[PATCH] libertas: Purge non-mesh ioctls

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 0 insertions, 516 deletions

diff --git a/drivers/net/wireless/libertas/README b/drivers/net/wireless/libertas/README
index 688da4c784b1..378577200b56 100644
--- a/drivers/net/wireless/libertas/README
+++ b/drivers/net/wireless/libertas/README
@@ -40,64 +40,11 @@ NAME
 SYNOPSIS
         iwpriv <ethX> <command> [sub-command] ...
 
-        iwpriv ethX version
-        iwpriv ethX scantype [sub-command]
-        iwpriv ethX getSNR <n>
-        iwpriv ethX getNF <n>
-        iwpriv ethX getRSSI <n>
-        iwpriv ethX setrxant <n>
-        iwpriv ethX getrxant
-        iwpriv ethX settxant <n>
-        iwpriv ethX gettxant
-        iwpriv ethX authalgs <n>
-        iwpriv ethX pre-TBTT <n>
-        iwpriv ethX 8021xauthalgs <n>
-        iwpriv ethX encryptionmode <n>
         iwpriv ethX setregioncode <n>
         iwpriv ethX getregioncode
-        iwpriv ethX setbcnavg <n>
-        iwpriv ethX getbcnavg
-        iwpriv ethX setdataavg <n>
-        iwpriv ethX setlisteninter <n>
-        iwpriv ethX getlisteninter
-        iwpriv ethX setmultipledtim <n>
-        iwpriv ethX getmultipledtim
-        iwpriv ethX atimwindow <n>
-        iwpriv ethX deauth
-        iwpriv ethX adhocstop
-        iwpriv ethX radioon
-        iwpriv ethX radiooff
-        iwpriv ethX reasso-on
-        iwpriv ethX reasso-off
-        iwpriv ethX scanmode  [sub-command]
-        iwpriv ethX setwpaie <n>
-        iwpriv ethX wlanidle-off
-        iwpriv ethX wlanidle-on
-        iwpriv ethX getcis
-        iwpriv ethX getlog
-        iwpriv ethX getadhocstatus
-        iwpriv ethX adhocgrate <n>
-
-Version 4 Command:
-        iwpriv ethX inactvityto <n>
-        iwpriv ethX sleeppd <n>
-        iwpriv ethX enable11d <n>
-        iwpriv ethX tpccfg <n>
-        iwpriv ethX powercfg <n>
-        iwpriv ethX setafc <n>
-        iwpriv ethX getafc
 
 Version 5 Command:
         iwpriv ethX ledgpio <n>
-        iwpriv ethX scanprobes <n>
-        iwpriv ethX lolisteninter <n>
-        iwpriv ethX rateadapt <n> <m>
-        iwpriv ethX txcontrol <n>
-        iwpriv ethX psnullinterval <n>
-        iwpriv ethX prescan <n>
-        iwpriv ethX getrxinfo
-        iwpriv ethX gettxrate
-        iwpriv ethX beaconinterval
 
 BT Commands:
         The blinding table (BT) contains a list of mac addresses that should be
@@ -150,114 +97,6 @@ DESCRIPTION
         The ethX parameter specifies the network device that is to be used to
                 perform this command on. it could be eth0, eth1 etc.
 
-version
-        This is used to get the current version of the driver and the firmware.
-
-scantype
-        This command is used to set the scan type to be used by the driver in
-        the scan command. This setting will not be used while performing a scan
-        for a specific SSID, as it is always done with scan type being active.
-
-        where the sub-commands are: -
-                        active  -- to set the scan type to active
-                        passive -- to set the scan type to passive
-                        get     -- to get the scan type set in the driver
-
-getSNR
-        This command gets the average and non average value of Signal to Noise
-        Ratio of Beacon and Data.
-
-        where value is:-
-                        0       -- Beacon non-average.
-                        1       -- Beacon average.
-                        2       -- Data non-average.
-                        3       -- Data average.
-
-        If no value is given, all four values are returned in the order mentioned
-        above.
-
-        Note: This command is available only when STA is connected.
-
-getRSSI
-        This command gets the average and non average value os Receive Signal
-        Strength of Beacon and Data.
-
-        where value is:-
-                        0       -- Beacon non-average.
-                        1       -- Beacon average.
-                        2       -- Data non-average.
-                        3       -- Data average.
-
-        Note: This command is available only when STA is connected.
-
-getNF
-        This command gets the average and non average value of Noise Floor of
-        Beacon and Data.
-
-        where value is:-
-                        0       -- Beacon non-average.
-                        1       -- Beacon average.
-                        2       -- Data non-average.
-                        3       -- Data average.
-
-        Note: This command is available only when STA is connected.
-
-setrxant
-        This command is used to set the mode for Rx antenna.
-
-        The options that can be sent are:-
-                        1       -- Antenna 1.
-                        2       -- Antenna 2.
-                        0xFFFF  -- Diversity.
-
-        Usage:
-                iwpriv ethX setrxant 0x01: select Antenna 1.
-
-getrxant
-        This command is used to get the mode for Rx antenna.
-
-
-settxant
-        This command is used to set the mode for Tx antenna.
-                The options that can be sent are:-
-                        1       -- Antenna 1.
-                        2       -- Antenna 2.
-                        0xFFFF  -- Diversity.
-        Usage:
-                iwpriv ethX settxant 0x01: select Antenna 1.
-
-gettxant
-        This command is used to get the mode for Tx antenna.
-
-authalgs
-        This command is used by the WPA supplicant to set the authentication
-        algorithms in the station.
-
-8021xauthalgs
-        This command is used by the WPA supplicant to set the 8021.x authentication algorithm type
-        station.
-
-        where values can be:-
-                        1       -- None
-                        2       -- LEAP
-                        4       -- TLS
-                        8       -- TTLs
-                        16      -- MD5
-
-
-encryptionmode
-        This command is used by the WPA supplicant to set the encryption algorithm.
-
-        where values can be:-
-                        0       -- NONE
-                        1       -- WEP40
-                        2       -- TKIP
-                        3       -- CCMP
-                        4       -- WEP104
-
-pre-TBTT
-        This command is used to set pre-TBTT time period where value is in microseconds.
-
 setregioncode
         This command is used to set the region code in the station.
         where value is 'region code' for various regions like
@@ -270,114 +109,6 @@ getregioncode
         This command is used to get the region code information set in the
         station.
 
-setbcnavg
-        Set the weighting factor for calculating RSSI.
-
-getbcnavg
-        Get weighting factor for calculating RSSI.
-
-setdataavg
-        Set the weighting factor for calculating SNR.
-
-setlisteninter
-        This command is used to set the listen interval in the
-        station.
-
-        where the value ranges between 1 - 255
-
-getlisteninter
-        This command is used to get the listen interval value set in the
-        station.
-
-setmultipledtim
-        This command is used to set the multiple dtim value in the
-        station.
-                where the value is 1,2,3,4,5,0xfffe
-                0xfffe means the firmware will use listen interval in association
-                command for waking up
-
-getmultipledtim
-        This command is used to get the multiple dtim value set in the station.
-
-atimwindow
-        This command is used to set the atim value in the
-        station.
-
-        where the value ranges between 0 - 50
-
-deauth
-        This command is used to send the de-authentication to the AP with which
-        the station is associated. This command is valid only when
-        station is in Infrastructure mode.
-
-        Note: This command is available only when STA is connected.
-
-adhocstop
-        This command is used to stop beacon transmission from the station and
-        go into idle state in ad-hoc mode.
-
-        Note: This command is available only when STA is connected.
-
-radioon
-        This command is used to turn on the RF antenna.
-
-radiooff
-        This command is sued to turn off the RF antenna.
-
-scanmode
-        This command is used to set the station to scan for either IBSS
-        networks or BSS networks or both BSS and IBSS networks. This
-        command can be used with sub commands,
-
-        where the value for
-                        bss     -- Scan All the BSS networks.
-                        ibss    -- Scan All the IBSS networks.
-                        any     -- Scan both BSS and IBSS networks.
-
-
-
-setwpaie
-        This command is used by WPA supplicant to send the WPA-IE to the driver.
-
-wlanidle-off
-        This command is used to get into idle state.
-
-        Note: This command is available only when STA is connected.
-
-wlanidle-on
-        This command is used to get off the idle state.
-
-        Note: This command is available only when STA is connected.
-
-
-getlog
-        This command is used to get the 802.11 statistics available in the
-                station.
-
-        Note: This command is available only when STA is connected.
-
-getadhocstatus
-        This command is used to get the ad-hoc Network Status.
-
-        The various status codes are:
-                AdhocStarted
-                AdhocJoined
-                AdhocIdle
-                InfraMode
-                AutoUnknownMode
-
-        Note: This command is available only when STA is connected.
-
-adhocgrate
-        This command is used to enable(1) g_rate, Disable(0) g_rate
-        and request(2) the status which g_rate is disabled/enabled,
-        for Ad-hoc creator.
-
-        where value is:-
-                0       -- Disabled
-                1       -- Enabled
-                2       -- Get
-
 ledgpio
         This command is used to set/get LEDs.
 
@@ -400,253 +131,6 @@ ledgpio
         Note: LED0 is invalid
         Note: Maximum Number of LEDs are 16.
 
-inactivityto
-        This command is used by the host to set/get the inactivity timeout value,
-        which specifies when WLAN device is put to sleep.
-
-        Usage:
-                iwpriv ethX inactivityto [<timeout>]
-
-        where the parameter are:
-                timeout: timeout value in milliseconds.
-
-        Example:
-                iwpriv eth1 inactivityto
-                        "get the timeout value"
-
-                iwpriv eth1 inactivityto X
-                        "set timeout value to X ms"
-
-
-sleeppd
-        This command is used to configure the sleep period of the WLAN device.
-
-        Usage:
-                iwpriv ethX sleeppd [<sleep period>]
-
-        where the parameter are:
-                Period: sleep period in milliseconds. Range 10~60.
-
-        Example:
-                iwpriv eth1 sleeppd 10
-                        "set period as 10 ms"
-                iwpriv eth1 sleeppd
-                        "get the sleep period configuration"
-
-enable11d
-        This command is used to control 11d
-        where value is:-
-                1       -- Enabled
-                0       -- Disabled
-                2       -- Get
-
-
-
-
-tpccfg
-        Enables or disables automatic transmit power control.
-
-        The first parameter turns this feature on (1) or off (0).  When turning
-        on, the user must also supply four more parameters in the following
-        order:
-                -UseSNR (Use SNR (in addition to PER) for TPC algorithm),
-                -P0 (P0 power level for TPC),
-                -P1 (P1 power level for TPC),
-                -P2 (P2 power level for TPC).
-
-        Usage:
-                iwpriv ethX tpccfg: Get current configuration
-                iwpriv ethX tpccfg 0: disable auto TPC
-                iwpriv ethX tpccfg 0x01 0x00 0x05 0x0a 0x0d: enable auto TPC; do not use SNR;
-                                                             P0=0x05; P1=0x0a; P2=0x0d;
-                iwpriv ethX tpccfg 0x01 0x01 0x05 0x0a 0x0d: enable auto TPC; use SNR;
-                                                             P0=0x05; P1=0x0a; P2=0x0d.
-
-powercfg
-        Enables or disables power adaptation.
-
-        The first parameter turns this feature on (1) or off (0).  When turning
-        on, the user must also supply three more parameters in the following
-        order:
-                -P0 (P0 power level for Power Adaptation),
-                -P1 (P1 power level for Power Adaptation),
-                -P2 (P2 power level for Power Adaptation).
-
-        Usage:
-                iwpriv ethX powercfg: Get current configuration
-                iwpriv ethX powercfg 0: disable power adaptation
-                iwpriv ethX powercfg 1 0x0d 0x0f 0x12: enable power adaptation;
-                                                       P0=0x0d; P1=0x0f; P2=0x12.
-
-getafc
-        This command returns automatic frequency control parameters.  It returns
-        three integers:
-                -P0: automatic is on (1), or off (0),
-                -P1: current timing offset in PPM (part per million), and
-                -P2: current frequency offset in PPM.
-
-setafc
-        Set automatic frequency control options.
-
-        The first parameter turns automatic on (1) or off (0).
-        The user must supply two more parameters in either case, in the following
-  order:
-
-  When auto is on:
-
-                -P0 (automatic adjustment frequency threshold in PPM),
-                -P1 (automatic adjustment period in beacon period),
-
-  When auto is off:
-
-                -P0 (manual adjustment timing offset in PPM), and
-                -P1 (manual adjustment frequency offset in PPM).
-
-        Usage:
-                iwpriv ethX setafc 0 10 10: manual adjustment, both timing and frequcncy
-    offset are 10 PPM.
-
-                iwpriv ethX setafc 1 10 10 enable afc, automatic adjustment,
-    frequency threshold 10 PPM, for every 10 beacon periods.
-
-
-
-scanprobes
-        This command sets number of probe requests per channel.
-
-        Usage:
-                iwpriv ethX scanprobes 3 (set scan probes to 3)
-                iwpriv ethX scanprobes   (get scan probes)
-
-lolisteninter
-        This command sets the value of listen interval.
-
-        Usage:
-        iwpriv ethX lolisteninter 234 (set the lolisteninter to 234)
-        iwpriv ethX lolisteninter     (get the lolisteninter value)
-
-rateadapt
-        This command sets the data rates bitmap.
-        Where <n>
-                0: Disable auto rate adapt
-                1: Enable auto rate adapt
-
-              <m>
-                 data rate bitmap
-                        Bit     Data rate
-                        0       1 Mbps
-                        1       2 Mbps
-                        2       5.5 Mbps
-                        3       11 Mbps
-                        4       Reserved
-                        5       6 Mbps
-                        6       9 Mbps
-                        7       12 Mbps
-                        8       18 Mbps
-                        9       24 Mbps
-                        10      36 Mbps
-                        11      48 Mbps
-                        12      54 Mbps
-                        12-15   Reserved
-
-        Usage:
-        iwpriv ethX rateadapt
-                        read the currect data rate setting
-        iwpriv ethX rateadapt 1 0x07
-                        enable auto data rate adapt and
-                        data rates are 1Mbps, 2Mbsp and 5.5Mbps
-
-
-txcontrol
-        This command is used to set the Tx rate, ack policy, and retry limit on a per packet basis.
-
-        Where value <n> is:
-            if bit[4] == 1:
-                bit[3:0]        -- 0   1   2   3   4   5   6   7   8   9   10   11   12   13-16
-                Data Rate(Mbps) -- 1   2   5.5 11  Rsv 6   9   12  18  24  36   48   54   Rsv
-
-            bit[12:8]
-                if bit[12] == 1, bit[11:8] specifies the Tx retry limit.
-
-            bit[14:13] specifies per packet ack policy:
-                bit[14:13]
-                     1  0       use immediate ack policy for this packet
-                     1  1       use no ack policy for this packet
-                     0  x       use the per-packet ack policy setting
-
-        Usage:
-        iwpriv ethX txcontrol 0x7513
-                        Use no-ack policy, 5 retires for Tx, 11Mbps rate
-
-
-
-psnullinterval
-        This command is used to set/request NULL package interval for Power Save
-        under infrastructure mode.
-
-        where value is:-
-                -1      -- Disabled
-                n>0     -- Set interval as n (seconds)
-
-prescan
-        This command is used to enable (1)/disable(0) auto prescan before assoicate to the ap
-
-        where value is:-
-                0       -- Disabled
-                1       -- Enabled
-                2       -- Get
-
-getrxinfo
-        This command gets non average value of Signal to Noise Ratio of Data and rate index.
-
-        The following table shows RateIndex and Rate
-
-                     RateIndex  Data rate
-                        0       1 Mbps
-                        1       2 Mbps
-                        2       5.5 Mbps
-                        3       11 Mbps
-                        4       Reserved
-                        5       6 Mbps
-                        6       9 Mbps
-                        7       12 Mbps
-                        8       18 Mbps
-                        9       24 Mbps
-                        10      36 Mbps
-                        11      48 Mbps
-                        12      54 Mbps
-                        13-15   Reserved
-
-gettxrate
-        This command gets current Tx rate index of the first packet associated with Rate Adaptation.
-
-        The following table shows RateIndex and Rate
-
-                     RateIndex  Data rate
-                        0       1 Mbps
-                        1       2 Mbps
-                        2       5.5 Mbps
-                        3       11 Mbps
-                        4       Reserved
-                        5       6 Mbps
-                        6       9 Mbps
-                        7       12 Mbps
-                        8       18 Mbps
-                        9       24 Mbps
-                        10      36 Mbps
-                        11      48 Mbps
-                        12      54 Mbps
-                        13-15   Reserved
-
-bcninterval
-        This command is used to sets beacon interval in adhoc mode when an argument is given, and gets current adhoc
-        beacon interval when no argument is given. The valid beacon interval is between 20 - 1000,
-        default beacon interval is 100.
-
-        Usage:
-                iwpriv ethX bcninterval 100  (set adhoc beacon interval to 100)
-                iwpriv ethX bcninterval      (get adhoc beacon interval)
-
 fwt_add
         This command is used to insert an entry into the FWT table. The list of
         parameters must follow the following structure: