ide-pmac: remove pmac_ide_do_setfeature() (take 2)

Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also  ide-iops.c::__ide_wait_stat() could be static again.

Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:

* if PIO mode is set then ->dma_off_queitly is called to disable DMA

* if setting transfer mode fails ide_dump_status() is called to dump status

v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
  depends on this fact, and calls "hdparm -p" without calling "hdparm -d".

  Therefore to compensate for DMA being disabled by ide_config_drive_speed()
  for PIO modes:

  - add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver

  - add handling of the new flag to ide-io.c::do_special()

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 3 insertions, 77 deletions

diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index c68e2472345a..24f73291c4d5 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -530,81 +530,6 @@ pmac_outbsync(ide_drive_t *drive, u8 value, unsigned long port)
 }
 
 /*
- * Send the SET_FEATURE IDE command to the drive and update drive->id with
- * the new state. We currently don't use the generic routine as it used to
- * cause various trouble, especially with older mediabays.
- * This code is sometimes triggering a spurrious interrupt though, I need
- * to sort that out sooner or later and see if I can finally get the
- * common version to work properly in all cases
- */
-static int
-pmac_ide_do_setfeature(ide_drive_t *drive, u8 command)
-{
-        ide_hwif_t *hwif = HWIF(drive);
-        int result;
-        u8 stat;
-        
-        disable_irq_nosync(hwif->irq);
-        udelay(1);
-        SELECT_DRIVE(drive);
-        SELECT_MASK(drive, 0);
-        udelay(1);
-        hwif->OUTB(drive->ctl | 2, IDE_CONTROL_REG);
-        hwif->OUTB(command, IDE_NSECTOR_REG);
-        hwif->OUTB(SETFEATURES_XFER, IDE_FEATURE_REG);
-        hwif->OUTBSYNC(drive, WIN_SETFEATURES, IDE_COMMAND_REG);
-        result = __ide_wait_stat(drive, drive->ready_stat,
-                                 BUSY_STAT|DRQ_STAT|ERR_STAT,
-                                 WAIT_CMD, &stat);
-        if (result)
-                printk(KERN_ERR "%s: pmac_ide_do_setfeature disk not ready "
-                        "after SET_FEATURE !\n", drive->name);
-
-        SELECT_MASK(drive, 0);
-        if (result == 0) {
-                drive->id->dma_ultra &= ~0xFF00;
-                drive->id->dma_mword &= ~0x0F00;
-                drive->id->dma_1word &= ~0x0F00;
-                switch(command) {
-                        case XFER_UDMA_7:
-                                drive->id->dma_ultra |= 0x8080; break;
-                        case XFER_UDMA_6:
-                                drive->id->dma_ultra |= 0x4040; break;
-                        case XFER_UDMA_5:
-                                drive->id->dma_ultra |= 0x2020; break;
-                        case XFER_UDMA_4:
-                                drive->id->dma_ultra |= 0x1010; break;
-                        case XFER_UDMA_3:
-                                drive->id->dma_ultra |= 0x0808; break;
-                        case XFER_UDMA_2:
-                                drive->id->dma_ultra |= 0x0404; break;
-                        case XFER_UDMA_1:
-                                drive->id->dma_ultra |= 0x0202; break;
-                        case XFER_UDMA_0:
-                                drive->id->dma_ultra |= 0x0101; break;
-                        case XFER_MW_DMA_2:
-                                drive->id->dma_mword |= 0x0404; break;
-                        case XFER_MW_DMA_1:
-                                drive->id->dma_mword |= 0x0202; break;
-                        case XFER_MW_DMA_0:
-                                drive->id->dma_mword |= 0x0101; break;
-                        case XFER_SW_DMA_2:
-                                drive->id->dma_1word |= 0x0404; break;
-                        case XFER_SW_DMA_1:
-                                drive->id->dma_1word |= 0x0202; break;
-                        case XFER_SW_DMA_0:
-                                drive->id->dma_1word |= 0x0101; break;
-                        default: break;
-                }
-                if (!drive->init_speed)
-                        drive->init_speed = command;
-                drive->current_speed = command;
-        }
-        enable_irq(hwif->irq);
-        return result;
-}
-
-/*
  * Old tuning functions (called on hdparm -p), sets up drive PIO timings
  */
 static void
@@ -685,7 +610,7 @@ pmac_ide_set_pio_mode(ide_drive_t *drive, const u8 pio)
                 drive->name, pio,  *timings);
 #endif  
 
-        if (pmac_ide_do_setfeature(drive, XFER_PIO_0 + pio))
+        if (ide_config_drive_speed(drive, XFER_PIO_0 + pio))
                 return;
 
         pmac_ide_do_update_timings(drive);
@@ -948,7 +873,7 @@ static int pmac_ide_tune_chipset(ide_drive_t *drive, const u8 speed)
         if (ret)
                 return ret;
 
-        ret = pmac_ide_do_setfeature(drive, speed);
+        ret = ide_config_drive_speed(drive, speed);
         if (ret)
                 return ret;
 
@@ -1218,6 +1143,7 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
         hwif->cbl = pmif->cable_80 ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
         hwif->drives[0].unmask = 1;
         hwif->drives[1].unmask = 1;
+        hwif->host_flags = IDE_HFLAG_SET_PIO_MODE_KEEP_DMA;
         hwif->pio_mask = ATA_PIO4;
         hwif->set_pio_mode = pmac_ide_set_pio_mode;
         if (pmif->kind == controller_un_ata6