Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 127 insertions, 0 deletions

diff --git a/drivers/scsi/mesh.h b/drivers/scsi/mesh.h
new file mode 100644
index 000000000000..4fdb81fa55e2
--- /dev/null
+++ b/drivers/scsi/mesh.h
@@ -0,0 +1,127 @@
+/*
+ * mesh.h: definitions for the driver for the MESH SCSI bus adaptor
+ * (Macintosh Enhanced SCSI Hardware) found on Power Macintosh computers.
+ *
+ * Copyright (C) 1996 Paul Mackerras.
+ */
+#ifndef _MESH_H
+#define _MESH_H
+
+/*
+ * Registers in the MESH controller.
+ */
+
+struct mesh_regs {
+        unsigned char   count_lo;
+        char pad0[15];
+        unsigned char   count_hi;
+        char pad1[15];
+        unsigned char   fifo;
+        char pad2[15];
+        unsigned char   sequence;
+        char pad3[15];
+        unsigned char   bus_status0;
+        char pad4[15];
+        unsigned char   bus_status1;
+        char pad5[15];
+        unsigned char   fifo_count;
+        char pad6[15];
+        unsigned char   exception;
+        char pad7[15];
+        unsigned char   error;
+        char pad8[15];
+        unsigned char   intr_mask;
+        char pad9[15];
+        unsigned char   interrupt;
+        char pad10[15];
+        unsigned char   source_id;
+        char pad11[15];
+        unsigned char   dest_id;
+        char pad12[15];
+        unsigned char   sync_params;
+        char pad13[15];
+        unsigned char   mesh_id;
+        char pad14[15];
+        unsigned char   sel_timeout;
+        char pad15[15];
+};
+
+/* Bits in the sequence register. */
+#define SEQ_DMA_MODE    0x80    /* use DMA for data transfer */
+#define SEQ_TARGET      0x40    /* put the controller into target mode */
+#define SEQ_ATN         0x20    /* assert ATN signal */
+#define SEQ_ACTIVE_NEG  0x10    /* use active negation on REQ/ACK */
+#define SEQ_CMD         0x0f    /* command bits: */
+#define SEQ_ARBITRATE   1       /*  get the bus */
+#define SEQ_SELECT      2       /*  select a target */
+#define SEQ_COMMAND     3       /*  send a command */
+#define SEQ_STATUS      4       /*  receive status */
+#define SEQ_DATAOUT     5       /*  send data */
+#define SEQ_DATAIN      6       /*  receive data */
+#define SEQ_MSGOUT      7       /*  send a message */
+#define SEQ_MSGIN       8       /*  receive a message */
+#define SEQ_BUSFREE     9       /*  look for bus free */
+#define SEQ_ENBPARITY   0x0a    /*  enable parity checking */
+#define SEQ_DISPARITY   0x0b    /*  disable parity checking */
+#define SEQ_ENBRESEL    0x0c    /*  enable reselection */
+#define SEQ_DISRESEL    0x0d    /*  disable reselection */
+#define SEQ_RESETMESH   0x0e    /*  reset the controller */
+#define SEQ_FLUSHFIFO   0x0f    /*  clear out the FIFO */
+
+/* Bits in the bus_status0 and bus_status1 registers:
+   these correspond directly to the SCSI bus control signals. */
+#define BS0_REQ         0x20
+#define BS0_ACK         0x10
+#define BS0_ATN         0x08
+#define BS0_MSG         0x04
+#define BS0_CD          0x02
+#define BS0_IO          0x01
+#define BS1_RST         0x80
+#define BS1_BSY         0x40
+#define BS1_SEL         0x20
+
+/* Bus phases defined by the bits in bus_status0 */
+#define BS0_PHASE       (BS0_MSG+BS0_CD+BS0_IO)
+#define BP_DATAOUT      0
+#define BP_DATAIN       BS0_IO
+#define BP_COMMAND      BS0_CD
+#define BP_STATUS       (BS0_CD+BS0_IO)
+#define BP_MSGOUT       (BS0_MSG+BS0_CD)
+#define BP_MSGIN        (BS0_MSG+BS0_CD+BS0_IO)
+
+/* Bits in the exception register. */
+#define EXC_SELWATN     0x20    /* (as target) we were selected with ATN */
+#define EXC_SELECTED    0x10    /* (as target) we were selected w/o ATN */
+#define EXC_RESELECTED  0x08    /* (as initiator) we were reselected */
+#define EXC_ARBLOST     0x04    /* we lost arbitration */
+#define EXC_PHASEMM     0x02    /* SCSI phase mismatch */
+#define EXC_SELTO       0x01    /* selection timeout */
+
+/* Bits in the error register */
+#define ERR_UNEXPDISC   0x40    /* target unexpectedly disconnected */
+#define ERR_SCSIRESET   0x20    /* SCSI bus got reset on us */
+#define ERR_SEQERR      0x10    /* we did something the chip didn't like */
+#define ERR_PARITY      0x01    /* parity error was detected */
+
+/* Bits in the interrupt and intr_mask registers */
+#define INT_ERROR       0x04    /* error interrupt */
+#define INT_EXCEPTION   0x02    /* exception interrupt */
+#define INT_CMDDONE     0x01    /* command done interrupt */
+
+/* Fields in the sync_params register */
+#define SYNC_OFF(x)     ((x) >> 4)      /* offset field */
+#define SYNC_PER(x)     ((x) & 0xf)     /* period field */
+#define SYNC_PARAMS(o, p)       (((o) << 4) | (p))
+#define ASYNC_PARAMS    2       /* sync_params value for async xfers */
+
+/*
+ * Assuming a clock frequency of 50MHz:
+ *
+ * The transfer period with SYNC_PER(sync_params) == x
+ * is (x + 2) * 40ns, except that x == 0 gives 100ns.
+ *
+ * The units of the sel_timeout register are 10ms.
+ */
+
+
+#endif /* _MESH_H */