_command &= ~PCI_COMMAND_INTX_DISABLE;
+                pci_write_config_word(pdev, PCI_COMMAND, pci_command);
+        }
+}
+
+static int uli_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+        struct ata_probe_ent *probe_ent;
+        struct ata_port_info *ppi;
+        int rc;
+        unsigned int board_idx = (unsigned int) ent->driver_data;
+        int pci_dev_busy = 0;
+
+        rc = pci_enable_device(pdev);
+        if (rc)
+                return rc;
+
+        rc = pci_request_regions(pdev, DRV_NAME);
+        if (rc) {
+                pci_dev_busy = 1;
+                goto err_out;
+        }
+
+        rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+        if (rc)
+                goto err_out_regions;
+        rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+        if (rc)
+                goto err_out_regions;
+
+        ppi = &uli_port_info;
+        probe_ent = ata_pci_init_native_mode(pdev, &ppi);
+        if (!probe_ent) {
+                rc = -ENOMEM;
+                goto err_out_regions;
+        }
+        
+        switch (board_idx) {
+        case uli_5287:
+                probe_ent->port[0].scr_addr = ULI5287_BASE;
+                probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
+                probe_ent->n_ports = 4;
+
+                probe_ent->port[2].cmd_addr = pci_resource_start(pdev, 0) + 8;
+                probe_ent->port[2].altstatus_addr =
+                probe_ent->port[2].ctl_addr =
+                        (pci_resource_start(pdev, 1) | ATA_PCI_CTL_OFS) + 4;
+                probe_ent->port[2].bmdma_addr = pci_resource_start(pdev, 4) + 16;
+                probe_ent->port[2].scr_addr = ULI5287_BASE + ULI5287_OFFS*4;
+
+                probe_ent->port[3].cmd_addr = pci_resource_start(pdev, 2) + 8;
+                probe_ent->port[3].altstatus_addr =
+                probe_ent->port[3].ctl_addr =
+                        (pci_resource_start(pdev, 3) | ATA_PCI_CTL_OFS) + 4;
+                probe_ent->port[3].bmdma_addr = pci_resource_start(pdev, 4) + 24;
+                probe_ent->port[3].scr_addr = ULI5287_BASE + ULI5287_OFFS*5;
+
+                ata_std_ports(&probe_ent->port[2]);
+                ata_std_ports(&probe_ent->port[3]);
+                break;
+
+        case uli_5289:
+                probe_ent->port[0].scr_addr = ULI5287_BASE;
+                probe_ent->port[1].scr_addr = ULI5287_BASE + ULI5287_OFFS;
+                break;
+
+        case uli_5281:
+                probe_ent->port[0].scr_addr = ULI5281_BASE;
+                probe_ent->port[1].scr_addr = ULI5281_BASE + ULI5281_OFFS;
+                break;
+
+        default:
+                BUG();
+                break;
+        }
+
+        pci_set_master(pdev);
+        pci_enable_intx(pdev);
+
+        /* FIXME: check ata_device_add return value */
+        ata_device_add(probe_ent);
+        kfree(probe_ent);
+
+        return 0;
+
+err_out_regions:
+        pci_release_regions(pdev);
+
+err_out:
+        if (!pci_dev_busy)
+                pci_disable_device(pdev);
+        return rc;
+
+}
+
+static int __init uli_init(void)
+{
+        return pci_module_init(&uli_pci_driver);
+}
+
+static void __exit uli_exit(void)
+{
+        pci_unregister_driver(&uli_pci_driver);
+}
+
+
+module_init(uli_init);
+module_exit(uli_exit);