Merge branch 'for-next' into for-linus

Conflicts:

	kernel/irq/chip.c

3 files changed, 6 insertions, 6 deletions

diff --git a/drivers/net/wireless/ath/ath5k/base.h b/drivers/net/wireless/ath/ath5k/base.h
index a28c42f32c9d..4da029410467 100644
--- a/drivers/net/wireless/ath/ath5k/base.h
+++ b/drivers/net/wireless/ath/ath5k/base.h
@@ -36,7 +36,7 @@
  */
 
 /*
- * Defintions for the Atheros Wireless LAN controller driver.
+ * Definitions for the Atheros Wireless LAN controller driver.
  */
 #ifndef _DEV_ATH_ATHVAR_H
 #define _DEV_ATH_ATHVAR_H
@@ -193,7 +193,7 @@ struct ath5k_softc {
         struct ath5k_txq        *cabq;          /* content after beacon */
 
         int                     power_level;    /* Requested tx power in dbm */
-        bool                    assoc;          /* assocate state */
+        bool                    assoc;          /* associate state */
         bool                    enable_beacon;  /* true if beacons are on */
 };
 
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c
index 644962adda97..81ea52c4faff 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.c
+++ b/drivers/net/wireless/ath/ath5k/eeprom.c
@@ -1492,7 +1492,7 @@ ath5k_eeprom_read_target_rate_pwr_info(struct ath5k_hw *ah, unsigned int mode)
  * This info is used to calibrate the baseband power table. Imagine
  * that for each channel there is a power curve that's hw specific
  * (depends on amplifier etc) and we try to "correct" this curve using
- * offests we pass on to phy chip (baseband -> before amplifier) so that
+ * offsets we pass on to phy chip (baseband -> before amplifier) so that
  * it can use accurate power values when setting tx power (takes amplifier's
  * performance on each channel into account).
  *
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index 1a039f2bd732..6f04cc758dcc 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -117,7 +117,7 @@ static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah,
 
 /*
  * This code is used to optimize rf gain on different environments
- * (temprature mostly) based on feedback from a power detector.
+ * (temperature mostly) based on feedback from a power detector.
  *
  * It's only used on RF5111 and RF5112, later RF chips seem to have
  * auto adjustment on hw -notice they have a much smaller BANK 7 and
@@ -2675,7 +2675,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,
                 /* Fill curves in reverse order
                  * from lower power (max gain)
                  * to higher power. Use curve -> idx
-                 * backmaping we did on eeprom init */
+                 * backmapping we did on eeprom init */
                 u8 idx = pdg_curve_to_idx[pdg];
 
                 /* Grab the needed curves by index */
@@ -2777,7 +2777,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,
         /* Now we have a set of curves for this
          * channel on tmpL (x range is table_max - table_min
          * and y values are tmpL[pdg][]) sorted in the same
-         * order as EEPROM (because we've used the backmaping).
+         * order as EEPROM (because we've used the backmapping).
          * So for RF5112 it's from higher power to lower power
          * and for RF2413 it's from lower power to higher power.
          * For RF5111 we only have one curve. */