[PATCH] sky2: fiber support

Fix the support for fiber connected gigabit boards.
Allow half duplex gigabit to be configured.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 49 insertions, 32 deletions

diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index a3a4ab26044a..2b9272c0955a 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -308,7 +308,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
         }
 
         ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
-        if (hw->copper) {
+        if (sky2_is_copper(hw)) {
                 if (hw->chip_id == CHIP_ID_YUKON_FE) {
                         /* enable automatic crossover */
                         ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1;
@@ -325,25 +325,37 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
                                 ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
                         }
                 }
-                gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
         } else {
                 /* workaround for deviation #4.88 (CRC errors) */
                 /* disable Automatic Crossover */
 
                 ctrl &= ~PHY_M_PC_MDIX_MSK;
-                gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+        }
 
-                if (hw->chip_id == CHIP_ID_YUKON_XL) {
-                        /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
-                        gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
-                        ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
-                        ctrl &= ~PHY_M_MAC_MD_MSK;
-                        ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
-                        gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+        gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+        /* special setup for PHY 88E1112 Fiber */
+        if (hw->chip_id == CHIP_ID_YUKON_XL && !sky2_is_copper(hw)) {
+                pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
 
+                /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */
+                gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
+                ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+                ctrl &= ~PHY_M_MAC_MD_MSK;
+                ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX);
+                gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+                if (hw->pmd_type  == 'P') {
                         /* select page 1 to access Fiber registers */
                         gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1);
+
+                        /* for SFP-module set SIGDET polarity to low */
+                        ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+                        ctrl |= PHY_M_FIB_SIGD_POL;
+                        gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
                 }
+
+                gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
         }
 
         ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
@@ -361,7 +373,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
         reg = 0;
 
         if (sky2->autoneg == AUTONEG_ENABLE) {
-                if (hw->copper) {
+                if (sky2_is_copper(hw)) {
                         if (sky2->advertising & ADVERTISED_1000baseT_Full)
                                 ct1000 |= PHY_M_1000C_AFD;
                         if (sky2->advertising & ADVERTISED_1000baseT_Half)
@@ -374,8 +386,12 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
                                 adv |= PHY_M_AN_10_FD;
                         if (sky2->advertising & ADVERTISED_10baseT_Half)
                                 adv |= PHY_M_AN_10_HD;
-                } else          /* special defines for FIBER (88E1011S only) */
-                        adv |= PHY_M_AN_1000X_AHD | PHY_M_AN_1000X_AFD;
+                } else {        /* special defines for FIBER (88E1040S only) */
+                        if (sky2->advertising & ADVERTISED_1000baseT_Full)
+                                adv |= PHY_M_AN_1000X_AFD;
+                        if (sky2->advertising & ADVERTISED_1000baseT_Half)
+                                adv |= PHY_M_AN_1000X_AHD;
+                }
 
                 /* Set Flow-control capabilities */
                 if (sky2->tx_pause && sky2->rx_pause)
@@ -1496,7 +1512,7 @@ static int sky2_down(struct net_device *dev)
 
 static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux)
 {
-        if (!hw->copper)
+        if (!sky2_is_copper(hw))
                 return SPEED_1000;
 
         if (hw->chip_id == CHIP_ID_YUKON_FE)
@@ -2269,7 +2285,7 @@ static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk)
 static int sky2_reset(struct sky2_hw *hw)
 {
         u16 status;
-        u8 t8, pmd_type;
+        u8 t8;
         int i;
 
         sky2_write8(hw, B0_CTST, CS_RST_CLR);
@@ -2315,9 +2331,7 @@ static int sky2_reset(struct sky2_hw *hw)
                 sky2_pci_write32(hw, PEX_UNC_ERR_STAT, 0xffffffffUL);
 
 
-        pmd_type = sky2_read8(hw, B2_PMD_TYP);
-        hw->copper = !(pmd_type == 'L' || pmd_type == 'S');
-
+        hw->pmd_type = sky2_read8(hw, B2_PMD_TYP);
         hw->ports = 1;
         t8 = sky2_read8(hw, B2_Y2_HW_RES);
         if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) {
@@ -2414,21 +2428,22 @@ static int sky2_reset(struct sky2_hw *hw)
 
 static u32 sky2_supported_modes(const struct sky2_hw *hw)
 {
-        u32 modes;
-        if (hw->copper) {
-                modes = SUPPORTED_10baseT_Half
-                    | SUPPORTED_10baseT_Full
-                    | SUPPORTED_100baseT_Half
-                    | SUPPORTED_100baseT_Full
-                    | SUPPORTED_Autoneg | SUPPORTED_TP;
+        if (sky2_is_copper(hw)) {
+                u32 modes = SUPPORTED_10baseT_Half
+                        | SUPPORTED_10baseT_Full
+                        | SUPPORTED_100baseT_Half
+                        | SUPPORTED_100baseT_Full
+                        | SUPPORTED_Autoneg | SUPPORTED_TP;
 
                 if (hw->chip_id != CHIP_ID_YUKON_FE)
                         modes |= SUPPORTED_1000baseT_Half
-                            | SUPPORTED_1000baseT_Full;
+                                | SUPPORTED_1000baseT_Full;
+                return modes;
         } else
-                modes = SUPPORTED_1000baseT_Full | SUPPORTED_FIBRE
-                    | SUPPORTED_Autoneg;
-        return modes;
+                return  SUPPORTED_1000baseT_Half
+                        | SUPPORTED_1000baseT_Full
+                        | SUPPORTED_Autoneg
+                        | SUPPORTED_FIBRE;
 }
 
 static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
@@ -2439,7 +2454,7 @@ static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
         ecmd->transceiver = XCVR_INTERNAL;
         ecmd->supported = sky2_supported_modes(hw);
         ecmd->phy_address = PHY_ADDR_MARV;
-        if (hw->copper) {
+        if (sky2_is_copper(hw)) {
                 ecmd->supported = SUPPORTED_10baseT_Half
                     | SUPPORTED_10baseT_Full
                     | SUPPORTED_100baseT_Half
@@ -2448,12 +2463,14 @@ static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
                     | SUPPORTED_1000baseT_Full
                     | SUPPORTED_Autoneg | SUPPORTED_TP;
                 ecmd->port = PORT_TP;
-        } else
+                ecmd->speed = sky2->speed;
+        } else {
+                ecmd->speed = SPEED_1000;
                 ecmd->port = PORT_FIBRE;
+        }
 
         ecmd->advertising = sky2->advertising;
         ecmd->autoneg = sky2->autoneg;
-        ecmd->speed = sky2->speed;
         ecmd->duplex = sky2->duplex;
         return 0;
 }