drivers/leds/leds-lp5521.c: adjust delays and add comments to them

Delays were little bit too long.  Adjust delay times and add some comments
to them.

Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1 files changed, 16 insertions, 9 deletions

diff --git a/drivers/leds/leds-lp5521.c b/drivers/leds/leds-lp5521.c
index fe69e5229a57..963c014be0bf 100644
--- a/drivers/leds/leds-lp5521.c
+++ b/drivers/leds/leds-lp5521.c
@@ -196,14 +196,17 @@ static int lp5521_load_program(struct lp5521_engine *eng, const u8 *pattern)
 
         /* move current engine to direct mode and remember the state */
         ret = lp5521_set_engine_mode(eng, LP5521_CMD_DIRECT);
-        usleep_range(1000, 10000);
+        /* Mode change requires min 500 us delay. 1 - 2 ms  with margin */
+        usleep_range(1000, 2000);
         ret |= lp5521_read(client, LP5521_REG_OP_MODE, &mode);
 
         /* For loading, all the engines to load mode */
         lp5521_write(client, LP5521_REG_OP_MODE, LP5521_CMD_DIRECT);
-        usleep_range(1000, 10000);
+        /* Mode change requires min 500 us delay. 1 - 2 ms  with margin */
+        usleep_range(1000, 2000);
         lp5521_write(client, LP5521_REG_OP_MODE, LP5521_CMD_LOAD);
-        usleep_range(1000, 10000);
+        /* Mode change requires min 500 us delay. 1 - 2 ms  with margin */
+        usleep_range(1000, 2000);
 
         addr = LP5521_PROG_MEM_BASE + eng->prog_page * LP5521_PROG_MEM_SIZE;
         i2c_smbus_write_i2c_block_data(client,
@@ -244,7 +247,10 @@ static int lp5521_configure(struct i2c_client *client,
 
         lp5521_write(client, LP5521_REG_RESET, 0xff);
 
-        usleep_range(10000, 20000);
+        usleep_range(10000, 20000); /*
+                                     * Exact value is not available. 10 - 20ms
+                                     * appears to be enough for reset.
+                                     */
 
         /* Set all PWMs to direct control mode */
         ret = lp5521_write(client, LP5521_REG_OP_MODE, 0x3F);
@@ -262,8 +268,8 @@ static int lp5521_configure(struct i2c_client *client,
         ret |= lp5521_write(client, LP5521_REG_ENABLE,
                         LP5521_MASTER_ENABLE | LP5521_LOGARITHMIC_PWM |
                         LP5521_EXEC_RUN);
-        /* enable takes 500us */
-        usleep_range(500, 20000);
+        /* enable takes 500us. 1 - 2 ms leaves some margin */
+        usleep_range(1000, 2000);
 
         return ret;
 }
@@ -316,7 +322,8 @@ static int lp5521_detect(struct i2c_client *client)
                         LP5521_MASTER_ENABLE | LP5521_LOGARITHMIC_PWM);
         if (ret)
                 return ret;
-        usleep_range(1000, 10000);
+        /* enable takes 500us. 1 - 2 ms leaves some margin */
+        usleep_range(1000, 2000);
         ret = lp5521_read(client, LP5521_REG_ENABLE, &buf);
         if (ret)
                 return ret;
@@ -704,9 +711,9 @@ static int lp5521_probe(struct i2c_client *client,
 
         if (pdata->enable) {
                 pdata->enable(0);
-                usleep_range(1000, 10000);
+                usleep_range(1000, 2000); /* Keep enable down at least 1ms */
                 pdata->enable(1);
-                usleep_range(1000, 10000); /* Spec says min 500us */
+                usleep_range(1000, 2000); /* 500us abs min. */
         }
 
         ret = lp5521_detect(client);