Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 508 insertions, 0 deletions

diff --git a/drivers/scsi/qlogicpti.h b/drivers/scsi/qlogicpti.h
new file mode 100644
index 000000000000..6cd1c0771d29
--- /dev/null
+++ b/drivers/scsi/qlogicpti.h
@@ -0,0 +1,508 @@
+/* qlogicpti.h: Performance Technologies QlogicISP sbus card defines.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@caipfs.rutgers.edu)
+ */
+
+#ifndef _QLOGICPTI_H
+#define _QLOGICPTI_H
+
+/* Qlogic/SBUS controller registers. */
+#define SBUS_CFG1       0x006UL
+#define SBUS_CTRL       0x008UL
+#define SBUS_STAT       0x00aUL
+#define SBUS_SEMAPHORE  0x00cUL
+#define CMD_DMA_CTRL    0x022UL
+#define DATA_DMA_CTRL   0x042UL
+#define MBOX0           0x080UL
+#define MBOX1           0x082UL
+#define MBOX2           0x084UL
+#define MBOX3           0x086UL
+#define MBOX4           0x088UL
+#define MBOX5           0x08aUL
+#define CPU_CMD         0x214UL
+#define CPU_ORIDE       0x224UL
+#define CPU_PCTRL       0x272UL
+#define CPU_PDIFF       0x276UL
+#define RISC_PSR        0x420UL
+#define RISC_MTREG      0x42EUL
+#define HCCTRL          0x440UL
+
+/* SCSI parameters for this driver. */
+#define MAX_TARGETS     16
+#define MAX_LUNS        8
+
+/* With the qlogic interface, every queue slot can hold a SCSI
+ * command with up to 4 scatter/gather entries.  If we need more
+ * than 4 entries, continuation entries can be used that hold
+ * another 7 entries each.  Unlike for other drivers, this means
+ * that the maximum number of scatter/gather entries we can
+ * support at any given time is a function of the number of queue
+ * slots available.  That is, host->can_queue and host->sg_tablesize
+ * are dynamic and _not_ independent.  This all works fine because
+ * requests are queued serially and the scatter/gather limit is
+ * determined for each queue request anew.
+ */
+#define QLOGICPTI_REQ_QUEUE_LEN 255     /* must be power of two - 1 */
+#define QLOGICPTI_MAX_SG(ql)    (4 + ((ql) > 0) ? 7*((ql) - 1) : 0)
+
+/* mailbox command complete status codes */
+#define MBOX_COMMAND_COMPLETE           0x4000
+#define INVALID_COMMAND                 0x4001
+#define HOST_INTERFACE_ERROR            0x4002
+#define TEST_FAILED                     0x4003
+#define COMMAND_ERROR                   0x4005
+#define COMMAND_PARAM_ERROR             0x4006
+
+/* async event status codes */
+#define ASYNC_SCSI_BUS_RESET            0x8001
+#define SYSTEM_ERROR                    0x8002
+#define REQUEST_TRANSFER_ERROR          0x8003
+#define RESPONSE_TRANSFER_ERROR         0x8004
+#define REQUEST_QUEUE_WAKEUP            0x8005
+#define EXECUTION_TIMEOUT_RESET         0x8006
+
+/* Am I fucking pedantic or what? */
+struct Entry_header {
+#ifdef __BIG_ENDIAN
+        u8      entry_cnt;
+        u8      entry_type;
+        u8      flags;
+        u8      sys_def_1;
+#else /* __LITTLE_ENDIAN */
+        u8      entry_type;
+        u8      entry_cnt;
+        u8      sys_def_1;
+        u8      flags;
+#endif
+};
+
+/* entry header type commands */
+#define ENTRY_COMMAND           1
+#define ENTRY_CONTINUATION      2
+#define ENTRY_STATUS            3
+#define ENTRY_MARKER            4
+#define ENTRY_EXTENDED_COMMAND  5
+
+/* entry header flag definitions */
+#define EFLAG_CONTINUATION      1
+#define EFLAG_BUSY              2
+#define EFLAG_BAD_HEADER        4
+#define EFLAG_BAD_PAYLOAD       8
+
+struct dataseg {
+        u32     d_base;
+        u32     d_count;
+};
+
+struct Command_Entry {
+        struct Entry_header     hdr;
+        u32                     handle;
+#ifdef __BIG_ENDIAN
+        u8                      target_id;
+        u8                      target_lun;
+#else /* __LITTLE_ENDIAN */
+        u8                      target_lun;
+        u8                      target_id;
+#endif
+        u16                     cdb_length;
+        u16                     control_flags;
+        u16                     rsvd;
+        u16                     time_out;
+        u16                     segment_cnt;
+        u8                      cdb[12];
+        struct dataseg          dataseg[4];
+};
+
+/* command entry control flag definitions */
+#define CFLAG_NODISC            0x01
+#define CFLAG_HEAD_TAG          0x02
+#define CFLAG_ORDERED_TAG       0x04
+#define CFLAG_SIMPLE_TAG        0x08
+#define CFLAG_TAR_RTN           0x10
+#define CFLAG_READ              0x20
+#define CFLAG_WRITE             0x40
+
+struct Ext_Command_Entry {
+        struct Entry_header     hdr;
+        u32                     handle;
+#ifdef __BIG_ENDIAN
+        u8                      target_id;
+        u8                      target_lun;
+#else /* __LITTLE_ENDIAN */
+        u8                      target_lun;
+        u8                      target_id;
+#endif
+        u16                     cdb_length;
+        u16                     control_flags;
+        u16                     rsvd;
+        u16                     time_out;
+        u16                     segment_cnt;
+        u8                      cdb[44];
+};
+
+struct Continuation_Entry {
+        struct Entry_header     hdr;
+        u32                     reserved;
+        struct dataseg          dataseg[7];
+};
+
+struct Marker_Entry {
+        struct Entry_header     hdr;
+        u32                     reserved;
+#ifdef __BIG_ENDIAN
+        u8                      target_id;
+        u8                      target_lun;
+#else /* __LITTLE_ENDIAN */
+        u8                      target_lun;
+        u8                      target_id;
+#endif
+#ifdef __BIG_ENDIAN
+        u8                      rsvd;
+        u8                      modifier;
+#else /* __LITTLE_ENDIAN */
+        u8                      modifier;
+        u8                      rsvd;
+#endif
+        u8                      rsvds[52];
+};
+
+/* marker entry modifier definitions */
+#define SYNC_DEVICE     0
+#define SYNC_TARGET     1
+#define SYNC_ALL        2
+
+struct Status_Entry {
+        struct Entry_header     hdr;
+        u32                     handle;
+        u16                     scsi_status;
+        u16                     completion_status;
+        u16                     state_flags;
+        u16                     status_flags;
+        u16                     time;
+        u16                     req_sense_len;
+        u32                     residual;
+        u8                      rsvd[8];
+        u8                      req_sense_data[32];
+};
+
+/* status entry completion status definitions */
+#define CS_COMPLETE                     0x0000
+#define CS_INCOMPLETE                   0x0001
+#define CS_DMA_ERROR                    0x0002
+#define CS_TRANSPORT_ERROR              0x0003
+#define CS_RESET_OCCURRED               0x0004
+#define CS_ABORTED                      0x0005
+#define CS_TIMEOUT                      0x0006
+#define CS_DATA_OVERRUN                 0x0007
+#define CS_COMMAND_OVERRUN              0x0008
+#define CS_STATUS_OVERRUN               0x0009
+#define CS_BAD_MESSAGE                  0x000a
+#define CS_NO_MESSAGE_OUT               0x000b
+#define CS_EXT_ID_FAILED                0x000c
+#define CS_IDE_MSG_FAILED               0x000d
+#define CS_ABORT_MSG_FAILED             0x000e
+#define CS_REJECT_MSG_FAILED            0x000f
+#define CS_NOP_MSG_FAILED               0x0010
+#define CS_PARITY_ERROR_MSG_FAILED      0x0011
+#define CS_DEVICE_RESET_MSG_FAILED      0x0012
+#define CS_ID_MSG_FAILED                0x0013
+#define CS_UNEXP_BUS_FREE               0x0014
+#define CS_DATA_UNDERRUN                0x0015
+#define CS_BUS_RESET                    0x001c
+
+/* status entry state flag definitions */
+#define SF_GOT_BUS                      0x0100
+#define SF_GOT_TARGET                   0x0200
+#define SF_SENT_CDB                     0x0400
+#define SF_TRANSFERRED_DATA             0x0800
+#define SF_GOT_STATUS                   0x1000
+#define SF_GOT_SENSE                    0x2000
+
+/* status entry status flag definitions */
+#define STF_DISCONNECT                  0x0001
+#define STF_SYNCHRONOUS                 0x0002
+#define STF_PARITY_ERROR                0x0004
+#define STF_BUS_RESET                   0x0008
+#define STF_DEVICE_RESET                0x0010
+#define STF_ABORTED                     0x0020
+#define STF_TIMEOUT                     0x0040
+#define STF_NEGOTIATION                 0x0080
+
+/* mailbox commands */
+#define MBOX_NO_OP                      0x0000
+#define MBOX_LOAD_RAM                   0x0001
+#define MBOX_EXEC_FIRMWARE              0x0002
+#define MBOX_DUMP_RAM                   0x0003
+#define MBOX_WRITE_RAM_WORD             0x0004
+#define MBOX_READ_RAM_WORD              0x0005
+#define MBOX_MAILBOX_REG_TEST           0x0006
+#define MBOX_VERIFY_CHECKSUM            0x0007
+#define MBOX_ABOUT_FIRMWARE             0x0008
+#define MBOX_CHECK_FIRMWARE             0x000e
+#define MBOX_INIT_REQ_QUEUE             0x0010
+#define MBOX_INIT_RES_QUEUE             0x0011
+#define MBOX_EXECUTE_IOCB               0x0012
+#define MBOX_WAKE_UP                    0x0013
+#define MBOX_STOP_FIRMWARE              0x0014
+#define MBOX_ABORT                      0x0015
+#define MBOX_ABORT_DEVICE               0x0016
+#define MBOX_ABORT_TARGET               0x0017
+#define MBOX_BUS_RESET                  0x0018
+#define MBOX_STOP_QUEUE                 0x0019
+#define MBOX_START_QUEUE                0x001a
+#define MBOX_SINGLE_STEP_QUEUE          0x001b
+#define MBOX_ABORT_QUEUE                0x001c
+#define MBOX_GET_DEV_QUEUE_STATUS       0x001d
+#define MBOX_GET_FIRMWARE_STATUS        0x001f
+#define MBOX_GET_INIT_SCSI_ID           0x0020
+#define MBOX_GET_SELECT_TIMEOUT         0x0021
+#define MBOX_GET_RETRY_COUNT            0x0022
+#define MBOX_GET_TAG_AGE_LIMIT          0x0023
+#define MBOX_GET_CLOCK_RATE             0x0024
+#define MBOX_GET_ACT_NEG_STATE          0x0025
+#define MBOX_GET_ASYNC_DATA_SETUP_TIME  0x0026
+#define MBOX_GET_SBUS_PARAMS            0x0027
+#define MBOX_GET_TARGET_PARAMS          0x0028
+#define MBOX_GET_DEV_QUEUE_PARAMS       0x0029
+#define MBOX_SET_INIT_SCSI_ID           0x0030
+#define MBOX_SET_SELECT_TIMEOUT         0x0031
+#define MBOX_SET_RETRY_COUNT            0x0032
+#define MBOX_SET_TAG_AGE_LIMIT          0x0033
+#define MBOX_SET_CLOCK_RATE             0x0034
+#define MBOX_SET_ACTIVE_NEG_STATE       0x0035
+#define MBOX_SET_ASYNC_DATA_SETUP_TIME  0x0036
+#define MBOX_SET_SBUS_CONTROL_PARAMS    0x0037
+#define MBOX_SET_TARGET_PARAMS          0x0038
+#define MBOX_SET_DEV_QUEUE_PARAMS       0x0039
+
+struct host_param {
+        u_short         initiator_scsi_id;
+        u_short         bus_reset_delay;
+        u_short         retry_count;
+        u_short         retry_delay;
+        u_short         async_data_setup_time;
+        u_short         req_ack_active_negation;
+        u_short         data_line_active_negation;
+        u_short         data_dma_burst_enable;
+        u_short         command_dma_burst_enable;
+        u_short         tag_aging;
+        u_short         selection_timeout;
+        u_short         max_queue_depth;
+};
+
+/*
+ * Device Flags:
+ *
+ * Bit  Name
+ * ---------
+ *  7   Disconnect Privilege
+ *  6   Parity Checking
+ *  5   Wide Data Transfers
+ *  4   Synchronous Data Transfers
+ *  3   Tagged Queuing
+ *  2   Automatic Request Sense
+ *  1   Stop Queue on Check Condition
+ *  0   Renegotiate on Error
+ */
+
+struct dev_param {
+        u_short         device_flags;
+        u_short         execution_throttle;
+        u_short         synchronous_period;
+        u_short         synchronous_offset;
+        u_short         device_enable;
+        u_short         reserved; /* pad */
+};
+
+/*
+ * The result queue can be quite a bit smaller since continuation entries
+ * do not show up there:
+ */
+#define RES_QUEUE_LEN           255     /* Must be power of two - 1 */
+#define QUEUE_ENTRY_LEN         64
+
+#define NEXT_REQ_PTR(wheee)   (((wheee) + 1) & QLOGICPTI_REQ_QUEUE_LEN)
+#define NEXT_RES_PTR(wheee)   (((wheee) + 1) & RES_QUEUE_LEN)
+#define PREV_REQ_PTR(wheee)   (((wheee) - 1) & QLOGICPTI_REQ_QUEUE_LEN)
+#define PREV_RES_PTR(wheee)   (((wheee) - 1) & RES_QUEUE_LEN)
+
+struct pti_queue_entry {
+        char __opaque[QUEUE_ENTRY_LEN];
+};
+
+struct scsi_cmnd;
+
+/* Software state for the driver. */
+struct qlogicpti {
+        /* These are the hot elements in the cache, so they come first. */
+        void __iomem             *qregs;                /* Adapter registers          */
+        struct pti_queue_entry   *res_cpu;              /* Ptr to RESPONSE bufs (CPU) */
+        struct pti_queue_entry   *req_cpu;              /* Ptr to REQUEST bufs (CPU)  */
+
+        u_int                     req_in_ptr;           /* index of next request slot */
+        u_int                     res_out_ptr;          /* index of next result slot  */
+        long                      send_marker;          /* must we send a marker?     */
+        struct sbus_dev          *sdev;
+        unsigned long             __pad;
+
+        int                       cmd_count[MAX_TARGETS];
+        unsigned long             tag_ages[MAX_TARGETS];
+
+        /* The cmd->handler is only 32-bits, so that things work even on monster
+         * Ex000 sparc64 machines with >4GB of ram we just keep track of the
+         * scsi command pointers here.  This is essentially what Matt Jacob does. -DaveM
+         */
+        struct scsi_cmnd         *cmd_slots[QLOGICPTI_REQ_QUEUE_LEN + 1];
+
+        /* The rest of the elements are unimportant for performance. */
+        struct qlogicpti         *next;
+        __u32                     res_dvma;             /* Ptr to RESPONSE bufs (DVMA)*/
+        __u32                     req_dvma;             /* Ptr to REQUEST bufs (DVMA) */
+        u_char                    fware_majrev, fware_minrev, fware_micrev;
+        struct Scsi_Host         *qhost;
+        int                       qpti_id;
+        int                       scsi_id;
+        int                       prom_node;
+        char                      prom_name[64];
+        int                       irq;
+        char                      differential, ultra, clock;
+        unsigned char             bursts;
+        struct  host_param        host_param;
+        struct  dev_param         dev_param[MAX_TARGETS];
+
+        void __iomem              *sreg;
+#define SREG_TPOWER               0x80   /* State of termpwr           */
+#define SREG_FUSE                 0x40   /* State of on board fuse     */
+#define SREG_PDISAB               0x20   /* Disable state for power on */
+#define SREG_DSENSE               0x10   /* Sense for differential     */
+#define SREG_IMASK                0x0c   /* Interrupt level            */
+#define SREG_SPMASK               0x03   /* Mask for switch pack       */
+        unsigned char             swsreg;
+        unsigned int    
+                gotirq  :       1,      /* this instance got an irq */
+                is_pti  :       1,      /* Non-zero if this is a PTI board. */
+                sbits   :       16;     /* syncmode known bits */
+};
+
+/* How to twiddle them bits... */
+
+/* SBUS config register one. */
+#define SBUS_CFG1_EPAR          0x0100      /* Enable parity checking           */
+#define SBUS_CFG1_FMASK         0x00f0      /* Forth code cycle mask            */
+#define SBUS_CFG1_BENAB         0x0004      /* Burst dvma enable                */
+#define SBUS_CFG1_B64           0x0003      /* Enable 64byte bursts             */
+#define SBUS_CFG1_B32           0x0002      /* Enable 32byte bursts             */
+#define SBUS_CFG1_B16           0x0001      /* Enable 16byte bursts             */
+#define SBUS_CFG1_B8            0x0008      /* Enable 8byte bursts              */
+
+/* SBUS control register */
+#define SBUS_CTRL_EDIRQ         0x0020      /* Enable Data DVMA Interrupts      */
+#define SBUS_CTRL_ECIRQ         0x0010      /* Enable Command DVMA Interrupts   */
+#define SBUS_CTRL_ESIRQ         0x0008      /* Enable SCSI Processor Interrupts */
+#define SBUS_CTRL_ERIRQ         0x0004      /* Enable RISC Processor Interrupts */
+#define SBUS_CTRL_GENAB         0x0002      /* Global Interrupt Enable          */
+#define SBUS_CTRL_RESET         0x0001      /* Soft Reset                       */
+
+/* SBUS status register */
+#define SBUS_STAT_DINT          0x0020      /* Data DVMA IRQ pending            */
+#define SBUS_STAT_CINT          0x0010      /* Command DVMA IRQ pending         */
+#define SBUS_STAT_SINT          0x0008      /* SCSI Processor IRQ pending       */
+#define SBUS_STAT_RINT          0x0004      /* RISC Processor IRQ pending       */
+#define SBUS_STAT_GINT          0x0002      /* Global IRQ pending               */
+
+/* SBUS semaphore register */
+#define SBUS_SEMAPHORE_STAT     0x0002      /* Semaphore status bit             */
+#define SBUS_SEMAPHORE_LCK      0x0001      /* Semaphore lock bit               */
+
+/* DVMA control register */
+#define DMA_CTRL_CSUSPEND       0x0010      /* DMA channel suspend              */
+#define DMA_CTRL_CCLEAR         0x0008      /* DMA channel clear and reset      */
+#define DMA_CTRL_FCLEAR         0x0004      /* DMA fifo clear                   */
+#define DMA_CTRL_CIRQ           0x0002      /* DMA irq clear                    */
+#define DMA_CTRL_DMASTART       0x0001      /* DMA transfer start               */
+
+/* SCSI processor override register */
+#define CPU_ORIDE_ETRIG         0x8000      /* External trigger enable          */
+#define CPU_ORIDE_STEP          0x4000      /* Single step mode enable          */
+#define CPU_ORIDE_BKPT          0x2000      /* Breakpoint reg enable            */
+#define CPU_ORIDE_PWRITE        0x1000      /* SCSI pin write enable            */
+#define CPU_ORIDE_OFORCE        0x0800      /* Force outputs on                 */
+#define CPU_ORIDE_LBACK         0x0400      /* SCSI loopback enable             */
+#define CPU_ORIDE_PTEST         0x0200      /* Parity test enable               */
+#define CPU_ORIDE_TENAB         0x0100      /* SCSI pins tristate enable        */
+#define CPU_ORIDE_TPINS         0x0080      /* SCSI pins enable                 */
+#define CPU_ORIDE_FRESET        0x0008      /* FIFO reset                       */
+#define CPU_ORIDE_CTERM         0x0004      /* Command terminate                */
+#define CPU_ORIDE_RREG          0x0002      /* Reset SCSI processor regs        */
+#define CPU_ORIDE_RMOD          0x0001      /* Reset SCSI processor module      */
+
+/* SCSI processor commands */
+#define CPU_CMD_BRESET          0x300b      /* Reset SCSI bus                   */
+
+/* SCSI processor pin control register */
+#define CPU_PCTRL_PVALID        0x8000      /* Phase bits are valid             */
+#define CPU_PCTRL_PHI           0x0400      /* Parity bit high                  */
+#define CPU_PCTRL_PLO           0x0200      /* Parity bit low                   */
+#define CPU_PCTRL_REQ           0x0100      /* REQ bus signal                   */
+#define CPU_PCTRL_ACK           0x0080      /* ACK bus signal                   */
+#define CPU_PCTRL_RST           0x0040      /* RST bus signal                   */
+#define CPU_PCTRL_BSY           0x0020      /* BSY bus signal                   */
+#define CPU_PCTRL_SEL           0x0010      /* SEL bus signal                   */
+#define CPU_PCTRL_ATN           0x0008      /* ATN bus signal                   */
+#define CPU_PCTRL_MSG           0x0004      /* MSG bus signal                   */
+#define CPU_PCTRL_CD            0x0002      /* CD bus signal                    */
+#define CPU_PCTRL_IO            0x0001      /* IO bus signal                    */
+
+/* SCSI processor differential pins register */
+#define CPU_PDIFF_SENSE         0x0200      /* Differential sense               */
+#define CPU_PDIFF_MODE          0x0100      /* Differential mode                */
+#define CPU_PDIFF_OENAB         0x0080      /* Outputs enable                   */
+#define CPU_PDIFF_PMASK         0x007c      /* Differential control pins        */
+#define CPU_PDIFF_TGT           0x0002      /* Target mode enable               */
+#define CPU_PDIFF_INIT          0x0001      /* Initiator mode enable            */
+
+/* RISC processor status register */
+#define RISC_PSR_FTRUE          0x8000      /* Force true                       */
+#define RISC_PSR_LCD            0x4000      /* Loop counter shows done status   */
+#define RISC_PSR_RIRQ           0x2000      /* RISC irq status                  */
+#define RISC_PSR_TOFLOW         0x1000      /* Timer overflow (rollover)        */
+#define RISC_PSR_AOFLOW         0x0800      /* Arithmetic overflow              */
+#define RISC_PSR_AMSB           0x0400      /* Arithmetic big endian            */
+#define RISC_PSR_ACARRY         0x0200      /* Arithmetic carry                 */
+#define RISC_PSR_AZERO          0x0100      /* Arithmetic zero                  */
+#define RISC_PSR_ULTRA          0x0020      /* Ultra mode                       */
+#define RISC_PSR_DIRQ           0x0010      /* DVMA interrupt                   */
+#define RISC_PSR_SIRQ           0x0008      /* SCSI processor interrupt         */
+#define RISC_PSR_HIRQ           0x0004      /* Host interrupt                   */
+#define RISC_PSR_IPEND          0x0002      /* Interrupt pending                */
+#define RISC_PSR_FFALSE         0x0001      /* Force false                      */
+
+/* RISC processor memory timing register */
+#define RISC_MTREG_P1DFLT       0x1200      /* Default read/write timing, pg1   */
+#define RISC_MTREG_P0DFLT       0x0012      /* Default read/write timing, pg0   */
+#define RISC_MTREG_P1ULTRA      0x2300      /* Ultra-mode rw timing, pg1        */
+#define RISC_MTREG_P0ULTRA      0x0023      /* Ultra-mode rw timing, pg0        */
+
+/* Host command/ctrl register */
+#define HCCTRL_NOP              0x0000      /* CMD: No operation                */
+#define HCCTRL_RESET            0x1000      /* CMD: Reset RISC cpu              */
+#define HCCTRL_PAUSE            0x2000      /* CMD: Pause RISC cpu              */
+#define HCCTRL_REL              0x3000      /* CMD: Release paused RISC cpu     */
+#define HCCTRL_STEP             0x4000      /* CMD: Single step RISC cpu        */
+#define HCCTRL_SHIRQ            0x5000      /* CMD: Set host irq                */
+#define HCCTRL_CHIRQ            0x6000      /* CMD: Clear host irq              */
+#define HCCTRL_CRIRQ            0x7000      /* CMD: Clear RISC cpu irq          */
+#define HCCTRL_BKPT             0x8000      /* CMD: Breakpoint enables change   */
+#define HCCTRL_TMODE            0xf000      /* CMD: Enable test mode            */
+#define HCCTRL_HIRQ             0x0080      /* Host IRQ pending                 */
+#define HCCTRL_RRIP             0x0040      /* RISC cpu reset in happening now  */
+#define HCCTRL_RPAUSED          0x0020      /* RISC cpu is paused now           */
+#define HCCTRL_EBENAB           0x0010      /* External breakpoint enable       */
+#define HCCTRL_B1ENAB           0x0008      /* Breakpoint 1 enable              */
+#define HCCTRL_B0ENAB           0x0004      /* Breakpoint 0 enable              */
+
+/* For our interrupt engine. */
+#define for_each_qlogicpti(qp) \
+        for((qp) = qptichain; (qp); (qp) = (qp)->next)
+
+#endif /* !(_QLOGICPTI_H) */