[PATCH] IRQ type flags

Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels.  For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.

Currently, ARM drivers do (eg) the following:

	err = request_irq(irq, ...);

	set_irq_type(irq, IRQT_RISING);

However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.

Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt.  The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.

Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like.  The IRQ controller code should do its
best to select the most appropriate supported mode.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

1 files changed, 6 insertions, 5 deletions

diff --git a/drivers/i2c/chips/tps65010.c b/drivers/i2c/chips/tps65010.c
index e70b3db69edd..1af3dfbb8086 100644
--- a/drivers/i2c/chips/tps65010.c
+++ b/drivers/i2c/chips/tps65010.c
@@ -494,6 +494,7 @@ tps65010_probe(struct i2c_adapter *bus, int address, int kind)
 {
         struct tps65010         *tps;
         int                     status;
+        unsigned long           irqflags;
 
         if (the_tps) {
                 dev_dbg(&bus->dev, "only one %s for now\n", DRIVER_NAME);
@@ -520,13 +521,14 @@ tps65010_probe(struct i2c_adapter *bus, int address, int kind)
         }
 
 #ifdef  CONFIG_ARM
+        irqflags = SA_SAMPLE_RANDOM | SA_TRIGGER_LOW;
         if (machine_is_omap_h2()) {
                 tps->model = TPS65010;
                 omap_cfg_reg(W4_GPIO58);
                 tps->irq = OMAP_GPIO_IRQ(58);
                 omap_request_gpio(58);
                 omap_set_gpio_direction(58, 1);
-                set_irq_type(tps->irq, IRQT_FALLING);
+                irqflags |= SA_TRIGGER_FALLING;
         }
         if (machine_is_omap_osk()) {
                 tps->model = TPS65010;
@@ -534,7 +536,7 @@ tps65010_probe(struct i2c_adapter *bus, int address, int kind)
                 tps->irq = OMAP_GPIO_IRQ(OMAP_MPUIO(1));
                 omap_request_gpio(OMAP_MPUIO(1));
                 omap_set_gpio_direction(OMAP_MPUIO(1), 1);
-                set_irq_type(tps->irq, IRQT_FALLING);
+                irqflags |= SA_TRIGGER_FALLING;
         }
         if (machine_is_omap_h3()) {
                 tps->model = TPS65013;
@@ -542,13 +544,12 @@ tps65010_probe(struct i2c_adapter *bus, int address, int kind)
                 // FIXME set up this board's IRQ ...
         }
 #else
-#define set_irq_type(num,trigger)       do{}while(0)
+        irqflags = SA_SAMPLE_RANDOM;
 #endif
 
         if (tps->irq > 0) {
-                set_irq_type(tps->irq, IRQT_LOW);
                 status = request_irq(tps->irq, tps65010_irq,
-                        SA_SAMPLE_RANDOM, DRIVER_NAME, tps);
+                        irqflags, DRIVER_NAME, tps);
                 if (status < 0) {
                         dev_dbg(&tps->client.dev, "can't get IRQ %d, err %d\n",
                                         tps->irq, status);