Fix misspellings of "system", "controller", "interrupt" and "necessary".

Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>

2 files changed, 12 insertions, 12 deletions

diff --git a/drivers/media/video/bt8xx/bttv-cards.c b/drivers/media/video/bt8xx/bttv-cards.c
index dd6a7d68b07f..3162223a2ff5 100644
--- a/drivers/media/video/bt8xx/bttv-cards.c
+++ b/drivers/media/video/bt8xx/bttv-cards.c
@@ -4709,18 +4709,18 @@ adtvk503_audio(struct bttv *btv, struct video_audio *v, int set)
  *
  * The board hardwire Y0 (xpoint) to MUX1 and MUXOUT to Yin.
  * GPIO pins are wired as:
- *  GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroler)
- *  GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroler)
- *  GPIO[7]   - DATA (xpoint)    - P1[7] (microcontroler)
- *  GPIO[8]   -                  - P3[5] (microcontroler)
- *  GPIO[9]   - RESET (xpoint)   - P3[6] (microcontroler)
- *  GPIO[10]  - STROBE (xpoint)  - P3[7] (microcontroler)
- *  GPINTR    -                  - P3[4] (microcontroler)
+ *  GPIO[0:3] - AX[0:3] (xpoint) - P1[0:3] (microcontroller)
+ *  GPIO[4:6] - AY[0:2] (xpoint) - P1[4:6] (microcontroller)
+ *  GPIO[7]   - DATA (xpoint)    - P1[7] (microcontroller)
+ *  GPIO[8]   -                  - P3[5] (microcontroller)
+ *  GPIO[9]   - RESET (xpoint)   - P3[6] (microcontroller)
+ *  GPIO[10]  - STROBE (xpoint)  - P3[7] (microcontroller)
+ *  GPINTR    -                  - P3[4] (microcontroller)
  *
- * The microcontroler is a 80C32 like. It should be possible to change xpoint
- * configuration either directly (as we are doing) or using the microcontroler
+ * The microcontroller is a 80C32 like. It should be possible to change xpoint
+ * configuration either directly (as we are doing) or using the microcontroller
  * which is also wired to I2C interface. I have no further info on the
- * microcontroler features, one would need to disassembly the firmware.
+ * microcontroller features, one would need to disassembly the firmware.
  * note: the vendor refused to give any information on this product, all
  *       that stuff was found using a multimeter! :)
  */
@@ -4788,7 +4788,7 @@ static void tibetCS16_init(struct bttv *btv)
  * The analog switch is controlled by the "master", but the detection order
  * of the four BT878A chips is in an order which I just don't understand.
  * The "master" is actually the second controller to be detected.  The
- * logic on the board uses logical numbers for the 4 controlers, but
+ * logic on the board uses logical numbers for the 4 controllers, but
  * those numbers are different from the detection sequence.  When working
  * with the analog switch, we need to "map" from the detection sequence
  * over to the board's logical controller number.  This mapping sequence
diff --git a/drivers/media/video/em28xx/em28xx-video.c b/drivers/media/video/em28xx/em28xx-video.c
index b8d5327c438d..e467682aabd7 100644
--- a/drivers/media/video/em28xx/em28xx-video.c
+++ b/drivers/media/video/em28xx/em28xx-video.c
@@ -907,7 +907,7 @@ static int em28xx_set_fmt(struct em28xx *dev, unsigned int cmd, struct v4l2_form
 
         /* stop io in case it is already in progress */
         if (dev->stream == STREAM_ON) {
-                em28xx_videodbg("VIDIOC_SET_FMT: interupting stream\n");
+                em28xx_videodbg("VIDIOC_SET_FMT: interrupting stream\n");
                 if ((ret = em28xx_stream_interrupt(dev)))
                         return ret;
         }