[PATCH] sky2: remove unused definitions

The sky2 driver has a lot of register definitions, that were
copied over from the skge driver, for areas that don't exist
on the Yukon2.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

1 files changed, 4 insertions, 32 deletions

diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index b1acdc606f31..c15d46409bcc 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -85,21 +85,6 @@ enum csr_regs {
         B0_IMSK         = 0x000c,
         B0_HWE_ISRC     = 0x0010,
         B0_HWE_IMSK     = 0x0014,
-        B0_SP_ISRC      = 0x0018,
-        B0_XM1_IMSK     = 0x0020,
-        B0_XM1_ISRC     = 0x0028,
-        B0_XM1_PHY_ADDR = 0x0030,
-        B0_XM1_PHY_DATA = 0x0034,
-        B0_XM2_IMSK     = 0x0040,
-        B0_XM2_ISRC     = 0x0048,
-        B0_XM2_PHY_ADDR = 0x0050,
-        B0_XM2_PHY_DATA = 0x0054,
-        B0_R1_CSR       = 0x0060,
-        B0_R2_CSR       = 0x0064,
-        B0_XS1_CSR      = 0x0068,
-        B0_XA1_CSR      = 0x006c,
-        B0_XS2_CSR      = 0x0070,
-        B0_XA2_CSR      = 0x0074,
 
         /* Special ISR registers (Yukon-2 only) */
         B0_Y2_SP_ISRC2  = 0x001c,
@@ -116,36 +101,25 @@ enum csr_regs {
         B2_MAC_CFG      = 0x011a,
         B2_CHIP_ID      = 0x011b,
         B2_E_0          = 0x011c,
-        B2_E_1          = 0x011d,
-        B2_E_2          = 0x011e,
+
         B2_Y2_CLK_GATE  = 0x011d,
         B2_Y2_HW_RES    = 0x011e,
         B2_E_3          = 0x011f,
         B2_Y2_CLK_CTRL  = 0x0120,
-        B2_LD_CTRL      = 0x0128,
-        B2_LD_TEST      = 0x0129,
+
         B2_TI_INI       = 0x0130,
         B2_TI_VAL       = 0x0134,
         B2_TI_CTRL      = 0x0138,
         B2_TI_TEST      = 0x0139,
-        B2_IRQM_INI     = 0x0140,
-        B2_IRQM_VAL     = 0x0144,
-        B2_IRQM_CTRL    = 0x0148,
-        B2_IRQM_TEST    = 0x0149,
-        B2_IRQM_MSK     = 0x014c,
-        B2_IRQM_HWE_MSK = 0x0150,
+
         B2_TST_CTRL1    = 0x0158,
         B2_TST_CTRL2    = 0x0159,
         B2_GP_IO        = 0x015c,
+
         B2_I2C_CTRL     = 0x0160,
         B2_I2C_DATA     = 0x0164,
         B2_I2C_IRQ      = 0x0168,
         B2_I2C_SW       = 0x016c,
-        B2_BSC_INI      = 0x0170,
-        B2_BSC_VAL      = 0x0174,
-        B2_BSC_CTRL     = 0x0178,
-        B2_BSC_STAT     = 0x0179,
-        B2_BSC_TST      = 0x017a,
 
         B3_RAM_ADDR     = 0x0180,
         B3_RAM_DATA_LO  = 0x0184,
@@ -220,8 +194,6 @@ enum {
         Y2_LED_STAT_ON  = 1<<9, /* Status LED On  (YUKON-2 only) */
         Y2_LED_STAT_OFF = 1<<8, /* Status LED Off (YUKON-2 only) */
 
-        CS_BUS_CLOCK    = 1<<9, /* Bus Clock 0/1 = 33/66 MHz */
-        CS_BUS_SLOT_SZ  = 1<<8, /* Slot Size 0/1 = 32/64 bit slot */
         CS_ST_SW_IRQ    = 1<<7, /* Set IRQ SW Request */
         CS_CL_SW_IRQ    = 1<<6, /* Clear IRQ SW Request */
         CS_STOP_DONE    = 1<<5, /* Stop Master is finished */