cs89x0: Removing dead SH_HICOSH4

SH_HICOSH4 doesn't exist in Kconfig, therefore removing all references
for it from the source code.

Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

2 files changed, 2 insertions, 53 deletions

diff --git a/drivers/net/cs89x0.c b/drivers/net/cs89x0.c
index e3a7dca23025..89f2ef7f16de 100644
--- a/drivers/net/cs89x0.c
+++ b/drivers/net/cs89x0.c
@@ -170,11 +170,7 @@ static char version[] __initdata =
 /* The cs8900 has 4 IRQ pins, software selectable. cs8900_irq_map maps
    them to system IRQ numbers. This mapping is card specific and is set to
    the configuration of the Cirrus Eval board for this chip. */
-#if defined(CONFIG_SH_HICOSH4)
-static unsigned int netcard_portlist[] __used __initdata =
-   { 0x0300, 0};
-static unsigned int cs8900_irq_map[] = {1,0,0,0};
-#elif defined(CONFIG_MACH_IXDP2351)
+#if defined(CONFIG_MACH_IXDP2351)
 static unsigned int netcard_portlist[] __used __initdata = {IXDP2351_VIRT_CS8900_BASE, 0};
 static unsigned int cs8900_irq_map[] = {IRQ_IXDP2351_CS8900, 0, 0, 0};
 #elif defined(CONFIG_ARCH_IXDP2X01)
@@ -578,12 +574,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
                 goto out1;
         }
 
-#ifdef CONFIG_SH_HICOSH4
-        /* truly reset the chip */
-        writeword(ioaddr, ADD_PORT, 0x0114);
-        writeword(ioaddr, DATA_PORT, 0x0040);
-#endif
-
         /* if they give us an odd I/O address, then do ONE write to
            the address port, to get it back to address zero, where we
            expect to find the EISA signature word. An IO with a base of 0x3
@@ -649,37 +639,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
            the driver will always do *something* instead of complain that
            adapter_cnf is 0. */
 
-#ifdef CONFIG_SH_HICOSH4
-        if (1) {
-                /* For the HiCO.SH4 board, things are different: we don't
-                   have EEPROM, but there is some data in flash, so we go
-                   get it there directly (MAC). */
-                __u16 *confd;
-                short cnt;
-                if (((* (volatile __u32 *) 0xa0013ff0) & 0x00ffffff)
-                        == 0x006c3000) {
-                        confd = (__u16*) 0xa0013fc0;
-                } else {
-                        confd = (__u16*) 0xa001ffc0;
-                }
-                cnt = (*confd++ & 0x00ff) >> 1;
-                while (--cnt > 0) {
-                        __u16 j = *confd++;
-
-                        switch (j & 0x0fff) {
-                        case PP_IA:
-                                for (i = 0; i < ETH_ALEN/2; i++) {
-                                        dev->dev_addr[i*2] = confd[i] & 0xFF;
-                                        dev->dev_addr[i*2+1] = confd[i] >> 8;
-                                }
-                                break;
-                        }
-                        j = (j >> 12) + 1;
-                        confd += j;
-                        cnt -= j;
-                }
-        } else
-#endif
 
         if ((readreg(dev, PP_SelfST) & (EEPROM_OK | EEPROM_PRESENT)) ==
               (EEPROM_OK|EEPROM_PRESENT)) {
@@ -734,11 +693,7 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
         printk("\n");
 
         /* First check to see if an EEPROM is attached. */
-#ifdef CONFIG_SH_HICOSH4 /* no EEPROM on HiCO, don't hazzle with it here */
-        if (1) {
-                printk(KERN_NOTICE "cs89x0: No EEPROM on HiCO.SH4\n");
-        } else
-#endif
+
         if ((readreg(dev, PP_SelfST) & EEPROM_PRESENT) == 0)
                 printk(KERN_WARNING "cs89x0: No EEPROM, relying on command line....\n");
         else if (get_eeprom_data(dev, START_EEPROM_DATA,CHKSUM_LEN,eeprom_buff) < 0) {
@@ -1275,7 +1230,6 @@ net_open(struct net_device *dev)
         int i;
         int ret;
 
-#if !defined(CONFIG_SH_HICOSH4) && !defined(CONFIG_ARCH_PNX010X) /* uses irq#1, so this won't work */
         if (dev->irq < 2) {
                 /* Allow interrupts to be generated by the chip */
 /* Cirrus' release had this: */
@@ -1304,7 +1258,6 @@ net_open(struct net_device *dev)
                 }
         }
         else
-#endif
         {
 #ifndef CONFIG_CS89x0_NONISA_IRQ
                 if (((1 << dev->irq) & lp->irq_map) == 0) {
diff --git a/drivers/net/cs89x0.h b/drivers/net/cs89x0.h
index 204ed37fa9d5..91423b70bb45 100644
--- a/drivers/net/cs89x0.h
+++ b/drivers/net/cs89x0.h
@@ -437,11 +437,7 @@
 #define IRQ_MAP_EEPROM_DATA 0x0046 /*  Offset into eeprom for the IRQ map */
 #define IRQ_MAP_LEN 0x0004 /*  No of bytes to read for the IRQ map */
 #define PNP_IRQ_FRMT 0x0022 /*  PNP small item IRQ format */
-#ifdef CONFIG_SH_HICOSH4
-#define CS8900_IRQ_MAP 0x0002 /* HiCO-SH4 board has its IRQ on #1 */
-#else
 #define CS8900_IRQ_MAP 0x1c20 /*  This IRQ map is fixed */
-#endif
 
 #define CS8920_NO_INTS 0x0F   /*  Max CS8920 interrupt select # */