Merge branch 'linus' into xen-64bit

1 files changed, 199 insertions, 2 deletions

diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 60c5cfe96918..4b4dc98ad165 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -24,6 +24,12 @@
 #define MII_BCM54XX_ESR         0x11    /* BCM54xx extended status register */
 #define MII_BCM54XX_ESR_IS      0x1000  /* Interrupt status */
 
+#define MII_BCM54XX_EXP_DATA    0x15    /* Expansion register data */
+#define MII_BCM54XX_EXP_SEL     0x17    /* Expansion register select */
+#define MII_BCM54XX_EXP_SEL_SSD 0x0e00  /* Secondary SerDes select */
+#define MII_BCM54XX_EXP_SEL_ER  0x0f00  /* Expansion register select */
+
+#define MII_BCM54XX_AUX_CTL     0x18    /* Auxiliary control register */
 #define MII_BCM54XX_ISR         0x1a    /* BCM54xx interrupt status register */
 #define MII_BCM54XX_IMR         0x1b    /* BCM54xx interrupt mask register */
 #define MII_BCM54XX_INT_CRCERR  0x0001  /* CRC error */
@@ -42,10 +48,120 @@
 #define MII_BCM54XX_INT_MDIX    0x2000  /* MDIX status change */
 #define MII_BCM54XX_INT_PSERR   0x4000  /* Pair swap error */
 
+#define MII_BCM54XX_SHD         0x1c    /* 0x1c shadow registers */
+#define MII_BCM54XX_SHD_WRITE   0x8000
+#define MII_BCM54XX_SHD_VAL(x)  ((x & 0x1f) << 10)
+#define MII_BCM54XX_SHD_DATA(x) ((x & 0x3ff) << 0)
+
+/*
+ * Broadcom LED source encodings.  These are used in BCM5461, BCM5481,
+ * BCM5482, and possibly some others.
+ */
+#define BCM_LED_SRC_LINKSPD1    0x0
+#define BCM_LED_SRC_LINKSPD2    0x1
+#define BCM_LED_SRC_XMITLED     0x2
+#define BCM_LED_SRC_ACTIVITYLED 0x3
+#define BCM_LED_SRC_FDXLED      0x4
+#define BCM_LED_SRC_SLAVE       0x5
+#define BCM_LED_SRC_INTR        0x6
+#define BCM_LED_SRC_QUALITY     0x7
+#define BCM_LED_SRC_RCVLED      0x8
+#define BCM_LED_SRC_MULTICOLOR1 0xa
+#define BCM_LED_SRC_OPENSHORT   0xb
+#define BCM_LED_SRC_OFF         0xe     /* Tied high */
+#define BCM_LED_SRC_ON          0xf     /* Tied low */
+
+/*
+ * BCM5482: Shadow registers
+ * Shadow values go into bits [14:10] of register 0x1c to select a shadow
+ * register to access.
+ */
+#define BCM5482_SHD_LEDS1       0x0d    /* 01101: LED Selector 1 */
+                                        /* LED3 / ~LINKSPD[2] selector */
+#define BCM5482_SHD_LEDS1_LED3(src)     ((src & 0xf) << 4)
+                                        /* LED1 / ~LINKSPD[1] selector */
+#define BCM5482_SHD_LEDS1_LED1(src)     ((src & 0xf) << 0)
+#define BCM5482_SHD_SSD         0x14    /* 10100: Secondary SerDes control */
+#define BCM5482_SHD_SSD_LEDM    0x0008  /* SSD LED Mode enable */
+#define BCM5482_SHD_SSD_EN      0x0001  /* SSD enable */
+#define BCM5482_SHD_MODE        0x1f    /* 11111: Mode Control Register */
+#define BCM5482_SHD_MODE_1000BX 0x0001  /* Enable 1000BASE-X registers */
+
+/*
+ * BCM5482: Secondary SerDes registers
+ */
+#define BCM5482_SSD_1000BX_CTL          0x00    /* 1000BASE-X Control */
+#define BCM5482_SSD_1000BX_CTL_PWRDOWN  0x0800  /* Power-down SSD */
+#define BCM5482_SSD_SGMII_SLAVE         0x15    /* SGMII Slave Register */
+#define BCM5482_SSD_SGMII_SLAVE_EN      0x0002  /* Slave mode enable */
+#define BCM5482_SSD_SGMII_SLAVE_AD      0x0001  /* Slave auto-detection */
+
+/*
+ * Device flags for PHYs that can be configured for different operating
+ * modes.
+ */
+#define PHY_BCM_FLAGS_VALID             0x80000000
+#define PHY_BCM_FLAGS_INTF_XAUI         0x00000020
+#define PHY_BCM_FLAGS_INTF_SGMII        0x00000010
+#define PHY_BCM_FLAGS_MODE_1000BX       0x00000002
+#define PHY_BCM_FLAGS_MODE_COPPER       0x00000001
+
 MODULE_DESCRIPTION("Broadcom PHY driver");
 MODULE_AUTHOR("Maciej W. Rozycki");
 MODULE_LICENSE("GPL");
 
+/*
+ * Indirect register access functions for the 1000BASE-T/100BASE-TX/10BASE-T
+ * 0x1c shadow registers.
+ */
+static int bcm54xx_shadow_read(struct phy_device *phydev, u16 shadow)
+{
+        phy_write(phydev, MII_BCM54XX_SHD, MII_BCM54XX_SHD_VAL(shadow));
+        return MII_BCM54XX_SHD_DATA(phy_read(phydev, MII_BCM54XX_SHD));
+}
+
+static int bcm54xx_shadow_write(struct phy_device *phydev, u16 shadow, u16 val)
+{
+        return phy_write(phydev, MII_BCM54XX_SHD,
+                         MII_BCM54XX_SHD_WRITE |
+                         MII_BCM54XX_SHD_VAL(shadow) |
+                         MII_BCM54XX_SHD_DATA(val));
+}
+
+/*
+ * Indirect register access functions for the Expansion Registers
+ * and Secondary SerDes registers (when sec_serdes=1).
+ */
+static int bcm54xx_exp_read(struct phy_device *phydev,
+                            int sec_serdes, u8 regnum)
+{
+        int val;
+
+        phy_write(phydev, MII_BCM54XX_EXP_SEL,
+                  (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
+                                MII_BCM54XX_EXP_SEL_ER) |
+                  regnum);
+        val = phy_read(phydev, MII_BCM54XX_EXP_DATA);
+        phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+
+        return val;
+}
+
+static int bcm54xx_exp_write(struct phy_device *phydev,
+                             int sec_serdes, u8 regnum, u16 val)
+{
+        int ret;
+
+        phy_write(phydev, MII_BCM54XX_EXP_SEL,
+                  (sec_serdes ? MII_BCM54XX_EXP_SEL_SSD :
+                                MII_BCM54XX_EXP_SEL_ER) |
+                  regnum);
+        ret = phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
+        phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
+
+        return ret;
+}
+
 static int bcm54xx_config_init(struct phy_device *phydev)
 {
         int reg, err;
@@ -70,6 +186,87 @@ static int bcm54xx_config_init(struct phy_device *phydev)
         return 0;
 }
 
+static int bcm5482_config_init(struct phy_device *phydev)
+{
+        int err, reg;
+
+        err = bcm54xx_config_init(phydev);
+
+        if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) {
+                /*
+                 * Enable secondary SerDes and its use as an LED source
+                 */
+                reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_SSD);
+                bcm54xx_shadow_write(phydev, BCM5482_SHD_SSD,
+                                     reg |
+                                     BCM5482_SHD_SSD_LEDM |
+                                     BCM5482_SHD_SSD_EN);
+
+                /*
+                 * Enable SGMII slave mode and auto-detection
+                 */
+                reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_SGMII_SLAVE);
+                bcm54xx_exp_write(phydev, 1, BCM5482_SSD_SGMII_SLAVE,
+                                  reg |
+                                  BCM5482_SSD_SGMII_SLAVE_EN |
+                                  BCM5482_SSD_SGMII_SLAVE_AD);
+
+                /*
+                 * Disable secondary SerDes powerdown
+                 */
+                reg = bcm54xx_exp_read(phydev, 1, BCM5482_SSD_1000BX_CTL);
+                bcm54xx_exp_write(phydev, 1, BCM5482_SSD_1000BX_CTL,
+                                  reg & ~BCM5482_SSD_1000BX_CTL_PWRDOWN);
+
+                /*
+                 * Select 1000BASE-X register set (primary SerDes)
+                 */
+                reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_MODE);
+                bcm54xx_shadow_write(phydev, BCM5482_SHD_MODE,
+                                     reg | BCM5482_SHD_MODE_1000BX);
+
+                /*
+                 * LED1=ACTIVITYLED, LED3=LINKSPD[2]
+                 * (Use LED1 as secondary SerDes ACTIVITY LED)
+                 */
+                bcm54xx_shadow_write(phydev, BCM5482_SHD_LEDS1,
+                        BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_ACTIVITYLED) |
+                        BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_LINKSPD2));
+
+                /*
+                 * Auto-negotiation doesn't seem to work quite right
+                 * in this mode, so we disable it and force it to the
+                 * right speed/duplex setting.  Only 'link status'
+                 * is important.
+                 */
+                phydev->autoneg = AUTONEG_DISABLE;
+                phydev->speed = SPEED_1000;
+                phydev->duplex = DUPLEX_FULL;
+        }
+
+        return err;
+}
+
+static int bcm5482_read_status(struct phy_device *phydev)
+{
+        int err;
+
+        err = genphy_read_status(phydev);
+
+        if (phydev->dev_flags & PHY_BCM_FLAGS_MODE_1000BX) {
+                /*
+                 * Only link status matters for 1000Base-X mode, so force
+                 * 1000 Mbit/s full-duplex status
+                 */
+                if (phydev->link) {
+                        phydev->speed = SPEED_1000;
+                        phydev->duplex = DUPLEX_FULL;
+                }
+        }
+
+        return err;
+}
+
 static int bcm54xx_ack_interrupt(struct phy_device *phydev)
 {
         int reg;
@@ -210,9 +407,9 @@ static struct phy_driver bcm5482_driver = {
         .name           = "Broadcom BCM5482",
         .features       = PHY_GBIT_FEATURES,
         .flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
-        .config_init    = bcm54xx_config_init,
+        .config_init    = bcm5482_config_init,
         .config_aneg    = genphy_config_aneg,
-        .read_status    = genphy_read_status,
+        .read_status    = bcm5482_read_status,
         .ack_interrupt  = bcm54xx_ack_interrupt,
         .config_intr    = bcm54xx_config_intr,
         .driver         = { .owner = THIS_MODULE },