V4L/DVB (4451): MT2060: IF1 Offset from EEPROM, several updates

- AGC gain set to 3
- The tuning sequence has been changed to match the DibCom driver ( from I2C
  spy captures )
- For LITE-ON adapters : The IF1 frequency is now tuned according to the
  calibration values stored in EEPROM.

Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

1 files changed, 312 insertions, 0 deletions

diff --git a/drivers/media/dvb/frontends/mt2060.c b/drivers/media/dvb/frontends/mt2060.c
new file mode 100644
index 000000000000..aa92c1c51e6d
--- /dev/null
+++ b/drivers/media/dvb/frontends/mt2060.c
@@ -0,0 +1,312 @@
+/*
+ *  Driver for Microtune MT2060 "Single chip dual conversion broadband tuner"
+ *
+ *  Copyright (c) 2006 Olivier DANET <odanet@caramail.com>
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.=
+ */
+
+/* See mt2060_priv.h for details */
+
+/* In that file, frequencies are expressed in kiloHertz to avoid 32 bits overflows */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/delay.h>
+#include <linux/dvb/frontend.h>
+#include "mt2060.h"
+#include "mt2060_priv.h"
+
+static int debug=0;
+module_param(debug, int, 0644);
+MODULE_PARM_DESC(debug, "Turn on/off debugging (default:off).");
+
+#define dprintk(args...) do { if (debug) printk(KERN_DEBUG "MT2060: " args); printk("\n"); } while (0)
+
+// Reads a single register
+static int mt2060_readreg(struct mt2060_state *state, u8 reg, u8 *val)
+{
+        struct i2c_msg msg[2] = {
+                { .addr = state->config->i2c_address, .flags = 0,        .buf = &reg, .len = 1 },
+                { .addr = state->config->i2c_address, .flags = I2C_M_RD, .buf = val,  .len = 1 },
+        };
+
+        if (i2c_transfer(state->i2c, msg, 2) != 2) {
+                printk(KERN_WARNING "mt2060 I2C read failed\n");
+                return -EREMOTEIO;
+        }
+        return 0;
+}
+
+// Writes a single register
+static int mt2060_writereg(struct mt2060_state *state, u8 reg, u8 val)
+{
+        u8 buf[2];
+        struct i2c_msg msg = {
+                .addr = state->config->i2c_address, .flags = 0, .buf = buf, .len = 2
+        };
+        buf[0]=reg;
+        buf[1]=val;
+
+        if (i2c_transfer(state->i2c, &msg, 1) != 1) {
+                printk(KERN_WARNING "mt2060 I2C write failed\n");
+                return -EREMOTEIO;
+        }
+        return 0;
+}
+
+// Writes a set of consecutive registers
+static int mt2060_writeregs(struct mt2060_state *state,u8 *buf, u8 len)
+{
+        struct i2c_msg msg = {
+                .addr = state->config->i2c_address, .flags = 0, .buf = buf, .len = len
+        };
+        if (i2c_transfer(state->i2c, &msg, 1) != 1) {
+                printk(KERN_WARNING "mt2060 I2C write failed (len=%i)\n",(int)len);
+                return -EREMOTEIO;
+        }
+        return 0;
+}
+
+// Initialisation sequences
+// LNABAND=3, NUM1=0x3C, DIV1=0x74, NUM2=0x1080, DIV2=0x49
+static u8 mt2060_config1[] = {
+        REG_LO1C1,
+        0x3F,   0x74,   0x00,   0x08,   0x93
+};
+
+// FMCG=2, GP2=0, GP1=0
+static u8 mt2060_config2[] = {
+        REG_MISC_CTRL,
+        0x20,   0x1E,   0x30,   0xff,   0x80,   0xff,   0x00,   0x2c,   0x42
+};
+
+//  VGAG=3, V1CSE=1
+static u8 mt2060_config3[] = {
+        REG_VGAG,
+        0x33
+};
+
+int mt2060_init(struct mt2060_state *state)
+{
+        if (mt2060_writeregs(state,mt2060_config1,sizeof(mt2060_config1)))
+                return -EREMOTEIO;
+        if (mt2060_writeregs(state,mt2060_config3,sizeof(mt2060_config3)))
+                return -EREMOTEIO;
+        return 0;
+}
+EXPORT_SYMBOL(mt2060_init);
+
+#ifdef  MT2060_SPURCHECK
+/* The function below calculates the frequency offset between the output frequency if2
+ and the closer cross modulation subcarrier between lo1 and lo2 up to the tenth harmonic */
+static int mt2060_spurcalc(u32 lo1,u32 lo2,u32 if2)
+{
+        int I,J;
+        int dia,diamin,diff;
+        diamin=1000000;
+        for (I = 1; I < 10; I++) {
+                J = ((2*I*lo1)/lo2+1)/2;
+                diff = I*(int)lo1-J*(int)lo2;
+                if (diff < 0) diff=-diff;
+                dia = (diff-(int)if2);
+                if (dia < 0) dia=-dia;
+                if (diamin > dia) diamin=dia;
+        }
+        return diamin;
+}
+
+#define BANDWIDTH 4000 // kHz
+
+/* Calculates the frequency offset to add to avoid spurs. Returns 0 if no offset is needed */
+static int mt2060_spurcheck(u32 lo1,u32 lo2,u32 if2)
+{
+        u32 Spur,Sp1,Sp2;
+        int I,J;
+        I=0;
+        J=1000;
+
+        Spur=mt2060_spurcalc(lo1,lo2,if2);
+        if (Spur < BANDWIDTH) {
+                /* Potential spurs detected */
+                dprintk("Spurs before : f_lo1: %d  f_lo2: %d  (kHz)",
+                        (int)lo1,(int)lo2);
+                I=1000;
+                Sp1 = mt2060_spurcalc(lo1+I,lo2+I,if2);
+                Sp2 = mt2060_spurcalc(lo1-I,lo2-I,if2);
+
+                if (Sp1 < Sp2) {
+                        J=-J; I=-I; Spur=Sp2;
+                } else
+                        Spur=Sp1;
+
+                while (Spur < BANDWIDTH) {
+                        I += J;
+                        Spur = mt2060_spurcalc(lo1+I,lo2+I,if2);
+                }
+                dprintk("Spurs after  : f_lo1: %d  f_lo2: %d  (kHz)",
+                        (int)(lo1+I),(int)(lo2+I));
+        }
+        return I;
+}
+#endif
+
+#define IF2  36150       // IF2 frequency = 36.150 MHz
+#define FREF 16000       // Quartz oscillator 16 MHz
+
+int mt2060_set(struct mt2060_state *state, struct dvb_frontend_parameters *fep)
+{
+        int ret=0;
+        int i=0;
+        u32 freq;
+        u8  lnaband;
+        u32 f_lo1,f_lo2;
+        u32 div1,num1,div2,num2;
+        u8  b[8];
+        u32 if1;
+
+        if1 = state->if1_freq;
+        b[0] = REG_LO1B1;
+        b[1] = 0xFF;
+        mt2060_writeregs(state,b,2);
+
+        freq = fep->frequency / 1000; // Hz -> kHz
+
+        f_lo1 =  freq + if1 * 1000;
+        f_lo1 = (f_lo1/250)*250;
+        f_lo2 =  f_lo1 - freq - IF2;
+        f_lo2 = (f_lo2/50)*50;
+
+#ifdef MT2060_SPURCHECK
+        // LO-related spurs detection and correction
+        num1   = mt2060_spurcheck(f_lo1,f_lo2,IF2);
+        f_lo1 += num1;
+        f_lo2 += num1;
+#endif
+        //Frequency LO1 = 16MHz * (DIV1 + NUM1/64 )
+        div1 = f_lo1 / FREF;
+        num1 = (64 * (f_lo1 % FREF)  )/FREF;
+
+        // Frequency LO2 = 16MHz * (DIV2 + NUM2/8192 )
+        div2 = f_lo2 / FREF;
+        num2 = (16384 * (f_lo2 % FREF) /FREF +1)/2;
+
+        if (freq <=  95000) lnaband = 0xB0; else
+        if (freq <= 180000) lnaband = 0xA0; else
+        if (freq <= 260000) lnaband = 0x90; else
+        if (freq <= 335000) lnaband = 0x80; else
+        if (freq <= 425000) lnaband = 0x70; else
+        if (freq <= 480000) lnaband = 0x60; else
+        if (freq <= 570000) lnaband = 0x50; else
+        if (freq <= 645000) lnaband = 0x40; else
+        if (freq <= 730000) lnaband = 0x30; else
+        if (freq <= 810000) lnaband = 0x20; else lnaband = 0x10;
+
+        b[0] = REG_LO1C1;
+        b[1] = lnaband | ((num1 >>2) & 0x0F);
+        b[2] = div1;
+        b[3] = (num2 & 0x0F)  | ((num1 & 3) << 4);
+        b[4] = num2 >> 4;
+        b[5] = ((num2 >>12) & 1) | (div2 << 1);
+
+        dprintk("IF1: %dMHz",(int)if1);
+        dprintk("PLL freq: %d  f_lo1: %d  f_lo2: %d  (kHz)",(int)freq,(int)f_lo1,(int)f_lo2);
+        dprintk("PLL div1: %d  num1: %d  div2: %d  num2: %d",(int)div1,(int)num1,(int)div2,(int)num2);
+        dprintk("PLL [1..5]: %2x %2x %2x %2x %2x",(int)b[1],(int)b[2],(int)b[3],(int)b[4],(int)b[5]);
+
+        mt2060_writeregs(state,b,6);
+
+        //Waits for pll lock or timeout
+        i=0;
+        do {
+                mt2060_readreg(state,REG_LO_STATUS,b);
+                if ((b[0] & 0x88)==0x88) break;
+                msleep(4);
+                i++;
+        } while (i<10);
+
+        return ret;
+}
+EXPORT_SYMBOL(mt2060_set);
+
+/* from usbsnoop.log */
+static void mt2060_calibrate(struct mt2060_state *state)
+{
+        u8 b = 0;
+        int i = 0;
+
+        if (mt2060_writeregs(state,mt2060_config1,sizeof(mt2060_config1)))
+                return;
+        if (mt2060_writeregs(state,mt2060_config2,sizeof(mt2060_config2)))
+                return;
+
+        do {
+                b |= (1 << 6); // FM1SS;
+                mt2060_writereg(state, REG_LO2C1,b);
+                msleep(20);
+
+                if (i == 0) {
+                        b |= (1 << 7); // FM1CA;
+                        mt2060_writereg(state, REG_LO2C1,b);
+                        b &= ~(1 << 7); // FM1CA;
+                        msleep(20);
+                }
+
+                b &= ~(1 << 6); // FM1SS
+                mt2060_writereg(state, REG_LO2C1,b);
+
+                msleep(20);
+                i++;
+        } while (i < 9);
+
+        i = 0;
+        while (i++ < 10 && mt2060_readreg(state, REG_MISC_STAT, &b) == 0 && (b & (1 << 6)) == 0)
+                msleep(20);
+
+        if (i < 10) {
+                mt2060_readreg(state, REG_FM_FREQ, &state->fmfreq); // now find out, what is fmreq used for :)
+                dprintk("calibration was successful: %d",state->fmfreq);
+        } else
+                dprintk("FMCAL timed out");
+}
+
+/* This functions tries to identify a MT2060 tuner by reading the PART/REV register. This is hasty. */
+int mt2060_attach(struct mt2060_state *state, struct mt2060_config *config, struct i2c_adapter *i2c,u16 if1)
+{
+        u8 id = 0;
+        memset(state,0,sizeof(struct mt2060_state));
+
+        state->config = config;
+        state->i2c = i2c;
+        state->if1_freq = if1;
+
+        if (mt2060_readreg(state,REG_PART_REV,&id) != 0)
+                return -ENODEV;
+
+        if (id != PART_REV)
+                return -ENODEV;
+
+        printk(KERN_INFO "MT2060: successfully identified\n");
+
+        mt2060_calibrate(state);
+
+        return 0;
+}
+EXPORT_SYMBOL(mt2060_attach);
+
+MODULE_AUTHOR("Olivier DANET");
+MODULE_DESCRIPTION("Microtune MT2060 silicon tuner driver");
+MODULE_LICENSE("GPL");